Audio exporting problems: from FCP to protool/STP and back again

--------------------------------------------------------------------------------
Final Cut Pro sound export for mastering.....sync problem
Hey,
I'm editing a 30 minute film and I have done most of the sound edit in FCP and Soundtrack pro and I want to now bring all the sound into pro tools to master the sound but every time i export sound into pro tools it seems to stretch by two or three seconds.
I have tried OMF, AIFF, XML, and Quicktime audio file sut to no avail!!!!
There are 50 tracks in the file so it is quiet large. It's not that there are handles of the file also as when I sync the file with the audio track with the video it syncs in one place but it is still out of sync in another.........It's as if the audio has been stretched!?!
If anyone has any advice it'd be much appreciated
Keith

Check the timecode rate and sync options in Protools. It sounds like a timecode or samplerate mismatch.
Especially note that 23.976fps OMFs from FCP (probably STP as well) show up in Protools as 24fps sessions. Change the PTs timecode to 23.976 to realign.

Similar Messages

Blue screen of death, and continous reboot. Phone never actually boots up, just keeps going from reboot to blue screen and back again. Any suggestion?

Blue screen of death, and continous reboot. Phone never actually boots up, just keeps going from reboot to blue screen and back again. Any suggestion?

Hello jared1915
If you are stuck in that loop, the next step would be to restore your iPhone. Check out the article below to get your iPhone into recovery-mode and restore it in iTunes.
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
Regards,
-Norm G.

Best way to go from FCP to After Effects and back?

Hi guys,
What's the best way to go from FCP (5) to AE (7)? I'm exporting as a Quicktime Movie, but not self-contained. Then from AE I make a Quicktime Movie
and drag it back to FCP.
Is this the best method?
Thanks
G5 Quad Mac OS X (10.4.6) Dell 2405

Thanks Cap'n, but am I losing any resolution this way? And should I be including or excluding markers?
That is one rich little duck! :P
G5 Quad Mac OS X (10.4.6) Dell 2405

XDCam footage exported from FCP to After Effects and back to FCP stutters

I need help. Here is the situation:
XDCam footage imported into Final Cut with the Sony Import Software 25 mpbs. Final Cut sequence is set up to match all settings. The footage is placed into the sequence fine, I can edit with no problems everything works great. The problems start when I export from Final Cut to bring it into After Effects 7.0.
I drag the imported footage onto the comp icon to create a new comp with the footage settings. The footage is being interpreted as upper field first. I render out the footage using the HDV codec that matches my sequence in Final Cut. When I import the rendered movie into Final Cut it causes the whole system to bog way down. Not just dropped frames but a serious amount of bog down, I even get the spinning Beachball for a few seconds while its trying to play. It should be noted that when I place the rendered movie in the sequence it doesn't seem to need any rendering. Now, here's the weird part, when I play the rendered movie using just the quicktime app. It plays just fine. The problem only seems to be with Final Cut.
any suggestions?

Hi,
I was having the same problem. After studying the mov as rendered by AE it would seem that there's something odd about the framsize. It would seem that AE's HDV preset is incompatible with FCP for some reason. There's probably a perfectly reason tech explanation for this but I don't know it.
I was told by a friend to always render 'intermediate codec' which I intend to do in future.
As a short-term measure just run the files through Compressor, that did the trick for me.

How can I transfer my 'pages' from mac to I-pad and back again?

Hi, how can I use the 'Pages' on both my desktop and the I-Pad? I've tried using DropBox but it doesn't seem to work with Pages? Any other ideas?

This is how it works if your iPad is connected to your Mac and you want to sync back and forth.
Find the document in Pages on your iPad that you want to transfer to your Mac. Click on the curved arrow icon at the bottom of the window and a dialog box pops up with several options. You can choose any of these options to send the file to your Mac. The third option, the one that I use, is send to iTunes. Tap that icon, select the file type that you want to use for the document (Pages, pdf, .doc) connect your iPad to your Mac, launch iTunes, select your device on the left side of iTunes. Then select Apps in the top of the iTunes window and scroll down to the File Sharing box. Select Pages and then sync. That document will now be transferred to your Mac and you will see it on the right side the box called Pages Documents.
To go from the Mac to the iPad, (while the ipad is connected to your Mac as described above) select Pages in the File Sharing box, then click on Add in the lower right corner of the Pages document box, select the file that you want to transfer to your iPad, tap the down arrow icon in Pages on your iPad, select Copy from iTunes, and the file name will appear. Tap on that file and it will transfer.
Message was edited by: Demo

Having trouble switching from Photobucket to a forum and back again without losing my post.

I am so frustrated and I hope someone can help.
I need help adding pictures from Photobucket to a forum. I write a story on a forum and store my photos in Photobucket. On my old computer I was able to keep my photobucket page open in a small window and my post from the forum open in another small window. Then I was able to go back and forth between the two. I would write some of my story, go into PB and copy a picture, go back to my post, add the picture, write some more and do it again about 20 more times.
Now on my Mac:
I tried to hit the green minus to keep my photobucket page up but when I tried to go to my forum page I only got Safari and then it closed my photobucket page.
So then I tried ot use the scroll between pages to go back and forth between my post and photobucket. I got my story started, went into PB, copied a picture and pasted it onto my story then I scrolled back to PB to get a new picture...but when I scrioled back my entire post was gone. It didn't save anything that I typed or added. This will not work for me. There has to be an easier way...heck just a way to do it would make me happy.
So please if anyone knows how to do this, I would really appreciate the help.

Hi SLONER,
You need use the -source option on a non-Internet connected machine.
PLease try the script below:
Install-WindowsFeature Server-Gui-Mgmt-Infra,Server-Gui-Shell –Restart –Source c:\mountdir\windows\winsxs
And follow this thread:
PowerShell to Add GUI to Server Core (ServerCore-FullServer)
I hope this helps.

Exporting text from fcp

I have a lot of separate text boxes in my sequence. Since I can' t do a spell check in fcp, I was wondering if i can export all the text boxes out as a plain text document to do a spell check.
I tried exporting as a xml document, but navigating through all the tags was quite a problem.
TIA for any suggestions.

Usual workflow is following.
1. Put all Text-generator clips to one track
2. Export sequence to XML
3. Launch TitleExchange, point to exported XML and say where to put converted file.
Exporting to STL you'll get text file like that
+00:01:27:26 ,00:01:29:26 ,They had this idea that+
+00:01:29:30 ,00:01:30:31 ,behind scary+
... which you can open in any spell-checker.
We use TitleExchange to bring subtitles from FCP to DVD Studio and back (in case we need subtitled DVD and Betacam output)
Though, this may be much expensive way of checking spelling (135 Euro per TE licence).
There are lots of subtitle software, I only wanted to mention a way of exporting text from FCP with help of subtitle processors.

CS4 Audio Export Problem

Hi
I'm fairly new to CS4 and have picked up an audio export problem, more than likely with a setting of sorts. For some reason when I export to MPEG2 -DVD via the Media Encoder, the video portion is fine as well as any audio that has been placed and edited on tracks audio 1 and 2 in PP. However, if there is additional audio placed on tracks 3 or 4 for example (say a music MP3 overlay) then this does not come out ... only audio placed on tracks 1 and 2 in PP come out. I have checked the obvious like making sure the tracks aren't muted etc but to no avail. Also tried changing from PCM audio to MPEG ... Stereo to 5.1 mixdown ... nothing doing.
Any help would be greatly appreciated.
Thanks and regards
Videoman 1
SA

Thanks Harm ... got SnagIt and with a few helpful YouTube tutorials ... am in business. Hunt and John, also thanks ... the other method equally as good. Now, I have attempted to attach my screen shot which should display my CS4 timeline and associated audio monitor windows above. By the way, this was for a wedding and as indicated, you will notice an MP3 lying in audio track 3 which as mentioned is my problem as it is not audible after render via Media Encoder. But remember, the moment I slip this MP3 up into audio track 1 or 2 above ... problem solved. I know there must be something small like a setting gone wrong or incorrect. As mentioned, any help would greatly appreciated.
Thanks to you all.
Regards Paul ( Vryheid, South Africa )

Can the exported video from FCP X play in WMV?

(1) Can the exported video from FCP X play in WMV?
(2) If not, can I convert with the help of Compressor 4 to make it to play in WMV?

No to both. You need third party software to create WMV. Telestream has tools for this.

NTSC to PAL - Export straight from FCP or use an mpeg file?

I was reading this
http://www.macworld.com/article/49306/2006/02/marchcreate.html
however it does not mention what to bring into compressor.
Should I export my ntsc sequence straight from FCP into compressor, or should I drag an ntsc mpeg file I aldeady made into compressor? Ive been trying the latter but can't do much as each step gives me the spinning beach ball for anywhere from 5 to 10 minutes. Thanks much.

Yes, you should export directly from FCP Using Compressor. Exporting to a heavily compressed MPEG-file, and then converting that from NTSC to PAL makes no sense. You would want your video to go through as few conversions/generations as possible.

Exporting quicktimes from FCP to iDVD?

I am having trouble exporting quicktimes from FCP and bringing them into iDVD.
How do you make Chapter Markers on an export from FCP?

When creating chapter markers, make sure nothing is slected within your timeline (click in a blank space before hitting m). Hit m again and click chapter marker button.
When exporting your sequence, be sure to select Markers > Chapter Markers on the export dialog popup.

Problems with FCP 5.1.4 and OSX 10.4.9

I upgraded to Tiger, installed the new FCP Studio and everything was working fantastic.
The next morning there was a software update for Tiger and FCP-5.1.4, it's been a nightmare ever since. When I restarted FCP would not recognize my Sony HDR FX1.
I had this problem once before with 4.5 and I fixed it by re-installing FCP and doing the upgrades, so that's what I did with 5 but this time there was a new problem. It wouldn't let me work on anything that I had opened since I did the software update, so I had to do the update again and then FCP wouldn't recognize my camcorder again on startup. If you pressed log and capture you could control the camera but no capture was possible.
So I re-set the easy set-up and presto! everything was fine and I worked productively for a few days.
But then I had to capture some SD from my Canon GL2 so I reset all the settings for DV NTSC and reset the easy set-up for DV NTSC but now FCP won't recognize my GL2 on start-up. If I click log and capture I can control the camera but no capture.
My next try to solve my problem was to downgrade back to my original 10.4.6 and FCP 5.1
That put be back to square one and everything works fine again except I am left with the problem that everything that I worked on after I did the update won't open, I get error 41.
Now I know this is because I am now trying to work on these projects with 5.1 after they were worked on in 5.1.4. But the problem is that everytime I update to 5.1.4 I can no longer capture or print to tape.
I tried the trashing the FCP prefs thing and the repairing permissions thing but I can't seem to solve the problem.
Has anyone else had any problems using FCP 5.1.4 and OSX 10.4.9?

Not sure how you tried to install 10.4.8 but if all
else fails you can always reinstall the original
operating system that came with your Mac using 'Erase
and Install' then upgrade it to 10.4.8 - probably in
stages.
Erase and install should be used as a last resort! A better option is to use the "archive and install" feature. It renames your old system folder and creates a new one for the OS you just re-installed. That way you don't have to reinstall everything, your user accounts and emails should all still be there, and if something doesn't work, you have your old system folder to pull things like preference files out of.
Eric

My iPhone is split from front panel on top, and back cover of my is swollen too. I am not able to use my phone and I cannot access my data in the phone. Please suggest what could be the cause of this problem?

My iPhone is split from front panel on top, and back cover of my is swollen too. I am not able to use my phone and I cannot access my data in the phone. Please suggest what could be the cause of this problem?

It sounds like the battery might have gone bad, and is swelling and causing the symptoms you describe. Do not attempt to use the phone, but take it to Apple for evaluation.

Is it possible to export contacts from Outlook 2011 for Mac and importing this file back into Mac Address Book.? please reply me its urgent

Is it possible to export contacts from Outlook 2011 for Mac and importing this file back into Mac Address Book.? please reply me its urgent

Is it possible to export contacts from Outlook 2011 for Mac and importing this file back into Mac Address Book.? please reply me its urgent

When mousing over text, the cursor flickers constantly (with each letter passed) from arrow to i-beam and back. The problem occurs in both MS Word and Pages. Any idea of how to resolve this annoying problem is appreciated. System: 10.10.1

When mousing over text, the cursor flickers constantly (with every letter passed) from arrow to i-beam and back. The problem occurs in both MS Word 2011 and Pages. Any idea of how to solve this annoying problem will be much appreciated. System 10.10.1 on a MacPro (Late 2013)

The mouse is controlled by the OS so don't guess any app other than a mouse driver or OS X itself would be able to cause this sort of flicker issue.
Have you seen the following and is it what you are seeing? Maybe you could make a movie (Quicktime is great for this this to make a screen recording) - but not sure how to attach a movie to these discussions as mine is grayed out and can't be selected (to the right of the insert image). Here is the what I found for a search of "mouse cursor flickers os x yosemite"
https://www.youtube.com/watch?v=ZNQ0D84DdF4
What kind of mouse are you using? Is the mouse driver up to date if it's a third party mouse?

Audio exporting problems: from FCP to protool/STP and back again

Similar Messages

Maybe you are looking for