Audio going out randomly through front & rear jack during VLC & Mplayer

When I play a movie on VLC or mplayer it shuts down the audio of the VLC player as well as the entire audio of the computer.
I have to pull the headphone jack out then plug it back in for the audio to go back on.
Any thoughts?
I have changed my speakers... My amp.. my wires. even tried the front and back jack.
It only happens during VLC or mplayer?
But happens more during VLC.
I thought maybe it was the jack but it happens at both jack.
Then I switched wires... no go.
My amp works fine on all other electronics even a second computer,
Thought it was VLC then it happens on Mplayer.
It happens on no other application tho.
and it shuts the audio of all functions of my computer down until i pull the jack in and out.
Could it be my sound board?
any thoughts?

Well I changed it back to 44.1 however it still happens even on 44.1
I am not sure why its happening.
It only happens when playing avi in VLC and Mplayer.
the MIDI setup helps me reset the audio instead of pull the headphone in and out.
but its getting annoying

Similar Messages

Audio goes out on my Air after I unplug my headphones.

Audio goes out on my Air after I unplug my headphones. Reset did not fix it.

Hi johnfan1939,
Although this article specifically mentions the iPhone, many of the steps apply for the iPad as well.
iPhone: No sound or distorted sound from speaker
Verify that the volume is set to a level you would normally be able to hear.
Ensure that there is nothing plugged in to the headset jack or the dock connector.
If the iPhone is in a protective case, make sure that the speaker port isn't blocked by the case.
Make sure that the speaker and dock port aren't clogged with debris. If necessary, clean it with a clean, small, dry, soft-bristled brush. Carefully and gently brush away any debris.
If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
If the iPhone is paired with a Bluetooth headset or car kit:Restart the iPhone.Restart the iPhone.
Try turning off Bluetooth.
If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
Restart the iPhone.
If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
If the issue is not resolved, please contact Apple Support.
Best Regards,
Nubz

During editing on MacBook Pro 2.2GHz i7, audio goes out of sinc with video

I have been having a lot of trouble with audio going out of sinc after I have edited a 30 minute program. When I make a second cut, I find that the audio has jumped under the first cut about half an inch back, and this happens with every progressive cut. Then after "sharing" to dvd the audio is out of sinc with video throughout. I then have moved each one of these overlaps back into position and still have a problem with audio out of sinc.
HELP.

I was using a different laptop for post since the macbook was busy "sharing" to dvd, which, since I closely examined each cut at highest magnification to fix them ended up making video watchable. Not every cut came out of sinc, but several do.
It is both sides of the cut which come out of sinc, the right side laps over the left and then I noticed when I corrected them with greater magnification that the left side was moved left to cause a gap. I guess I just have to closely examine each cut when done with the whole video since also these overlaps are caused when I zoom out to view the whole length of the timeline, most of the cuts will overlap at that moment. Really strange. I had trouble fixing these but less trouble whe I turned off the snap in option.

Video and audio goes out of sync when imported into Premiere

I have some videos ripped from some DVD that an acquaintance made, with an open source program called HandBrake, with the default "high profile" settings. When I play it both in VLC and in Quicktime, it plays just fine, but when I import it either in Premiere or in After effects, the video and audio goes out of sync (the video ran faster than the audio and when the video stops, the missing audio is trimmed).
Video info according to Premiere (in Spanish but you may get the meaning).
Ruta del archivo: [...].m4v
Tipo: Película MPEG
Tamaño de archivo: 667,7 MB
Tamaño de la imagen: 720 x 480
Profundidad en píxeles: 32
Velocidad de fotograma: 29,97
Formato de audio de origen: 48000 Hz - comprimido - Estéreo
Formato de audio del proyecto: 48000 Hz - Punto flotante de 32 bits - Estéreo
Duración total: 00:30:35:15
Velocidad media de datos: 372 KB / segundos
Proporción de píxeles: 0,8889

"HandBrake, these days, is almost entirely about H.264 video, aka MPEG-4 Part 10. HandBrake is migrating to quality-based encoding."
Hmmm. I use HC Encoder to make my DVDs because it's the only free encoder I've found with the much more professional Constant Q encoding option. But HC Encoder doesn't do HD sources for Blu-ray, so I've been wondering if I'd be stuck with the lame-*** consumer CBR and VBR options most encoders provide (including Adobe - hint, hint) when I eventually start working in HD. This is a very interesting program, Handbrake. I will have to check it out.

When audio goes out of sync..

In FCP7, when audio goes out of sync with the video track it came from (even when they are unlinked), a red warning box is displayed on the audio track and tells you how far out of sync it is, which easily enables you to resync.
Well, in FCX my audio went out of synce, but i didn't know it until i played back a segment i was working on, where i spliced two audio tracks and video tracks together. Right now i'm trying to fix the one audio track so that is synced up with its parent video track, but so far i'm just guessing that it's a good sync rather than knowing FOR SURE whether or not it's truly synced back up.
Is there any kind of work around, which enables you to resync in a manner similar to before FCPX?
Thanks

I am not sure if your problem has been solved already but here is the way to do that:
select in the clip in the timeline the part were the audio should be return in sync. use the blade-tool to make that part a seperate clip.
Higlight this clip in the timeline and use shift-F to highlight this clip in the browser. There it wil show up partially of course.
Use only the audio and put that part under the selected clip in the timeline where you need the original audio. remove the original out-of-sync audio.

Audio sync problems with greenscreen I have replaced the camera audio with my zoom recorder audio and it is in sync. When I apply greenscreen the audio goes out of sync. What am i doing wrong?? So frustrating..Thanks, Peter

I have replaced the DSLR audio with audio from my Marantz recorder and it is in sync with the dialogue. I apply green screen and the audio goes out of sync. Cannot seem to make it work. what am I doing wrong? Thanks, Peter

Thanks for the reply. I don't have time for this. is it time to switch to a different editor?

HELP! Audio goes out of sync after export!

OK, folks. I need your help. I have a looming deadline of THIS FRIDAY to hand this in.
I have a finished multicam edit of a show that runs 1 hr 20 min. It plays back perfectly in the timeline, all video and audio perfectly in sync. Looks and sounds exactly like what I need.
When I export the video as an H.264 file, the audio gets out of sync with the video by 13 frames! But that's not all... It doesn't happen to the entire audio track. There's about 50 minutes in the middle of the video where the audio goes out of sync. The audio at the beginning and ending of the video is lined up perfectly in sync. It's just the middle section that gets screwy.
What do I do?!
This has never happened before, and I've worked a lot with multicam in Premiere Pro CC before this. Never been an issue. I tried uninstalling and reinstalling Premiere, and also deleting all media cache files, but still no dice. I also tried copying the clips into a new sequence in the same project, copying the clips into a new sequence in a NEW project, nesting the sequence... nothing works.
My setup:
MacBook Pro Retina (Rev. A)
Premiere Pro CC (latest version)
Panasonic GH3 footage in 1080p 24p AVCHD timeline
3 cameras & 1 audio WAV file in Multicam
Any help would be greatly appreciated!

OK, I figured out how to fix it:
In Premiere Pro CC, click on SEQUENCE > DELETE RENDER FILES.
Try exporting the movie again.
It worked! I exported the same sequence, and it took a long while to re-render the audio files, but when it was finished exporting the audio and video were in perfect sync. I'm not sure what caused it, but this fixed it, so hopefully anyone else having this issue can save a lot of time by reading this.
Cheers!

Unable to share to youtube and audio goes out of sync

hey,
Im trying to upload a video to youtube.
So, i clicked * Share - Youtube *
And after about 30 minutes it notified me that the upload was complete… Well i went on youtube and checked & my video wasn't upload… i tried again, and still nothing happened…
So i decided to export the movie to a file, and manually upload it .. when i watch the video on my computer.. it's plays perfectly.. but for some reason.. when i upload it to youtube the audio goes off ,
Random audio that i deleted plays… and audio from one clip plays over another..
PLEASE HELP
How do i fix this ? i just want to upload a normal video to youtube…
Thanks
~Chris
Message was edited by: Youtuber
Message was edited by: Youtuber

I have the feeling there isn't a real solution for many of us who are having this problem.
I just gave up and exported to the desktop, and then used YouTube's uploader, which works fine.
Sorry, I don't have a fix, but wanted to add my voice as someone who has tried a lot of ways with his iMac, and figured it wasn't worth all the hassle. YouTube's uploader lets me upload many clips at once, add commentary, and then go do something else, sure that it will go ok. I had the iMovie-YouTube link working for a bit, but then it went all haywire again.
Hugh

Screen on my Mac Book Pro goes out randomly when I touching trackpad.

The screen on my Mac Book Pro goes out randomly when I touch my trackpad. Every time the screen shuts off, I have to restart my computer so the screen will turn on again and it's driving me nuts.
Does anyone have any idea why this is happening and a solution?
Thanks
Kevin

You can blank the monitor using those keys, that's likely what you did, it's a feature.

Audio drops out randomly in FCP5

Hello,
I'm running FCP 5.0.4 on a G5 OSX 10.3.9 and a AJA io LA with current firmware v1.1 and driver v2.1.
When playing a sequence, audio will be fine. Going from AJA through mixer, to speakers and decks. Then the audio will cut ot completely, but video will continue to play. The meters in FCP show the audio is there, but nothing is getting to the mixer, and therefore nothing is getting onto tape, or coming out of my speakers. This problem occurs in every project we've worked with, and doesn't happen at the same point in the sequence. Any ideas? I'm not sure what other info might be useful, so please request more if you have any ideas. Thank you for your time.
Ben Slocum
KCOY-TV/KKFX-TV

Hi all -- I've experienced this problem on a number of projects, one tonight prompted me to check the forum. I used one of the work-arounds and want to report on it, in case it works for someone else or someone with the FCP development team is reading.
My timeline would drop the audio at a repeatable point each time. If I nested the sequence in another sequence, the audio would play but would have a nasty discontinuity right at the frame where the audio drops out in the original sequence.
I used the transparent video slug work-around and it worked (create a slug, set its transparency to zero and place it over the spot where the audio drops out). This occured twice in my timeline. Both times I had used a certain video clip. I had to stretch the slug to exactly match the duration of the offending video clip in order to keep the audio from dropping out.
This sounds like a bug that should be repeatable and fixed. If anyone with FCP development team wants my project, I would be glad to send it to them on a DVD for investigation. I'm running FCP 5.0.3 on a G5 dual 2.7GHz with an internal SATA drive, so it probably isn't a machine speed issue. (I tried the re-render trick and that didn't work and if I remove the slug or change its duration to anything less than the duration of the offending video clip, the audio drops out again.)
G5 dual 2.7GHz Mac OS X (10.4.4) 4GB RAM

My audio drops out randomly, hers is occasionally ...

For the past year I have frequently used Skype on my Android phone (Nexus 5) to talk to my fiancee on her Windows 8.1 laptop. We do so from our respective homes, so we're both on WiFi to a solid Internet connection (DSL in my case, cable Internet in hers). I'm using the latest Android Skype client (5.0.0.55107) and she's using the latest Windows 8.1 Skype client (6.21.0.104). Ever since the Android 5.0 (Lollipop) update, my audio keeps dropping on her end for no apparent reason.
This happens at random but frequent intervals and for short durations (ca. 30 seconds per episode). It is absolutely maddening. Even though she hasn't changed anything on her Windows 8.1 laptop, and I've reinstalled Skype on my Nexus 5, my audio drops out some of the time during every single call. This happens very often during a call. It's to the point that I can't even open my mouth without expecting that my audio will drop out in the middle of what I'm saying, so that I end up having to repeat myself. If I'm really frustrated, I'll just type what I was going to say.
On the first few calls after my Nexus 5 received the Lollipop update, her audio would also sometimes drop out. We had to hang up and reestablish the call for her audio to come back on my end. Since then, we haven't had that particular problem, but sometimes her voice is garbled - as if I'm only hearing every other syllable - even though she's speaking directly at the microphone. Both systems (phone and laptop) are up to date, latest drivers, latest Skype, etc.
Given that she hasn't changed anything at all on her end, it's rather clear that the latest Skype for Android has a problem. TL;DR: I appear to be "muted" to other caller at random, even though I'm not muting myself, and her voice is occasionally garbled. It happens over and over again during a call, without warning.
Solved!
Go to Solution.

Unfortunately, although my audio is no longer dropping out, we have been unable to use Skype for the last couple of days.
Last night, I could neither receive nor make Skype calls using my phone. If she called, it would only ring on my desktop PC. If I called her, it never rang on her end, and would either ring once or not at all (i.e. the sound effect I normally hear when calling didn't play) and would simply "fail" for no apparent reason.
Skype on my laptop doesn't work well, because there is almost always a problem with my audio being replaced with a "white noise" type sound on her end at random intervals and durations.
So, we had to use Google Hangouts video chat last night. It doesn't work that well either; frequently, there is an absolutely terrible audio feedback/echo problem.
I hope Skype can be made to work again on my phone. I've given up hope of it ever working 100% on my laptop, but I'd rather use it on my phone anyway, as it's far more portable.

Audio goes out of sync when Blu-ray folder is exported from Encore CS6

I compile a project in Encore using H.264 and .wav files. The audio plays fine directly from the timeline. It also plays fine when I preview it from Encore. When I finally export it as a set of Blu-ray folders, the audio exports out of sync with the video. It is approximately 6-7 seconds ahead of the video. What am I doing incorrectly? When I mux the files into an .MKV, the video is in sync with the audio so I know the files themselves do not have different start times.
I am running with an HP Z820 with Windows 7, 64-bit OS and 16GB RAM.

For anyone who's interested, I found a solution to this problem. Once imported into Encore, the leader in on the video and audio files cannot be trimmed at all. (I had been trimming the beginning of the video and matching audio file to eliminate the 8 seconds of dead space at the start of the clips.) Although the trim took effect immediately in the Encore timeline and I could also watch it in preview in sync, exporting was another story. The audio track seems to retain the trim when exporting but the video track does not, hence the 6-7 second delay between audio and video.
I reimported the files to my project and left in the 8 seconds of dead space at the start and voila! The video and audio match up when exported.
Ideally the trim tool would just work as its supposed to through export and all, but at least I found a solution I can work with.
(As a note, the trim works just fine in export on Encore CS5. I only had this problem with Encore CS6.)

AME - Converting to MP4 and different FPS - audio goes out of sync

As described in the title.
I'm reencoding a 1920x1080 29,97 fps video into a 1280x720 60 fps video. Audio is AAC 44100 stereo.
Basicly a task that many of those free converters on Windows do smoothly. I use Mac...
I'm surprised that it goes out of sync, like 3-4 secs EARLY sound on a span of 2 mins video.
Settings here:
AME CS6 Fully updated
source: 1920x1080 29,97fps MP4 with AAC 44100hz audio
Target:
Codec: H264
Saves as : MP4
1280 x 720
60 fps Progressive - NTSC
CBR VBR1 VBR2 doesn't matter
Max rendering quality
Codec Audio AAC 44100hz (as source)
Any ideas ?

Because we stream at 60 fps and we have to convert all the materials we receive from our partners from the usual 29,97 to 60.
Thanks for your MVPaluable help.
/sarcasm off

Audio goes out of sync when i open project on diff macs

i have an iMovie project created on an iMac saved to an external.
I go to open the project up on my macbook and the audio is out of sync.
I go back to my iMac with the same project and it works just fine.
I'm a bit confused because both macs use Mac OS X 10.6.4 and iMovie 8.0.6
what other differences might there be?
any input is appreciated as I'd love to work on projects while out in the field!

Try exporting the iMovie project as a single full quality dv format quicktime file.
I use iMovie6 HD and this is my usual procedure that works well.
Make the movie in iMovie, will involve many separate clips. When finished, export (share) as a single full quality dv format quick time file. When I have an hours worth of smaller projects, I create a new iMovie project and import all of the quicktime .dv files for each separate short project. I add chapter markers in this project, then share with iDVD. I then burn an hours worth of stuff at best quality and distribute to family and friends.
iDVD seems to work better with iMovie source that has fewer clips.
BTW: Are you having problems with standard def or hi def iMovie source. Another part of my procedure is that I take the raw tapes and download the entire thing into one iMovie project. I don't edit or change the footage at all, just want to archive to DVD for posterity. In this case, I want to share the iMovie project with iDVD directly. This has worked OK for standard def projects, but my first hi def project (1080i) that I tried, the sound was out of sync. To fix this, I had to create a regular DV widescreen iMovie project, and drag all the clips into it from the HD project. It took over an hour for my humble mac mini to convert the files, but I was then able to share with iDVD and the finished DVD worked ok.
Hope this helps.

When I use media manager to upres clip audio goes out of sync

I captured a clip and put it in DVNTSC 48kHz timeline at OfflineRT NTSC (Photo JPEG) then used the media manager to create a new sequence at full DV NTSC 48kHz res. I choose "Create offline", "set sequences to DV NTSC 48 kHz", and check all the boxes. I save a new project, open the new timeline and recapture the clip. The video looks great--it recaptures in full DVNTSC 48kHz res. But the audio is out of sync (by about 28 frames it looks like). What am I doing wrong? (This is the first time I'm trying this offline-then-online-process.) thanks.

Try exporting the iMovie project as a single full quality dv format quicktime file.
I use iMovie6 HD and this is my usual procedure that works well.
Make the movie in iMovie, will involve many separate clips. When finished, export (share) as a single full quality dv format quick time file. When I have an hours worth of smaller projects, I create a new iMovie project and import all of the quicktime .dv files for each separate short project. I add chapter markers in this project, then share with iDVD. I then burn an hours worth of stuff at best quality and distribute to family and friends.
iDVD seems to work better with iMovie source that has fewer clips.
BTW: Are you having problems with standard def or hi def iMovie source. Another part of my procedure is that I take the raw tapes and download the entire thing into one iMovie project. I don't edit or change the footage at all, just want to archive to DVD for posterity. In this case, I want to share the iMovie project with iDVD directly. This has worked OK for standard def projects, but my first hi def project (1080i) that I tried, the sound was out of sync. To fix this, I had to create a regular DV widescreen iMovie project, and drag all the clips into it from the HD project. It took over an hour for my humble mac mini to convert the files, but I was then able to share with iDVD and the finished DVD worked ok.
Hope this helps.

Audio going out randomly through front & rear jack during VLC & Mplayer

Similar Messages

Maybe you are looking for