Audio Hardware not supported by IDT Drivers

Hi,
I accidentally uninstalled my IDT Audio Drivers. Now my audio does not work at all. When I go to install the drivers suggested by the HP Software Support section, the drivers display this message during installation: "The hardware detected is not supported by this IDT software package. The install will be aborted."
HP Pavilion g6 - 1a21ca Notebook PC
Product Number: LV993UA
Windows 7 (64-bit)

Hi,
The first option I'd suggest trying is to run Windows System Restore.
If you have Norton Internet Security installed, you will need to disable Norton Tamper Protection as shown on the link below.
Norton Tamper Protection.
Once you've done this, shut down the notebook. Windows System Restore is usually best run in Safe Mode. Tap away at f8 as you start the notebook to enter Windows Recovery Console. Use the arrow keys to select Safe Mode and hit enter. When this has loaded, from the Start Menu, click All Programs, click Accessories, click System Tools and launch System Restore. Pick a restore point at least 24 hours before the original audio driver was deleted and then proceed with the restore process. When complete, Windows will reboot as normal.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Similar Messages

3750-E - hardware not supported by firmware

Hello, I have got new 3750 e-series which has universal image installed on it. I need to put this switch in stackwise with non-e-series 3750. The problem is that non-e-series are running IP BASE IOS and I wanted to put the same IOS on 3750 e-series. But it gives me the following message when I try to boot the switch with c3750-ipbase-mz.122-35.SE5.bin image.
Error: hardware not supported by firmware.
       Try loading newer software instead.
       System Resetting...
Thank you!

Hello, I have got new 3750
e-series which has universal image installed on it. I need to put this
switch in stackwise with non-e-series 3750. The problem is that
non-e-series are running IP BASE IOS and I wanted to put the same IOS
on 3750 e-series. But it gives me the following message when I try to
boot the switch with c3750-ipbase-mz.122-35.SE5.bin image.
Error: hardware not supported by firmware.
       Try loading newer software instead.
       System Resetting...
Thank you!
Hi,
Catalyst 3750-E switches running Cisco IOS Release 12.2(35)SE2 are compatible with Catalyst*3750 switches and Cisco EtherSwitch service modules running Cisco IOS Release*12.2(35)SE. Catalyst 3750-E switches, Catalyst 3750 switches, and Cisco EtherSwitch service modules can be in the same switch stack. In this switch stack, we recommend that the Catalyst*3750-E switch be the stack master.
Check out the below link for more information
http://www.cisco.com/en/US/docs/switches/lan/catalyst3750e_3560e/software/release/12.2_35_se2/release/notes/OL9778.html
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

Audio file not support

Hi,
I am using a folio overlays for a digital publication and insert audio files. While inserting the audio file not supported. The following error was occurred. Please advice.

I've moved your question to the DPS forum.

Stereo Mix Audio format not supported?

Hi
I'm pretty new at streaming, and i need help with my audio setup, I'm selecting Stereo Mix from the dropdown menu in the FMLE 3.2 but when i do it says.
"Audio format not supported."
"Audio format provided by audio capture device is not supported by this application."
I don't really understand why, since my mic device is supported. Why does this occur?
And how can I fix it?
I have a motherboard soundcard "VIA HD".
EDIT: I figured out why it doesn't work.
I went to the Recording devices menu to check the options but I noticed that Stereo Mix was "Currently unavailable" I figured maybe a program was using it but I don't know how to check what programs use the device.

I have noticed something else which is weird : the recording device is ALWAYS called "Line 1".
I tried renaming both the VAC playback and record devices Line 1 to other names, FMLE still displays "Line 1". This makes no sense (and Audacity sure doesn't behave that way, I have checked).
Should I need to make a complete uninstallation to wipe old FMLE settings ?

N900 Cannot play media - Audio Codec not supported

I'm trying to play a radio station on the N900 internet radio but I get the message that the media cannot be played, audio codec not supported. I was able to play the same station on my old N96 and other stations work on the N900.
Is there something I need to download to sort this out?
N96 v11.018

Sever wrote:
conveniently, im pretty sure the one youre referring to is called 'extra decoders support'.
And here is the link...
http://maemo.org/downloads/product/Maemo5/decoders-support/
If you found this post helpful, please click on the green "Kudos!" star. Cheers!

PPCG4 hardware not supported

I've got a PPCG4 FW800 1.25GHz DP & 1.25GB RAM OSX 10.4.6 and ProKit 3.1 framework. When I try to launch Aperture 1.0 it tells me that my hardware isn't supported and quits.
The specs state that the app supports "1.25GHz or faster PowerPC G4 processor"
Any ideas appreciated?
PPC G4 FW800 1.25GHz DP 1.25GB RAM ATI Radeon 9000 Pro Mac OS X (10.4.6)

Correct, the machine is not adequate. IMO Apple's use of the term "unsupported by Aperture" is unfortunate, because the semantic implication is that Aperture does not "support" a particular box. As a consequence dozens of folks have posted wanting to know when Aperture will be modified to "support" their boxes; as if the engineers just need to write some code to facilitate each hardware configuration (like printer drivers; or enablers that fit the OS to specific boxes).
IMO it would be more clear if Apple just identified boxes like yours (and my tower) as "this hardware is not powerful enough to run Aperture."
Although some speed improvements on the software side (both OS and app versions) can usually be made, the basic issue is that it takes strong hardware to drive heavy graphics applications. E.g. the best 2005 Powerbooks were the first time Photoshop was really usable on any Powerbook, and that just "adequate."
Aperture (designed to handle batches of hundreds of RAW image files) requires strong hardware including the CPU, RAM, hard drives, etc. (and especially the GPU, as noted). In the long term, app designers always take advantage of the stronger power of newer boxes, so we should plan - like Photoshop users have learned through 9 versions - on buying the high end of Macs at any given point in time if we want to have adequate throughput power to drive future versions of Aperture, Photoshop, etc.
Note that my expectation is that by 2007-2008 heavy graphics apps will be wanting more RAM and strong GPUs. Buyers of boxes limited to 2 GB max RAM and/or lesser graphics should expect performance to be limited accordingly. E.g. Photoshop CS2 boxes already perform best when configured with 6-8 GB RAM.
-Allen Wicks
Early 2005 1.67 GB G4 PB, Radeon 9700, 128 MB VRAM, 1.5 GB RAM Mac OS X (10.4.6) D2x, DP G4

Hardware not supporting old kernels!!

Yesterday I bought M/board Asus P5V800 + Intel LGA775 Pentium 4 CPU
http://www.asus.com/products4.aspx?l1=3 … odelmenu=1
Either the new CPU (socket LGA775) or the M/borad, doesn't support Kernel-2.6.11 (my custom kernel) but the latest 2.6.16. I also tried Archie Live CD (2.6.x) and Knoppix 3.6 (2.4.x), doesn't work. In Knoppix booting freezes asking for "south bridge dma", in Archie no X support, and in HD no X and LAN support.
In Windows, doesn't support Win 98. Runs but cannot install some of the board sources. Drive install CD for 2000 and XP only.
<b>For my information, is this a common restriction of LGA775?</b>
Note: End of the day I sold the hardwares and upgraded my old Celeron (socket 478) to Pentium. Pentium 4 with Celeron doesn't work well managing heavy multitask work. Compiling apps and at the same running X apps freezing the machine.

Windows has shoddy driver support until 2000/XP. I also found this out first hand trying to install Windows ME with what should be considered very old compatible drivers. That's we me pops runs latest standard kernel with Arch Linux now. It loves the hardware (not literally), but me pops loves the Arch.
So, it goes, backwards compatible is easy, forward compatible depends on too many things like driver unification and just how shoddy the OS is (MS). I'm just amazed at how much of a mule the OS can be when it has trouble recognizing hardware. so I had this thread: "I would rather spend a week causually installing/configuring arch than the rest of my life installing Windows ME."...or something to that effect.

Bluetooth Headset Hardware not supported

I have a Kensington USB dongle and I pasted the ASP info below. I can use it for pretty much everything except for using my headset. Does any one know of a way to enable this?
I can't imagine why Apple would only support headsets on their bluetooth hardware. I read in this forum that a D-link dongle is supported, does it have any specific features that my Kensington dongle does not list in the Apple system profiler?
Apple Bluetooth Software Version: 1.7.8f2
Hardware Settings:
tower:
Address: 00-0c-55-f8-47-c6
Manufacturer: Broadcom
Firmware Version: 2.0 (2.26981)
Bluetooth Power: On
Discoverable: Yes
HCI Version: 2 ($2)
HCI Revision: 0 ($0)
LMP Version: 2 ($2)
LMP Subversion: 26981 ($6965)
Device Type (Major): Computer
Device Type (Complete): Desktop Computer
Composite Class Of Device: 1057028 ($102104)
Device Class (Major): 1 ($1)
Device Class (Minor): 1 ($1)
Service Class: 129 ($81)
Requires Authentication: No
Services:
Bluetooth File Transfer:
Folder other devices can browse: ~/Public
Requires Authentication: No
State: Enabled
Bluetooth File Exchange:
Folder for accepted items: ~/Documents
Requires Authentication: Yes
When other items are accepted: Ask
When PIM items are accepted: Ask
When receiving items: Prompt for each file
State: Enabled
Devices (Paired, Favorites, etc):
Name:
Address: 00-15-b9-8b-d6-57
Type: Cellular Phone
Services: HFP Gateway, Dialup Networking, Object Exchange, File Transfer, WBTEXT, HSP Gateway
Paired: Yes
Favorite: Yes
Connected: No
Incoming Serial Ports:
Serial Port 1:
Name: Bluetooth-PDA-Sync
RFCOMM Channel: 3
Requires Authentication: Yes
Serial Port 2:
Name: SerialPort-1
RFCOMM Channel: 1
Requires Authentication: Yes
Outgoing Serial Ports:
Serial Port 1:
Address: 00-15-B9-8B-D6-57
Name: Bluetooth-Modem
RFCOMM Channel: 4
Requires Authentication: No
Serial Port 2:
Address: 00-15-B9-8B-D6-57
Name: SPH-A900-DialupNetworki-1
RFCOMM Channel: 4
Requires Authentication: No

Dlink is STILL the only officially supported usb BT dongle and I have one and it works great if you only want 10m radius.
I bought a Targus ACB20 (also known as ACB20us) because my GF wanted BT connectivity for her headset on her eMac. I realised AFTER that headsets were not supported for the Broadcom Chipset in this device.
I found the answer here -> http://cbri.umn.edu/~kunau/?p=18
this guy found a belkin patch for his device that allows broadcom chipset dongles to use headsets (YAY).
here is the direct dl link for the file -> http://ccgb.umn.edu/~kunau/wp-content/uploads/2006/06/BelkinF8T012v-OSXdriver.zip
This works fine with my targus dongle and another Anycom one I have (both 100m).
Hope this works for you.
Kez

All songs disappeared - audio format not supported by ipod

I went to sync my Nano today and instead ALL of the music was removed from it. Says can not sync music because audio format is not supported by iPod. We uninstalled itunes, restored the device and started again from scratch. The music synced fine, I bought an album on iTunes and when it synced ALL of the music was removed again and I got the same error for EVERY single song I tried to sync. Help?

That's very unusual and I have heard of such behavior. Since it seems to be an issue with iTunes, remove it and all other Apple software using the instructions in this Apple support document and install it from scratch.
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
Can you think of what may have changed since the last time the iPod successfully connected and synced with iTunes without any errors?
B-rock

MP4A audio files not support

I download audio lectures from the Stanford.edu web site via iTunes. All appear to be in a MP4A file format and are successfully downloaded to my PC (Windows XP), and transferred to my ZEN 8GB. However, when playing some, but not all, give me a? message: "Audio format is not supported."? Why? And is there any fix?

There are various types of m4a or aac files.
Also different encoders follow different standards...for instance only the most recent nero aac encoder seams to encode m4a files that work with the zen x-fi (most likely the zen also)
iTunes should work also.
m4a files intended for streaming audio seem to not work also.
If the file plays in itunes, try and convert it to mp3.
If you want more information, post what the audio properties are for the file (bit rate, encoding methods...etc)

Siri audio accent not supported in India in 4s, is there any update from apple regarding Siri ???

I am using apple 4s, but it not supporting Indian accent.
Is any other way out or update available from apple???

Siri is still beta.
Apple has not announced yet when updates to Siri will happen.

Iphone 3s hardware not supported by Windows xp

I plugged in my wife's iphone 3gs phone to update in Itunes. I got a message from Windows that the hardware driver was not recognized. I was able to get in Itunes and record my device. It started updating. I came back to an error message and now Windows refuses to recognize the iphone when I plug it in and Itunes will not pull up my phone as a recognized device either. I see the iphone in backup but cannot restore it. All my phone shows is a picture of the USB cord to connect to Itunes. How do I get Windows XP to accept the Iphone hardware? Please help me restore this iphone. Thank you,

Remove and reinstall iTunes. See: http://support.apple.com/kb/HT1925
Disable your antivirus and firewall before updating or restoring the phone.

Satellite P100: Conexant audio is not supported on Windows Vista 64bit

Last week I install the new system as Windows Vista 64bit but no sound. I think that was the problem with the 64bit audio driver. Is that anyone has the new driver for vista 64bit?

It seems some devices are not recognized by Vista common drivers which were shipped together with the Vista OS and therefore new drivers are needed. But because the Vista is not official on the market (official start is end of January 2007) the drivers are not published.
But where did you get the 64bit Vista version???

Hardware not Supporting Premiere Pro CS5.5 (and after effects)

Hardware: 1st generation Macbook Pro 2.0Ghz Intel Core Duo processor, 2g (maximum ) ram, 500gb hybrid SSD/7200 hard drive. Mac OS leaopard 6.6
I bought the master collection recently which includes premiere and after effects CS5.5. Pre sales I was advised by adobe that ALL macbook pros will run all these products (by an adobe customer services Advisor)
I can't load them because (as I have now learnt) that the core duo processor only supports 32 bit- I phoned technical support, many times since 15th July and was repeatedly told that ALL macbook pros can run them, it was just a case of changing my OS to 64 bit. Apple are clear that this is not the case.
Eventually I was referred to a tier 2 advisor, who asked me which processor type, and finally said it is clear that I need earlier versions to run on this and I would be contacted by email to provide a earlier 32 bit version of these 2 programs (as is supplied to windows 32 bit users). This was 2 weeks ago and I have had no response, I have phoned several times and some advisors try to start the whole process again and insisting that I should be able to install these.
Today an advisor has told me that they have checked the notes and the tier 2 advisor has advised I "need to upgrade my hardware" (ie buy a new mac !!!)
No-one will give me any phone numbers of a tier 2 advisor to discuss this or complain about it. Nor an email address.
First i want to request that adobe, having misled me, should give me earlier copies. Especially as this has already been agreed. Secondly I want to complain about the huge amount of time wasted and how I have been fobbed off.
Apologies if this is not the exact forum space for it but I cannot find the issue on FAQ so I would be very grateful if anyone can put me in touch with the right person, or if any of the moderators would know.
Michael Bannon

8/17/11
Case #0182568779: case update: 0206296078
Withdrawn
8/16/11
Case #0206296078: Download Link
Withdrawn
8/2/11
Case #0182523822: Unable to install After effects
Withdrawn
8/2/11
Case #0182527143: Escalated case :182523822, 0206296078
Withdrawn
8/1/11
Case #0182524205: installation issue
Withdrawn
Many thanks: these were the case numbers- these have all bee witthdrawn despite the fact none of them has yet provided the solution promised by the tier 2 advisor.
Michael

Graphics Hardware Not Supported

Just installed CS6 and wish to use the 3d option to create some text. However I get the window popup telling me that my graphics hardware is not officially supported for 3D.
I have a Nvidia GTX Titan which has 6gb vram.

mchief111
Could you please post your system info listed in Photoshop's Help > System Info dialog box?
Click Copy, then paste it in a response here.
That will help us determine further what's going on.
Allow me echo the interest in making sure the latest nvidia driver is applied
http://www.nvidia.com/Download/indexsg.aspx?lang=en-us
Your video card: NVS (notebooks) -> NVS 4200M
Also give the forcing Photoshop.exe to use the nVidia video card in the NVIDIA Control Panel
Right click desktop -> NVIDIA Control Panel
Manage 3d Settings category -> Program Settings tab
under the 1. "Select a program to customize" drop down menu: select Photoshop.exe
for 2. Select the preferred graphics processor for this program: select High-performance NVIDIA processor
Click the Apply button that appears in the lower right.
You will need to reset Photoshop's preferences as well for it to look for your video driver changes.
To do this, immediately after starting Photoshop.exe press and hold Ctrl+Shift+Alt
Click Yes to reset the Photohsop Settings file.
Let us know how it goes from there.

Audio Hardware not supported by IDT Drivers

Similar Messages

Maybe you are looking for