Audio Help Needed - Dual G5 1.8
I need a little help. I have a set of speakers plugged into the rear audio port of my G5, and they work great. However, when I also plug a set of headphones into the audio jack on the front panel, I would like the speakers to be disabled. Is there any way to do this?
-AstraPoint
The fourth post here may help (or not) -
http://discussions.apple.com/thread.jspa?messageID=604731򓨻
Similar Messages
-
I am running FCP 5 on a MacBook Pro, and I am having a couple of audio issues that I can't figure out. The first is:
I am capturing mini DV from a camcorder via firewire. Audio is being captured, and the input levels are moving, but I can't hear it while capturing. The setup says that the speaker is off. How do I turn it on? I can't seem to find it anywhere.
Problem two: The audio on the tape is stereo, but it is being captured as 2 channel mono. In my capture settings, I have no audio options. They are all greyed out. How do I change them to stereo? Any help would be appreciated.
Thanks, Charles
mac book pro Mac OS X (10.4.7)if you are capturing DV then you can "Preview" the audio from tape during Log and Capture by going to the Capture Settings tab in the Log and Capture window and enabling the Audio --> Preview checkbox
if you are capturing HDV then this is not an option, you need to connect speakers instead to the camera/deck and preview from source.
problem two: again, check the Log and Capture window > Capture Settings tab.
there is a button to the left of the input channel meters ... you can toggle between stereo and dual mono when you press this button. if the picture on the button shows two interlocking circles then it is set to capture the two channels as a stereo pair, if the two circles are separate then it is set to capture the two channels as dual mono
hope it helps
Andy -
URGENT AUDIO HELP NEEDED!! Suitable audio filters
I'm in desperate need of knowing what audio filters are good to reduce background noise for a film I'm making. I've got a basic DV camera that picked up a lot of wind the other day and I am trying to minimise the background noise so that I can pick up what people were saying.
Does anyone know what audio filters on Final Cut Express are suitable for doing this?
CheersI have never found a way to filter out wind noise, and I don't think it is practicable. I think that the problem is that the frequency in wind noise is similar to the frequencies in most video audio, so you can't filter out the wind noise without damaging the rest of the audio.
The only solution seems to be to shoot on a windless day, or use a very directional mike, and/or have a wind sock that is effective. (Unless soemone else knows a way.) -
I have a Steinberg MI4 and a Roland Fantom X7, and am trying to use my Fantom in Logic to record audio. Need help setting it all up using MIDI cables. Please help !
Encryption wouldn't matter except for Wifi.
While 10.2 might help, there's not much you can do on the Internet these days with less than 10.4.11
Tiger Requirements...
To use Mac OS X 10.4 Tiger, your Macintosh needs:
* A PowerPC G3, G4, or G5 processor
* Built-in FireWire
* At least 256 MB of RAM (I recommend 1GB minimum)
* DVD drive (DVD-ROM), Combo (CD-RW/DVD-ROM) or SuperDrive (DVD-R) for installation
* At least 3 GB of free disk space; 4 GB if you install the XCode 2 Developer Tools (I recommend 20GB minimum)
http://support.apple.com/kb/HT1514
http://www.ebay.com/sch/i.html?_nkw=mac+os+x+tiger+retail+10.4
See Tom's, (Texas Mac Man), great info on where/how to find/get Tiger...
https://discussions.apple.com/message/15305521#15305521
Or Ali Brown's great info on where/how to find/get Tiger...
http://discussions.apple.com/thread.jspa?messageID=10381710#10381710
As far as Memory, that's sort of easy, find your eMac here...
http://eshop.macsales.com/MyOWC/Models.cfm?Family=emac&sType=Memory
As far as Hard Drive, it's not easy to replace the Internal drive, I'd maybe suggest an external Firewire drive to boot from...
http://eshop.macsales.com/item/Other%20World%20Computing/MAU4S7500G16/ -
Need Audio Help - USB External Speakers
This should be fun!
Need Audio Help! My USB external speakers are recognized in Garage Band Preferences, but NOT in System Preferences. (I use the audio interface, US-144 Tascam)
Which means:
I can only play my speakers using Garage band and not iTunes.
They were working in both iTunes and GB many times before.
I see that others have had problems losing their external speakers after updating their iMac.
I've called Apple for assistance (no help)
Changed the order of connections
I've shut down again, again...
Help pleaseOpen System Preferences/Sound and select the USB Speakers as your Output device
If that doesn't do as you expect, or you need to tweak them, run Utilities/Audio MIDI Setup and select them there then adjust the Format and Volume etc. -
HELP NEEDED WITH ADDAPTER-DVI TO VGA.
PLEASE ...HELP NEEDED WITH WIRING CROSS OVER....CAN YOU HELP WITH BACK OF PLUG CONNECTIONS...I SORTA UNDERSTAND THE PINOUTS BUT CANT MAKE AN EXACT MACH...WOULD LIKE TO BE 100% SURE...
......THIS ENSURES NO SMOKE!!!
THE CARD IS AN ATI RADEON RX9250-DUAL HEAD-.........ADDAPTER IS DVI(ANALOG)MALE TO VGA(ANALOG)FEMALE.
ANY HELP VERY MUCH APPRECIATED........ SEEMS YOU NEED TO BE ROCKET SCI TO ATTACH A BLOODY PICTURE...SO THIS HAS BEEN BIG WASTE OF FING TIME!Quote from: BOBHIGH on 17-December-05, 09:21:31
Get over it mate !
I find it easy t read CAPS...and if you dont like it ...DONT READ IT!
And why bother to reply...some people have nothing better to do.
Yes there chep and easy to come by...Ive already got a new one.
All I wanted was to make a diagram of whats inside the bloody thing...it was a simple question and required a simple answer.
NO NEED TO A WANKA !!
I feel a bann comming up.
Have you tryed Google ? really.. your question is inrelevant. No need to reply indeed.
Why do you come here asking this question anyway ? is it becouse you have a MSI gfx card ? and the adapter has nothing to do with this ?
You think you can come in here yelling.. thinking we have to put up with it and accept your style of posting. This is not a MSI tech center.. it's a user to user center.. Your question has nothing to do with MSI relavant things anyway's.
Google = your friend.
Quote from: BOBHIGH on 17-December-05, 09:21:31
it was a simple question and required a simple answer
Simple for who ? you (buying a new one) ? me ? we ? .really...........
Quote from: Dynamike on 16-December-05, 04:11:48
1: There are allot of diffrent types of those adapters.
If any of the mods have a problem about my reply.. please pm me. -
Help needed with Vista 64 Ultimate
"Help needed with Vista 64 UltimateI I need some help in getting XFI Dolby digital to work
Okay so i went out and I bought a yamaha 630BL reciever, a digital coaxial s/pdif, and a 3.5mm phono plug to fit perfectly to my XFI Extreme Music
-The audio plays fine and reports as a PCM stream when I play it normally, but I can't get dolby digital or DTS to enable for some reason eventhough I bought the DDL & DTS Connect Pack for $4.72
When I click dolby digital li've in DDL it jumps back up to off and has this [The operation was unsuccessful. Please try again or reinstall the application].
Message Edited by Fuzion64 on 03-06-2009 05:33 AMS/PDIF I/O was enabled under speakers in control panel/sound, but S/PDIF Out function was totally disabled
once I set this to enabled Dolby and DTS went acti've.
I also have a question on 5. and Vista 64
-When I game I normally use headphones in game mode or 2. with my headphones, the reason for this is if I set it on 5. I get sounds coming out of all of the wrong channels.
Now when I watch movies or listen to music I switch to 5. sound in entertainment mode, but to make this work properly I have to open CMSS-3D. I then change it from xpand to stereo and put the slider at even center for 50%. If I use the default xpand mode the audio is way off coming out of all of the wrong channels.
How do I make 5. render properly on vistaWe ended up getting iTunes cleanly uninstalled and were able to re-install without issue. All is now mostly well.
Peace... -
ONKYO TX-SR805 Set-up Menu HELP Needed
This is a LONG post, but I would appreciate if you would read it and respond to it. The settings That are setup might not be the CORRECT settings. If you think a different setting should be made, please let me know.
Also right now I only have 2 front speakers (NHT VT-1A), 1 middle( NHT VT-1C), and a NHT SW12 Subwoofer. I will be hooking up 2 or 4 more speakers for the REAR.
Here are the settings on my TX-SR805 receiver on the set-up menu. I could use some help to see if they need set to something else.
2.2 Speaker Config
Subwoofer yes
Front 70Hz
Center 90Hz
LPF of LFE 80Hz THX
2.6 THX Audio Setup
THX subwoofer YES I don't know if mine is or not
BGC OFF Not sure what this BGC means
3. AUDIO ADJUST
3.1 Tone Control
Front Bass -1dB
Treble +1dB
Center Base +2dB
Treble +7db
Subwoofer Base +7
3.2 DIRECT
Delay Enable
DSD NO Not sure what DSD is
3.3 MULTIPLEX/MONO
Multiplex
Input CH Main/Sub
Mono
Input CH L+R
Output Speaker L/R
3.4 PLIIx/Neo:6
PLIIx Music (2ch input)
Panorama ON
Dimension +1
Center Width 3
Neo: 6 Music
Center Image 5
3.5 DOLBY EX
Dolby EX AUTO
3.6 THEATER-DIMENSIONAL
Listening Angle Narrow
3.7 LFE LEVEL
Dolby Digital -10dB
DTS -10dB
Multich PCM -10dB
Dolby True HD -10dB
DTS-HD Master Audio -10dB
DSD -10dB
4. SOURCE SETUP
CABLE/SAT
4.1 INTELLIVOLUME +4Db
.2 A/V SYNC 0 msec
.3 NAME EDIT Blank
5. LISTENING MODE PRESET
5.1 DVD
Analog/PCM NOT SURE WHAT TO SET HERE
Dolby Digital NOT SURE WHAT TO PUT HERE
NOT SURE WHAT TO PUT FOR ANY OF THESE LISTENING MODE PRESET
5.8 TUNER (ANALOG) Neural THX 5.1 is set on mine. Is this correct?
CD ?
6. MISCELLANEOUS
6. 1 VOLUME SETUP
Volume Display Relative
Muting Level -40dB
Maximum Volume +10dB
Power on Volume -22dB
Headphone Level +2dB
6.2 OSD SETUP
Immediate Display OFF
Monitor Type 16:9
Display Position TOP
7. HARDWARE SETUP
7.4 ANALOG MULTICH
Subwoofer Input Sensitivity 0
7.5 HDMI
ALL under here are ENABLE
Solved!
Go to Solution.I gave you some answers in your original post. I wish you didn't start a new one. Here is what I posted.
Re: ONKYO TX-SR805 Set-up HELP Needed[ New ]
Options
Mark as New
Bookmark
Subscribe
Subscribe to RSS Feed
Highlight
Print
Email to a Friend
Report Inappropriate Content
01-21-2010 08:24 AM
Unfortunately this is very difficult because the top half of your post, your really the only one that can answer what the setup should be. The adjustments are made based on the acoustics of your room and how everything sounds noone can really give you info on it because every house, and room has different acoustics. The walls, insulation, carpet or bare floors, basement or main floor are just some examples of what can make a difference in sound reproduction. By the way NHT (Now Hear This) are excellent speakers. For bass and treble, the music I listen too requires a high treble content so I usually have it at 7 out of 10 but my bass is at 4 out of 10. The sub base should be fine where it is.
Did your receiver come with an Audessy mic for calibration. I would use that for a basic setup and go from there I am not sure if on your unit it will do frequecy but I think it did.
Your volume settings look fine again personal preference there is right or wrong.
For you listening mode Preset you should have an auto setting I am at work so it may take a coule of hours for me to get back to you as I have to go through your manual and see what you would set it up with so please bare with me. I will list the info as I read it so it may not be in the order you have it.
I will have to make a second post since I can't go back and edit this one. -
I have hopped around on different distros and I found that Archlinux would be the best solution for me. However, I need help with dual booting Archlinux and Vista as I will need Vista around for one program and a game that do not work with any Linux distro that I have tried. I have not done a text based install before, I have only used newbie distros but I want to move on to Archlinux.
I will only need one partition for Vista and one for Arch. I believe I can achieve the goal of dual booting them by shrinking the vista partition, and then installing Arch in the remaining space and use GRUB to boot the necessary partitions when my laptop is powered on. This works with Ubuntu, so I assume it shall be the same basic concept with Arch. I can follow the instructions on installing, and the installation is easier than I had expected it to be. I have one question, how would I go about using the above technique that I mentioned during the install? I would like to know how to do it correctly, I cannot risk messing up Vista. I'm fifteen and my dad would be very frustrated if I did mess up Vista. I would appreciate some specific instructions, because I really like Arch from what I have read. I also look forward to being an active member in the community as well if all goes well.Welcome!
Another young one I see! I'm currently 17, however I started using linux when I was 13 (8th grade year).
You can resize the vista partition by using gparted. You can download the gparted livecd from there website (http://gparted.sourceforge.net/download.php). I do not know specific directions, but it is pretty obvious how to resize, and if you need help you can probably google something like "resize partition gparted". I WARN YOU that you do risk data loss resizing the partition. I don't believe the risk is high, but it still there, so backup any important data that you may have in case something goes wrong!!
Do you have your own computer that you can experiment on? That might be a safe option than using your dads. I am been fortunate to have hand-me-down systems, but when I was young I made my dad angry quite a few times "experimenting!"
If your dad's system has enough juice, you may want to consider install arch in a virtual machine to get idea of however thing works. Following the Beginners Guide on the wiki will be you best bet for a successful and well configured machine (http://wiki.archlinux.org/index.php/Beginners_Guide). If you really want to play it safe you can even go as far as install windows in a virtual machine, resizing the partition, and installing arch in the same virtual machine.
I hate to say this, but if you absolutely can not mess up vista, I would advice against installing any other OS and messing with the partition scheme. As whenever you mess with the partitions you run a risk of messing up Vista (or any other os for that matter). If you don't already have your own computer which you can tinker with, it might not be a bad idea to look at getting one. They are becoming cheap, you can build one for about $300-$400USD, or buy one for probably around $400.
Hope this helps a bit... -
USB Audio Driver need in Digital Audio playback of iPOD in IUI Mode
In iPOD User Interface Mode for playing the Digital Audio from iPOD using USB, does the complete USB Audio Driver needs to be created or is it enough to set the sampling frequency of the USB ISO endpoint.
Hi! Did you ever find a solution for this problem? Bought an SB Li've! External just yesterday and on a clean install (Windows XP SP2) I'm having the exact same problem.
Edit: By switching the USB port from 2.0 (Hi-Speed) to "normal" (USB .x) in the bios I got rid of this problem! Hope this might be of some help to anyone!Message Edited by yuzz on -04-200706:37 PM -
recording help needed. I'm a beginner, imac, logic express and helix board 12 firewire.
I have recorded my daughter voice only ok, BUT when i import audio file to track 1 as backing track and my daughter is using headphones from the helixboard to sing to she does not record to track 2 when all in enabled.
Should her headphone come from the imac and not the helix board
Regards
PaulCheck the recording channel in the channel strip.
It must be set the same as the audio interface channel.
cheers
rob -
Troubleshooting help needed: My iMac keeps crashing and restarting with a notice: "Spinlock application timed out" What can I do?
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the page that opens.
Select the most recent panic log under System Diagnostic Reports. Post the contents — the text, please, not a screenshot. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post shutdownStall, spin, or hang reports. -
help needed for writing query
i have the following tables(with data) as mentioned below
FK*-foregin key (SUBJECTS)
FK**-foregin key (COMBINATION)
1)SUBJECTS(table name)
SUB_ID(NUMBER) SUB_CODE(VARCHAR2) SUB_NAME (VARCHAR2)
2 02 Computer Science
3 03 Physics
4 04 Chemistry
5 05 Mathematics
7 07 Commerce
8 08 Computer Applications
9 09 Biology
2)COMBINATION
COMB_ID(NUMBER) COMB_NAME(VARCHAR2) SUB_ID1(NUMBER(FK*)) SUB_ID2(NUMBER(FK*)) SUB_ID3(NUMBER(FK*)) SUBJ_ID4(NUMBER(FK*))
383 S1 9 4 2 3
384 S2 4 2 5 3
---------I actually designed the ABOVE table also like this
3) a)COMBINATION
COMB_ID(NUMBER) COMB_NAME(VARCHAR2)
383 S1
384 S2
b)COMBINATION_DET
COMBDET_ID(NUMBER) COMB_ID(FK**) SUB_ID(FK*)
1 383 9
2 383 4
3 383 2
4 383 3
5 384 4
6 384 2
7 384 5
8 384 3
Business rule: a combination consists of a maximum of 4 subjects (must contain)
and the user is less relevant to a COMB_NAME(name of combinations) but user need
the subjects contained in combinations
i need the following output
COMB_ID COMB_NAME SUBJECT1 SUBJECT2 SUBJECT3 SUBJECT4
383 S1 Biology Chemistry Computer Science Physics
384 S2 Chemistry Computer Science Mathematics Physics
or even this is enough(what i actually needed)
COMB_ID subjects
383 Biology,Chemistry,Computer Science,Physics
384 Chemistry,Computer Science,Mathematics,Physics
you can use any of the COMBINATION table(either (2) or (3))
and i want to know
1)which design is good in this case
(i think SUB_ID1,SUB_ID2,SUB_ID3,SUB_ID4 is not a
good method to link with same table but if 4 subjects only(and must) comes
detail table is not neccessary )
now i am achieving the result by program-coding in C# after getting the rows from oracle
i am using oracle 9i (also ODP.NET)
i want to know how can i get the result in the stored procedure itsef.
2)how it could be designed in any other way.
any help/suggestion is welcome
thanks for your time --PradeeshWell I forgot the table-alias, here now with:
SELECT C.COMB_ID
, C.COMB_NAME
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID1) AS SUBJECT_NAME1
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID2) AS SUBJECT_NAME2
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID3) AS SUBJECT_NAME3
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID4) AS SUBJECT_NAME4
FROM COMBINATION C;
As you need exactly 4 subjects, the columns-solution is just fine I would say. -
Help needed I have a canon 40D. I am thinking of buying a canon 6D.But not sure that my len
Hi all help needed I have a canon 40D. I am thinking of buying a canon 6D.
But not sure that my lenses will work.
I have a 170mm/ 500mm APO Sigma.
A 10/20 ex Sigma HSM IF.
And a 180 APO Sigma Macro or do I have to scrap them and buy others.
ALL Help will be greatly received. Yours BRODIEIn short, I love it. I was going to buy the 5DMark III. After playing with it for a while at my local Fry's store where they put 5DMII, 5DMIII and 6D next to each other, using the same 24-105L lens, I decided to get the 6D and pocket the different for lens later.
I'm upgrading from the 30D. So I think you'll love it. It's a great camera. I have used 5DMII extensively before (borrowing from a close friend).
Funny thing is at first I don't really care about the GPS and Wifi much. I thought they're just marketing-gimmick. But once you have it, it is actually really fun and helpful. For example, I can place the 6D on a long "monopod", then use the app on the phone to control the camera to get some unique perspective on some scenes. It's fun and great. GPS is also nice for travel guy like me.
Weekend Travelers Blog | Eastern Sierra Fall Color Guide -
Help needed! Raid degraded again!
Hi!
Help needed! I hava made bootable RAID with two S-ATAII 250Gb HDD and its not working! Every now and then at bootup I get a message RAID -> DEGRADED... Must be seventh time! Rebuild takes its own time!
What am I doing wrong!
T: Ekku
K8N Neo4 Ultra
AMD 64 4200+
2 Gb RAM
2 x 250 Gb HDD (Maxtor)
nVidia RAID (in mb)
P.S. I wery SORRY with my poor language!I'm going to blame the nVRAID because I've seen issues with it in the past. If your motherboard has another non-nVidia RAID solution, use that instead. Using the nVidia SATA ports as BASE or JBOD is fine and dandy but RAIDing always had issues. It's not even a driver issue I think it's just instability. Latest drivers and even boxed drivers never helped. Granted, some will report success with their rig. But on a professional level I've seen nForce issues on different motherboards and different hard drives that had RAID disaster stories.
Good luck and if you don't have another RAID solution, my suggestion would be to buy a dedicated RAID controller card.
LPB
Maybe you are looking for
-
I have a mac book pro and am using Maverics. I saw that there was a system update so I updated and once I did I noticed a few weird things happening. The tabsacross my browser didn't have little x's to close them I neede to right click to close the t
-
How to get log information from database server?
Oracle 9.2 in Unix we got blocking error in the production database last midnight for 40 min and nothing was being processed during that time which delayed our production night batch process. Then it was gone after 40min. I like to know what was happ
-
How to check TimerTask's task is finish??
Hi, I have two timerTask schedule in two different classes. 1 is every 10sec grab something from database the second 1 is every one hour stop the first schedule and do something then restart the first schedule. My question here is how am i going to k
-
REMOVING IPSEC VPN CONFIG FROM PIX 6.3 FIREWALL
Hey, we have pix 6.3 serving as internet firewall and we are int process of replacing it with new ASA Device. currently there are several site to site and remote vpn are configured for access purposes. i tried to remove one site2site ipsec vpn from
-
FCP 7.0 upgrade problem recognizing serial number
I am upgrading from FCP 6.0.6 to 7.0 on my new MacBook Pro but I can't get the installation disc to recognize the serial number. If I enter an incorrect number it will immediately say so, but when I enter the correct number I just get the spinning wh