Audio Interface Errors after Upgrade

Hi Y'all. I'm a bit dense on audio ins and outs, so bear with me. I have a M-Audio Firewire Solo audio interface. It worked fine for the last 5 months or so on Logic Express 7. After Upgrading to Logic 8 yesterday, it now records all kinds of beeps and static that I can't get rid of. It sounds almost as if there is a loose cable somewhere, except that logically that isn't it, since the only thing that changed since I last used it is the upgrade. Anyone else have this sort of problem? Thoughts?

OK, so FYI, M-Audio Tech Support has (knock-on-wood) solved the problem. I unplugged the audio interface, installed the Apple 10.4.10 Combo Update from the Apple website (I had never heard of this combo update, but apparently it updates things that would not otherwise get updated even if your Software Update says you are up to date), then repaired permissions in Disk Utility, uninstalled the M-Audio driver, fixed permissions, reinstalled the M-Audio Driver, fixed permissions, shutdown, plugged the audio interface back in (without the power cord, only firewire - apparently this is very important, not that M-Audio ever tells you that until it breaks), rebooted and presto!
It seemed kind of ridiculous to me, but hey, it seems to be working.

Similar Messages

  • Time machine fails backing up with a "backup disk not found" error after upgrade to Lion 10.7.2

    Time machine fails backing up with a "backup disk not found" error after upgrade to Lion 10.7.2. I've erased and reformatted the drive; reconnected Time Machine(it saw it) and began a new backup. The backup starts again but fails before completing with backup drive not found error. I used the 10.7.2 combo update. Any help on how to fix this problem would be appreciated.

    Arghhhhhhhhhhhhhhhhhhh!!!!!!
    After waiting since October for a fix, I have now upgraded the firmware on the Time Capsule and installed the new Airport Utility, released yesterday, and the situation is even worse.
    Up until now, the Airport Utility had an option to disconnect all drives manually and the Time Capsule would then work until the next reboot – a temporary (?) work-around.
    Now that option does not exist in the new-look Airport Utility. And the Airport Utility installation can’t be rolled back and the old utility won’t restore.
    The sparesbundle is still not accessible. Anyone worked out a work-around in the new environment yet?
    I have another Time Machine backup working fine to a trusty old Lacie Drive so erased the one on my Time Capsule to see if that works. I have renamed the Capsule and the Time Capsule Drive.  But to build another full backup will take at least two days and I shall be away from tomorrow and am reluctant to leave the Capsule and computer up and running for a week. And I’ll bet the sparsbundle will still be nowhere to be found.
    How can Apple screw up so badly when they are to become the richest company in the entire world and – soon – will have more cash in the bank than the entire United States? Can’t they afford someone who really can sort this out? Especially when a Firewire connected hard drive – my trusty and simple LaCie – works fine.
    Words, almost, fail me.

  • Audio-interface unavailable after system update

    I use a Behringer FCA202 firewire audio-interface.
    After updating to 10.4.10 it is unavailable.
    Profiler tells me it is there, but I can not see it in either application nor in the sound-settings.
    Any help appreciated...

    If you run /Utilities/Audio MIDI Setup does it appear there ?
    Try unplugging all devices then reset Parameter RAM (hold apple/option/p/r keys at boot and don't let go until the third chime) then re-connect the Firewire cable.

  • Flash 9,0,124,0 security error after upgrade

    I get the following error after upgrading my Flash Player
    (after my system prompted me to install it while running the Flash
    editor):
    Internet Explorer has blocked this site from using an ActiveX
    control in an unsafe manner.
    I have uninstalled and reinstalled the player from the
    browser, about 5 times now and it continues to be a problem for IE.
    Works ok in Firefox if I manually download the FF installer. Is
    there a standalone installer for Vista/IE7 or am I forced to use
    the ActiveX installer which seems to have issues?

    Fix: Removed both (!?more than one?!) versions of flash
    player in my Programs and Features dialog, then ran
    uninstall_flash_player.exe, reset IE7 to factory spec, then
    reinstalled Flash from ActiveX. Seems to be working now.

  • TS1277 "iPhoto was unable to connect to Photo Stream" error after upgrading to mountain lion

    Has anyone gotten this error after upgrading to mountain lion on a computer that already had a user setup on it?
    My iphoto was working with photostream and now it will not connect at all.
    I ran fix disk permissions and once it showed up in iphoto, photostream was loading and then it disappeared again.
    help!

    FWIW I fixed mine when I realised I'd probably downloaded iPhoto using an AppleID from the App Store but logged into iCloud with a different AppleID. I deleted iPhoto and it's related files (but not the iPhoto Library) using CleanApp, entered the App Store with my usual AppleID and downloaded iPhoto again. Once the App Store, the downloaded iPhoto and iCloud logins were the same iPhoto Stream worked again.

  • Error after upgrade CRS 4.0.4SR1 to 4.0.5SR2

    Hi,
    I've got some errors after upgrading my CRS 4.0.4SR1 cluster to 4.0.5SR2.
    First my publisher's status stay in "patch" status for near 2 days now. I'm not able to change anything in the configuration, i've got this message "Config Changes are not allowed during 'Patch' operation, which was started by  '_ccbu_build' at 'Thu Apr 08 04:31:04 CEST 2010 '. Please try again after  'Patch' is complete."(ERREUR02.jpg). How can I change this status?
    Then I've got errors in historical DB which is working but not on the publisher only on subscriber. How can I resynchronize this DB?
    Thanks for your help.

    Thanks Tammy for the reply
    We already tried the suggested SAP Note couple of time without any luck.
    Regards,
    SJ

  • Error after upgrading from  sap b1 pl 35 to pl 49

    hello sap experts 
    iam getting the following error after upgrading from  sap b1 pl 35 to pl 49 this error is coming if we have given round off or discount in the below cell
    "Discount deviates from authorised ranges (sales oreder-discount%for document) [message 439-15] pls make it as soon as possible an i will be thankful to those guys .
    regards
    Jenny

    Hello Jenny,
    You may check by supreuser account first to see if you got the same error.  If not, it probably just related to user authorization.  If yes, it must be a bug.
    Thanks,
    Gordon

  • What can I do if I get an internal power error after upgrading to Windows 10?

    QuestionWhat can I do if I get an internal power error after upgrading to Windows 10?
    AnswerSome laptops with AMD graphics that upgraded to Windows 10 are showing blue screens with error messages regarding Internal_Power_Error. If you receive this error, try the procedure in this article.
    First, you'll need to quickly set the boot options to Safe Mode:
    1. Hold the Windows key and press 'R' to open the run box.
    2. Type MSCONFIG, then press ENTER.
    3. Select the BOOT tab.
    4. Under BOOT OPTIONS, check Safe boot, then select Minimal.
    5. Click Apply, then OK.
    6. Click Restart. (If prompted, click Restart anyway.)
    From Safe Mode disable the AMD Display Driver:
    1. Hold the Windows key and press the 'X' key to open a menu in the lower-left.
    2. Click Device Manager.
    3. Expand Display adapters to show the two display adapters.
    4. Double click AMD Radeon R9 M200X Series.
    5. Select the Driver tab.
    6. Click Disable, then click Yes to confirm.
    7. Click Close.
    8. Hold the Windows key and press the 'R' key to open the run box.
    9. Type MSCONFIG, then press ENTER.
    10. Select the BOOT tab.
    11. Uncheck Safe boot.
    12. Click Apply, then OK.
    13. Click Restart. (If prompted, click Restart anyway.)
    From Windows 10 started with the AMD Display Driver disabled:
    1. Hold the Windows key and press the 'X' key to open a menu in the lower-left.
    2. Click Device Manager.
    3. Expand Display adapters to show the two display adapters.
    4. Double click AMD Radeon R9 M200X Series.
    5. Select the Driver tab.
    6. Click Update Driver.
    7. Click Search automatically for updated driver software.
    8. An AMD driver should be found and installed.
    The driver that originally caused this problem is AMD display driver version 15.200.1046.2 dated 7/15/2015.
    The driver installed through this process might have an older date, such as 15.200.1055.0 dated 7/6/2015. That's okay.

    I'm having the same problem.  I got error message 21.  I went to apple store.  they are saying i have a hardware error.  Really, my phone was working before the update.  Asked me for $150 to get another one when I am due to get a new one and wanted to pass this one on to my child. 
    Help please,
    I will be glad to go back to the older software update

  • Imac error after upgrade to 10.8.4

    I received an error after upgrade tp brand new imac.  Error was upgrade was not installed.  Upon reboot the version of SW in About thi Mac is 10.8.4.  Bug?
    iMac i7, 21.5" 16GB memory, fusion drive.
    Thanks for input.  I assume the upgrade took.

    Verify Permissions gave me some errors, I deleted the repeats and the permissions fixed lines:
    Repairing permissions for “Macintosh HD”
    Warning: SUID file “System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/readconf ig” has been modified and will not be repaired.
    Warning: SUID file “usr/lib/sa/sadc” has been modified and will not be repaired.
    Warning: SUID file “usr/bin/quota” has been modified and will not be repaired.
    +++ (multiple repairs)
    Permissions repair complete
    I verfied the HD
    Much text (removed)...
    The volume Macintosh HD appears to be OK.
    I also loaded the Apple downloads version of the upgarde and received the following (again):
    The Installation failed
    The insatllation encountered an error that caused the installation to fail. Contact the software manufacturer for assistance.
    Message was edited by: Steve51K

  • No audio device installed after upgrading to windows 7???

    after upgrading to windows 7 audio is not working error audio device not install driver error...

    Hi,
    You will need to identify your CPU and chipset. CPU-z is a free and safe utility that can do that for you.
      If your system has an Intel chipset with disccrete or onboard graphics or an NVIDIA chipset with onboard graphics, then the drivers are here at this Realtek download page.
    If your notebook is an AMD CPU and NVIDIA chipset, with a discrete graphics module installed, then the driver for your Conexant CX20549-12 will be here.
    Post you results here in your thread so others rsearching for the same information can benefit from it. 
    Best regards,
    erico
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • ITunes error after upgrade to 7.1.1

    After upgrading to version 7.1.1, I receive the error message "iTunes cannot run because it has detected a problem with your audio configuration" whenever I attempt to start the program.
    iTunes ran fine before the upgrade. All other audio software programs are running fine. Thanks for any help...

    "iTunes cannot run because it has detected a problem with your audio configuration"
    that's typically caused by a problem with your QuickTime. (iTunes uses QuickTime for audio and video playback.)
    the following document may be of some help:
    iTunes 7 for Windows: iTunes had detected an audio configuration problem

  • Login Error after Upgrading from BW 3.5 to BI 7.0

    Hi Experts,
    We have carried out an upgrade from BW 3.5 to BI 7.0.
    After Upgrade we are not able to login using SAP GUI. we are getting an error saying..
    Username or Password not Valid..
    During the upgrade (in Netweaver 2004s ) is there procedure necessary to be followed, which we could have missed..
    Your response will be greatly appreciated.
    Regards
    LRaghunahth

    Hi
    Thanks a lot for your reponse.
    Basically I am able to login thru sap* / ddic and can unlock the users / reset the password.
    But the customer wants to know why the user is getting locked and it happened because of any procedure miss whil performing the upgrade..
    if it is usual that users get locked during upgrade, any SAP Notes to refer..
    Thanks a lot for helping in this community.
    Best Regards
    L Raghunahth

  • Facing Parse Errors after upgrading database from 10g to 11g

    Hi,
    We are facing parse errors in the SQL's after upgrading database from 10g to 11g.
    Kindly look into below parse errors.
    ********************************** Parse Error *****************************************************
    Tue Aug 13 14:13:08 2013
    kksSetBindType 16173533-2: parse err=1446 hd=3c73061fb8 flg=100476 cisid=173 sid=173 ciuid=173 uid=173
    PARSE ERROR: ospid=15598, error=1446 for statement:
    SELECT ROWID,ORGANIZATION_CODE,PADDED_CONCATENATED_SEGMENTS,PRIMARY_UOM_CODE,REVISION,SUBINVENTORY_CODE,TOTAL_QOH,NET,RSV,ATP,ORGANIZATION_NAME,ITEM_DESCRIPTION,INVENTORY_ITEM_ID,ORGANIZATION_ID,LOCATOR_ID,LOCATOR_TYPE,ITEM_LOCATOR_CONTROL,ITEM_LOT_CONTROL,ITEM_SERIAL_CONTROL FROM MTL_ONHAND_LOCATOR_V WHERE (INVENTORY_ITEM_ID=:1) and (ORGANIZATION_ID=:2) order by ORGANIZATION_CODE,SUBINVENTORY_CODE,REVISION, organization_code, padded_concatenated_segments
    Tue Aug 13 14:13:10 2013
    kksfbc 16173533: parse err=942 hd=3c387c4028 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
    PARSE ERROR: ospid=29813, error=942 for statement:
    Select feature from toad.toad_restrictions where user_name=USER or user_name in ( select ROLE from sys.session_roles)
    kksfbc 16173533: parse err=942 hd=3c97d83648 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
    PARSE ERROR: ospid=29813, error=942 for statement:
    SELECT password
    FROM SYS.USER$
    WHERE  0=1
    kksfbc 16173533: parse err=6550 hd=35185e4278 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
    ----- PL/SQL Stack -----
    ----- PL/SQL Call Stack -----
      object      line  object
      handle    number  name
    319e277050        30  anonymous block
    319e277050        57  anonymous block
    PARSE ERROR: ospid=29813, error=6550 for statement:
    BEGIN sys.dbms_profiler."146775420110782746251362632012"; END;
    kksfbc 16173533: parse err=942 hd=3c142d8600 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
    ----- PL/SQL Stack -----
    ----- PL/SQL Call Stack -----
      object      line  object
      handle    number  name
    319e277050        67  anonymous block
    PARSE ERROR: ospid=29813, error=942 for statement:
    SELECT 1 FROM plsql_profiler_data WHERE 0 = 1
    Please help.
    Regards
    Suresh

    Hi Suresh,
    Apologies for misunderstanding..
    Tue Aug 13 14:13:08 2013
    kksSetBindType 16173533-2: parse err=1446 hd=3c73061fb8 flg=100476 cisid=173 sid=173 ciuid=173 uid=173
    PARSE ERROR: ospid=15598, error=1446 for statement:
    SELECT ROWID,ORGANIZATION_CODE,PADDED_CONCATENATED_SEGMENTS,PRIMARY_UOM_CODE,REVISION,SUBINVENTORY_CODE,TOTAL_QOH,NET,RSV,ATP,ORGANIZATION_NAME,ITEM_DESCRIPTION,INVENTORY_ITEM_ID,ORGANIZATION_ID,LOCATOR_ID,LOCATOR_TYPE,ITEM_LOCATOR_CONTROL,ITEM_LOT_CONTROL,ITEM_SERIAL_CONTROL FROM MTL_ONHAND_LOCATOR_V WHERE (INVENTORY_ITEM_ID=:1) and (ORGANIZATION_ID=:2) order by ORGANIZATION_CODE,SUBINVENTORY_CODE,REVISION, organization_code, padded_concatenated_segments
    Assuming you see the above error message in the alert log file, which was your original post, follow the below steps:
    1 Get the 'ospid' value from the error
    2. Issue the below command:
    SQL> select request_id,ORACLE_PROCESS_ID
      2 from fnd_concurrent_requests
      3 where request_id = 15598;
    3. After obtaining the request_id
    4, Query it from the front-end using SYSADMIN responsibility
    Hopefully this should get you the respective concurrent report/program.
    Thanks &
    Best Regards,

  • "The query was cancelled" error after upgrade from 10.1.3.3.3 to 10.1.3.4.2

    Hi,
    I was using OBIEE 10.1.3.3.3 /. After upgrading to 10.1.3.4.2 , the queries are not running ( long running queries alone) as expected. and so all the campaigns iwh tlong running queries are cancelled and the error message is seen in the xml log in Marketing jobs management.
    We have upgraded the OBIEE version from 10.1.3.3.3 to 10.1.3.4.2 yesterday after which the connectivites have been checked with SQLPLUS and they are working fine. But when the campaign has been loaded, the Analytics have received the request for the segment query and after longer run, the task has been cancelled with the error message "The Query was cancelled as mentioned below in the Job Stats
    <jobStats>
    <jobID>2</jobID>
    <jobType>WriteListFiles</jobType>
    <jobUser>userid</jobUser>
    <jobState>Error</jobState>
    <jobTotalMilliSec>1h 41m 21s 160ms</jobTotalMilliSec>
    <jobStartedTime>2012-03-22T08:06:13Z</jobStartedTime>
    <jobFinishedTime>2012-03-22T09:47:34Z</jobFinishedTime>
    <jobIsCancelling>N</jobIsCancelling>
    - <exception>
    <message>Job request of type "WriteListFiles" failed.</message>
    - <exception>
    <message>Error executing the list generation SQL.</message>
    - <exception>
    <message>Error in executing cursor for WorkNode (Id:0)</message>
    - <exception>
    <message>The query was cancelled.</message>
    </exception>
    </exception>
    </exception>
    </exception>
    </jobStats>
    Please let us know the suggestions
    So far, the unaccessedtimingrunoutminutes tag has been tried to set 50 under ODBC tag in instanceconfig.xml. and the defaulttimeoutminutes has been tried to set to 150 in the same instanceconfig.xml.
    along with that the rpd changes are done. For all the users apart from the Administrator, the timeout has been changedfrom 10 minutes to 150 minutes. But still that way is not working.
    The segments was fired with the Administrator login. So , if the timeout for admin login can be set, i assume that the problem might be solved. Please let us know ur suggestions here too.
    If that is the case, when we open rpd , only for Administrator user and group, the Permissions button is disabled. So i want to know how to change for Admin user settings in rpd..
    Please advice us on the same.
    Regards,
    Madasamy M.
    Edited by: Madasamy Murugaboobathi on Mar 26, 2012 1:40 PM

    The issue has been resolved by setting the following parameters
    <UnaccessedRunningTimeoutMinutes>120</UnaccessedRunningTimeoutMinutes>
    <DefaultTimeoutMinutes>120</DefaultTimeoutMinutes>
    <ClientSessionExpireMinutes>120</ClientSessionExpireMinutes>
    <ConnectionExpireMinutes>120</ConnectionExpireMinutes>
    <UIDefaultTimeoutMinutes>1440</UIDefaultTimeoutMinutes>

  • Build error after upgrading from 8.2.1 to 8.5 "Error 1055 occurred at Invoke Node..."

    After upgrading to 8.5, I'm getting the following error when trying to build an EXE:
    Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
    Error 1055 occurred at Invoke Node in AB_Source_Library.lvclass:Close_Reference.vi->AB_Build.lvclass:Copy_Files.vi->AB_Application.lvclass:Copy_Files.vi->AB_Build.lvclass:Build.vi->AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
    Possible reason(s):
    LabVIEW:  Object reference is invalid.
    I have been building this application for both Windows and Mac OS, and I even get the same error when building the .app on an Intel Mac.
    Things that I've already tried:
    * Mass-compiling all my code
    * Created the project from scratch
    * Enabled each panel of the "diagram disable structure" one at a time and compiled again
    Any ideas?

    Hi Travis,
    Ben’s advice if definitely the best place to start. Error 1055 is a very general LabVIEW error for “Object reference is invalid.” The cause is usually a bad install where important LabVIEW function aren’t placed in the right directory or aren’t installed at all.
    Charlie M. CLD

Maybe you are looking for