Audio is not decoding properly on text messages sent from Motorola Android. Video plays fine but audio is unintelligible chirping.

I have iphone4. Some inbound text messsages with imbedded video clips do not play the audio properly. Audio chirps as if bad decode. Is there firmware/software updates or other apps to help with this issue?

Harm, I didn't pay attention to those settings, I should have. I got hung up in the preset names and figured those were my only choices. How green I am, lol. I made a preset with a Target of 4 (max 6) and VBR 1 Pass, and I knocked the audio down to 128K being it's just speech, and it all worked great. The new file plays in both players perfectly and also plays on my iPad with no jitter. Filesize is about 240mb but that's fine, it works. Problem solved and in the books. BTW, I use a GTX570.
Jim, I agree, VLC is super, it was the only player that would play 5D Mark II files right out of camera back in 2008, on my dual core Dell laptop with a cheesy Nvidia 7900 graphics card. Problem is, the majority of people I'm sending these MP4s to are Mums & Dads in our church, etc, and you know quite well that those folks are running some consumer Dell or HP setup they bought at Costco on closeout.
Funny backstory, when the 5D2 came out in Sept 2008, that was what thrust me into video. So I immediately bought the Prod Premium CS4 Suite (already owned Photoshop for a few years being a stills guy) and installed it on that Dell 17" laptop I mentioned above. After getting the 5D2 finally in Jan 2009, I actually had the nerve to take my first attempt at creating a video in Premiere and encoding it on that laptop. I literally had to kill AME partway through because I was seconds away from burning out my processor (I had been using RealTemp because of how hot that thing ran using Word, lol). It was that event that made me convince myself to start researching how to build a real editing PC (using an i7 920 at the time). I probably drove Harm nuts back then with all my questions, lol! But this rig has been my workhorse and has been through countless upgrades, the only thing remaining from the original 2009 build is the case and the power supply.
I know, you guys didn't need all that info, just felt like shooting the breeze. Thanks again!

Similar Messages

  • HTC Sensation not able to open text messages sent from iPhone4 iOS6

    Up until I installed iOS 6, my friend had no trouble receiving and opening a standard (green) text message sent from my iPhone4. After the new install, his phone receives the message but as a text file that won't open. He hasn't changed anything on his end nor have I changed anything else, so I'm assuming this must be the culprit. Has anyone else had a similar issue? Thank you for any suggestions.
    Bryan

    Have you figured this out yet?

  • My wife and I each have an iPhone 4S. With the upgrade to ios6 all text messages sent from my phone show up on hers to include responses from my text. text that she sends from her phone appear as if from mine. How do we stop it?

    My wife and I each have an iPhone 4S. Ever since the upgrade to ios6, text messages sent from my iPhone also appear on hers? All response to those text also show up on both devices. Likewise, text sent by her appear to others as having been sent from my iPhone. I have tried turning group messages off but nothing works. How can I correct this on both phones? Appreciate any help.

    Rectory wrote:
    Please can someone tell me how  I can change this so when I send a mail from my phone and from the IPad that it reads from me.
    You need a separate email address but you've already ruled out that solution.

  • Text messages sent from or to my iPhone do not appear on the Verizon Messanger web app.

    iPhone text messages do not appear in the Verizon Messenger web ap. Any Ideas why this happens? All other text messages I can still receive!!!

    If you are referring to iMessages, they won't show up in the Verizon Messages app since they don't go through Verizon's servers, they go through Apple's.

  • Text Message sent from LabVIEW using ActiveX and Internet Explorer

    I am fairly new to LabVIEW and I am trying to make a VI that will be able to text me and let me know when a test is about to be done or if something has caused it to shutdown.  My VI uses www.onlinetextmessage.com but I can't get it to click the Send Message button. 
    I can get it to insert text in the text fields.  I just can get it to click send.
    Can you help me?
    Solved!
    Go to Solution.
    Attachments:
    My Texting.vi ‏38 KB

    MoonMan wrote:
    Well it sure seemed like that should have worked but no luck. When I try to add the FormElement with submit in my VI after I wire in the reference wire it automaticaly changes to a regular Element.  Then it wont run because submit is not an option for Element, I have to change the submit back to click. 
    I dont understand, it really seems like the click should work, and it seems like the submit should have also worked.  Getting text into the different fields was easy enough.
    Did you try my modified version?  That uses IHTMLFormElement properly.  If you then change the element name from "Send Message" to "txtmsg" (the name of the form), it appears to work - or at least, it pops up an advertising window in Internet Explorer (I didn't fill in any of the fields as I don't want to give out my phone number or email address to some random website, especially one that pops up advertising).
    When you try to change to FormElement, what steps are you taking?  Are you changing the type of the "type" input to Variant to Data?  You'll need to right-click on that constant, Select ActiveX Class... and choose IHTMLFormElement.
    As a LabVIEW style note, you should close all the ActiveX references you open.  That means all the references (IHTMLFormElement, IHTMLElementCollection, etc) need a Close Reference when you're done with them.
    Again, I think sending an email is a better way to send a text message from within LabVIEW, and for that matter, you might be able to find a better website for doing it.  TMobile allows their subscribers to send SMS messages through their website and it appears that AT&T provides a similar service; Verizon provides a web page to send SMS to their users.
    EDIT: by the way, the submit button is not a named element (it has a "Value" property but not a "Name" property) so you can't get a reference to it by name.  If you probe the item output of the IHTMLElementCollection property node, you'll see it returns an empty variant, which is why "click" has no effect.

  • How NOT to save iCloud Mail messages sent from iPhone?

    Using iCloud Mail on a MacBook / Safari, e-mail messages are NOT saved - the relevant box in Preferences is unchecked. However they are saved in the Sent folder when sent from an iPhone. Is there any way they are NOT saved either way?

    Again, ON MY IPHONE only has Sent option. There's no way you can set the Sent mailbox to any Trash anywhere.

  • Is it true text messages sent from my IPad can not be sent only to individuals who apple have iPhone or iPad  technology?

    I can not text individuals who do not have iPhones or IPads from my iPad.

    You can also send to iPod Touches or Macs.
    If one does have an iPhone it can be used in conjunction with an iPad, iPod Touch or Mac to send SMS/MMS messages to non-Apple devices.

  • Does anyone know of an app or way to recieve a text message notification from an android phone to my iPad - same wireless carrier

    Is there a way for my android obsessed brother to send me a text and I can receive notification on my iPad (which is near me more than my iPhone). It seems like it should be 'easy' because we share the same carrier (and family plan), and my iPhone number is linked to my profile (ie FaceTime, iMessage, etc.). Any ideas? Maybe an app work-around?
    Thanks All!!

    SMS uses the voice channel.
    iPads do not connect to the voice channel and do not do SMS.
    You can download apps like text+ that use their server to receive SMS messages.

  • Xha1 24F footage Video plays fast but Audio is normal. PPro 2.0

    Hey Gang, I am having some trouble with my 24f footage from my xha1 into PPro 2.0. I have installed the canon F presets and imported footage using the 24f setting but when I play it back in the timeline my video/audio is out of sync. Even when I export it nothing changes. My video is playing to fast, but my audio is normal. I have played around with unlinking footage and trying to find the correct video speed, with no luck. I have also tried using the footage on 30f timelines with no luck either.
    I have looked around for the answer but nothing of this particular issue has come up.
    Any thoughts?
    Much appreciated.

    Apart from the much better job done by freeware like HDVSplit or shareware like Scenalyzer, than has ever been delivered by Adobe for $$$, it is worth noting that all HDV cameras, like the H1, A1, G1, Z1 and all the other models available, have one thing in common. They all use a tape recording mechanism.
    People often forget that this tape mechanism runs at a pre-defined speed, enabling 50Hz (PAL) or 60Hz (NTSC). Nothing else. Even if you set your camera to 24P or 24F or whatever other settings are available in the camera, the tape speed is not changed. The tape runs at the same speed regardless of your camera settings. Keep that in mind when capturing.

  • YouTube video plays fine, but video on some sites does not

    Shockwave Flash is set to 'Always Activate' but:
    -Some videos on www.eminiaddict.com say that a plugin is needed.
    -Videos on www.dickmorris.com are chunky and tiled.
    The above two play fine on IE.

    Thanks for the reply but I have never used QuickTime, nor the plugin.
    The problem started when I recently migrated from an XP laptop to a new Win7 laptop, with a new installation of Firefox, using MozBackup to transfer the profile.
    I did solve one problem by following the instructions here:
    https://support.mozilla.org/en-US/kb/windows-media-or-other-plugins-stopped-working
    The tiled and chunky video at www.dickmorris.com remains.
    See pic.

  • My family of four (2 iPhones, 2 iPods) all share the same iTunes account.  Many text messages sent to or from mine or my husband's phones are also received on my daughter's iPod, and vice versa. How do I fix this?

    How can I keep text messages sent from my or husband's phone from being received on daughter's iPod, and vice versa? We have five devices on one iTunes account - 2 iPhones, 2 iPods and an iPad.

    Hello Hrd1977,
    This is typically caused by both devices sharing an Apple ID for iMessage and FaceTime.  I would recommend signing out of iMessage on your daughter's device.  Go to Settings > Messages > Send & Receive, tap your Apple ID, and select Sign Out. Then sign in with the desired Apple ID.
    iOS: Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    Cheers,
    Allen

  • Youtube plays fine but not Facebook or other site videos, it says I am missing a plugin?

    When I use Youtube the videos play fine but on Facebook and some other sights the videos will not play. I just get a message that says a plugin is missing. Everything works fine on IE. I just downloaded Mozilla last night.

    hi Brandonacker, you probably need to install the adobe flash player plugin for those sites to show video content, which you can download from https://www.adobe.com/products/flashplayer/distribution3.html (use the windows exe-installer for plugin based browsers)

  • TS3623 Purchased Weeds from iTunes and the audio is very messed up. Video is fine. Audio for other downloaded shows etc. is fine. Any ideas or suggestions?

    I purchased Weeds from iTunes and the audio is very messed up ( loud like a lawn mower ). The video is fine. Audio is fine on all other purchased shows, Netflix etc. Any suggestions?

    Welcome to the Apple Community.
    Select the content which is causing a problem and use the 'Report a problem' button in Your Purchase History.

  • Some of my contact names are not appearing when they text message me.  They are just showing up as their numbers. I have them saved in my phone so i am not really sure why their names aren't showing up when they message me?

    some of my contact names are not appearing when they text message me.  They are just showing up as their numbers. I have them saved in my phone so i am not really sure why their names aren't showing up when they message me?

    I have this identical problem.  For a while my group texts didnt show up on my ipad.  Then one day they did, maybe everyone in the group started using the same os version or something.  Ever since my first reply to the group there have been complaints of multiple threads.  I can not find a pattern for when my group text's decide they want to create a new thread. (it doesnt happen every time)  Everyone in the group has deleted the thread, we've all toggled imessage on/off etc.  There still hasn't been a solution.
    Any help would be appreciated.
    Thanks

  • How can I get my ES2 loops to play correctly? I keep getting the message that the audio is not found when I drag the loops from my audio browser even though they play fine in the preview.

    How can I get my ES2 loops to play correctly? I keep getting the message that the audio is not found when I drag the loops from my audio browser even though they play fine in the preview.

    It's exactly as I stated. Whenever I try to drag these kinds of loops (ESX24 / software instrument loops? the ones marked in green with the white music note next to them) from the loop browser into the timeline a message comes up saying Audio Not Found for that loop.  And a new track is created automatically when loops are dragged into the timeline, so I'm not creating some other random / synth instrument track so I'm not sure  what the deal is... But perhaps I'll try creating a software instrument track first and then drag the loop into that track and see what happens - maybe there's something with the default settings that automatically creates audio tracks whenever loops are imported?

Maybe you are looking for

  • I HATE the Droid "Incredible" and I can't wait till my contract ends!

    I'VE BEEN WITH VERIZON FOR 9 YEARS AND I'M SO OVER THERE SERVICE! I HAVE HAD THIS PIECE OF CRAP PHONE FOR ALMOST TWO YEARS (20 MONTHS TO BE EXACT) AND IT HAS BEEN NOTHING BUT PROBLEMS AND ISSUES FOR STARTERS, (removed to comply with VZW Community ToS

  • Reading a text file with GUI_UPLOAD

    Hello,   I'm trying to read a text file into an internal table of text lines using GUI_UPLOAD. The problem is that I can only read a maximum of 255 characters from each line. So for example, if the first line in the text file contains 260 characters,

  • Code Dilemma

    Hello everyone,                           In ABAP, how do I check to see if a field is null and if it is then fill it in with some value.  I have the following statement however, I am pretty sure this not correct because it seems to overwrite all my

  • Pricing Conditions deactivation at header level of Sales Order

    Hello there, We have used a routine in pricing procedure (BaseType Routine) to deactivate condition MWST in the MWST condition line in pricing procedure, transaction V/08. In the routine, We played with the KINAK (set to K )and KOBLI (set to space) f

  • Plugins for converting Grayscale to neutral CMYK?

    I've some B&W images that were processed as RGB, turned to Grayscale, and eventually need to be CMYK. They're being printed in a magazine, and it's important that they don't have a weird color cast. I feel a straight convertion from Grayscale to CMYK