Audio Output from Multiple Sources not working

When I have more than one audio source open i.e. VLC + skype, skype + netflix, the later fails to produce any output -- even if the former is paused. I haven't done anything none standard with my configuration in this regard.
lspsci
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
aplay --list-devices
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC269VC Analog [ALC269VC Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
lsmod
snd_seq 61165 0
snd_seq_device 13307 1 snd_seq
snd_hda_codec_hdmi 49263 1
snd_hda_codec_realtek 67322 1
snd_hda_codec_generic 63161 1 snd_hda_codec_realtek
snd_hda_intel 26387 6
snd_hda_controller 26857 1 snd_hda_intel
snd_hda_codec 112621 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
snd_hwdep 17244 1 snd_hda_codec
snd_pcm 88779 5 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 26614 3 snd_pcm,snd_seq
snd 73436 21 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel,thinkpad_acpi,snd_seq_device
soundcore 13031 2 snd,snd_hda_codec

I think I resolved this! I had the same issues you have been having for a few months. I am actually running Vista. Here is what I did...
1. While booted to Windows I uninstalled boot camp
2. Re-installed boot camp from Leopard DVD
3. Installed boot camp update 2.1 (downloaded from Apple support, i know this is for XP only, but I updated anyway.)
4. Downloaded the realtek drivers (high definition audio codecs) from http://www.realtek.com.tw/downloads/
5. DO NOT use the Realtek installer to install the drivers...instead extract the contents to a folder.
6. Go to the device manager, locate the High Definition Audio device and updated the drivers from here (point to the folder where you extracted the drivers).
I now have sound out of the rear jack!! Hope this help someone
Regards,
Blaine

Similar Messages

  • Audio Output from Mac Pro not working in XP

    I'm trying to make the audio line output of the Mac Pro work in XP. the only sound comes from the motherboard or headphones in front of the computer.
    Under audio devices say "realtech HD audio device" This is the Apple mac pro?
    How do I turn the audio output on?

    I think I resolved this! I had the same issues you have been having for a few months. I am actually running Vista. Here is what I did...
    1. While booted to Windows I uninstalled boot camp
    2. Re-installed boot camp from Leopard DVD
    3. Installed boot camp update 2.1 (downloaded from Apple support, i know this is for XP only, but I updated anyway.)
    4. Downloaded the realtek drivers (high definition audio codecs) from http://www.realtek.com.tw/downloads/
    5. DO NOT use the Realtek installer to install the drivers...instead extract the contents to a folder.
    6. Go to the device manager, locate the High Definition Audio device and updated the drivers from here (point to the folder where you extracted the drivers).
    I now have sound out of the rear jack!! Hope this help someone
    Regards,
    Blaine

  • Realtek HD Audio: Output:OK, Input (Mic): NOT WORKING??!?!?!?!?!?!?

    Hi guys,
    I am going to tell you and ask for your advice the wierdest thing happens to my 14-month old Pavilion 6300 series:
    - The PC has Realtek HD Audio built-in (on-board) and having the latest driver (I downloaded off from realtek.tw, latest is 5.10.0.5874)
    - Before I installed that Realtek driver, I had installed Microsoft UAA Bus driver for HD Audio (version 5.10.0.5010)
    - I am running Windows XP Professional SP3
    When I plug in a headset (with mic of course, for skype), strange things start like this:
    1. I can hear the output sound, the jack can detect which plug I plug in
    2. But the INPUT (back or front) which is in my case, the MIC, DOES NOT WORK AT ALL.... Jeeze, it drives me NUT!!!
    3. I have turned on ALL the volume related to "MIC" but to no avail. Even the Recording mic volume is grey-out... really no-hope?
    4. I did the Hardware test, it could not detect the mic (no movement from the sound bar)
    5. The headset works well on other machine!!!!
    Can somebody tell me that the onboard card got a problem and I have to buy another card???
    Thanks a lot in advance guys, really
    James
    Message Edited by Jamesnb on 06-26-2009 12:19 PM

    now what you can try is can try to test the MotherBoard once and if there is any issue with the onboard card then you have to replace the card.
    if there is no issues with the MotherBoard then try entering device manager in safemode and uninstall the drivers once and check if its working.

  • Bluetooth audio streaming from android phone not working

    i am not able to play songs from my android phone on the laptop

    Bump.
    Still interested in getting this functionality.
    Any tips?

  • Satellite L-50 can't play audio from multiple sources

    I can't play audio from multiple sources. This is very annoying when I have 2 youtube videos playing, if I start playing something on the media player, there is no sound on media player, it's the same when I have 2 media players open and 1 youtube video playing, youtube video doesn't have sound..
    I already have all the latest drivers, last DTS driver update was in 2014, sound update this year's february..
    25/02/14
    DTS Studio Sound
    DTS Inc.
    Windows 8.1 - 64 Bit
    1.01.2700
     I don't know if this makes sense, but I got newer DTS sound driver which I found, It's not my laptop model, but they all seem to be the same - v1.1.88.0 
    I uninstalled DTS software and still had the same problem, so it's not affecting sound driver in any way..
    10/02/15
    Sound Driver
    Integrated Device Technology Inc.
    Windows 8.1 - 64 Bit
    6.10.6491.0
    IDT audio driver has newer release date, but the driver version is the same as the 2013 one..
    Why are toshiba releaseing old driver as 'NEW' ?
    2nd is my speakers advanced settings, nothing changed when I disabled "Allow applications to take exclusive control of this device"
    Attachments:
    audio.png ‏6 KB
    test2.png ‏7 KB
    specs.png ‏16 KB

    Can you check the full model and part number from the laptop?
    - Peter

  • Satellite L50-A-19N can't play audio from multiple sources

    I can't play audio from multiple sources. This is very annoying when I have 2 youtube videos playing, if I start playing something on the media player, there is no sound on media player, it's the same when I have 2 media players open and 1 youtube video playing, youtube video doesn't have sound..
    It goes away when I plug out my headphones..
    I already have all the latest drivers, last DTS driver update was in 2014, sound update this year's february..
    25/02/14
    DTS Studio Sound
    DTS Inc.
    Windows 8.1 - 64 Bit
    1.01.2700
    I don't know if this makes sense, but I got newer DTS sound driver which I found, It's not my laptop model, but they all seem to be the same - v1.1.88.0
    I uninstalled DTS software and still had the same problem, so it's not affecting sound driver in any way..
    10/02/15
    Sound Driver
    Integrated Device Technology Inc.
    Windows 8.1 - 64 Bit
    6.10.6491.0
    IDT audio driver has newer release date, but the driver version is the same as the 2013 one..
    Why are toshiba releaseing old driver as 'NEW' ?
    2nd is my speakers advanced settings, nothing changed when I disabled "Allow applications to take exclusive control of this device"

    I see that the option called “give exclusive mode applications priority” has been checked.
    Usually different applications and programs can access the sound card simultaneously.
    For example: you can hear the sound in game, while you can run your own music via an external player.
    This is prevented with these options “give exclusive mode applications priority”.
    Maybe you should disable (uncheck) this option to prevent the different applications for using this exclusive mode stream.
    I did it for my DAC. I set the DAC for exclusive mode. Once my audio playback software starts to play music, no other software is able to share the DAC.
    However, I use Win 7 and Realtek sound driver… It’s another configuration.
    So it’s not known to me if your issue is related Win 8.1 system or maybe limitation of sound driver… it could be also possible that one of your sound applications don’t allow multiple sound streaming.

  • When I unplug Apple headphones from my MacBook Pro sond from internal speakers not work, and system soud preferences displayed: Output: optical digital out port only

    When I unplug Apple headphones from my MacBook Pro sond from internal speakers not work, and system soud preferences displayed: Output: optical digital out port only

    If you see a red light in the audio output port, then the internal switch is stuck.  Insert the earphone plug a few times and see if you can trip the switch.  If that fails, insert a cocktail stirrer and the like and jiggle it around inside.  If that fails, take it to an Apple store and have the technicians at the genius bar do it for you.
    Ciao.

  • TS3789 digital audio from apple tv not working

    the digital audio output from my apple tv to my reciever was working initially. It is no longer working. Any ideas?

    Welcome to the Apple Community.
    Have you tried adjusting the "Audio Out" and the "Dolby Digital" settings in settings > audio and video? It may be worth trying several combinations of these settings, although typically it is the "Dolby Digital" setting that causes most problems for users.
    Also make sure that you have correctly mapped the input port on your sound system to the output, if you are unsure about how to do this, refer to the manual that came with your sound system.
    Have you tried playing various content sources (i.e. podcasts, music, iTunes Store video, other video etc), do you have the same problem with all types of comments? You might also check that you can see a red light at the end of your optical audio cable. Is your optical audio cable plugged straight into your sound system, or does it go through a switch or other device?

  • I'm working on DC Motor control using DAQ. There is sufficient voltage output from DAQ but not current. What should i do so as to drive the motor

    I'm working on DC Motor control using DAQ. There is sufficient voltage output from DAQ but not current. What should i do so as to drive the motor. Could you suggest me appropriate driver IC using which this problem can be solved.
    Saravanan.T

    You really should use a DC motor controller to control a DC motor, look at the 754410 IC for a good example. You should be able to interface these to most DAQ devices.
    Alan

  • Open Hub - Data from multiple sources to single target

    Hello,
    I am using Open Hub to send the data from SAP BI to Flat files. I have a requirement where I want to create a single destination from multiple sources. In other words in BI we have different tables for attributes and text. I would like to combine the data from attributes  and text into a single file. For eg. I want to have material attributes and text in the same single file as output.
    Is this possible in Open Hub? If yes could you please help me to understand the process.
    Thanks,
    KK

    Hi,
    1. Create the Info Spoke and activate it
    2. Change it and go to transformation
    3. Check the box InfoSpoke with Transf. Using BAdI
    4. You are asked if you want to generate the spoke. Say yes & Simply set some texts and activate here, then return.
    5. You can now change the target structure. Simply create a Z structure with all the attributs & text field in it in the SE11 and enter it here.
    6. Double click on BAdI implementation & then double click again on "TRANSFORM" method of the implementation. It will take you to method  
    "IF_EX_OPENHUB_TRANSFORM~TRANSFORM"
    7. Write a code to select & fill the text field & map other filed with the attribute fields.
    Example:
    ZEMPLOYEE_ATTR_STRU - Target Structure for InfoSpoke EMPLOYEE_ATTR
    EMPLOYEE     /BI0/OIEMPLOYEE     NUMC     8     0     Employee
    DATETO     /BI0/OIDATETO     DATS     8     0     Valid to
    DATEFROM     /BI0/OIDATEFROM     DATS     8     0     Valid from
    COMP_CODE     /BI0/OICOMP_CODE     CHAR     4     0     Company code
    CO_MST_AR     /BI0/OICO_MST_AR     CHAR     4     0     Controlling Area of Master Cost Center
    HRPOSITION     /BI0/OIHRPOSITION     NUMC     8     0     Position
    MAST_CCTR     /BI0/OIMAST_CCTR     CHAR     10     0     Master Cost Center
    TXTMD     RSTXTMD     CHAR     40     0     Medium description
    Note: Text and attribute are in same structure.

  • No audio output from the orange mini j

    Hi all,
    I am having problem with my Audigy 4.
    Hope you know what I mean, there are three 3.5mm mini jacks
    of three different colors: green, black, and orange.
    I have noticed that there are audio outputs from the green and black mini jacks only, while the orange mini jack seems to be not working at all.
    When I plugged an earphone line to the orange mini jack,
    I could hardly hear any sound from it.
    Any idea?Message Edited by kwfine on 07--2007:03 AM

    The orange jack is the center/subwoofer audio jack. If you're using a 5. speaker system. Make sure you have selected 5. speaker setting in the speaker setup software.
    Jason

  • Managing Photos from multiple sources to iPhoto '11 Photo Stream on Mac.

    I combined photos from multiple sources (camera, desktop, iPhone) to iPhoto '11 on Mac.  I determined keeper photos and put them in Event.  I also rated and flagged the keeper photos.  I want to delete the rest of photos from Photo Stream but can't see rating/flag so I can't determine which ones to delete.
    This is basic file management but not finding a solution.  Suggestions?

    The Photo Stream is designed to push your images into the cloud the moment they are taken. It does not (yet) support to show the ratings and most of the tags.
    If you have an event with all photos you want to keep, the easiest way would be to delete all photos from the Photo Stream (on all your IOS devices) and then add only your selected "keeper" images to the Photo Stream again.
    Regards
    Léonie
    Added: It is not safe to rely on the Photo Stream for storage, since it will only keep a snapshot of currently added photos - the last month's photos or the last 1000 photos. You have have no control over the sorting of photos in the stream or how long they will be kept. The Photo Stream is a means of sharing, not of storing images. I prefer to use "Shared Photo Streams" for more permanent photo selections. These will show exactly the selection of images I add to them, and they are not automatically erased after a month.
    iCloud: Using and troubleshooting Shared Photo Streams

  • Multi channel audio outputs from a laptop such as 5.1 or 7.1

    is it possible to get multi channel audio outputs from a laptop such as 5.1 or 7.1 for watching Movies or television while using Windows media Center.

    Ok so i order to help anyone who is interested.
    The only ironic solution to this problem i found was to use a plugin called xto7 to convert the xml to the old fcp7 format.
    i then imported this into premiere pro.
    this was then able to export an OMF that when imported into logic 10 that was using the correct 6ch mono setting as separate tracks.
    Insane but it works until Apple fixes the incorrect meta data import in FCPX that sets the xml export to the default import that is always surround.
    this is the only way i was able to send stems with all the edit points and fades for the sound editor.
    If you don't have premiere lying around you maybe able to do it with fcp7 too we just didn't have it in this studio.
    Fingers crossed Apple fixes the fcpx xml export.

  • Can we merge data from multiple sources in Hyperion Interactive Reporting ?

    Hi Experts,
    Can we merge data from multiple sources in Hyperion Interactive Reporting ?Example can we have a report based on DB2
    Oracle,
    Informix and Multidiemnsional Databases like DB2,MSOLAP,ESSBASE?
    Thanks,
    V

    Yes, Each have their own Query and have some common dimension for the Results Sections to be joined together in a final query.
    look in help for Creating Local Joins

  • Consuming PI Webservice from Webdynpro Java Not working

    Hello SAP,
    Environment: CE 7.2.
    Resolution expected immediately, Helpful answer is highly appreciated.
    Is the namespace should not exceed 60char for PI Webservice, for executing the webservice from Webdynpro Java.
    I tried with all the options in executing the PI Service from Webdynpro Java, None of the options worked. I am facing the below error while I was calling the PI Webservice.
    I don't see any problem from Webdynpro Java, what ever the procedure I have followed is the standard procedure.
    Fortunately when I execute the service from Webservice Navigator, it is working as expected. The same webservice when I consume it from Webdynpro Java it is not working
    Options tried so far:
    1) Published the Services to Service Registry and there by consuming the PI Service from Service Registry - Not worked
    2) Tweaked the URL with few options - Not worked (Tweaking the URL, ex: portType, Binding)
    3) Changing the Business Systems in PI and there after calling the service - Not worked
    4) Initializing the code, instead of creating Service Controller and calling the PI Service - Not worked.
    5) Created a Provider System and tried to call the PI Webservice from Provider System - Not Worked
    For all the Options, I am facing the same error which is provided in the screenshot.
    Below procedure which I have followed for calling the PI Webservice:
    1) Created Adaptive Webservice Model
    2) Provided PI Webservice URL (It prompts for PI System UserId and Password)
    3) Selected Option - No Service Group Configuration
    4) Provided Logical Destination
    6) Completed creation of Model
    7) Added the model as a UsedModel
    8) Right Click on Comp Contr. and selected Apply Template and Created a ServiceController for the model (Entire mapping to comp contr, Initializing the nodes is taken care by Service Contr.)
    9) Created an Template Action button and there by calling execute method which is auto rendered from CompContr..
    10) Build the project.
    11) Activated the code and Run the Application.
    12) Getting the below error which is showed in the message.
    ERROR MESSAGE:
    Exception on execution of web service on destination 'GetPIHRPeopleData' for operation 'SI_CreateHRPeopleData_OS' in interface 'SI_CreatePeopleCompany_OS'

    Hi Sankar,
    If the webservice is working fine in the Wsnavigator then there is some problem with importing the webservice in webdynpro for Java. Please check the required parameter for creating the Adaptive Webservice Model. After adding in the used model and compoent controller binding, you need to write code for to execute the webservice model.
    Please check the code for initialization and execution for the webservice and then test it.
    Best Regards,
    Arun Jaiswal

Maybe you are looking for