Audio skip in burned iDVD

I just burned my first idvd. It turned out very well with one small problem. During the photo slide show, the music stops for about 5 seconds. Any thoughts on correcting this? It didn't happen when I played it on the computer. Thanks Sandy

Sandy,
Welcome to the iDVD forum!
During the photo slide show, the music stops for about 5 seconds. Any thoughts on correcting this? It didn't happen when I played it on the computer.
You might try this DVD on another DVD player and see if the sound dropout occurs there too. Could just be your current set-top player doesn't like slideshows. One other possibility is your brand of blank DVD-R disks. I like Verbatim.
John B.

Similar Messages

Audio disappears when burning in iDVD 6 from QT movie (from FCP)

Before burning, checked all the chapters and each plays with audio. When the disc burns it does encode the audio during the burning process but the only audio that is present when the burn if completed is the audio on the 1st menu. I only inserted video on menus two and three (using "Full Frame" menu) as I only want video; no audio on those two menus . I had to force quit twice and then ran Repair Permissions. Should have I trashed iDVD prefs and if so, is there only one to trash?
thanks for any help . . .this forum is invaluable.

I had to force quit twice and then ran Repair Permissions. Should have I trashed iDVD prefs and if so, is there only one to trash?
drag and drop all incidents of the iDVD plist to the trash. Use the finder or spotlight to locate all incidents of plist for iDVD. Looks like this:
com.apple.iDVD.plist
secondly, you will need to repair permissions on the HD.
applications > utilities > apple's DU
third, delete all encoded assets from the advanced menu.
forth, recommend using different media like Verbatim DVD-R Minus media and burn from a disc image using apple's DU or Toast at 4x or slower.
fifth .....be very patient while it encodes and burns. i've seen some dvd's take up to 2 days.
sixth ....make certain you have no less than 20GB of available HD space.
Good luck!
SDMacuser

I made a movie with iMovie and cannot get the audio when I burn into dvd. I would like to transfer video to a dvd to be played in any computer and TV

I made a movie with iMovie and cannot get the audio when I burn into dvd. I would like to transfer video to a dvd to be played in any computer and TV

Go to the Map mode in your iDVD project and make sure the blue bin at the left is empty. That's where you drag slideshows to if you want the DVD to open immediately to that slideshow and bypass the menu.
Click to view full size
If there is an item in there drag it out.
OT

No audio on dvd burned with idvd6

Relevant software: Mac OS 10.4.11, iMovie 6.0.3, iDvd 6.0.3
Problem: No audio on dvd burned with iDvd
What happened: Created movie in iMovie (audio and video fine). Shared to iDvd (audio and video fine on playback). Burned Dvd. No audio on dvd but video is fine.
What I did:
1. Saved as disc file. Opened with VLC and DVD Player. No audio, video fine.
2. Deleted encoded assets in iDvd then 1 (above).
3. Removed non-Apple extensions in Library/Quicktime. Then 2 and 1 (above).
I've read other discussions about this same issue and followed those recommendations as well as that in the article http://docs.info.apple.com/article.html?artnum=303550.
Clearly I'm missing something. But, what is it? Anyone have any suggestions?

i too am having the same problems with iDVD 6.0.4. I just ended up wasting 5 hours of time burning these damned DVDs... what was really strange is that the first DVD I burned was a dual-layer, and I checked that one on a set-top DVD player and it worked fine. I then needed 5 more copies of the DVD, so I simply inserted a fresh dual-layer DVD into the drive at iDVD's prompt of 'Would you like to burn this disc again?'.
Assuming that they would all be fine since the first one was fine, I simply burned 5 more DVDs. Only now, checking them after I've wasted a godawful amount of time burning them, do I find that they're all f#$ked. Thanks apple.
Crap like this makes me steamed. My PC burning software doesn't have nearly the same simple, elegant interface as iDVD, but it also lacks this CATASRTOPHIC problem. I mean, dual layer DVDs are relatively pricey... so screw apple. i will be glad to go home to my PC after being forced to work with this junky, buggy software.

HT1583 sound stops part way through on burned idvd, but ok on computer edit.

Can anyone help, for the first time having a problem with a burned idvd which the sound stops part way through. If sound turned right up on TV muffled sound
is there. Edited on computer and all works fine with full sound right the way through, only trouble is on the disc. Have tried many discs, so does not appear to
be disc failure.
Appreciate any comments please

Hi
FIRST OF ALL - THE MAJOR ADVICE in this forum EVER !
In iDVD - Before Burning the DVD DO !
Save as a DiskImage
Double click on this .img icon
test the new Pseudo DVD (looks like a white hard disk) with DVD-tool
THEN
• DVD Brand - matters
• DVD type used - matters
• BURN SPEED - matters
• Audio file format - matters
WHAT did You use
I only use
- Verbatim
- DVD-R SL
- x2 max x4 - Best / High - IS NOT BEST
- .aiff - NO .mp3, .wma etc alient formats - from iTune EXPORTED OUT as .aiff ONLY
Yours Bengt W

Audio encoding locks-up IDVD

I've tried to burn DVD's on two mac's and built new movie in each. All goes well in the encoding until it starts the audio, then locks up iDVD.
Mac Mini Mac OS X (10.4.8)

Hi Willy
How do You really know that it has locked up ?
• By the info in Activity Monitor - iDVD doesn't answer
• By other means or by error message (if so what does it say?)
Activity Monitor - LIES !!!. Let it be (while processing)- several hours and it will be OK
If error message - Please tell us about what it says.
If the DVD coding time goes absurd (days and so) the You probably have
less than 20Gb free space on Your internal hard disk - resulting in heavely
virtual memory managment (a pay to UNIX that is the base for Mac OS).
(Yes You can run C-programs in terminal on Your Mac - You only need to
install C-compiler from install DVDs that You got with Your Mac)
Yours Bengt W

HELP! audio skips

I have a slideshow with clean wmv audio files that when I go to burn, the preview has skips in the audio. I burned it anyway and it, too, skips.
any idea what I can do to fix this?
Thanks!

Kari,
In general I prefer to add my video using a video editor rather than the Photoshop Elements slide show. Yes, I do realize that the PSE slide show editor will accept a few types of video files. However, it is not a video or an audio editor and in my opinion has really limited support for them.
I don't think I understand your workflow.
1- You reference a "WMV audio file": however my understanding is that a WMV file is a video file which may have audio as part of the video. Did you mean the WMV file that is created by the OUTPUT command of the PSE Slideshow editor?
2- You say Burn - are you burning a video DVD and if yes what software are you using to create the video DVD format?
3- I think in another thread you said you are using PSE 5: please verify that.

The audio skips between titles on my my slide show?

The audio skips between titles on my my slide show?

No rather foggy from a west coast Swedish out-look too.
If burn error - I would
• Use a very good brand of DVDs - Verbatim comes to mind (ever heard me say anything else ?)
• DVD type - DVD-R plays on even older DVD-players (No +/-RW - known problem makers)
• Burn speed - I set it to x2 or x4
Just to get best possibly result
Yours Bengt W

Video and audio skipping in PowerDVD 8

Hi,
I have an issue when I try to play DVD's in PowerDVD 8. Exactly every 5 seconds the video and audio skip, or jump/become choppy and I cannot watch a movie. I have been researching and trying to figure out what is happening but have no idea. Could it be the X-fi I have installed the latest beta drivers to no avail.
Anybody have this problem or have any ideas on how to fix it's I have updated all drivers/firmware for everything and still can't make it go, sigh.
I have the following specs:
Intel x38BT mobo
X-Fi Fatalitly champ.
4GB DDR3 RAM
9800 GTX
ASUS 8x dvd-rom
E8500 CPU
Win Vista 32-bit
Thanks

Try this utility:
http://www.thesycon.de/eng/latency_check.shtml
and post results.
Gigabyte Boards at least with x48 chipset have an audio latency bug that is only fixed via a beta bios update. I have no idea if this also might affect your board...

Audio skips after rendering

Does anyone know how to correct audio that skips after rendering? The video is fine and the audio matches up to the video but the audio skips as though it is going in and out. The movie is about 2 hours long and the first few clips were fine but now it is becoming a problem. I rendered both the video and audio at the same time then I went back and rendered only.....mixdown to see if I could get it to work......no luck. Any help would be greatly appreciated.

Tammy,
If we've dropped a bit of time for this part of the edit, you now have time for more fun aspects of it.
While I will casually monitor my Meters, I spend much more time with a good set of noise-canceling headphones, listening critically. The Meters are basically to point up potential issues. With Audio, if you have not invested in a really good set of headphones, do yourself a big favor, and sneak 'em into the budget.
Glad that you got things toned down.
Now, let's go on to Lesson 02 - The Audio Mixer. Unlike adding Keyframes to a Clip, when your cutting is done, you can apply Track Keyframes to attenuate (also Pan, etc.) you Audio Tracks to suit. One would just change the Send in that Track to Write, or Touch, and "ride the gain" with the slider, as is required. I probably do most of my Audio editing there, than addressing the individual Clips. First thing that I have done is cut back a bit on the frequency of the Track Keyframes in Edit>Preferences, as I find the default to add too many (and you can go in and adjust these by hand, if you need to "smooth" things out a bit.). One caution: do this when you are satisfied with the cuts, Clip placement, etc., as these Keyframes are applied to the Track. If you were to remove a Clip, and replace it, those Keyframes would apply to that new Clip, whether you want them to, or not. This trips some folk up, if they do the Audio Mixer thing too soon in the editing. Wait until you are "in love" with your Timeline otherwise. It's like scoring a Project. One does that as about the very last step, or much work will be repeated, and that is not fun.
Good luck,
Hunt

ATV2 Video pixelated and audio skipping

I don't think this is the same as the flickering issue or the frame dropping issue discussed by others. Thus, the new thread.
When streaming videos (movies or TV shows) from itunes to the ATV2 the picture will get pixelated with the missing portions turning green. The video will continue but the audio skips (exactly like a needle on a record player skipping back). If I exit the video to the menu then resume, the video plays fine for awhile until the problem arises again. To give you an example of the frequency, it happened about a dozen times during one 40 minute episode.
All software is updated to the latest versions and all hardware has been restarted. Content is encoded using handbrake using the ATV2 preset and then passed through MetaX for tags. The setup is as follows: stored on DROBO->firewire->iMac->802.11n(5Ghz)->Airport Extreme->ethernet->ATV2.
Anyone else having this problem?
Thanks!

Haven't been able to see a pattern yet. I can watch a recently encoded movie (1-2hrs) without it happening once, but like I mentioned, it happened 12 times during a single 40 minute tv show. Both were encoded using same version of handbrake and ATV2 preset.
How do these two files compare in terms of total average data rate?

Only half of some iTunes Matched songs on my iPhone will play, then audio skips to next song in playlist!

Several (maybe 5%) of iTunes Matched songs on my iPhone do this... at EXACTLY 1/2 way through the song.
EXAMPLE: At 2:25 of a 4:50 long song (Shania Twain - From This Moment) the next song in playlist (Taylor Swift - Tim McGraw) starts as the audio skips to beginning of next song in playlist. Oddly, Shania's attractive album artwork and title stays up while Taylor's tune plays (?)
When the timeline for the first Shania song hits the end, the artwork slides to Taylor Swift's CD Cover art and the timer slider adjusts to near the end of that song.
When I play same songs on the same playlist on iTunes (also downloaded from iTunes Match) this does not occur.
Does anyone else see this happen or are there any suggestions?
THANKS
geo

Hey Guys, from my late model iPhone 4, I am also seeing my iTunes Match songs terminate playing very abruptly ...some won't play at all ...others skip to the next track after 10 seconds.
I checked the source files on my iMAC, and they are 100 percent perfect.
Tried deleting them, recreating them, signing out and then back into iTunes with Match On & Off, etc ...still no resolution to these problems.
Maybe the MATCH product is crashing under it's own weight now? It used to be good, but now I am not so sure anymore.
Please post if you have any solution or suggestions.
Thanks!
Pat

Problem burning iDVD projects using external LaCie burner

I recently purchased a LaCie DL d2 DVD RW with LightScribe 16x from the LaCie company (12/07/2007). The LaCie burner is connnected via Firewire to my iMac. The iMac is a little over a year old and I am running Mac OS X (ver. 10.4.11).
The primary reason for my purchase was that I wished to create/burn iDVD projects on my iMac computer. The reason that I needed this product was due to the fact that, when I purchased my iMac, I made an error in judgement , and ordered it with a combo rather than a SuperDrive. So, while I am able to create iDVD projects and iMovies, I am unable to burn DVDs with of projects on the Combo Drive that came with the computer.
Thus far, however, I have not been able to burn a DVD with any of my iDVD projects. I am running iDVD 6 (ver. 6.04). When I attempt to “burn” a DVD disk the “Creating your DVD menu” appears. When I put in a blank DVD+RW 4x 4/7GB, it appears to go through the process (Prepare,,, Process Menus... Process Slideshows... Process Movies and Burn procedures). The DVD is then ejected and a message says that it is done and is “cleaning up.” However, that message never leaves the screen and when I click on the “Cancel” button, nothing happens. The iDVD application seems to lock up and I have to do a “force quit.”
I have tried this with three different projects, all with the same result. When I place the supposed “burned” DVD in the Combo Drive, it spins for a while and then kicks the DVD diskn out.
I have also tried launching Toast Titanium 7 (software that came with the LaCie burner). However, I see no place where I can “drag & drop” an iDVD project to the “drop zone.’ The closest thing seams to be “movies.” However, when I select that mode and go to my iDVD folder, all of the files are “grayed out.”
Can anyone help me out? Should I be able to burn iDVD projects with this unit? If so, what am I doing wrong.
Thanks for any help/advice that anyone can provide.
Jeff White

open up Toast 7, click on Video tab, click on Image File and drag your img. file to Toast.
John,
That's not correct. In Toast 7 you must use the Copy tab to burn a disk image to writable media. See page 94 of the Toast 7 manual.
(The procedure is slightly different for Toast 6 and Toast 8 but always involves using 'Copy')

Burning iDVD projects with external LaCie burner

I recently purchased a LaCie DL d2 DVD RW with LightScribe 16x from LaCie (12/07/2007). The primary reason for my purchase was that I wished to create/burn iDVD projects on my iMac computer. The reason that I needed this product was due to the fact that, when I purchased my iMac, I made an error and ordered the iMac with a combo rather than SuperDrive. So, while I am able to create iDVD projects and iMovies, I am unable to burn DVDs with my project.
Thus far, however, I have not been able to burn a DVD with any of my products. When I attempt a “burn” the Creating your DVD menu appears and when I put in a blank DVD+RW 4x 4/7GB, it goes through the process (Prepare,,, Process Menus... Process Slideshows... Process Movies and Burn procedures). The DVD is then ejected and a message says its done and is “cleaning up.” However, that message never leaves the screen and when I click on the “Cancel” button, nothing happens. The iDVD application seems to lock up and I have to do a “force quit.”
I have tried this with three different project, all with the same result. When I place the supposed “burn” DVD in the Combo Drive, it spins for a while and kicks the DVD out.
I have also tried launching Toast Titanium (software that came with the LaCie burner). However, I see no place where I can “drag & drop” a iDVD product to the “drop zone.’
Can you help me out. Should I be able to burn iDVD projects with this unit? If so, what am I doing wrong.
Thanks for any help that you can provide.
Jeff White

"Should I be able to burn iDVD projects with _*this unit?*_"
Which "model" & "generation" G5 iMac do you have?
Need this info so that the knowledgeable users can provide you with the proper troubleshooting solution(s).
http://docs.info.apple.com/article.html?artnum=301724-en How to identify your iMac
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh355.html Getting information about your computer
You can have this info displayed on the bottom of every post by going to 'My Settings' which is located in the column on the right under your name, and filling in the information asked for.
Thank you
Have you contacted LaCie Support?

Cd skipping after "burning cd" does burning a slow copy really prevent ...

I know I asked this question before but I wanted to bring it up again just 2 double check.
Cd skipping after "burning cd" does burning a slow copy really prevent your cd from skipping in lets just say "Denon" cd players?
Recently we have burned some copies and during play back on the denon sometimes they would skip and no even play the rest of the song.
What is the best way to prevent this from ever happening?

I always burn CDs at no more than 8x maximum. Preferably 2x. Call me old-fashioned but I can't see how a 48x or even 56x burn can ever work without putting tons of (hopefully correctable) errors on it.
As I understand it with let's say "Denon" cd players, if the built-in error correction algorithm is naff or the laser is slightly off then too many errors on the disc are going to show up as splunts and your CD is effectively WATF.

Audio skip in burned iDVD

Similar Messages

Maybe you are looking for