Audio Synch Problem Exporting From imovie 6

I have a created a large imovie project in imovie 6 using pictures and imported video. The project uses a lot of extracted audio voice overs on top of the photos.
While trying to export the video to quicktime or idvd, the audio gets out of synch at various points. I have tried exporting it many times using a variety of different options, and the audio remains out of synch, sometimes in different places with each export. Lastly, I have extracted the audio from the video clips for some of the more problematic portions of the project, but that has not proven successful.
The odd thing is that the movie plays perfectly while in imovie.
Any suggestions as to how to correct this issue?

Hi
Tedious situation.
To avoid this I'm kind of strict in Audio in two ways
A
• Material used if video is in same frame per minute - else I use JES_Deinterlacer to convert all to one standard. I use PAL = 25fps - one of my Cameras records ONLY in 30fps - (some people records in 24fps - to get a movie feel - I never)
So keeping the fps from Camera to (in my cases) DVD - gives a supperior result
B
• I'm strict in the kind of Audio formats I use - ONLY .aiff (or from miniDV tape Cameras) AND THEN 16-bit 48kHz or from Audio-CD (still .aiff as on normal CDs) and here 44.1kHz
If Camera is set to record in LP-mode or 12-bit Audio - Then I use an external Audio Editor to get this right
If from iTunes - I never use this directly - BUT - collect needed audio into a New PlayList - BURN THIS as a Standard Audio-CD (NO .mp3 - but .aiff here too) and then use the files on this CD in my movie project's in iMovie HD6 or FinalCut any varsion (or if forced to - iMovie'11)
Else read this
Audio Sync problems
• 12.bit - should be 16.-bit (from miniDV tape - set Camera right)
Avoid recording in LP-mode on miniDV tape. This tape must be play-backed by same Camera. When Camera dies
so does the video material in worst case.
• .mp3, .avi etc strange file formats - should be converted to .aiff 48kHz 16-bit
• in iMovie (up to HD6) - do - Extract Audio - it most often helps
• from iTunes - collect into a PlayList then Export out as an Audio-CD (not .mp3) and use the files on this (.aiff 44.1kHz)
• There seems to be a problem with slow-down resp speed-up. Has to be in specific steps as 25% 50% 150% 200%
else problems will arise
• Audio problems when transitions is in use - especially iMovie HD/HD6
a. Select video clips
b. Extract Audio (Advance menu/Extract Audio)
c. Now apply transition
d. eventually fine-tune end and start of extracted audio clips
Yours Bengt W

Similar Messages

Audio sync problem: exporting from FCP to Pro tools or soundtrack pro

--------------------------------------------------------------------------------
Final Cut Pro sound export for mastering.....sync problem
Hey,
I'm editing a 30 minute film and I have done most of the sound edit in FCP and Soundtrack pro and I want to now bring all the sound into pro tools to master the sound but every time i export sound into pro tools it seems to stretch by two or three seconds.
I have tried OMF, AIFF, XML, and Quicktime audio file sut to no avail!!!!
There are 50 tracks in the file so it is quiet large. It's not that there are handles of the file also as when I sync the file with the audio track with the video it syncs in one place but it is still out of sync in another.........It's as if the audio has been stretched!?!
If anyone has any advice it'd be much appreciated
Keith

Try mixing down the audio first. Sequence/Render Only/Audio mixdown.
You could even try exporting the audio with the Export QT movie command using "current settings" and reimport that file, Add that mixed down file to a copy of the sequence. If it syncs in FCP I'd think it will sync on export too.
Jerry

Audio drops when movie exported from iMovie into iDVD

Hi there,
I am a problem which I can't seem to fix.
I have created a 7 minute long slideshow in imovie with MP3 files from iTtunes embedded. The video and audio are fine when exported as a MOV file (and within iMovie itself). But when exported into iDVD for burning, the audio drops out completely after 3 and a half minutes.
I've tried updating iMovie, iDVD etc., deleting encoded assets as it says to do here: http://support.apple.com/kb/TA24043?viewlocale=en_US
to no avail.
Does anyone have any tips? My friend's wedding is on Saturday!
Thanks so much.
RR

Hi
A. I do not use "Share to iDVD" - BUT "Share to Media Browser" and as Large (not HD or other res.) - Works much better.
B. When did it hang ?
a. On Export from iMovie to iDVD
b. When DVD is played on DVD-Player
If last one - then
• What brand of DVD did You use (Yes it matters)
• What type of DVD
• Free Space on Start-Up hard disk - How much
• Burn speed - did You set down this - I do to x2 or x4
Yours Bengt W

Audio synch problem from 24 to 29.97

I am working for a tv show that is having a major audio synch problem.
We send our mix to an external sound house for our pro-tools mix. They request the file to be 29.97, though our timeline is 24. In turn, we export a 24 time line, re-import to an 29.97 timeline and than re-export at 29.97 with a time code burn. They export the mix, using a sound compressor that converts the mix to a 24 fps synch, we send them a 24 frame export that they can check it againest on their end in Final Cut Pro. For them, both the opening and end two-pop lines up. When we recieve the mix back however, and bring it onto our timeline, it is always 24 frames ahead of the picture. We can't fiugre out why.
I know this all sound very confusing.
Below is our export and timeline settings:
OUR TIME-LINE\EXPORT SETTINGS:
1st Time Line:
FS: 1280x1080
FPS: 24
Compressor: DVCPRO HD 1080i60
Aud Rate: 48.0 KHz
Aud Format: 32-bit Floating Point
1st Export:
FPS: 24
DV\DVCPRO - NTSC
Compressor: DVCPRO HD 1080i60
Aud Rate: 48.0 KHz
Aud Format: 32-bit Floating Point
Data Rate: 2.9MB/sec
2nd Time Line:
FPS: 29.97
Compressor: DV/DVCPRO - NTSC
Aud Rate: 48.0 KHz
Aud Format: 32-bit Floating Point
2nd Export:
FPS: 29.97
Compressor: DV\DVCPRO - NTSC
Aud Rate: 48.0 KHz
Aud Format: 16-bit Integer
Data Rate: 3.6 MB/sec
AUDIO MIX SETTINGS:
Data Rate: 140.6 K/sec
Aud Rate: 48.0 KHz
Aud Format: 24-bit Integer
Total Out: The audio is exactly 24 frames ahead of the video by the end of the clip
We shot on a Panasonic HDX900
Can anybody think why this might be happening?

ProTools mixes 24fps...and 23.98, which SHOULD be the case here. There is NO REASON why they should want a 29.97 mix, nor should they mix at that rate...because you are not working at that rate nor delivering that rate...are you?
Your sequence settings confuse me. DVCPRO HD 1080i60 runs at 59.94. You can get it to 23.98 with a little work...but you indicate 24fps. Is that SOLID 24fps? Not 23.98? If so...that is a major issue. You should not be working at 24fps. 23.98 is the frame rate...
Still...if you are working at 23.98 and delivering a 23.98 master, the audio guy needs to mix at 23.98. ProTools is capable of 23.98. If they can't do that, then I'd suggest finding another mixer.
Shane

AUDIO SYNCH PROBLEMS

I have never had an audio synch problem 'til now. I am running 10.5.7 on a 2.8 GHz Intel Core 2 Duo 4 GB ram, 24" imac.
iMovie 6.0.4
I have a 50 minute heavily edited project with many transitions, etc.. I have no problem with the footage downloaded from my Sony HD camcorder. I even saved many individual frames as pictures and changed them to the beat of the music in the timeline and all worked perfectly. BUT, my problem is with the "video trailers" I slipped into the timeline. The audio slips when I play back in the timeline AND when burned to DVD. BUT, it does not slip in the same place every time I preview it. If I scrub the playhead back over some of the bad scenes and play them again, they are in synch. IT KEEPS CHANGING..... When I export to a desktop movie to review - the synch problem is there and some of the audio is missing. This only happens on "movie trailers" I have downloaded.
I can't figure out why it keeps changing in the timeline and then correcting itself when I back up and play it over again. I AM GOING CRAZY........
Thanks in advance for any suggestions.
Wally

Thanks for the reply but my problem is not with iDVD - it is with iMovie - when I add "trailers" to it they go in and out of synch at different places everytime I review it before moving on. When I scrub back over the problem area and then play again, they are perfect for one time and then I try again and they are not synched. The problem is in iMovie.
Thanks,
Wally

Best method for exporting from iMovie?

I have been having a lot problems with exporting from iMovie. I have a 30 minute movie that I want to compress to a file around 400~500mbs. I found the best results with Divx and .Avi files. Unfortunately, after I installed Tiger, I noticed that the audio was faster than the video, like " old kung-fu movies ".
I read in other forums that there are many problems with Divx compatibilty with Tiger. Whie waiting for a new version of Divx, can anyone give me some advice on the best way to export a movie from iMovie( good audio and video quality) thanks in advance!!

http://www.danslagle.com/mac/iMovie/tips_tricks/6007.shtml

IDVD Stops Responding when Exporting from iMovie

I'm using iDVD and iMovie (from iLife 06 and fully up to date) on a MacPro (also up to date on all software, MacOSX, Quicktime etc).
This proceedure has worked before several times but now results in a non-responding iDVD every time I try it, including an archive and re-install and a complete new install of OSX and all software on a new partition.
What I'm doing.....
[1] Recording a TV programme on EyeTV (410) and exporting it to iMovie - sucessful every time
[2] Edit the iMove project and add chapter markers and save project - no problem.
[3] Export to iDVD - iDVD shows exporting in progress and whilst this is still showing iDVD launches
[4] iDVD starts playing the music from a std theme for a few seconds and then stops. Then resumes the music after resizing the window and then after a couple of more seconds freezes. From the Dock I can see that iMove and iDVD are "not responding"
[5] Eventually iMovie completes it's "export" and then starts responding normally. iDVD continues to show as non responding although I can move the window around the screen. I have to force quit iDVD to get it to close down.
I have tried:
Re-exporting the project from EyeTV
Deleting the preferences files for iMove and iDVD
Deleting the iLife suite and re-installing
Doing an OSX archive and re-install
Installing a fresh OSX (10.4.8) on a different drive and installing fresh software
Running Disk Utility - clean bill of health on both drives
Repaired permissions
The Console reports the following errors when exporting from iMove to iDVD:
===== Tuesday, 24 October 2006 22:56:45 Europe/London =====
[KN,10:57:08:852]/SourceCache/iDVD/iDVD-791/./PBProjects/iDVD/RemoteControlContr oller.m:348 : switchTheme: mIsPlaying = 0
[KN,10:57:08:852]/SourceCache/iDVD/iDVD-791/./PBProjects/iDVD/RemoteControlContr oller.m:348 : switchTheme: mIsPlaying = 1
[KN,10:57:11:968]/SourceCache/iDVD/iDVD-791/./PBProjects/iDVD/RemoteControlContr oller.m:348 : switchTheme: mIsPlaying = 1
2006-10-24 22:57:53.394 iDVD[424] NSExceptionHandler has recorded the following exception:
NSInvalidArgumentException -- * -[NSCFArray addObject:]: attempt to insert nil
Stack trace: 0x954ee243 0x9264f2cb 0x9264f110 0x925dd399 0x000df708 0x000df806 0x00215e6d 0x002167ef 0x0021470b 0x001a0b4f 0x00184105 0x92627d78 0x92627222 0x92626fa9 0x92626811 0x92621ae0 0x00166dc7 0x9261e861 0x925f2ef1 0x925f2d1b 0x9151d6c5 0x9151d5f6 0x9151d4c2 0x92dda340 0x9325c63d 0x9325c056 0x93255ddb 0x93249d2f 0x0000ad5d 0x0000ab36 0x0000aa51 0x00000002
Result - problem persists. I'm at a loss as what to do next. Any suggestions greatfully received.

Yes, tried that when I deleted the preferences. Disk Utility did not report any permissions needed repairing.
What really mystifies me is that this export to iDVD did work once and I expected it to resume once I'd created a fresh OSX install along with all the iLife apps on a new partition, but it remained the same!
Perhaps there is some sort of other software conflict going on? I have Adobe CS2, MS Office, Toast and FMP installed all are latest editions. On the utilities front I have installed Stuffit Deluxe, Internet Cleanup, Contour USB controller for video editing and a LogicTech wireless trackball. Again all the drivers are the latest releases.
Does anyone know if there are any preferences associated with the other not responding applications listed in my other post that I could try the delete-reboot trick on?

How do I export from IMovie when "not enough room in Heap Zone" error code appears? How can I correct, what to Do.."export movie" insteand of Media browser or IDVD? Finalize movie? I want to burn it to DVD!

How do I export from IMovie to Wondershare Creator to Make DVD and share hour long movie when I am unable to "publish" movie on Media Browser of IDVD because the error code "not enough room in heap Zone/ " appears and function is aborted.
I shortened the movie, that is no cure...Correcting date info on clips does not pertain. Why would Apple throw roadblocks in your way without solving problems they create?
A techie made an appointment on the phone and was totally incapable of addressing the problem.
What is a heap zone????

Instead of Share to Media Browser, what happens if you try Share Menu > Export Movie... (choose Large size) and save it to the Desktop?
If that fails try Share Menu > Export using QuickTime...
Then pick Movie to QuickTime Movie, then click on Options... which is just to the right of Export
Under the Video section click on Settings...
Then in the pulldown menu at the top, titled Compression Type: Choose Apple Intermediate Codec. Then click OK. And click OK again, and save it to the desktop. Once the .mov file is created, you can import that into iDVD and most likely it will work in Wondershare Creator if you prefer to use that instead.

Quick Question (re:exporting from iMovie into iDVD)

Hello everyone!
I just have a quick question for you all... (I want to see if this is normal - I'm on a deadline and this is kind of freaking me out)
So, we have a 20 minute or so video in iDVD. It plays fine, etc etc. The goal is to burn it to a DVD.
I used the "Export -> to iDVD" function in iMovie, which launched iDVD.
But here is the weird thing: nothing comes up in iDVD. It doesn't make a new file, doesn't give me anything... it is just open, waiting for me to create a new project to work with.
YET, if I look in the Activity Monitor, I do see that EncoderServer (using 123% CPU) and ThumbnailServer (both iDVD processes) are running.... but shouldn't iDVD have told me it is working or that it is dealing with data?
This is very un-"apple". I totally would have expected a progress bar of some sort in iDVD telling me it is working or something.... or is something wrong and I should try to export it in a different way?
(I guess the underlying question is: when you export from iMovie to iDVD, does iDVD normally give you any 'heads-up' that it is working? how long does it normally take to open the project in iDVD?)

Hi Matt!
when you export from iMovie to iDVD, does iDVD normally give you any 'heads-up' that it is working? how long does it normally take to open the project in iDVD?)
Yes, and it's instant.
What you should see is iDVD opening and asking you to create a new project, It will suggest naming it the same as the iMovie project.
There are reports that exporting from Imovie to iDVD can produce problems. What I do is save the iMovie project and close iMovie. Open iDVD, create the new DVD project, then go the File menu in iDVD, scroll down to Import, and in the side menu select Video. This open your Movie Folder, wherein resides your iMovie project. Select it and it imports into iDVD in a flash.
Remember: iMovie projects go in the Movies Folder, iDVD projects go in the Documents folder. Change that, and they get very confused and unhappy.

When I try to export from iMovie '11 I get repeated messages that the project is too big. Why? Is there a workaround? (I have already cut a 40-minute movie into three chunks...)

When I try to export from iMovie '11 I get repeated messages that the project is too big. Why? Is there a workaround? (I have already cut a 40-minute movie into three chunks... the first exported to iDVD ok, but the next one of 15 minutes balked for the same reason -- too long...)

I wish I had a mac :-P
Sadly, this is Windows machine so I dont have a non-iOS version of iMovie. I have 2 ideas left. The first is xfering the project to my iPhone 4 and trying to export it there (if that works, awesome but geez apple the iPad 2 is way more powerful than the iphone 4.. youd think I wouldnt even have to attempt this). The 2nd idea is to start at the end of my movie and delete clips and sounds backwards, trying to export each time to find whatever clip is causing the issue (when the movie was 5 minutes it mixed no probem, so I only need to go that far).
Wish me luck?
Also, is anyone else besides me and the 5 dudes in the other threads having this issue?? Speak up, guys - Apple cant a fix a problem they dont know about.

Audio synch problem

I have a 1 1/2 hr program in HDV that I'm having audio synch problems with during export. All my frame rates for my clips are the same as well as my audio sampling rates. It will start fine, then be slightly off and by the end of the program that audio is behind by about 3 seconds. I've tried all formats, reference file, self-contained, Anamorphic DV and still no luck. Any ideas?

Exporting Quicktime movie...current settings, video and audio....just uncompressed right out of FCP.

How to sync sound with movie when exporting from iMovie

i have problems with sound synchronization with movie. mostly is movie delayed few seconds behind sound. also sound is repeatedly missing - under certain frequency. videos are prepared in iMac iMovie and exported in to the file and stored on synology. how to fix this trouble before exporting from iMovie?
playing movie on imac works without problem

I have a collection of Apple Support documents about passwords, some of which might be of help ...
iOS: Forgot Passcode or Device Disabled
http://support.apple.com/kb/ht1212
iOS Passcodes
http://support.apple.com/kb/ht4113
Find My iPhone, iPad, iPod a Touch or Mac
https://www.apple.com/support/icloud/find-my-device/
Find My iPhone Activation Lock
http://support.apple.com/kb/HT5818
Find My iPhone Activation Lock: Removing a Device from a Previous Owner's Account
http://support.apple.com/kb/ts4515
Apple release Tool to check the Activation Lock Status of iOS Devices
http://www.idownloadblog.com/2014/10/01/activation-lock-status-check/

No sound when exporting from imovie 3,03

After having read most of the posts related to sound troubles, I still can't figure out why I can't get any sound when I export from imovie 3,03.
I almost know the entire dan slagle site, and checked every button to play with, I've tried many export or preferences settings (including various depths or rates) but got no result at all.
Surprisingly, when I grab the .mov file to some converters (ffmpegx), the expected audio part looks to be there, but remains silent (for me, meaning all of the bits at 0).
Don't hesitate to require additional info - thanks to prompt answers
G5 2xPPC Mac OS X (10.3.9)

hurrah !
i just downgraded QT 7.x to 6.5.2 and it worked fine at last.
From the informations I've gathered, DO NOT RUN QT 7.x WITH OSX 10.3.9
For those who would follow the appropriate steps to get rid of v7, go to : http://fox-gieg.com/tutorials/2005/undo-quicktime-7/
and don't miss : http://www.charlessoft.com/
Thanks a lot to Brie Fly for its so helpful comments.

Changing frame rate when exporting from iMovie '09 using quicktime has no impact on duration. Why?

Changing frame rate when exporting from iMovie '09 using quicktime has no impact on duration. Why?
I have a file created by digitizing an 8mm film at a rate of 24 fps. I would like to create a downloaded movie at a frame rate of 15 fps. The Export using Quicktime option seems to provide that capability but the resulting file has the same duration as the original 24 fps file. How can I get the exported movie to be slowed down?

joegez,
There is a feature you can use to slow down the video. In the project, move the mouse pointer over the clip, then click the gear icon. That brings up the Inspector. Click the Clip tab. Then you will see a feature there called Speed. Move the slider to the left to slow down the clip. Or you can enter a percentage in the box on the right.
Hope this solves the problem for you.

Idvd pixelated when exported from imovie

DVD looks great on imac but dvd is pixelated once exported from imovie and put on dvd using IDVD.
Any suggestions

Welcome to the forums, Alison.
I'm not a GarageBand user, but couldn't you export the GB audio tracks as a Quicktime file, and then import that audio track into iMovie? If it's combined in iMovie, then it should import into iDVD without a conceptual hitch.
John

Audio Synch Problem Exporting From imovie 6

Similar Messages

Maybe you are looking for