Audio track recording with 2 MIDI devices on Channel Spitter

I now have a turn table set running through XLR cables into an M-Audio interface, and than into a USB Hub which runs into the MacG5.
I've got the Channel Splitter Track hooked up, and I am now tryin to record 2 MIDI Devices and an Audio track (from turntables) at the same time. Is this possible ?
I've gone into the Audio Drivers and Hardware window and messed around but with no success. Do you have any advice for me ?
I am very new to this so step by step would help alot. Thankyou.

I've tried that, and what happens is the Instr track is picked up and recorded but I'm getting nothing from the audio track.
It seems that the Logic wants to read the devices one at a time. Meaning, I can get it to read the audio interface but not the Midi, or the Midi and no audio. It will not read both at the same time. ( when Logic is picking up the audio interface I can see that it's getting a signal from my midi devices but I'm getting no sound, and nothing is being recorded from the midi devices).
I have a feeling that I've done something wrong in the Audio Hardware and Drivers window.
Thankyou again for your time, I'm detirmined to learn this system. You've been a big help.

Similar Messages

Logic Pro 7 - Audio Track record with Firewire In

System: Mac Book Pro. Logic 7.2.3 M-Audio Firewire 410. Aggregate device created = Firewire Multichannel (as input) & Built-In Output. (Built-in microphone turned off) Using condensor mike connected to F/W interface
SYMPTOM: No Audio being recorded to Audio Track. MIDI interfaces OK.
Any idea how to set Audio track to capture Firewire audio IN? (The set-up works properly with Garage Band)

Have you checked the Audio Input in the Channel Strip? What is it set to? Have you armed the Record button? ... say a bit more about your set up

Hi, I trimmed an audio regin in the audio track edior with "Snap Edits to Zero Crossings" on. But I zoom in.the waveform was not ended at Zero point. Why? In the audio file editork, "Snap Edits to Zero Crossings" option works fine.

Hi,
I trimmed an audio regin in the audio track edior with "Snap Edits to Zero Crossings" on.
But I zoom in、the waveform was not ended at Zero point.
Why?
In the audio file editork, "Snap Edits to Zero Crossings" option works fine.

correction needs to be made to step #14, I typed:
14) Point to the start or end one of the clips, when you see the icon showing arrows going either way, right click and drag your clips to roughly match up with the timeline selection, then zoom in further and adjust the clip start and end points to match up exactly with the timeline selection start and endpoints.
Here is the correction, THE CORRECTED PARTS ARE CAPITALIZED:
14) Point to the start or end OF one of the clips, when you see the icon showing arrows going either way, LEFT-CLICK and drag your clips to roughly match up with the timeline selection, then zoom in further and adjust the clip start and end points to match up exactly with the timeline selection's start and end points.
Another Correction:
Originally read:
Addendum: IF you have 2 files selected and click "Edit" to go to Edit view, it will give you the file of the clip you selected first, not 2nd. You must then go back to MT view, de-select the clip you selected first, then de-select the clip you want to edit, then RE-select the clip you want to edit.
Here is the the correction, CORRECTED PARTS ARE CAPITALIZED:
Addendum: IF you have 2 files selected and click "Edit" to go to Edit view, it will give you the file of the clip you selected first, not 2nd. IF YOU WANT TO EDIT THE 2ND FILE YOU SELECTED IN MULTI-TRACK VIEW, You must go back to Multi-track view, de-select the clip you selected first, then de-select the clip you want to edit, then RE-select the clip you want to edit, THEN CLICK "EDIT" TO GO TO EDIT VIEW.

Audio Track Recording (Armed) button plays a midi sound when it flashes red

Hard to explain but when I click the "R" Record/arm button on an Audio track it makes a sound through my midi device (my keyboard) in time to the flashing of the red light.
I've just installed an RME Fireface 800 and I'm using the MIDI interface to connect this to my keyboard and use through Logic
Does anyone know how to turn this off? When I actually start recording it eventually turns itself off, so it only happens when I arm the track.

it sounds like logic is trying to send midi to a control surface telling it to display the record light. I'd check in the control surface setup window and see what's there.

Track levels automatically max out with midi devices since update

Hello,
Since the last mountain lion update, I've had problems with USB midi inputs via USB on my 2011 MacBook air. Specifically, the volume level on each track will automatically go to the max volume setting and cannot be adjusted if I plug in a midi device.
So if I have one track that is a midi keyboard and another track that is a guitar, the tracks will allow me to play at the volume I set for a few seconds, then the track volume slider will go to max on its own.
Once I unplug the midi device, the track volume goes back to normal.

Hi DaniBCN
What versions of software are you using? LabVIEW 8 but what about NI-VISA? . You can download the lastest versions from ww.ni.com/downloads.
What scope are you using? What bus (GPIB, ENET, USB)? Here is a great resource to comunicate with tek scopes
http://digital.ni.com/public.nsf/websearch/202E14463D2D819F86256C39005D7828?OpenDocument
I know NI has a great relationship with tektronics (tek has a LV version inside the open scopes, NI has develop a specific version of SignalExpress for Tek scopes)
Hope it helps.
Javier Gutiérrez
NI Aplication Engineering

Midi instrument to audio track recording prob.

Im Trying to record a midi (instrument) track to an audio track. I have created the sound using the FM8 synth... There is one parameter on FM8 that wont record automation (morph grid) so to get the effect I need to record it in as a real audio file. So I bus the instrument track out to bus 1, then i take the audio track and make that audio bus 1... levels seem to come up yet for some reason when i record it doesnt record anything despite there seeming to be a level coming up.. any suggestions? Ive been searching the manual for hours

I was afraid that was the case...Thankyou for taking note of the performance issue and answering my real question, cuz i have an automation problem which im told is a bug and have a work around for now but still no live automation and if i do live auto. it will record it but i cant hear any of the old automation as im doing it making it kinda useless at many times... but anyways.... so it appears as my two options are to re-route it out externally (but then wont that still only leave me one real pass of automation via midi) cuz if i am still able to modulate the regular audio via live in on the synth using the audio... then that would work... but Im still not sure if i would be able to record the audio file on a midi track (ill have to try that unless someone knows)... if that were the case then i could just bounce the file to audio and modulate everything using the synths as effects?? do you know if they can do that on Native instrument synths?

PROBLEM AXIOM AIR 61 IN LOGIC, DON'T REPRODUCE SOMETIMES THE TRACK RECORDED WITH AXIOM AIR 61

I have some problems working on LogicX, cuz when i play the track that i recorded with the AXIOM AIR 61, sometimes don't sound nothing, and then when i put play again it sound the track, the think is that the LogicX. I don't know if it's a driver problem o something like that. Need Help Urgent!

Folks.... I eventually solved the problem so if anyone else is interested here is the solution.
The Axiom DirectLink for Logic/Garage band: Axiom_DirectLink_For_Logic_OSX_1_0_0-3.dmg
Should install a file called Axiom.bundle in the directory
MacintoshHD/Library/Application Support/MIDI Device Plug-ins/Axiom.bundle
In my case (see above) the file had successfully installed to that location. However, for some peculiar reason the permissions on the folder had been changed - current admin and users could not read or write. I have no idea how that happened. In any event, despite the fact that the file had been installed, when Logic was opened I was unable to see the Axiom as an available control surface to install.
I reset the permissions and the problem was solved!
It's only taken me a week to get there but now happy that it's OK. The Axiom612 isn't cheap!
I hope this helps someone else.

Unable to perform multi audio tracks mixing with Audio Mixer

How do you get a simple multi track mix with the Premier Pro 1.5 Audio Mixer?
I got 2 audio clips, each sitting at the start of its own separate track (Audio 1 and Audio 2). I just want to mix them into the Master track. Simple enough.
So I go to the Audio Mixer. Position the CTI at the start of the tracks and hit the red RECORD button. The red spot starts blinking. Then I hit the START/STOP button expecting the tracks to start mixing into the Master track. Instead, I get this error message
"PLAYER ERROR: You cannot record without enabling at least one track for recording."
I get the same problem if I try the mix onto a submix track.
What am I missing? I combed through the Premiere Pro User Guide and J. Rosenberg's Premiere Pro Studio Techniques but to no avail.
Thanks for any help.
JB.

Jacques, I havn't seen 1.5 for a while, so I need to stress that what I'm about to say is more of an educated guess linked to a rough memory.
Each audio track in the mixer has a small chip (tickbox in 1.5??) that you click in order to enable that track for recording. In CS3 it's a little microphone.
Having said that, I DON'T think that's going to give you what you want, as the intention of the recording functionality in PP is to record audio FROM AN EXTERNAL SOURCE (like a microphone) straight to an audio track, say, when doing a Voice Over for some video.
You can't "mix down" to the master, as the master is not a track per se. It's just a "final" level control. The master will always be the sum of the active tracks, and THAT'S what will be rendered in the final output.
You can still "live mix" your audio with the faders, it's just that those movements get recorded as keyframes on each of the tracks you modify (including, BTW, the Master).
The advantage to this workflow is that every fader move you make is infinitley editable... a small error when riding the faders can easily be fixed by dragging keyframes.
HTH.
Matthew

Multi-track recording with GB1 and GB2

I recently purchased a new RME Fireface 800 and want to begin recording multi-track audio.
I plan to purchase DP in the future but have spent my $ allocation for now and want to be able to at least get started using something simple and cheap like GB. I currently have GB1 and have learned from experience that it does not support multi-track recording. If GB2 does I will UG.
Has anyone successfully recorded 8 tracks simultaneously with GB2 and if so how?
soundegr7

I finally got around to fixing a typo in the anchor for the above link, but instead of adding it, i replaced the typo which breaks the above link. The correct (and hopefully final) URL is:
http://thehangtime.com/gb/gbfaq2.html#recordmultipletracks

Audio track from EXTERNAL midi

Hi,
Logic 9 doesn't seem to allow me to create an audio track from an External midi instrument. If I'm wrong, how do I accomplish the task?

Hi Spheric, and thanks for your input.
It seems that Logic 9 treats External midi and Internal midi differently. I brought this up at a One-to-One session and
1) we had to change Preferences/Audio/to "Slow (CPU saving) in order to Solo the external midi track, and
2) the track would not transfer to the Audio track that I set up, even at this slower CPU setting.
I've read other complaints about this on the Net - but with no answer yet.
I appreciate your getting back to me,
Paulie too

No Audio when recording with built -in mic

i have used imovie HD for a while no and when i record with my macbook, it makes perfect video with sound. i have just done my first recording with imovie '08 and there is no sound at all. my setting are set to internal mic. is there something special i have to do to make it record both sound and audio?
please help. i have recorded about an hour of work for future keynote presentations and would be destroyed if i had to remember everything i came up with.

how do you do it?
1. Create a New Basic Track
2. Click the record button
3. There is no step 3.

Using a 4 track recorde with Garageband

I am new to this so forgive me if this sounds stupid.
I have a Yamaha, Mini-disc 4-track recorder. It has MIDI in/out and I have a MIDIsport 1x1 MIDI to USB cable. Is there anyway to send the MIDI signal to garage band or what should I do. I am doing vocal recording only and would like to use My MD 4-tr. recorder. Can these two be used together or is my attempt futile. Thanks

MIDI is not audio, so no.
If your Mac has a Line In, you could use a Line-Out from the 1/4 track recorder which will let you record a stereo track at a time in GarageBand.
--HangTime [Will Compute for Food] B-)>

Imac g5 with midi devices

How would you go about connecting a midi device to an imac g5?
What equipment is neccessary?

which would be the best for midi? and audio output to monitor speakers?
M-Audio iControl USB Controller for GarageBand
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/72403/wo/Q13RkLI ojfGG3PujURFAHQzvbMx/9.SLID?mco=7FC1BF3B&nplm=TC834LL%2FA
M-Audio MobilePre USB Audio Interface
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/72403/wo/Q13RkLI ojfGG3PujURFAHQzvbMx/7.SLID?mco=E0FBA344&nplm=T9104LL%2FA
or
M-Audio FastTrack Recording Interface
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/72403/wo/Q13RkLI ojfGG3PujURFAHQzvbMx/7.SLID?mco=7936F36F&nplm=TB084LL%2FA

Audio stream recorder with Audigy 2 Plati

I have never been able to get the audio stream recorder to work. I've used creative's online update, so everything is current, but when I tell the stream recorder to update the content directory, it just tells me the update failed. I've never been able to use this thing as it's never downloaded any content. I've also pasted in the URL to the stream I'm trying to record, but it doesn't work. Any advice?

I found the information I was looking for, apparently the server service Creative was using shut down, and though the stream recorder was a component advertised with this line, they never came up with a replacement. It is unfortunate that this is the kind of support I've come to expect from Creative.

Distorted audio while recording with ScreenSflow

Hi all,
when I record my screen using ScreenFlow (latest version) I get distorted audio.
I am not using external speakers and I just need to record with the "Record Computer Audio" option and nothing else selected.
How do I fix this? It makes it unusuable...
Thanks

You can connect a mic to the iPod via the headphone jack and that mic will be used by the video app you use for the video camera on the iPod. I do not remember if the built-in mic gets cut off when yo do that so you may have to cover the mic hole on the iPod.

Audio track recording with 2 MIDI devices on Channel Spitter

Similar Messages

Maybe you are looking for