Audition does not play nor record

Auditon CS6 does not play nor record.
I can click into the file but when I press play or space there is no reaction. "no transport".
I have uninstalled and reinstalled the program. No luck.
Earlier the onboard processor hat to be replaced (hp warranty). Could it be that this has caused Audition to react strangely. Maybe due to a processor id not being equal to the original setup?
Windows 7 Pro, SP1, HP Workstation Z620 64Bit

When Audition's transport doesn't work, it's because it has become disconnected from your sound device. Go into Preferences > Hardware setup, and reconnect it! Should all work fine then, assuming that your sound device is actually okay...

Similar Messages

Audition does not play sound

Hello to everybody,
the following problem occurs:
after transferring the whole Macsystem (MBP 2010) to a new model (MBP2014) I have a problem using Adobe Audition. It does not play any sound, when starting a window tells me, that some hardware has changed, audio channel assignment says unknown... the audio devices are found..
btw: Adobe Premiere does work, it plays the video as well as the audio. I already killed Audition and re-installed it... but no changes, what can I do?
Thanks for any ideas.
Arne

Ask in the AU forum and be much more specific, beginning with what version you actually use.
Mylenium

My iMovie voice recording is suddenly not working. As I record, it shows the green bars; however, when I play the recording it does not play my voice over at all nor show the green bars. I was mid-way through my project when this problem occured.

As I record, it shows the green bars; however, when I play the recording it does not play my voice over at all nor show the green bars. I was mid-way through my project when this problem occured. HELP!!!!

As far as I can see, it's random. Everything. Nothing makes any sense!
A the moment, the iPhone is playing music with the SIM card, but without anything plugged into it, but it's occasionally fading in and out.
Oh, and I doubt this is related, but about two months ago the iPhone failed to show that the battery was draining - it was stuck at 100%. This went on for a few days, it wouldn't even warn me at the 20% mark, it would just shut off. This happened for at least three full charges - I remember at one point it suddenly started working again at about the 70% mark, I'm not sure if it was alright after that or if it went glitchy on the next charge... but in any case, the problem mysteriously never reappeared after those few days.
Message was edited by: Shiranai

Lync recording does not play

Hi there,
I tried to record a meeting using Microsoft Lync 2013. The file was moved from its default location to a different computer but it could not play. I tried to play it again in the original location but it does not play in any media player.
I have a backup of the recorded file. Could someone help me in how recorded file can be played back?
Many thanks for your kind assistance.
Fekadu

Hi,
Was the issue about file couldn’t be open or the recording could be open but with issue (such as without voice or no content)?
You can try to use Microsoft Lync Recording Manager, click the item and click Publish. Then try to open it with Microsoft Lync Recording Manager to check the issue again.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

TS1424 Purchased an album one or more records does not play all the way through. A 13 minute track only plays for the first 3.05 minutes and then stops and the program locks up. Larry

I just purchased a album and one or more of the tracks does not play all the way through. One track which is a 13 minute track will only play for the first 3 minutes. Larry

Delete the songs from your iTunes library and redownload them by clicking "Purchased", under Quick Links at the top right of the iTunes store.
Download past purchases:
http://support.apple.com/kb/HT2519
If this doesn't work contact iTunes support here:
http://www.apple.com/support/itunes/contact/

Macbook Pro does not play audio part of video

Hi,
I have a Macbook Pro (early 2013 with OS 10.10.1).
A colleague sent me a video file, which was originally recorded in MTS format. The sound portion of it does not play on my machine, although it generally can handle MTS. I have a colleague with a Windows PC, for him the audio plays ok. I have another colleague with an older MBP, for him the audio also plays ok. But then I have two more colleagues with a newer MBP like me, and for none of us the audio plays at all. The strange thing is that I can open the file in various editors such as Premiere, Audition, or Logic Pro, and they would all show the waveform of the audio, even the VU meters react normally, but there still is no audible sound.
On the machines that play the sound, we have tried converting the video and exporting the audio portion into various other formats, but with the very same result. None of them play sound for me. This is extremely weird and we have no answer what could be the problem.
Any help would be very much appreciated.
Thanks a lot & best regards,
Rainer

Hi Eric,
thanks for the reply.
As I said, we had tried several editors and players, as well as all kinds of formats, using all kinds of converters, but so far to no avail.
The AAC codec is a common codec for the Mac, so there should be no need to convert it. I have videos with that codec that play ok. It already turned out that converting the video file to other formats does not make any difference.
But thanks anyway,
Rainer

CS6 does not play the sound

Hi, I bought CS6 some months ago, tried it briefly and it worked. Now, half a year later, I really want to work it, but it does not play, neither mp3 nor wav-files. I see the waveform, I can amplify it, cut parts of it, edit it otherwise, but the red lline and the yellow cursor do not start/move and I hear nothing. I clicked on the start btton and on the endless button, nothing happened. I am using Windows 8.1. Please, help....

Invariably, when Audition's transport doesn't start it's because you've lost the connection to your sound device. So go to the Preferences menu and Hardware setup, and re-establish it - you should be good to go then.

ITunes player does not play songs since upgrading to 10.5.1; not fixed with 10.5.2 upgrade. What now?

After upgrading iTunes on my laptop to version 10.5.1, my player will NOT play any songs. My Library seems intact and no songs appear to be missing, but no song will play --not a song downloaded from iTunes Store, nor a song downloaded from a CD. I was hoping version 10.5.2 would fix this, but apparently not. Still not working. Songs do play on my iPod and on my iPhone and I can transfer songs from my laptop to my devices; I can also download Apps to my laptop through the iTunes Store, etc.--all other functions of iTunes seem to be okay, only the player is not working. (My laptop is an hp Probook with Intel i5 chip, Windows 7 Pro OS.)

Does it look like the song is playing at the top of iTunes? Can you see the timer moving?
Also, make sure the volume slider isn't all the way to the left (mute).
This Apple document may help too -> iTunes and QuickTime for Windows: Audio does not play or plays incorrectly

Safari Does Not Play Youtube Videos

Hi,
I updated safari to the latest version (6.1.2) on my MacBook Pro (10.7.5) and now it does not play any Youtube videos at all. All I get is a black space instead of a video - neither video nor audio.
Does anyone know how to resolve the issue?
Best,
maybug

Go step by step and test.
1. System Preferences > Other/ Flash Player > Advanced > Delete All
     Press the "Delete All" button
     Install Adobe Flash Player.
    http://get.adobe.com/flashplayer/
    Follow the prompts. Quit Safari.
    Restart computer. Relaunch Safari.
2. Allow Plug-ins
    Safari > Preferences > Security
    Internet Plug-ins > "Allow plug-ins"
    Enable it.
    Press " Manage Website Settings" button for more options.
3. Check whether you are currently in YouTube HTML 5 trial.
     http://www.youtube.com/html5
    At the bottom left of the page uncheck the box beside
   "You are currently in the HTML5 trial".
4. Reset Safari.
    Click Safari in the menu bar.
    From the drop down select "Reset Safari".
    Uncheck the boxes beside all items.
    Check the box beside "Remove all website data".
    Click "Reset".
5. Turn off Extensions, if any.
    Safari > Preferences > Extensions
     Now try YouTube.
Best.

Audition does not playback

Hello,
Suddenly audition (5.5 CS built 1815) does not play any tracks anymore. I treid my best but can not find the problem. I removed it and reinstalled the whole product again.
I can load an mp3, and the waveform is showing up in the editor. When I push the play button in the transportscreen nothing is happening. The markerline doen not move and when I drag it along the waveform manualy there is no sound from my speakers (my soundcard is working, a radiostream works fine).
One thing that noticed me is that at the lower hand corner, where playing is displayed, there ie a message but it is showing so shortly that I can not read it.
Can anybody help me wit this.
Thanks in advance!
André
WerkenFM
The Netherlands

Hello One_L,
Thanks for your reply. I found the solution to my problem myself... Had to buy a new pc to find it because it gave the same error on a new one after changing the audio output wires..... It was in the setup routing the correct audio channesl to the output. After that is start playing immediately.
André

24 fps video does not play in CS5.5 source monitor without choppy motion

Problem: 24 fps video does not play in CS5.5 source monitor without choppy motion. 30 frame will play fine. I took the same 24fps shot, using the exact same setup parameters, and played it in my CS5.0. No problem. I did them side by side and checked to make sure everything was EXACLTY the same. The 24fps shot played smoothly in the CS5.0 source monitor. Can anyone tell me what the solution might be to get the CS5.5 to play smoothly? When I rendered it on the timeline in CS5.5 it played smoothly on the timeline. Perplexed.

Thanks Tood,
Here's the other info. I am running CS5.5 on a windows 7 ultimate 64bit (service pack 1) OS. All of the recent updates have been installed on both the OS and the CS5.5. The source footage is H.264.mov from a nikon d7000 at 1080p 24fps. My video card is an Nvida GeForce GTX285. My processor is an Intel Core i7 3.33GHz with 12GB ram. I am running no third party codecs or effects. I am using the Mercury Playback engine GPU accelerator. I am using a DSLR24 frame project setting.
Here is the problem: When I bring a 1920x1080 24fps.mov file into my DSLR24 frame project, or any project setting, in my CS5.5 and open it in the source monitor it plays as if it is trying to catch up; stuttering and skipping; it plays the same on the sequence timeline until I render it. I get no error messages. When I bring the exact same file into my CS5.0, with the exact same project settings, it plays perfectly in the source monitor and on the timeline without rendering. When I bring in a 1280x720 24fps.mov or any other size file into my CS5.5 in any project configuration, it plays perfectly smoothly. Everything plays smoothly without renedering in the source monitors of my CS5.0 and CS5.5 except for a 1920x1080 24fps.mov file in CS5.5. The exact one that I need to play there.
I would have no problem cutting in my CS5.0 if it intergrated with audition; which is why I bought the CS5.5.
Thanks,

Premiere Pro CS6 and Audition CS6 not playing any media

I'm having a problem with both Premiere pro and Audition CS6 not playing back any media when I hit play. The play button shows that it should be playing back but the playhead doesn't move at all. I'm on a late 2011 Macbook Pro running Mountain Lion 10.8.2 with 16gb RAM and an SSD. I've already completely uninstalled and reinstalled both application multiple times to try to get this working. Any help would be greatly appreciated.

1st, More information needed for someone to help... please click these links and provide the requested information
-http://forums.adobe.com/message/4200840
-http://forums.adobe.com/thread/416679
-http://forums.adobe.com/thread/419406
2nd, What are you editing, and does your project match your video?
Read Bill Hunt on a file type as WRAPPER http://forums.adobe.com/thread/440037
What is a CODEC... a Primer http://forums.adobe.com/thread/546811
What CODEC is INSIDE that file? http://forums.adobe.com/thread/440037
Report back with the codec details of your file, use the programs below... a screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30
For PC http://mediainfo.sourceforge.net/en or http://www.headbands.com/gspot/
3rd, Please NOTE that the PPro CS6 screen may look a bit different (I use CS5)
For CS5 and later, the easy way to insure that your video and your project match
See 2nd post for picture of NEW ITEM process http://forums.adobe.com/thread/872666
-and a FAQ on sequence setting http://forums.adobe.com/message/3804341

This disc can be neither played nor recorded

I'm working on an HD project for the first time in DVD Studio Pro and every disc I burn is rejected by my Sony DVD Player/Recorder with a message saying "This disc can be neither played nor recorded." I've done several projects in SD and never had a problem. The same DVDs play fine on my MacBook Pro and look great.
I've used the same source file from Final Cut Pro to burn a disc in iDVD and that does play on the Sony DVD deck, however the quality isn't great. The image has some jaggies. Those jaggies are also present when played on my laptop's DVD player. In contrast, discs burned using DVD Studio Pro look great on the laptop. Very clean. They just won't play in the DVD deck.
The project was shot using DVCPRO HD 1080i60. I'm burning on my laptop's Super Drive. Below are the Preference settings I'm using (at least the ones that seem relevant to HD).
Project
DVD Standard: HD DVD
General
SD DVD Menus, Tracks, and Slideshows > Display Mode: 16:9 Letterbox
HD DVD Menus, Tracks, and Slideshows > Resolution: 1920 x 1080i / Display Mode: 16:9 Letterbox
Simulator
Playback Output > Resolution: HD 1080 / Display Mode: 16:9
Encoding
Field Order: Auto
Bit Rate: 18.0 Mbps
Max Bit Rate: 27.0
Any help would be appreciated. Thanks much --
Dan

Oh for crying out.... Yep, you're right. Well, that was unbelievably easy (and stupid) to resolve.
Thanks for your help!

Missing file -- can't find -- see it but does not play -- what went wrong?

I was working on a 2 hour long podcast using 1 track - female voice. When I opened the file, the 1st hour does not play. Get a message saying "missing file." I searched for the file on all disks in all folders -- not there. But you can see the recorded track -- it just says it's missing. The 2nd hour is fine. I have no idea what could have gone wrong. That's a lot of lost work. Any ideas? Thanks.

trying to figure out a recipe for a problem is really good, so congrats on taking the extra step (i wish more people would list their steps, it would make diagnosing problems a lot easier)! unfortunately, no, that should not have caused a problem, it SHOULD have worked as you expected. changing settings, or moving regions between tracks should not cause a problem.
stopped and changed to plain Female voice to be consistent with my other podcasts.
just for future reference, you don't need to worry about that:
http://www.bulletsandbones.com/GB/GBFAQ.html#nondestructive
(Let the page FULLY load. The link to your answer is at the top of your screen)

The music I buy in the Iphone does not play in itunes

When I buy music on my Iphone 4 and then sync with Itunes on my PC, the songs appear in the list but does not play. and then some songs on my Iphone 4 does not play properly or play other song. what is wrong?

iTunes: How to move [or copy] your music [library] to a new computer [or another drive] - http://support.apple.com/kb/HT4527 - a somewhat bewildering and not always easily understandable set of options.
Quick answer if you use iTunes' default preferences settings: Copy the entire iTunes folder (and in doing so all its subfolders and files) intact to the other drive. Open iTunes and immediately hold down the Option (alt) key (shift on Windows), then guide it to the iTunes Library.itl file in the moved iTunes folder.
For the record there's this reference for iTunes 11 but it really doesn't strike me as having the specifics you need. iTunes 11 for Mac: Move your library to another computer - http://support.apple.com/kb/PH12168
Windows users see tip at: https://discussions.apple.com/message/18879381
2011 Transferring your iTunes library - http://www.ilounge.com/index.php/articles/comments/moving-your-itunes-library-to -a-new-hard-drive/ - An article with good background information, particularly if you are not sure your media files are all grouped for quick solution above. Unfortunately it uses the single term "transferring library" for two very different moves; relocating just your media (not recommended unless you really need this configuration) and relocating media+database (really your whole "library"). Make sure you understand the difference before electing to move only media.
If you put it in the default location of Macintosh HD > Users > *User Name* > Music then you don't even need to start with the option key held down, iTunes will automatically look for it there. (Make sure there isn't anything already in the iTunes folder there that you want to keep since you will be replacing it with the one you are moving.)

Audition does not play nor record

Similar Messages

Maybe you are looking for