Authenticating / obtaining IP from Hub3
Until recently - no problems
Now HTC Wildfire repeatedly fails to obtain IP address from Hub 3
Also found my HP wireless printer cannot connect
Laptop sometimes works fine - sometimes 'unknown local connection'
Found by trial & error switching hub off / on works (hence this message)
Would using the small Reset button provide a better solution ?
Think I saw someone else had similar issue some time ago so don't know if this is a common condition
Any comments welcome
(I get frustrated easily so I might find the answer myself once I calm down)
Try a factory reset of the homehub by pressing a pin into the recess button on the rear for about 20 seconds. This can often sort out configuration problems.
Similar Messages
-
Adobe Bridge CC cannot obtain files from this device.
I am getting this error message when I attempt to upload videos to my Mac from my Canon 7D:
Adobe Bridge CC cannot obtain files from this device. Please be sure the device is properly plugged in and the battery is full charged.
Battery is full charged and camera is connected properly. I have restarted the camera, Bridge, and the computer as well. I tried reinstalling Bridge and it allowed me to upload 3 of the video files. Then the error message came back. There were a few RAW images on the camera that I was able to upload, but when I tried the video again I got the error message. I read a post about renaming the folder that you are saving to as a fix. I tried that as well, but it did not work.
Any help would be greatly appreciated! Thanks!
-JThis excerpt is from a long-gone post by author Bruce Fraser:
Bruce Fraser - 4:17pm Jun 14, 04 PST (#5 of 21) Opening files directly from the camera is a bad idea for a variety of reasons*, and it most certainly isn't faster than using a FireWire or USB2 card reader.
• Drains the camera battery
• Runs the risk of the software you're using to open the images writing to the card and destroying the format
• Runs a small but significant risk of USB power frying the camera
• runs the risk of wearing out the camera's connector,
• Slowest method known to mankind of getting images off a CF or SD card -
Adobe Bridge cs5 cannot obtain files from this device.
I download photos to my computer using a Kingston downloading device.
Since installing Mavericks the above message comes up and will not carry out the download.
Is this a known problem with Mavericks and is there a remedy?
I would say that using the same device my photos download perfectly on my MacBook Pro.
Messages
1. Adobe Bridge CS5.1 cannot obtain files from this device.
Please ensure that the device is connected properly and that the battery is charged and try again.
2.I also get a message telling me that the "disk was not ejected propery" which is not the case.Thanks Eric
The MacBook Pro is not running Mavericks and sorry about the double post.
I have actually solved the problem and the answer might be of use to others with the same problem.
There is a firmware update that will correct the problem.
It's at
http://www.kingston.com/en/support/technical/products?model=fcr-hs3
There is a small catch in that the firmware update can only be done on a Windows machine but I have been told that once this is done it can be used with OSX9 .I have just done the download but I haven't checked this out yet. -
Obtaining DataSource from Application Module
How may i obtain DataSource from pool managed by Application Module? I want some of my db-related operation performed by Spring's JdbcOperations class ( http://www.springframework.org/docs/api/org/springframework/jdbc/core/JdbcOperations.html ) and i want have only one connection pool in my application.
Thanks,
Kind regards,
Marcin Zduniak / http://J2ME.plRefer
http://www.oracle.com/technology/products/jdev/howtos/10g/usingdatasources/using_datasources.html -
To obtain BufferedImage from Scene 3D
Hi all!!! I want to obtain snapshots from Scene 3D to do a video with JMF (Java Media Framework). How I do it??
Regards!// read the buffer to byteBuffer
GL11.glReadBuffer(GL11.GL_FRONT);
ByteBuffer pixels = ByteBuffer.allocateDirect(400*400*4);
GL11.glReadPixels(0, 0, 400, 400, GL11.GL_RGB, GL11.GL_UNSIGNED_BYTE, pixels);
ColorModel glColorModel = new ComponentColorModel(ColorSpace.getInstance(ColorSpace.CS_sRGB),
new int[] {8,8,8,0},
false,
false,
ComponentColorModel.OPAQUE,
DataBuffer.TYPE_BYTE);
int[] bitMasks = new int[] {8,8,8,0};
int[] band = new int[3];
// again, what is this?
SinglePixelPackedSampleModel sampleModel = new SinglePixelPackedSampleModel(DataBuffer.TYPE_BYTE, 400, 400,bitMasks);
// make array from byteBuffer to make a DataBufferByte from array...
byte [] byteA=new byte[400*400*3];
System.out.println(byteA.length);
pixels.get(byteA);
DataBuffer db = new DataBufferByte(byteA, 400*400*3, 0);
//make my raster
WritableRaster raster = Raster.createInterleavedRaster(db, 400, 400, 400*3, 3, band, null);
// make my image
BufferedImage image = new BufferedImage(glColorModel, raster, false, null);//new java.util.Hashtable());the above produces an image! yey! it is however grayscale, can anybody help?
Edited by: IJustWantToSayHelloWorld on Aug 5, 2009 4:12 AM -
Is there any way to obtain time from an NTP server in LabView?
I would like to be able to obtain time from and NTP server and then use that to set the time on a PCI IRIG-B card. I haven't been able to find any LabView documentation indicating if this is possible or not through LabView.
Check: Code library -> Browse by Company -> NASA -> Timesync.
It's a NIST time syncronizer. I never checked it myself, but NIST has NTP servers so this may help you on your way. -
Obtain drivers from MS-Server and updates from WSUS
Hi,
is there a possibility to obtain drivers from the MS Server and the "other" updates from the WSUS-Server?
We have workstations with Win7 and XP and pluged in devices (USB) should obtain the drivers (if available) automatically from MS-Server.
Obtaining drivers through WSUS is not an option.
The Group Policy "Computer Configuration\...\Windows Update" is set to obtain updates from "intranet Microsoft update service location".
Should there be no possibility to distinguish between driver and update obtaining locations,
then is it possible to set WSUS as primary obtaining location and as secondary the MS-Serve?
Greets,
EmmanuelLike I mentioned before I tried to use this:
http://technet.microsoft.com/en-us/library/cc753091.aspx
1. Try:
Step1:
I uninstalled the device and deleted the driver of my testing device. (local)
Step2:
I have created a new GP on Server 2003R2x86 (AD/DC) and linked it in the OU where my test-PC is located.
.../ComputerConfiguration/Administrative Templates/System/InternetCommunicationManagement/Internet Communication Settings/TurnOffWindowsUpdateDeviceDriverSearching-->disabled
Step3:
I restarted the test PC with a logonscript: "gpupdate /force"
Result:
It didn't work.
2.Try:
Same procedure, but instead of creating the policy on the '03 Server, I created the policy with RSAT for W7.
Result:
It didn't work.
Now I have a new question:
Isn't the above mentioned policy for this?:
http://windows.microsoft.com/en-us/windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware
I ask, because this is exactly the setting that has to be changed so that everything works the way I want.
(at least for the Win7 PCs. I don't care much about the XP-PCs because they will be replaced in the near future)
Well one option is to change this setting manually on every PC, but this would be a huge PITA.
Can this be done in a policy or with a script (registry?)? -
For some reason my QuickTime player has stopped playing all my .avi movies, I can't seem to upgrade and it doesn't offer any solutions except that it may need additional software but not what or where to obtain it from? Help most of my movie are in .avi!!
Google 'Perian' and 'Flip4Mac' — these are the extensions that will make QT play other file formats.
However, a simpler solution is just to abandon QT in favour of the free, open-source player VLC, which plays just about everything natively without further downloads.
Download the free VLC Player from here:
http://www.videolan.org
Plays just about everything, including avi & mpg, without add ons. -
Sample java code to obtain data from ALUI directory
Hi
I need to go to the ALUI LDAP ( directory ) services to get user profile information.
The documentation did not help me to figure out the way to obtain data from it.
so , it would be a great help if some one could share the sample java code api to obtain data from ALUI directory.i'm guessing you are asking to get the groups for a particular user. someone in the other thread posted the actual SQL, that may be easier. ( you are on 10gR3 right, because ALUI directory didn't exist before 6.5)
I dont have a sample done yet, but the internet is filled with samples of java and ldap...
http://www.coderanch.com/t/133108/Security/LDAP-sample-program -
We are getting an error on the authentication piece when trying to submit a file to the OfficialFile.asmx web service to submit a document to the Drop-Off Library. Here is the code snippet -
public string FileUpload(HttpPostedFile FileInput, RecordsRepositoryProperty[] properties)
string strFileUrl = string.Empty;
RecordsRepositorySoapClient repository = new RecordsRepositorySoapClient();
BinaryReader b = new BinaryReader(FileInput.InputStream);
byte[] binData = b.ReadBytes(FileInput.ContentLength);
repository.ClientCredentials.Windows.ClientCredential = new System.Net.NetworkCredential(iUserID, iUserPassword, iUserDomain);
repository.ClientCredentials.Windows.AllowedImpersonationLevel = System.Security.Principal.TokenImpersonationLevel.Impersonation;
repository.SubmitFile(binData, properties, null, FileInput.FileName, HttpContext.Current.User.Identity.Name);
strFileUrl = repository.GetFinalRoutingDestinationFolderUrl(properties, null, FileInput.FileName).Url;
return strFileUrl;
Although we are setting the network credential in the client call we still get the error
- The HTTP request is unauthorized with client authentication scheme 'Anonymous'. The authentication header received from the server was 'Negotiate,NTLM'.
Ideas?
Thanks in advance.Hi,
Based on the error message, the issue is related to the authentication type.
I suggest you can specify the credential type like the below:
CredentialCache credentialCache = new CredentialCache();
NetworkCredential credentials = new NetworkCredential(UserName, PassWord, sDomain);
credentialCache.Add(new Uri(recordCenterUrl), "NTLM", credentials);
Here is a detailed code demo for your reference:
http://blogs.msdn.com/b/mcsnoiwb/archive/2011/06/06/sending-files-to-a-record-center-using-the-sp2010-webservice-officialfile-asmx.aspx
Best Regards
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Jerry Guo
TechNet Community Support -
How do i obtain permission from Apple to use Classic Visualizer in a private Youtube video? SoundSpectrum says Apple has jurisdiction over Classic Visualizer.
SoundSpectrum says Apple has jurisdiction over this product. This is strictly for non-commercial use.I did end up using an apple thunderbolt to DVI.
Next a DVI to HDMI.
Component Video + Digital Coaxial and Digital Optical Audio to HDMI® Converter
http:/http://www.monoprice.com/Product?c_id=101&cp_id=10114&cs_id=1011406&p_id=5 971&seq=1&format=2
After that I used an HDMI to component.
Kanex Pro HDMI to Component Converter with Audio for PS4, Xbox One, Full HD 1080p (HDRGBRL)
https://www.google.com/shopping/product/13562420314864684603?q=Kanex+Pro+HDMI+to +Component+Converter+with+Audio+for+PS4,+Xbox+One,+Full+HD+1080p+(HDRGBRL)&espv = 2&biw=1461&bih=724&bav=on.2,or.r_cp.&bvm=bv.89947451,d.cGU&ion=1&tch=1&ech=1&ps i =lcMhVcDPEpC4ogTBl4LABg.1428276117592.5&prds=paur:ClkAsKraX2IpeY7X336NKCAZO5gXZ C fr9CYkefRrD0Ad_Xy607mRERaZVy-e31nis3rQppz_OgnNmy5ApOtsfxdiNa9ObBt6XIj0T_QHJnHgQ S RKEgr403gF3BIZAFPVH73q3thgw88E5DYtSJ2ucji5lQO4ow&sa=X&ei=nMMhVfSkCIftoATK24GYCA & ved=0COEDEPMCMAA
On my iMac:
I had to go into my device settings > Display
then I set the "Optimize for:" to "CAT-6066"
after that I selected the "Scaled" option right underneath
then i selected 1080i because the Kanex Pro is designed to convert 1080i into component
I was then able to get my NewTek Tricaster 40 to recognize that component signal from the Kanex Pro and add it to my production as 1080i or as 1080p/30. The frame rate looks great and the video quality is very smooth and in real time. -
How do i obtain information from my hard drive
how do i obtain information from my hard drive?
Your question is not at all clear - perhaps you could rephrase it more succinctly?
-Rob -
Problems with custom authentication when migrating from 3.2 to 4.1.1
Hi,
we’re about to upgrade our APEX instances to 4.1.1 and to migrate our applications. I encountered some problems with our custom authentication schema.
1. Recognize already authenticated sessions: in 3.2 the sentry function could return false as long as the user was not authenticated. Public pages could still be displayed (including the login page). The result of the function apex_custom_auth.is_session_valid returned false until once the sentry function returned true. How can I recognize non authenticated sessions in 4.1.1? I looked for the test the Condition “User is the public user (user has not authenticated)” computes on a page but didn’t found the right one. It’s not what docu states here (comparison with the public user): http://docs.oracle.com/cd/E23903_01/doc/doc.41/e21674/condition001.htm#HTMDB25943. I replaced the test with p_authentication.username = ‘nobody’. It works. But that doesn’t seem to me to be the right way …
2. Post_logout lacks session context: the Post Logout Procedure does not receive a session_id and username. Neither the V(‘APP_SESSION’) nor p_authentication.session_id are set. This applies to both plugin authentication schemes and non-plugin custom authentication schemes. Is there another way to obtain the logged-out sessions infos or is this a bug?
See apex.oracle.com for a demo, workspace WS_MW, gast/gast. Can someone please guide me the way?
MichaelHello again,
there are no replies until now .... I reviewed some posts regarding custom authentication again and did not find any solution for the issues. Found some that worked with APEX 3.2.1 but not with 4.1.1. I can only work around
1.) in an insecure way, because the non documented (?) user "nobody" can change and all new sessions will be considered authenticated
2.) in a way, that ends up in implementing the logout from the non apex environment outside the authentication schema or authentication plugin.
May be I should contact support for at least the second issue because this doesn't work as documented or am I doing something wrong?
Michael -
Aargh! Five(!) "authentication required" prompts from Firefox!
I'm starting to use JavaScript in an application which is fount at the internal-only address (say...):
http://tlcapps/bah-humbug/ihatechristmas.cfm
The opening page contains four JavaScript links ... and guess what Firefox is doing! Prompting four or five times in a row for my credentials! (Then, the page opens up just fine.)
I have already tried to use this admonition, obtained from somewhere and variously confirmed by others:
To enable windows authentication on your domain.
1. Open Firefox
2. Navigate to the url about:config
3. Locate the following preference names and put as the value the comma separated values of the address roots.
network.automatic-ntlm-auth.trusted-uris
network.negotiate-auth.delegation-uris
network.negotiate-auth.trusted-uris
Your value should look something like this: localhost,server1,server2,serverX
But without success. (I entered "tlcapps" into these boxes.)
What am I doing wrong? (At my age, I don't have hair-follicles to spare!)Okay, Ian... please re-cap exactly "what worked for you":
Are we in agreement that I should be entering "tlcapps" ?
There appear to be three different configuration-parameters "in play" here ... and although I have not (yet) sought to find documentation for them from the FireFox people, they do appear to have fundamentally different purposes, i.e. "trust" vs. "delegate." Could they conflict in some way?
The multiplicity of prompts clearly is coming from the <script> tags in the body of the HTML, because I observe that the number of 'extra' prompts is directly related to the number of script-tags that occur. Did the case that you speak of do the same?
There is a "junk-buster" proxy server living on the local box. (It's the only way I can survive using the Internet these days...) Could this have any relevance?
At this point, I feel like "FireFox thinks it has 'a good reason for asking,' but I don't yet quite know what that 'reason' is." -
How do I obtain data from a web site???
I am trying to use information from a sports stats page to automate scoring on a fantasy football site I am developing. After a game the weeks games have completed, I want to be able to extract the data, passing yards, passing TD's, etc. I can pull in a web site, and get to the point where the QB stats start. My question is there a way to strip all the html tags and just be left with the players name and numbers(stats)? I skip down 366 lines to get to the example below. Was thinking maybe, to tokenize using > as the delimiiter, then tokenizing again to strip away the rest of the tag using < as the delimiter. Any suggestions are much appreciated, thanks.
CODE
import java.net.*;
import java.io.*;
public class WebRipper
public static void main(String[] argv)
int count = 0;
try {
// Create a URL for the desired page
URL url = new URL("http://www.fftoday.com/stats/playerstats.php?Season=2006&GameWeek=1&PosID=10&Le agueID=1");
// Read all the text returned by the server
BufferedReader in = new BufferedReader(new InputStreamReader(url.openStream()));
String str;
while ((str = in.readLine()) != null)
if(count > 366)
System.out.println(str);
}// end if
count ++;
}// end while
in.close();
}// end try
catch (MalformedURLException e) {}
catch (IOException e) {}
}// end main
}// end WebRipper
OUTPUT(this is just a example of the first few lines of output)
<TD CLASS="sort1" ALIGN="LEFT" BGCOLOR="#ffffff"> 1. Donovan McNabb</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">PHI</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">1</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">1</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">24</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">35</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">314</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">3</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">1</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">4</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">7</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">0</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#e0e0e0">28.4</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">28.4</TD>
</TR>Here is the first string I would want to obtain, can you explain how I would get the player name, then all of his stats. Remember there is ~366 lines of text before you get to this point. Also what or where should I dump the info to?
Example from the info below I want Donovan McNabb, then all of his stats, excluding all the tags.
<TD CLASS="sort1" ALIGN="LEFT" BGCOLOR="#ffffff"> 1. Donovan McNabb</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">PHI</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">1</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">1</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">24</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">35</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">314</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">3</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">1</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">4</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">7</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">0</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#e0e0e0">28.4</TD>
<TD CLASS="sort1" ALIGN="center" BGCOLOR="#ffffff">28.4</TD>
</TR>
Pattern p = Pattern.compile("(?<=\\>)[^<]+");
Matcher matcher = p.matcher(yourwebinfo);
while(matcher.find())
yourinfow/ohtmlcode = matcher.group();
Thanks.
Maybe you are looking for
-
Create Drop Folder With Drop Only
Mini Server, Mid 2011, 2 GHz, Intel Core i7, OSX 10.9.4 I have my server with a static ip and would like to create a password protected folder with drop only features. I tried Pure FTP software for this, what info do I need to give my client to acces
-
Loading a CSV file into a table as in dataworkshop
Data Workshop has a feature to load a CSV file and create a table based on it, similarly i want to create it in my application. i have gone through the forum http://forums.oracle.com/forums/thread.jspa?threadID=334988&start=60&tstart=0 but could not
-
would you get a better picture on apple tv is you used airplay on an ipad mini with retina display as opposed to a standard ipad mini?
-
Hi All, Does anybody how to export adf table records to excel without using DCIteratorBinding. i want to implement in Backing Bean is it possible?
-
Uh oh ! Can I import my addresses ?
I have read several topics below, but they haven't solved my problem. Is there no way to import my addresses ? My imac G5 OS 10.3.9 has a logic board issue and is unusable. I was able to back up the HD by firewiring it into another mac, onto an iomeg