Authentication Failed - newbie

I am managing 4 other systems, which all have the same admin user name and password. 2 of the systems I cannot Observe/Control/Curtain. I can chat, message, install etc... Each time I double click on them I get 'Authentication Failed to "X Machine"'. I used to have access to all 4 workstations 2 weeks ago. Why did I loose access to these 2 machines? Nothing has been done to these systems to warrant this sudden loss of access. Any ideas?
Sly
Dual 2GHz Power PC G5 Mac OS X (10.4.8)

The two most likely cases are:
1) Someone disabled the control/observe priveleges in the control panel.
2) Port 5900 is being blocked (probably by the software firewall).

Similar Messages

Authentication Failed!? Can someone help please?

Hi everyone,
I'm in need of some real assistance. I have currently purchased and installed ARD 3.0 on my laptop. My girlfriend has just bought her first Mac computer - a new intel iMac. Wanting to help her remotely, I installed the client installer created by my ARD3 version. When I try to connect, it doesn't let me. It says "Authentication Failed". We even tried taking off the password to make it easier, but still nothing. I can connect by "Connect to Server" through the finder, but I just don't understand why it won't connect me through ARD. I've read a few forums about the intel problem, but I understood that problem is having ARD3 installed on the computer as in, "the master host" and not the client installer. Is that right?
Can someone tell me if I am supposed to install the whole program on the iMac I am trying to connect to or does it just have to be on my computer and everyone else gets the custom "Client Installer" I've created. In her preferences under Sharing, it doesn't show Access Privileges, where as it does on mine as I have it fully installed on mine. I am very confused and feeling like a total newbie. Any assistance would be greatly appreciated. Thank you.

Same issue here. I have 25 nodes (mix of Pmacs 2x/4x) and am trying to get imaging going as we're replacing some of the 2x with 4x, Using NetRestore and a lot of help from local experts, I've got the imaging working, but even tho the new nodes are imaged from an existing one (and then renamed), I cannot connect to them with ARD 3.0 (Authentication Failed to [node]).
The nodes are set up to get IPs based on MAC addresses from a MacOSX Server running DHCP and this part works well - they're getting the right IP #s, but not connecting via ARD. They show up in the ARD panel with the correct IP number and ARD version #, but the DNS name is missing (should be 'Q2L1.local' and is blank.)
What kind of auth is being sought? Is it trying to get kerberos authentication via the Server? That service is on and appears to be working fine, altho I could imagine that since it's running off an imaged disk, there might be some kind of auth invalidation occuring.
However, in checking the Server Open Directory logs, I see:
Jul 20 2006 11:59:31 AUTH2: {0x446d07630c6cdd5e0000000f0000000f, hjm} DHX authentication failed, SASL error -13 (password incorrect).
Jul 20 2006 11:59:31 QUIT: {0x446d07630c6cdd5e0000000f0000000f, hjm} disconnected.
Jul 20 2006 11:59:32 RSAVALIDATE: success.
Jul 20 2006 11:59:32 AUTH2: {0x446d07630c6cdd5e0000000f0000000f, hjm} DHX authentication failed, SASL error -13 (password incorrect).
Jul 20 2006 11:59:32 QUIT: {0x446d07630c6cdd5e0000000f0000000f, hjm} disconnected.
I'm logged into the server as 'hjm' but I don't have an account on the target machine (nor the image source machine which works just fine).
The above errors suggest that it's a DHX key problem, but why should it involve 'hjm' and not the user logged in, or the user trying to log in?
Incidentally, resetting the passwd for the logged in user does not work.
***? (Why The Failure?)
Harry

Cisco ISE authentication failed because client reject certificate

Hi Experts,
I am a newbie in ISE and having problem in my first step in authentication. Please help.
I am trying to deploy a standalone Cisco ISE 1.1.2 with WLC using 802.1x authentication. The user authentication configured to be checked to ISE's internal user database for early deployment. But when the user try to authenticate, they failed with error message in ISE :
Authentication failed : 12321 PEAP failed SSL/TLS handshake because the client rejected the ISE local-certificate
I've generate a certificate for ISE using Windows Server CA and replace ISE's self-signed certificate with the new certificate but authentication still failed with the same error message. Must I generate a certificate for WLC also? Please help me in solving this problem.
Regards,
Ratna

Certificate-Based User Authentication via Supplicant Failing
Symptoms or
Issue
User authentication is failing on the client machine, and the user is receiving a
“RADIUS Access-Reject” form of message.
Conditions (This issue occurs with authentication protocols that require certificate validation.)
Possible Authentications report failure reasons:
• “Authentication failed: 11514 Unexpectedly received empty TLS message;
treating as a rejection by the client”
• “Authentication failed: 12153 EAP-FAST failed SSL/TLS handshake because
the client rejected the Cisco ISE local-certificate”
Click the magnifying glass icon from Authentications to display the following output
in the Authentication Report:
• 12305 Prepared EAP-Request with another PEAP challenge
• 11006 Returned RADIUS Access-Challenge
• 11001 Received RADIUS Access-Request
• 11018 RADIUS is reusing an existing session
• 12304 Extracted EAP-Response containing PEAP challenge-response
• 11514 Unexpectedly received empty TLS message; treating as a rejection by the
client
• 12512 Treat the unexpected TLS acknowledge message as a rejection from the
client
• 11504 Prepared EAP-Failure
• 11003 Returned RADIUS Access-Reject
• 11006 Returned RADIUS Access-Challenge
• 11001 Received RADIUS Access-Request
• 11018 RADIUS is re-using an existing session
• 12104 Extracted EAP-Response containing EAP-FAST challenge-response
• 12815 Extracted TLS Alert message
• 12153 EAP-FAST failed SSL/TLS handshake because the client rejected the
Cisco ISE local-certificate
• 11504 Prepared EAP-Failure
• 11003 Returned RADIUS Access-Reject
Note This is an indication that the client does not have or does not trust the Cisco
ISE certificates.
Possible Causes The supplicant or client machine is not accepting the certificate from Cisco ISE.
The client machine is configured to validate the server certificate, but is not
configured to trust the Cisco ISE certificate.
Resolution The client machine must accept the Cisco ISE certificate to enable authentication.

EAP-TLS or PEAP authentication failed during SSL handshake

Hi Pros,
I am a newbie in the ACS 4.2 and EAP-TLS implementation, with that being said. I face an issue during a EAP-TLS implementation. My search shows that this kind of error message is already certificate issue;However, I have deleted and recreated the certificate in both ACS and the client with the same result. I have deleted and re-install the certchain as well.
When I check my log in the failed attemps, there is what I found:
Date
Time
Message-Type
User-Name
Group-Name
Caller-ID
Network Access Profile Name
Authen-Failure-Code
Author-Failure-Code
Author-Data
NAS-Port
NAS-IP-Address
Filter Information
PEAP/EAP-FAST-Clear-Name
EAP Type
EAP Type Name
Reason
Access Device
Network Device Group
06/23/2010
17:39:51
Authen failed
000e.9b6e.e834
Default Group
000e.9b6e.e834
(Default)
EAP-TLS or PEAP authentication failed during SSL handshake
1101
10.111.22.24
25
MS-PEAP
wbr-1121-zozo-test
Office Networ
06/23/2010
17:39:50
Authen failed
[email protected]
Default Group
000e.9b6e.e834
(Default)
EAP-TLS or PEAP authentication failed during SSL handshake
1098
10.111.22.24
25
MS-PEAP
wbr-1121-zozo-test
Office Network
[email protected] = my windows active directory name
1. Why under EAP-TYPE it shows MS-PEAP not EAP-TLS? I did configure EAP-TLS....
2. Why sometimes it just shows the MAC of the client for username?
3. Why it puts me in DEFAULT-GROUP even though i belongs to a group well definy in the acs?
2. Secondly, When I check in pass authentications... there is what i saw
Date
Time
Message-Type
User-Name
Group-Name
Caller-ID
NAS-Port
NAS-IP-Address
Network Access Profile Name
Shared RAC
Downloadable ACL
System-Posture-Token
Application-Posture-Token
Reason
EAP Type
EAP Type Name
PEAP/EAP-FAST-Clear-Name
Access Device
Network Device Group
06/23/2010
17:30:49
Authen OK
groszozo
NOC Tier 2
10.11.10.105
1
10.111.22.24
(Default)
wbr-1121-zozo-test
Office Network
06/23/2010
17:29:27
Authen OK
groszozo
NOC Tier 2
10.11.10.105
1
10.111.22.24
(Default)
wbr-1121-zozo-test
Office Network
In the output below, it says that the user is authenticate and it puts the user in the right group with the right username, but the user never really authenticate. Maybe for the first few seconds when I initiate the connection.
Before I forget, the suppliant is using WIN XP and 802.1x is enable. I even uncheck not verify the server and the ACS under External User Databases, I did check ENABLE EAP-TLS machine authentication.
Thanks in advance for your help,
Crazy---

Any ideas on this guys?? In my end, i've been reading some docs... Things started to make sens to me, but I still cannot authenticate, still the same errors. One more thing that catch my attention now is the time it takes to open a telnet session to cisco device which has the ACS for auth server.
My AD(Active Direct) and the ACS server are local same subnet(server subnet). Ping to the ACS from my desktop which is in different subnet is only take 1ms. To confirm that the issue is the ACS server, I decided to use another server in remote location, the telnet connection is way faster than the local ACS.
Let's brain storm together to figure out this guys.
Thanks in advance,
----Paul

NoMachine(freenx) Authentication failed for user (MYUSERNAME)

Hi all,
I have quite a few experience with freenx on other linux distributions, but this is my first time setting up freenx on archlinux. After following the instructions in the wiki, authentication keeps failing no matter what I do.
Stuff I've done from the wiki:
1. install freenx
2. add RSAAuthentication yes AllowUsers someuser nx to sshd_config
3. add md5sum to node.conf
4. pacman -S xdialog xterm
5. run "/usr/bin/nxsetup --install --setup-nomachine-key"
6. modify /etc/nxserver/node.conf so that "USER_X_STARTUP_SCRIPT=.xinitrc"
7. pick the right configurations when connecting to my server
I have "exec startxfce4" in .xinitrc.
It always goes up to "Waiting for authentication" and then "Authentication failed for user (MYUSERNAME)" pops up. I think it should not be a XFCE issue since authentication itself didn't even pass. I assume if it is a X window problem, what I would get is something like a blank screen.
I'm using public key, so I didn't really copy anything from the server to my client.
I couldn't think of a second reason why this wouldn't work. Is there any thing obvious that I missed? (If so, please move this thread to the newbie corner. lol)
Any thoughts would be highly appreciated.
Thanks
Aweather

Hi,
I did update the password in the properties file but still I get the error
BUILD FAILED
C:\product\10.1.3.1\OracleAS_1\bpel\samples\utils\CreditRatingService\build.xml:
79: Authentication failed for user "oc4jadmin" on host
I am able to deploy from JDEV. and could configure as per documentation
Thanks in advance,
Anand
I had to update the <OH>/bpel/utilities/ant-orabpel.properties file for the password and now I can deploy successfully...information was there in the readme file...
Anand
Message was edited by:
AnandP

SAP Business One Integration Services Authentication Failed

Dear ,
ALL SAP forum members,
Iam Using SAP Business One 8.81 PL 06, Micorsoft SQL 2008 R2
In SLD B1DI and JDBC, the connections were tested successfully.
Whenever I log into SBO, I am getting "SAP Business One Integration Services Authentication Failed" error message. I did extensive research on all possible SBO documents dating 1 year back especially in B1ic Troubleshooting Document (New and Old) and searched the length of the SBO forums, but I could not a solution.
I uninstalled and reinstalled the B1f package many a time. The integration services we re also restarted many times and the connections were all tested successfully. Firewall, AntiVirus also checked.
In the B1f, in the Monitoring Window, the login is "Ok" but the AuthCheck is "Failed". I checked Authent.Monitor->Authentic Info and I found the following message under Action message "Wrong Usrname and Password".
I debugged and i found again "/com.sap.b1i.vplatform.scenarios.authen/sap.Xcelsius/Authenticate_Check.bfd
But could not understand much of it.
But i could go no further. The experts are requested to suggest their solutions, If any, to me as Iam stuck in this phase for the last 3 week
I hope some experts will guide me over this issue
Thanks and regards
Ashish Gupte

Hi Konstantin Ryahovsky
Thanks for your reply. My problem is solved.
And frankly speaking i dont know how it was solved. I have not uninstall, install ,not even i had restarted the server also.
only change i did in SLD >> Maintainance >>> cfg Runtime >>>> Put server IP address instead of server Name and restarted the services.
Thanks & regards
Ashish Gupte

Toshiba EXCITE Pro - WIFI connection. Authentication failed after update

Hello.
Just received this Tablet.
Everything seemed ok while updating to the latest version (did that first to solve the heat problems).
After the last update *i lost my WIfi connection. Authentication failed* (didnt change something - was connecting - updating ok 1 minute before the last update).
After that i started testing ,Wps connection , No security Wifi etc etc.
*Finally at a random time (and with the initial settings) i got connected*. After i shut down the tablet the same problem occured.
After doing the same things again i finally got connected and this time it seems to be ok, even after i shut down the tablet.
However this is frustrating.
Maybe you have to sort this out?
I have seen and other people returning this tablet after having this problem.
It is not a hardware problem since its working ok before the update.
Of course tried factory reset twice.
Hope i dont have this problem again, *but i am informing in hope that you fix this in a future update.*

Toshiba sent me the fix for this. Figured I would use Facebook and they sorted a solution straight away.
It requires a complete reset. Not the soft reset from within Android.
I'll post it here as they will check through moderation I guess.
Thanks for sending a private message Ben. For us to get this resolved for you we would advise to perform a reset from the Android system recovery menu, to do the reset please follow these steps:
The reset process will delete any data, settings, and applications on your tablet. You must have a backup of any data you wish to keep before proceeding.
1. Make sure the tablet is off and not in standby.
2. Hold down the Volume Up and Power buttons simultaneously until the two Android icons appear.
3. Use the volume buttons to select the white box on the right.
4. Once selected, press the power button.
5. Use the volume buttons to select wipe cache partition and then press the power button.
6. Select Yes and press the power button.
7. Use the volume buttons to select wipe data/factory reset and then press the power button.
8. Select Yes and press the power button.
9. The tablet will now reset.
If you have any issues after the reset please get back to us as soon as possible!
Its been working well ever since. I guess the cache clean part might be the main one. You'll have to select the reboot yourself as I did at the end.
Might be best to use Facebook i'll see if I can find my post as the response was quick and efficient unlike their responses in here. I.e nowt from them so far.
They needed my name and serial numbers probably to log problems etc.
Message was edited by: bensimmo

I'm trying to connect through the FTP client Filezilla. When I try to login with the wizard, it gives me a "503 Failure of Data Connection" reply; when I attempt to login myself, it gives me a "530 Login Authentication Failed." HELP!!!

My current softward is: Mac OS X Lion 10.7.5 (11G63)
When I attempt to use the Filezilla connection wizard I get the following message:
Connecting to probe.filezilla-project.org
Response: 220 FZ router and firewall tester ready
USER FileZilla
Response: 331 Give any password.
PASS 3.7.1.1
Response: 230 logged on.
Checking for correct external IP address
Retrieving external IP address from http://ip.filezilla-project.org/ip.php
Checking for correct external IP address
IP 27.0.19.56 ch-a-bj-fg
Response: 200 OK
PREP 52470
Response: 200 Using port 52470, data token 1871898076
PORT 27,0,19,56,204,246
Response: 200 PORT command successful
LIST
Response: 150 opening data connection
Response: 503 Failure of data connection.
Server sent unexpected reply.
Connection closed
When I attempt to login Host/Username/Password myself I get the following message:
Status:          Resolving address of amyhoney.com
Status:          Connecting to 184.168.54.1:21...
Status:          Connection established, waiting for welcome message...
Response:          220---------- Welcome to Pure-FTPd [privsep] [TLS] ----------
Response:          220-You are user number 12 of 500 allowed.
Response:          220-Local time is now 04:05. Server port: 21.
Response:          220-This is a private system - No anonymous login
Response:          220 You will be disconnected after 3 minutes of inactivity.
Command:          USER 5475****
Response:          331 User 5475**** OK. Password required
Command:          PASS ********************
Response:          530 Login authentication failed
Error:          Critical error
Error:          Could not connect to server
Now before anyone points out the obvious: my username and password are correct. I've already gone through changing them so I know they are.
Additionally, I've pretty much tried EVERYTHING I've read online, from messing with "terminal" (and subsequently the FTP and STFP options) to changing the sharing options and turning on file sharing/remote management as well as just turning off my Firewall completely.
Now I've used Filezilla before when I first published my site and everything worked fine. My site is published through Wordpress so most of my editing was done through simply logging into my "wp-login." I recently changed the theme and in order to change the header image in that theme I have to do it through my "wp-content" folder, which means I need to use Filezilla. I feel like a complete moron right now considering I've had my site for about a year and can't even doing something this simple.
I've read that the newer version of Lion/Mountain Lion don't support automatice FTP anymore, which (as I mentioned prior) I attempted to fix through Terminal. However, nothing I do seem to do works.
Can someone walk me through fixing this? And I do mean 'walk me through'. I'm not a tech-savvy nerd who knows all the lingo, I just know the basics so sorry if my ignorance offends you.
HELP!!

First be sure login and password are OK. Sometimes the address starts wit "http://..." and sometime starts with "ftp://...". Try both normal FTP access and Scure FTP access (SFTP). At the end, contact the site's provider.

OBIA 7.9.5 EBS Integration Not Logged On nQSError 43001 Authentication Fail

Hi,
I'm attempting to get Oracle Business Intelligence Applications 7.9.5 / OBIEE 10.1.3.3.2 integrated into the eBusiness Suite 11.5.10.2 per Metalink Note 552735.1. At the moment not an action link, just menu option to SA Administrator.
I've run into and worked around a number of problems with the Initialization block variables setup in OracleBIAnalyticsApps.rpd and now no longer get errors in the NQServer.log after disabling Initialization Blocks for Siebel/Peoplesoft and disabling 2 EBS specific Init blocks that were erroring; 'Inventory Organizations' and 'Ledgers' I'll fix those later.
However, now I get an error in the sawlog0.log file as follows:
File: project/webodbcaccess/odbcconnectionimpl.cpp Line: 371
Properties: ConnId-6,6;ThreadID-1145072560
Location:
saw.odbc.connection.open
saw.connectionPool.getConnection
saw.threadPool
saw.threads
Odbc driver returned an error (SQLDriverConnectW).
State: 08004. Code: 10018. NQODBC [SQL_STATE: 08004|http://forums.oracle.com/forums/] [nQSError: 10018|http://forums.oracle.com/forums/] Access for the requested connection is refused.
[nQSError: 43001|http://forums.oracle.com/forums/] Authentication failed for in repository Star: invalid user/password. (08004)
Type: Error
Severity: 42
Time: Wed Dec 3 07:13:16 2008
File: project/webconnect/connection.cpp Line: 276
Properties: ThreadID-1145072560
Location:
saw.connectionPool.getConnection
saw.threadPool
saw.threads
Authentication Failure.
Odbc driver returned an error (SQLDriverConnectW).
Can anyone point me in the right direction here?
Thanks,
Gareth

The strange thing is both Gareth and I have configured OBIA/OBIEE on a Linux server and local authentication works fine. Once we enable external EBS authentication, we get the error listed above.
Does anyone who has done the OBIA EBS integration with OBIEE running on Linux have an example of the odbc.ini file. It appears that even though we have reconfigured OracleBIAnalyticsApps.rpd to use OCI everywhere, that there is still some hard coded ODBC references for external authentication.
We are configuring instanceconfig.xml as directed:
Integrating Oracle Business Intelligence Applications with Oracle E-Business Suite
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=552735.1
Configuring InstanceConfig.xml for External Authentication
1. Modify the instanceconfig.xml file for the Oracle BI Presentation Services as shown below:
<?xml version="1.0"?>
<WebConfig>
<ServerInstance>
<CatalogPath>c:\temp\default</CatalogPath>
<DSN>AnalyticsWeb</DSN>
<Auth>
<ExternalLogon enabled="true">
<ParamList>
<Param name="NQ_SESSION.ICX_SESSION_COOKIE"
source="cookie"
nameInSource="EBSAppsDatabaseSID"/>
<Param name="NQ_SESSION.ACF"
source="url"
nameInSource="ACF"/>
</ParamList>
</ExternalLogon>
</Auth>

</ServerInstance>
</WebConfig>
2. The nameInSource for the cookie should be the same as the Oracle E-Business Suite application database SID name. To verify the name of the cookie, using Firefox, check the name of the cookie created under the us.oracle.com domain (or the domain where your Oracle E-Business Suite Application server is running). Please note that the cookie name is case sensitive.

BO XI 3.1 : Active Directory Authentication failed to get the Active Directory groups

Dear all
        In our environment, there are 2 domain (domain A and B); it works well all the time. Today, all the user belong to domain A are not logi n; for user in domain B, all of them can log in but BO server response is very slowly. and there is error message popup when opening Webi report for domain B user. Below are the error message:
       " Active Directory Authentication failed to get the Active Directory groups for the account with ID:XXXX; pls make sure this account is valid and belongs to an accessible domain"
      Anyone has encountered similar issue?
   BO version: BO XI 3.1 SP5
   Authenticate: Windows AD
Thanks and Regards

Please get in touch with your AD team and verify if there are any changes applied to the domain controller and there are no network issues.
Also since this is a multi domain, make sure you have 2 way transitive forest trust as mentioned in SAP Note : 1323391 and FQDN for Directory servers are maintained in registry as per 1199995
http://service.sap.com/sap/support/notes/1323391
http://service.sap.com/sap/support/notes/1199995
-Ambarish-

User Authentication Failed error when trying to display a JSP portlet

The steps carried out are as follows :
1. Created a JSP file named "c.jsp" and deployed it under 902_MidTier_Home\j2ee\home\default-web-app\examples\jsp
2. Created a table named USER_TABLE under Scott schema to store the usernames and passwords to validate this JSP application.
3. Registered this JSP as an external application with the following values :
Application Name           : RAGHU
Login URL          : http://hostname:port/j2ee/examples/jsp/c.jsp
User Name/ID Field Name     : username
Password Field Name     : password
Type of Authentication Used : POST
3. Clicked on the External Application and entered the username as USER1 and password as USER1 ( These values are available
under USER_TABLE for comparison ). Then it shows the message "Hi User1 .. Welcome message"
4. Now created a directory named JSPSAMPLE under "WEB-INF\Providers" and put the provider.xml file under this.
Created a raghu.properties file and placed it under "WEB-INF\deployment".
5. Now tested the testpage using the URL " http://hostname:port/jpdk/providers/raghu " and it works fine.
6. Registered this as a provider in Portal and added this portlet onto a page. Assigned this page to a newly created user.
It gives the message " Authentication Failed - Update Login Information " which is expected. I click on the link and
it takes me to the external application username password. I enter the credentials but this time it comes back again
to the page with the same message " Authentication Failed - Update Login Information ".
7. Basically the values are not passed to the Username and Password in jsp page which is why the problem occurs.
The JSP Code used is as follows :
<%@ page import="java.sql.*" %>
<HTML>
<HEAD><TITLE>DB Connectivity test</TITLE></HEAD>
<BODY BGCOLOR="#FFFFFF">
<CENTER>
<B>user_table</B>
<BR><BR>
<%
String username = request.getParameter("username");
String password = request.getParameter("password");
Connection conn = null;
try
Class.forName("oracle.jdbc.driver.OracleDriver");
conn = DriverManager.getConnection("jdbc:oracle:thin:@hostname:1521:iasdb","scott","tiger");
Statement stmt = conn.createStatement();
String query = "SELECT * FROM user_table where userid= '"+ username +"' and passwd = '" + password + "' " ;
ResultSet rs = stmt.executeQuery(query);
while(rs.next())
out.println("<TR>");
out.println(" <TD> hi " + rs.getString("userid") + ", welcome</TD>");
out.println("</TR>");
out.println("</TABLE>");
catch(SQLException e)
out.println("SQLException: " + e.getMessage() + "<BR>");
while((e = e.getNextException()) != null)
out.println(e.getMessage() + "<BR>");
out.println("invalid userid,password");
catch(ClassNotFoundException e)
out.println("ClassNotFoundException: " + e.getMessage() + "<BR>");
finally
//Clean up resources, close the connection.
if(conn != null)
try
conn.close();
catch (Exception ignored) {}
%>
</CENTER>
</BODY>
</HTML>
The Provider.xml file used is as follows :
<?xml version="1.0" encoding="UTF-8"?>
<?providerDefinition version="3.1"?>
<provider class="oracle.portal.provider.v2.http.URLProviderDefinition">
     <providerInstanceClass>oracle.portal.provider.v2.http.URLProviderInstance</providerInstanceClass>
     <session>true</session>
     <authentication class="oracle.portal.provider.v2.security.Authentication">
          <authType>ExternalApp</authType>
          <userFieldName>username</userFieldName>
          <userPwdName>password</userPwdName>
          <errorPageMessages>Raghu,Please sign in,Sign me up!</errorPageMessages>
     </authentication>
     <portlet class="oracle.portal.provider.v2.http.URLPortletDefinition">
          <id>1</id>
          <name>RaghuPortlet</name>
          <title>Raghu Mail Portlet</title>
          <description>This portlet is to test Integration services using mail.yahoo.com</description>
          <timeout>100</timeout>
          <timeoutMessage>Raghu timed out</timeoutMessage>
          <showEdit>false</showEdit>
          <showEditDefault>false</showEditDefault>
          <showPreview>false</showPreview>
          <showDetails>false</showDetails>
          <hasHelp>false</hasHelp>
          <hasAbout>false</hasAbout>
          <acceptContentType>text/html</acceptContentType>
          <registrationPortlet>false</registrationPortlet>
          <accessControl>public</accessControl>
          <renderer class="oracle.portal.provider.v2.render.RenderManager">
               <showPage class="oracle.portal.provider.v2.render.http.URLRenderer">
                    <pageUrl>http://172.17.24.235:8888/c.jsp</pageUrl>
                    <contentType>text/html</contentType>
                    <filter class="oracle.portal.provider.v2.render.HtmlFilter">
                         <useAuthLinks>true</useAuthLinks>
                         <headerTrimTag><table width="100%" cellpadding=0 cellspacing=0 border=0><tr><td bgcolor=#9bbad6></headerTrimTag>
                         <footerTrimTag><table width="100%" cellpadding=2 cellspacing=1><tr><td bgcolor=#9bbad6></footerTrimTag>
                         <convertTarget>true</convertTarget>
                         <redirectUrlFieldName>.done</redirectUrlFieldName>
                    </filter>
               </showPage>
          </renderer>
          <securityManager class="oracle.portal.provider.v2.security.URLSecurityManager">
               <authorizType>registered</authorizType>
          </securityManager>
     </portlet>
</provider>
The Contents of raghu.properties file
serviceClass=oracle.webdb.provider.v2.adapter.soapV1.ProviderAdapter
loaderClass=oracle.portal.provider.v2.http.DefaultProviderLoader
showTestPage=true
definition=providers/raghu/provider.xml
autoReload=true
Any inputs regarding why the values are passed properly in case of External Application but not so when registered as
a portlet in Portal.
Regards
Satish G

As I can see from the information posted, you are trying to
use URL-based portlet's SSO feature, though not in a correct
way.
The SSO feature of URL-based portlets relie on the usage
of Cookies as authentication tokens. For example, in the
present context, http://hostname:port/j2ee/examples/jsp/c.jsp
will write a cookie to the client upon successfull authentication.
Subsequent access to the same JSP or some other JSP in the same
workspace should be checking for the existence of this particular
cookie at the client side and if found should not prompt for
user information again.
If you can fine tune your existing applications as per above
conditions, then everything should work fine. Else you might
want to use page parameters to pass user information.
For more information on page parameters, please visit
http://portalstudio.oracle.com/servlet/page?_pageid=350&_dad=ops&_schema=OPSTUDIO&12678_PDKHOME902_39847486.p_subid=249821&12678_PDKHOME902_39847486.p_sub_siteid=73&12678_PDKHOME902_39847486.p_edit=0#NEW1

Tacacs authentication fails for one user account for only one switch

Hi,
I am having an scenario, where as Tacacs authentication fails for one user account for only one switch.
The same user account works well for other devices.
The AAA configs are same on every devices in the network.
Heres the show tacacs output from the switch where only one user account fails;
              Socket opens:        157
             Socket closes:        156
             Socket aborts:        303
             Socket errors:          1
           Socket Timeouts:          2
   Failed Connect Attempts:          0
        Total Packets Sent:       1703
        Total Packets Recv:       1243
          Expected Replies:          0
What could be the reason ?
No errors on ACS server; same rights had been given to the user account.
Thanks to advise.
Prasey

Hi there,
Does the user get authenticated in the ACS logs?
reports and activity----> failed attempts
ro
reports and activity-----> passed authentications
That will help narrow it down.
Brad

I keep getting a notification that says "Google Talk authentication failed"...does anyone know how to get rid of this? I tried looking for it in the apps but not really sure what google talk is or how to get rid of this message that keeps popping up.

How do i get rid of the message that keeps popping up that says "google talk authentication failed"????

funwidowlady,
Good afternoon! I'm glad I can be here to help with this error. In the device this application is identified only as 'Talk', so that be more familiar to you. First I recommend opening the 'Market' app on your phone, then Menu>My Apps to see if this application requires an update. It will display a list on top of all applications that need to be updated. If nothing exists, tap 'Home' and go into 'Settings>Applications>Manage Applications>Talk, then tap 'Clear Cache' and 'Clear Data' to remove the history of that application and stop the notifications. The app will remain on your phone for future use, if you desire to take advantage of it. Read more about Google Talk here
Thank you!
AdamE_VZW
Follow us on Twitter @VZWSupport

"Ticket authentication failed" error in Principal Propagation scenario

Hi All,
I am working on Principal Propagation, where the scenario is sync RFC-PI-RFC. I have followed all steps mentioned in the below blog. When I execute the scenario (with Principal propagation box checked in the sender agreement) I get dump while executing the RFC from sender system. The dump is:
"Ticket authentication failed"
Scenario works fine if I don't check Principal propagation check box in the sender agreement.
Principal Propagation blog: /people/alexander.bundschuh/blog/2007/01/16/principal-propagation-in-sap-xi
Can anyone suggest what can be the reason for this dump?
Thanks,
Shweta.

Hi All,
Any inputs on this?
Thanks,
Shweta.

Error while saving Report output-Authentication failed

Hi All,
For the client system there is a customization report with output of html format. it can't display all with the error message
unable to open the internet site. http://<site:port>/OA_CGI/FNDWRR.exe?temp_id=<temp_id>*
operation aborted*
if user choose to "save as" , it will back with error message
Authentication failed*
Can anyone here give me some guide?
Best Regards,
Chelsea

Refer Note 184154.1
Regards,
Srini

Authentication Failed - newbie

Similar Messages

Maybe you are looking for