Authorware 7 Transparent mode

Can anyone tell me how to set Transparent mode for all
imported display icons by default. I am currently going through
thousands of imported icons that all need to be switch to
transparent mode.

"geekgasm" <[email protected]> wrote in
message
news:evgr7d$9ei$[email protected]..
> Can anyone tell me how to set Transparent mode for all
imported display
> icons
> by default. I am currently going through thousands of
imported icons that
> all
> need to be switch to transparent mode.
Transparent mode does not belong to the icon, but to the
objects in it.
However, if you select the icons you want to change after all
the graphics
are imported and go to Edit>Change properties, you can
accomplish what you
want.

Similar Messages

The difference between VTP server and transparent mode on Catalyst Switch.

Hello
I have a question about the difference between VTP server mode and VTP transparent mode on general catalyst switch.
Basically VTP server mode can create and modify VLAN configuration but actually there is not any VLAN configuration through running-config, is it true? When I checked it on Cat3550, certainly there is not VLAN configuration on VTP server mode. But VTP transparent can create VLAN and configuration but does not synchronize with other switch VLAN status. I appreciate any related information and reason of the VTP server mode specification, thank you very much.
[VTP Transparent mode]
3550#sh vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 1005
Number of existing VLANs : 27
VTP Operating Mode : Transparent
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
*omit
3550#
3550#sh run
Building configuration...
*omit
vlan 99
name TEST-VLAN
[VTP Server mode]
3550#sh vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 1005
Number of existing VLANs : 27
VTP Operating Mode : Server
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
*omit
3550#
3550#sh run
Building configuration...
*no VLAN like above configuration on VTP transparent mode.
Best Regards,
Masanobu Hiyoshi

Hi mhiyoshi,
3550#sh vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 1005
Number of existing VLANs : 27
VTP Operating Mode : Transparent
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
*omit
3550#
3550#sh run
Building configuration...
*omit
vlan 99
name TEST-VLAN
The above out put indicates that Vlan is created and then mode changed to transparent. i.e why revision no is 0.
3550#sh vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 1005
Number of existing VLANs : 27
VTP Operating Mode : Server
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
*omit
3550#
3550#sh run
Building configuration...
*no VLAN like above configuration on VTP transparent mode.
This indicates that vlan never created in server mode nor learnt from another switch as revision no is 0

Cisco ASA 5512 Transparent mode

Hi all - hope this is the right place to ask this question-
I'm having trouble understanding how to configure an ASA 5512X in what should be a really easy way -
I simply want the ASA to be a transparent Layer 2 "bump" in a routed link between two networks, and then I'll use the Management interface to actually see the firewall ASDM,Syslog, configure, etc.
I have the interfaces set up thusly:
interface GigabitEthernet0/0
nameif UnTrustedNetwork
security-level 0
interface GigabitEthernet0/1
nameif TrustedNetwork
security-level 100
interface Management0/0
nameif ManagementAccess
security-level 100
ip address 192.168.X.Y 255.255.255.0
management-only
I cannot figure out how to install a default route so that interface Management0/0 with it's IP of 192.168.X.Y can be reached from
other networks, like 10.6.X.Y, etc.
I thought the point of a Management interface was that you could set things up in such a way that the Management interface
was the only way you could access the firewall, and you did not have to have IP addresses on the Gig interfaces,
(at least not in transparent mode, for NAT you obviously would have to)
I tried to add a static route entry to 10.6.X.Y , but
when I typed "route.." my only available destination interfaces were either TrustedNetwork or UnTrustedNetwork ??
How do I configure the Management interface for non-local subnets to be reachable on the firewall in transparent mode?

transparent firewall is configured differently from routed mode.
here's a basic config required:
firewall transparent (erases the current config; does not require a reboot)
interface BVI1
ip address 192.168.10.10 255.255.255.0
interface GigabitEthernet0
nameif outside
bridge-group 1
security-level 0
interface GigabitEthernet1
nameif inside
bridge-group 1
security-level 100
route outside 0.0.0.0 0.0.0.0 192.168.10.254
route inside 10.0.0.0 255.0.0.0 192.168.10.100
I think that you need a BVI interface with an IP address before the ASA starts forwarding traffic
The old syntax (pre 8.3 or 8.2 not sure) forces only 2 interfaces and no BVI was configured... the IP was assigned in global config.
Hope that helps,
Patrick

ASA Transparent mode multicast traffic in 8.2 and 8.4

Hi,
When i configure 8.2 in trasparent mode and deploy the a network that was wrok on EIGRP after that i found the neighborship was stop when i allow the mutlicast address and prtocol on outside interface it was start the working But when i deploy an ASA with 8.4 IOS and then allow the multicast address and protocol both the interface (Inside and outside) after that it was start working.
So i want to know that what the reasion to allow multicast address and protocol on 8.4 IOS for both interface. I am not able to find any answer for this.

Hi Mahesh,
By default ASA in transparent mode do not allow any packets not having a valid EtherType greater than or equal to 0x600. As per my knowledge this concept remain same for all versions of ASA. Most control plane protocols are denied.
ASA in transparent mode only allows ARP, broadcast traffic, TCP and UDP inspected unicast traffic.
For EIGRP to work through transparent firewall, we need to open ACLs in both direction for multicast and unicast both type of EIGRP traffic on all versions of ASA Firewall.

Trying to figure out whether I can use an ASA cluster in Transparent mode to facilitate VRF based network ??

Hi Guys,
I had to re-post this here because I did not get any comments earlier.. hopefully I'll get something here.. :)
I'm investigating the ways that I can use 2 x ASA (5525x) to accommodate Multi-tenancy situation with overlapping addresses. Unfortunately in this particular scenario we have to stick with 5525x firewalls.
The ASAs are going to be placed in north-south traffic path between 2 routers and these routers need to be configured with multiple VRFs to segregate the traffic for each tenant with overlapping IP subnets ( We are not looking at NAT as a workaround for the time being).
As we know, this ASA model won't support VRFs so we can't use the ASA as a intermediary routing hop and therefore this is not an option.. and using security contexts per VRF seems not scale-able enough (correct me if I'm wrong). So my thinking is that, if we put the ASAs in to the transparent mode and just use the ASAs as a layer 2 interconnect (configured with different VLANs connecting VRFs served by top and bottom routers) I should be able to go up to maximum of 50 VRFs (since 5525x only supports 200 VLANs).
I'm also planning to use the 2 ASAs in a cluster mode to aggregate the bandwidth of both ASAs for better throughput.
So I need to clarify following with you guys..
1) Can I actually do this or am I missing something.
2) Are there any limitations that I might run in to with this setup
3) Is there anyone out there who's doing the same thing or can you think of a better way to tackle this scenario (with same hardware and requirements)
4) Instead of using clustering, can I use simple Active/Stanby pare and still configure transparent mode and use it that way ?
Appreciate your input.
Thanks
Shamal

There is a limitation on how many context you can have, which depends on the license you have. This is quite possible with ASA multi routed mode and even with multi transparent mode. You can have overlapping ip in each context without the need of using nat as long as you have unique mac address for each sub interface.
Thanks

INPUT textfield does not show non-English letters with transparent mode

INPUT textfield does not show non-English letters when i
type, if transparent mode turn on
this is bug of Flash Player 9?
will this bug had be fixed?

I just tested Firefox and Chrome on linux, i doesn't work either, but i get different weird chars: Ã©Ã¨Ã§a
However, on both mac and linux, if i copy the chars and paste them in the input field, it passes.

Explain about transparent mode, single mode, multiple context mode

You can explain about the differents of transparent mode, single mode, multiple context mode in ASA 5500? Thank you very much.

Great question. Hope the below helps:
Transparent Mode: In this mode, the ASA will filter traffic without requiring L3 on the ASA. This means that in your config you will not put IPs on the interfaces to be used for traffic filtering. Thus, filtering is transparent to the traffic as the traffic isn't directly routed to the firewall. Think of it like you have a server plugged into a switch. In transparent mode, you place the ASA between the server and the switch and no configuration change is required to the server. In routed mode, you place the ASA in the same physical location between the server and switch, but have to change the server to use the ASA as a default gateway.
Single Mode: Default mode of an ASA. The ASA acts as a single firewall and all interfaces are provisioned to be managed through a single firewall configuration.
Multiple Context Mode: The ASA is split into multiple virtual configurations. With the ASA now virtualized, you provision the physical interfaces on the ASA to the virtual firewall configured. Each context has it's own configuration seperate from the rest of the firewall. Multi-context is meant for enterprises to invest in a single piece of hardware and scale it for use as multiple security devices.
Hope this helps. Let me know if you have anymore questions!
-Mike
http://cs-mars.blogspot.com

I do have Apple Cinema 23" transparent mod. M8536 but I have to clue how to connect it to PC or current versions of MAC

I do have Apple Cinema 23" transparent mod. M8536 but I have to clue how to connect it to PC or current versions of MAC

You will need a DVI to ADC adapter
<http://www.amazon.com/Apple-DVI-ADC-Display-Adapter/dp/B00011KHT2>
If the computer does not have DVI, you will also need another adapter to connect the DVI plug to the computer.

Connectivity Issues Cisco ASA 5515 in Transparent Mode

Hi,
we´re having problems with one transparent mode setup at one customer site. The ASA is equiped with a CX Module, but we´re not using it, so far in the service policy rules it was enabled and matched all traffic, but in "monitor only" mode. There is a global acl that allows any-any-IP.
Firewall-Info:
- ASA Version 9.1(2)
- Interfaces gi0/0 + gi0/2 without any interface errors
The ASA 5515x is configured as a "bump in the wire". In general our setup is working but with beginning of the installation of the firewall the customer faces following connection issues, without the firewall no problems:
- Connections to SAP-Servers behind the MPLS begin to drop, affected all users
- Incoming monitoring sessions (ping/snmp) from central management are facing ping timeouts, connection timeouts
- http downloads are stopping, Customer: it will stop responding and the download will fail.
In general the customer describes it this way: "We do not have the best connection here so once we connected the firewall all the problems are magnified"
I recognized, that we unconfigured the default inspection during initial setup and reconfigured this entry for the cx module. So the the default inspection with all the settings are not present any more... How important are these settings? One phenomen is, that I´ve seen a large numbers of concurrent connections that increased over time. And we already had that situation, that the firewall reached the max-conn count.
Should I try to reconfigure the default inspection, as it ships from factory? And whats the best way to check for problems? What can be the reason for the dropping connections?
I attached a network plan and the firewall config, hopefully, that somebody has an idea. Of course I can provide additional information...
Best Regards
Sebastian

Hi Vibhor,
thanks for your reply. Does this also affect the traffic, even the setting is set to "Monitor Only" ?
Is it recommend to configure the default-inspection rule as a default setting?
Further Question: I´ve read sth. about, that service policy rules must be "reloaded" to take effect, after they have been changed. Is that right and how do I reload them?
Here is an output from sh asp drop, do I have to care about certain values? This values result from two connected users doing some downloads over a 2Mbit connection.
ciscoasa# show asp drop
Frame drop:
Invalid encapsulation (invalid-encap) 10
First TCP packet not SYN (tcp-not-syn) 114
TCP failed 3 way handshake (tcp-3whs-failed) 3
TCP RST/FIN out of order (tcp-rstfin-ooo) 18
Dst MAC L2 Lookup Failed (dst-l2_lookup-fail) 33
L2 Src/Dst same LAN port (l2_same-lan-port) 260
FP L2 rule drop (l2_acl) 2958
Interface is down (interface-down) 9420
No management IP address configured for TFW (tfw-no-mgmt-ip-config) 117
Dropped pending packets in a closed socket (np-socket-closed) 66
Thanks
Sebastian

Failure when FWSM in transparent mode with multiple contexts

hi experts,
We have two FWSMs working in active/standby state, configured with multiple contexts in transparent mode. and the "outside" and "inside" interfaces for each context are in same subnet.
Now we have one FWSM broken and the RMA part can't arrived in short time, so we have the risk that the sencond FWSM could be failed as well. In the worst case if the two was broken or powered off simultaneously, i wonder that if the communications between multiple contexts could be ok???
thanks in advance.

The software requirements for Cisco Secure ACS are dependent on the type of Extensible Authentication Protocol (EAP) desired. For full support of all the EAP types including EAP-Flexible Authentication via Secure Tunneling (FAST), use release 3.2.3 or higher.
http://www.cisco.com/en/US/netsol/ns340/ns394/ns431/ns434/networking_solutions_implementation_guide09186a008038906c.html

VRF issue with Firewall in transparent Mode.

Hi Guys,
I have 7609 Router and 6513 L3 Switch connected Through ASA 5545.
I am running Multiple VRF between router and Switch and BGP routing Protocol. When they are connected directly to each other everything is normal, however, when I have connected them via ASA 5545 then everything fails. I am using ASA in transparent Mode.
My question is: Do ASA require different setting in case of VRF? If yes, then please give me sample config.

I have taken following output from Firewall will this be any help?
sh interface ouTSIDE
Interface GigabitEthernet0/1 "OUTSIDE", is up, line protocol is up
Hardware is i82574L rev00, BW 1000 Mbps, DLY 10 usec
        Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)
        Input flow control is unsupported, output flow control is off
        MAC address 7c69.f68f.df78, MTU 1500
        IP address 175.4.8.35, subnet mask 255.255.255.248
        8435 packets input, 680680 bytes, 0 no buffer
        Received 8135 broadcasts, 0 runts, 0 giants
        0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
        0 pause input, 0 resume input
        8138 L2 decode drops
        0 packets output, 0 bytes, 0 underruns
        0 pause output, 0 resume output
        0 output errors, 0 collisions, 1 interface resets
        0 late collisions, 0 deferred
        0 input reset drops, 0 output reset drops
        input queue (blocks free curr/low): hardware (476/461)
        output queue (blocks free curr/low): hardware (511/511)
Traffic Statistics for "OUTSIDE":
        297 packets input, 118503 bytes
        0 packets output, 0 bytes
        297 packets dropped
      1 minute input rate 0 pkts/sec, 13 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 6 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
ciscoasa# show asp drop
Frame drop:
FP L2 rule drop (l2_acl)                                                   297
ASA Version 9.0(1)
firewall transparent
ciscoasa# show module all
Mod Card Type                                    Model              Serial No.
0 ASA 5545-X with SW, 8 GE Data, 1 GE Mgmt     ASA5545
ips ASA 5545-X IPS Security Services Processor   ASA5545-IPS
Mod MAC Address Range                 Hw Version   Fw Version   Sw Version
0 7c69.f68f.df77 to 7c69.f68f.df80 1.0          2.1(9)8      9.0(1)
ips 7c69.f68f.df75 to 7c69.f68f.df75 N/A          N/A          7.1(4)E4
Mod SSM Application Name           Status           SSM Application Version
ips IPS                            Up               7.1(4)E4
Mod Status             Data Plane Status     Compatibility
0 Up Sys             Not Applicable
ips Up                 Up
Mod License Name   License Status Time Remaining
ips IPS Module     Enabled         perpetual
ciscoasa#
I have create Ehtertype ACL and permit any traffic.
cdp traffic has passed through but I am still not able to ping :(

ASR5k transparent mode

Hi,
in order to configure transparent mode in ASR5k to disable authentication and to allow everyone what is the appropriate commandso co
in SAMI module we used used to configure 'access-mode non-transparent' under the APN
what is the equivalent in ASR5k?
we have configured the following 2 commands and we still have authentication failure for the GTP user
aaa authentication subscriber none
apn {apn_name}
authentication allow-noauth

Hi,
If you use transparent instead of server or client, there should be no problem wit copy run start. (The difference is that in this case your switch doesn't participate in the VTP communication, only forward the received messages and doesn't update its vtp db).
During the copy running-config startup-config did you get some error message? (not enough space or something) PLease first check the flash with the show flash command.
Or try to save your running to flas not to startup config: copy running flash:test.cfg
If you need more help please send me output of show flash at least...
bye
FCS
Please rate me if I helped.

My mac goes to reduced transparency mode at startup

My Mac Goes Into Reduced Transparency Mode Even On Login Page

Reset PRAM. http://support.apple.com/kb/PH18761
Start up in Safe Mode. http://support.apple.com/kb/PH18760
Best.

SCA Transparent Mode

At a customer site any traffic running from the SCA through their CSS shows the SCA as the source IP in the server logs. I need to be able to set this up so the customer can see the real source address from their clients. I followed the docs on how to do one armed transparent mode but I obviously missed something or did something incorrectly. Attached are the configs.

could you tell us what's wrong.
Is it still using its own ip or you have no connectivity ?
The CSS config is also very important.
Did you configure correctly the default gateways ?
[one pointing at the SCA and one to the router].
Is the default gateway of the server set to the CSS ?
If you can't make it work, use a sniffer trace to understand the traffic flow.
For reference, here is a link to the config
http://www.cisco.com/en/US/products/hw/contnetw/ps2083/products_configuration_example09186a00801bbf4e.shtml
Regards,
Gilles.

Cisco WSA : Is it possible to use web proxy in transparent mode without WCCP router ?

Hello !
I would like to use Cisco WSA as a web proxy in a transparent way (without any configuration in client's web browsers) but i don't have a WCCP router. So, is it possible ?
If yes, how to do this ?
Thank you,
Stephane Walker

Hi Stephane
The only alternative to WCCP is PBR (Policy Based Routing). With a simple configuration on the router you can redirect traffic defined as interesting by access list to WSA. On the WSA you need to configure transparent mode (Security Services -> Web Proxy -> Edit Settings -> Proxy Mode: Transparent). You also need to assure that proxy is listening on the port 80 and that HTTPS proxy is enabled (on port 443) if you want to redirect the HTTPS traffic as well.
Sample configuration for Cisco router
access-list 110 permit tcp any any eq www
route-map proxy-redirect permit 10
match ip address 110
set ip next-hop xxx.xxx.xxx.xxx
interface ethernet0/1
ip policy route-map proxy-redirect
xxx.xxx.xxx.xxx is the proxy IP in such case and access-list 110 defines web traffic (HTTP TCP/80) as interesting.
The biggest disadvantage of such solution is lack of failure detection. If the proxy will go down for some reason router will keep redirecting the traffic causing internet access outage.
Routers other than Cisco equipment should also have an option to configure policy based routing.
/Artur
Ps. It's not possible to place the WSA in-line between clients and the internet.

Authorware 7 Transparent mode

Similar Messages

Maybe you are looking for