Auto dialer not calling out

Hi
I have a water alarm that I can connect to my BT phone line. It will call the programmed numbers if there is a water leak.
However, I can't get it to call out using my BT phone line.
I have taken the devie round to a friend's house and tried it on their phone line - it works perfectly.
I live in a flat (as does the friend I tested it with). I have also tried it in another flat in the block who has a BT line and it also didn't work using theirs.
I have broadband from PlusNet.
I can make and receive calls perfectly using my phone - it is just the auto dialer that doesn't work.
Can anyone help? Could there be a problem with my line that is stopping the auto dialer from working. Maybe it dials the numbers too quickly for my line - although it does work at my friend's place.
Many thanks
rigby44

The dialler must be set to use tone dialling and not loop disconnect.
Loop disconnect will quite often fail if the circuit has broadband on it, as the broadband filters distort the DC pulses.
Loop disconnect will not be supported on the future 21CN phone network, and manufacturers have been told to phase it out.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Similar Messages

Auto dial not working

Auto dial not working
I'm using an iPad 4, with WiFi and Cellular and iOS 8.1.3
In the past if I was searching for a hotel and found one I only had to tap on the phone number and it would dial using either Skype or MagicJack. It worked using Wi-Fi or my data plan. It was an absolutely valuable function especially when traveling.
Now, when I click on a phone number, it says that it's going to exit the program (like Safari) and start a new program. When I click, Ok, nothing happens.
I must have inadvertently changed some setting.
Skype works, MagicJack works, but I must dial the number manually.
I have tried turning "Handoff" off and on then rebooting, turning FaceTime off and on and rebooting (and every combination of those two programs and actions).
To say the least, I am frustrated because it must be something obvious. (to everyone else!)
Any ideas as to how to how I can get it to dial automatically again?
Thanks for any assistance.

IPAD user guide for IOS 8 is available on line at apple -
you can download it in IBOOK or PDF format to refer to when you can't get connected to see it on-line
http://support.apple.com/manuals
Handoff is only for using with multiple devices - Iphone/Ipad/ipod
This is the bit in Handoff on Phone calls
Phone calls
If your iPhone (with iOS 8) is nearby, you can make and receive phone calls on your other iOS devices and Mac computers. All devices must be on the same Wi-Fi network, and signed into FaceTime and iCloud using the same Apple ID.
Make a phone call on iPad. Tap a phone number in Contacts, Calendar, or Safari. You can also tap a recent contact in the multitasking screen.
Disable iPhone Cellular Calls. On your iPhone, go to Settings > FaceTime, then turn off iPhone Cellular Calls.
You may have to use Face Time to make calls from the IPAD -- there are page or 2 on that --

Our facetime will not call out - ipad mini

My ipad mini will not call out....using email address??? Appears to be activated.....

Are you trying to message another Apple device? Is that device iMessage activated?
Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
http://tinyurl.com/a7odey8
Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
Using FaceTime and iMessage behind a firewall
http://support.apple.com/kb/HT4245
iOS: About Messages
http://support.apple.com/kb/HT3529
Set up iMessage
http://www.apple.com/ca/ios/messages/
Troubleshooting Messages
http://support.apple.com/kb/TS2755
Setting Up Multiple iOS Devices for iMessage and Facetime
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
FaceTime and iMessage not accepting Apple ID password
http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
Unable to use FaceTime and iMessage with my apple ID
https://discussions.apple.com/thread/4649373?tstart=90
 Cheers, Tom

Why can i not call out when in roaming but can recieve calls

why can i not call out when roaming and my data shuts off but i can recieve calls

rhondahuffman1,
These are great question and we definitely want to help out! For starters, what model of device are we working with? Are you roaming outside of the country or is the device stating roaming within certain areas? What's your zip code? Happening in specific locations? Share some details, so that we may assist.
AdamG_VZW
Follow us on Twitter @VZWSupport

IPhone will not call out

my phone will not call out please help!!!

Have you contacted your provider to inquire if they are having network issues?
This really isn't an iPhone issue... it's a network issue.

My iphone 5 for some reason can receive calls, send & receive texts but can not call out

My iphone 5 for some reason can receive calls, send & receive texts but can not call out

I am not sure if this issue is going to help you but lets give it a try.
I know that where im from, which is the Netherlands, I am not able to sent e-mails from my iPhone or any other mobile device by using 3G or a random WIFI acces point. The provider only allowes you to sent e-mails when you are connected to a network of there own. Which means if you have provider "101" and your email settings are set up for this provider in your iPhone but your using the network of a friend of yours which is provider "202" you cannot sent emails from his network. Though you can receive them you may not sent.
As I said, I am not aware if this issue is the same for you totaly depents on the country and provider your using.

Sykpe will not call out

Everytime I dial a mobile number on Skype it makes the dial tone then cuts the call off. I have just recently topped the credit up so this cannot be the issue - I have also used it previously and it has been fine - any suggestions as to why i'm having this problem?

Have you contacted your provider to inquire if they are having network issues?
This really isn't an iPhone issue... it's a network issue.

Iphone5 will not call or receive calls.

Iphone5 will not call out or receive in coming calls. Text and data work fine. Was working. Went to canada noted it was not working. Returned to US and still not working.

Let's get your phone working FairwayFatty. Please try going to Settings> Toggle Airplane Mode ON then back OFF. Also go to General>Cellular> Cellular Data-ON> Enable LTE-ON.
Please keep us posted.
Thank you,
VanessaS_VZW
Follow us on Twitter @VZWSupport

Iphone 4s won't call out or receive calls or messages

got my self a iPhone 4s off my friend locked on Vodafone phone was working fine to I got it unlocked after a few days it just kept on saying call ended right away. I was so confuse I try every thing to sort it out and I mean everything even went to Apple store and they done all there tests and said I need a new phone as it has hardware problems and I need to pay £160 for a replacement phone as my warranty run out = ( and you think I'm going to pay that when I just bought this phone off my friend noooooo way .... I thought I try one last thing as I had full t-Mobile signal and 3G and Internet but could not call out or receive calls so weird anyway I thought I'd put a Vodafone chip back in the phone as it's was locked on Vodafone before and see what happens and guess what no service so that got me thinking that the phone has been blocked . So I phoned up Apple and give you IME number to see if it was blacklisted and they said it ain't ?????? So what now well I got my friend to call Vodafone up to see if they blacklisted it and guess what there did as my friend lost the new phone they got and Vodafone decided to block both serial numbers how fun for me not. so now they have un blacklisted my phone and it works just fine = ) lucky I did not pay apple for a phone hey don't believe everything they say and don't give up

Good morning. Recently I had the same problem - I could not access the cellular data network. I was informed by our local Internet Service Provider that, every so often, the phone (iPhone 4S) would reset itself. In so doing, it purges some information that is really needed. The ISP had to walk me through the steps to re-entering that info; after that, it worked just fine. She said that they have instruction cards available at the ISP's office, and that I should go get one for future reference. It may be a problem connected with relatively small providers – it's not a nationwide carrier, like Sprint or AT&T. She asked me, "Didn't they tell you about that when you bought the phone?" Well, of course not. Live and learn!

Why can't I call out when I'm in Mongolia? I can receive calls and send and receive text messages.

I'm currently in Mongolia and can not call out from my iPhone 4S using a Mobicom SIM card. I can receive calls and send and receive texts. I use my regular SIM card from Canada and it works fine. It worked fine 6 months ago.

Having incorrect APN settings shouldn't be stopping text message from coming though. But to get the correct APN setting just delete any APN profiles on the device. And the EE ones should just get installed but you can just to make sure use the link that has posted.
You don't need a online account to top-up unless your using the account to top-up through.
CLICK HERE FOR OTHER WAYS TO TOP-UP
with text messages not coming through I have to ask are you getting a signal ?

Cannot call out

I upgraded my 4 to a 4S and moved my number over. Gave my son the 4S and the Verizon store gave him a new number on that phone. His phone will receive calls, but not call out. We resent whole phone and it started calling out for 1 day and then stopped again?
>>Subject line shortened<<
Message was edited by: Verizon Moderator

FallDodd,
Thanks for the info. There are no reports of any troubles in the zip code that you provided. It appears to be specific to your device rather than network. Have you added anything new to the phone recently? The next step I would recommend taking would be to reset your network settings;
http://vz.to/1lyaSQh .
Please let us know if you still need further assistance.
TrevorC_VZW
Follow us on Twitter @VZWSupport

CALL DOES NOT ROUTE OUT THE LOCAL GATEWAY

Local calls will not route out the local Gateway of branch1 to the PSTN or from the PSTN back to branch1, however they will route out either CorpHQ or branch2 backup gateways. When I go into the route group configuration for branch1, and remove the backup gateways, I get a fast busy tone when I dial the local number. I know the MGCP Gateway at branch1 is functioning because when I dial 911 and run debug ISDN Q931, the call routes properly through branch1, so I have a call routing problem. I ran DNA and it came back as ROUTE THIS PATTERN and all of the number translations looked accurate, so I didn't have to check for any block patterns. I'm not getting any errors on the calling party phone display. When I deleted the route pattern for the branch1 site and forced it to use the global route pattern, I received a debug output on branch1. I do not know a debug command (such as debug voip dial-peer or debug ccsip messages) to use for an MGCP Gateway to see if the call is actually reaching the Gateway.
I have checked the following:
the route pattern configuration
the translation pattern configuration
the called party transformation pattern configuration
the route list configuration to make sure the correct route group for branch1 was selected
the route group configuration to make sure that the branch1 Gateway was first in the order of selected devices
the route pattern configuration to make sure the correct route list for branch1 ist selected
the Gateway configuration to make sure it's using the device pool for branch1 and to make sure the called party transformation CSS for the branch1 Gateway is applied
the device pool configuration to make sure it's using the route group branch1
Any assistance would be greatly appreciated
Regards,
Ron

Hi Nishant:
Please see the attachments for the Gateway pages
The significant digits for inbound calls for all 3 gateways is '4'
Please see the running-configs of the 3 gateways and the PSTN
Please see the debugs for the INBOUND calls
Many Thanks,
Ron
The following INBOUND call from the PSTN to 2065011001 is now working, however it is supposed to be routing through CorpHQ and is instead routing through Branch1. Please see 'DEBUG VOIP CCAPI INOUT' & 'DEBUG ISDN Q931'
Branch1#
ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x0096
        Cause i = 0x8290 - Normal call clearing
//22/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x16, digit_event=0x0, enable=FALSE, consume=FALSE)
//22/5A001212800B/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=22
//22/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x16, disp=0, digit_event=0x0, enable=FALSE, consume=FALSE)
//22/5A001212800B/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=22
//22/5A001212800B/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms))
//22/5A001212800B/CCAPI/ccGenerateToneInfo:
   Stop Tone On Digit=FALSE, Tone=Null,
   Tone Direction=Network, Params=0x0, Call Id=22
//23/5A001212800B/CCAPI/ccGetCallStatistics:
   Call Stats=0x4A5346FC, Call Id=23
//22/5A001212800B/CCAPI/ccConferenceDestroy:
   Conference Id=0xC, Tag=0x0
//22/xxxxxxxxxxxx/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0xC, Source Interface=0x49E07FD4, Source Call Id=22,
   Destination Call Id=23, Disposition=0x0, Tag=0x0
//23/xxxxxxxxxxxx/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0xC, Source Interface=0x495BABA4, Source Call Id=23,
   Destination Call Id=22, Disposition=0x0, Tag=0x0
//22/5A001212800B/CCAPI/cc_generic_bridge_done:
   Conference Id=0xC, Source Interface=0x495BABA4, Source Call Id=23,
   Destination Call Id=22, Disposition=0x0, Tag=0x0
//22/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//22/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
//22/5A001212800B/CCAPI/cc_api_get_transfer_info:
   Transfer Number Is Null
//23/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//23/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
//23/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x495BABA4, Tag=0x0, Call Id=23,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
//23/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 4821DDE8
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 1
//22/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x49E07FD4, Tag=0x0, Call Id=22,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
//22/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 4821DEC8
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 0
ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x8096
ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0096
ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0097
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA18381
                Preferred, Channel 1
        Progress Ind i = 0x8183 - Origination address is non-ISDN
        Display i = 'Seattle US Phone'
        Calling Party Number i = 0x4180, '2065015111'
                Plan:ISDN, Type:Subscriber(local)
        Called Party Number i = 0xC1, '2065011001'
                Plan:ISDN, Type:Subscriber(local)
//-1/xxxxxxxxxxxx/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x49E07FD4, Interface Type=6, Destination=, Mode=0x9,
   Call Params(Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=, FinalDestinationFlag=FALSE, Outgoing Dial-peer=0, Call Count On=FALSE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=D000000002f5368f000000F580000097)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 1
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1210179280,feature_id:24
//24/74820328800C/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=6, FlowMode=1
//24/74820328800C/CCAPI/ccCallSetContext:
   Context=0x4A524790
//-1/xxxxxxxxxxxx/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x495BABA4, Interface Type=9, Destination=0.0.0.0, Mode=0x9,
   Call Params(Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=, FinalDestinationFlag=FALSE, Outgoing Dial-peer=0, Call Count On=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=D000000002f5368f000000F580000097)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 2
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1210179056,feature_id:25
//25/74820328800C/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=9, FlowMode=1
//25/74820328800C/CCAPI/ccCallSetContext:
   Context=0x4A524580
//25/74820328800C/CCAPI/cc_api_call_connected:
   Interface=0x495BABA4, Data Bitmask=0x0, Progress Indication=NULL(0),
   Connection Handle=0
//25/74820328800C/CCAPI/cc_api_call_connected:
   Call Entry(Connected=TRUE, Responsed=TRUE, Retry Count=0)
//24/74820328800C/CCAPI/cc_api_call_proceeding:
   Interface=0x49E07FD4, Progress Indication=NULL(0)
//24/74820328800C/CCAPI/cc_api_call_connected:
   Interface=0x49E07FD4, Data Bitmask=0x1, Progress Indication=DESTINATION IS NON ISDN(2),
   Connection Handle=0
//24/74820328800C/CCAPI/cc_api_call_connected:
   Call Entry(Connected=TRUE, Responsed=TRUE, Retry Count=0)
//24/74820328800C/CCAPI/ccCallModify:
   Nominator=0x1000, Params=0x4A2E7368, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x18, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x18, disp=0, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=15000(ms), Inter Digit Timeout=10000(ms))
//24/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID1=0x18, callID2=0x19, tag=0x0)
//24/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID1=0x18, gcid=0-0-0-0, tag=0x0)
//25/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID2=0x19, gcid=0-0-0-0, tag=0x0)
//24/74820328800C/CCAPI/ccConferenceCreate:
   Conference Id=0x4A2E757C, Call Id1=24, Call Id2=25, Tag=0x0
//24/xxxxxxxxxxxx/CCAPI/cc_api_bridge_done:
   Conference Id=0xD, Source Interface=0x49E07FD4, Source Call Id=24,
   Destination Call Id=25, Disposition=0x0, Tag=0xFFFFFFFF
//25/xxxxxxxxxxxx/CCAPI/cc_api_bridge_done:
   Conference Id=0xD, Source Interface=0x495BABA4, Source Call Id=25,
   Destination Call Id=24, Disposition=0x0, Tag=0x0
//24/74820328800C/CCAPI/cc_generic_bridge_done:
   Conference Id=0xD, Source Interface=0x495BABA4, Source Call Id=25,
   Destination Call Id=24, Disposition=0x0, Tag=0x0
//24/74820328800C/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0xD, Destination Call Id=25)
//25/74820328800C/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0xD, Destination Call Id=24)
//24/74820328800C/CCAPI/cc_api_caps_ind:
   Destination Interface=0x495BABA4, Destination Call Id=25, Source Call Id=24,
   Caps(Codec=0x1, Fax Rate=0x1, Vad=0x1,
   Modem=0x2, Codec Bytes=20, Signal Type=3)
//24/74820328800C/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
//25/74820328800C/CCAPI/cc_api_caps_ind:
   Destination Interface=0x49E07FD4, Destination Call Id=24, Source Call Id=25,
   Caps(Codec=0x4, Fax Rate=0x2, Vad=0x1,
   Modem=0x0, Codec Bytes=20, Signal Type=2)
//25/74820328800C/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
//25/74820328800C/CCAPI/cc_api_caps_ack:
   Destination Interface=0x49E07FD4, Destination Call Id=24, Source Call Id=25,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=9314)
//24/74820328800C/CCAPI/cc_api_caps_ack:
   Destination Interface=0x495BABA4, Destination Call Id=25, Source Call Id=24,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=9314)
//24/74820328800C/CCAPI/cc_api_call_modify_done:
   Result=0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_voice_mode_event:
   Call Id=24
//24/74820328800C/CCAPI/cc_api_voice_mode_event:
   Call Entry(Context=0x4A524790)
//24/74820328800C/CCAPI/cc_process_notify_bridge_done:
   Conference Id=0xD, Call Id1=24, Call Id2=25
//24/74820328800C/CCAPI/ccSetDigitTimeouts:
   Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms)
//24/74820328800C/CCAPI/ccSetDigitTimeouts:
   Call Entry(Inter Digit Timeout=4000(ms), Initial Digit Timeout=4000(ms))
//24/74820328800C/CCAPI/ccRestartDigitTimeoutMsec:
   Digit Timeout=0, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x18, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x18, disp=0, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms))
ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8097
        Channel ID i = 0xA98381
                Exclusive, Channel 1
//24/74820328800C/CCAPI/ccCallModify:
   Nominator=0x1000, Params=0x4A2E6E68, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_modify_done:
   Result=0, Interface=0x49E07FD4, Call Id=24
ISDN Se0/0/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x8097
        Progress Ind i = 0x8088 - In-band info or appropriate now available
//24/74820328800C/CCAPI/ccGenerateToneInfo:
   Stop Tone On Digit=FALSE, Tone=Ring Back,
   Tone Direction=Network, Params=0x0, Call Id=24
//24/74820328800C/CCAPI/cc_handle_inter_digit_timer:
   Generate inter-digit timeout CC_EV_CALL_DIGIT_END event
The following INBOUND call from the PSTN to 5126022001 fails and is supposed to be routing through Branch1 and is instead routing through CorpHQ. Please see 'DEBUG VOIP CCAPI INOUT'
CorpHQ#
//-1/A31ADF52800B/CCAPI/cc_api_display_ie_subfields:
   cc_api_call_setup_ind_common:
   cisco-username=
   ----- ccCallInfo IE subfields -----
   cisco-ani=5126026222
   cisco-anitype=4
   cisco-aniplan=1
   cisco-anipi=0
   cisco-anisi=0
   dest=5126022001
   cisco-desttype=4
   cisco-destplan=1
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-lastrdn=
   cisco-rdntype=-1
   cisco-rdnplan=-1
   cisco-rdnpi=-1
   cisco-rdnsi=-1
   cisco-redirectreason=-1   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
//-1/A31ADF52800B/CCAPI/cc_api_call_setup_ind_common:
   Interface=0x49F42894, Call Info(
   Calling Number=5126026222,(Calling Name=)(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed),
   Called Number=5126022001(TON=Subscriber, NPI=ISDN),
   Calling Translated=FALSE, Subscriber Type Str=RegularLine, FinalDestinationFlag=TRUE,
   Incoming Dial-peer=1, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), Calling IE Present=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=-1
//-1/A31ADF52800B/CCAPI/ccCheckClipClir:
   In: Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed)
//-1/A31ADF52800B/CCAPI/ccCheckClipClir:
   Out: Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 1
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1241383960,feature_id:13
//13/A31ADF52800B/CCAPI/cc_api_call_setup_ind_common:
   Set Up Event Sent;
   Call Info(Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed),
   Called Number=5126022001(TON=Subscriber, NPI=ISDN))
//13/A31ADF52800B/CCAPI/cc_process_call_setup_ind:
   Event=0x497D0010
//-1/xxxxxxxxxxxx/CCAPI/cc_setupind_match_search:
   Try with the demoted called number 5126022001
//13/A31ADF52800B/CCAPI/ccCallSetContext:
   Context=0x4A131A54
//13/A31ADF52800B/CCAPI/cc_process_call_setup_ind:
   >>>>CCAPI handed cid 13 with tag 1 to app "_ManagedAppProcess_Default"
//13/A31ADF52800B/CCAPI/ccCallProceeding:
   Progress Indication=NULL(0)
//13/A31ADF52800B/CCAPI/ccCallDisconnect:
   Cause Value=1, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//13/A31ADF52800B/CCAPI/ccCallDisconnect:
   Cause Value=1, Call Entry(Responsed=TRUE, Cause Value=1)
//13/A31ADF52800B/CCAPI/cc_api_get_transfer_info:
   Transfer Number Is Null
//13/A31ADF52800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x49F42894, Tag=0x0, Call Id=13,
   Call Entry(Disconnect Cause=1, Voice Class Cause Code=0, Retry Count=0)
//13/A31ADF52800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 49FE0410
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 0
PSTN#sh run
Building configuration...
Current configuration : 13975 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname PSTN
boot-start-marker
boot-end-marker
card type e1 0 0
card type t1 0 1
logging message-counter syslog
no aaa new-model
clock timezone EST -5
clock summer-time EST recurring
network-clock-participate wic 0
network-clock-participate wic 1
no network-clock-participate aim 0
dot11 syslog
ip source-route
ip cef
no ip domain lookup
ip domain name att.com
ip name-server 177.1.100.110
ip multicast-routing
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-ni
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redirect ip2ip
fax protocol cisco
sip
bind control source-interface Loopback10
bind media source-interface Loopback10
header-passing
voice translation-rule 101
rule 1 /^\+.*/ //
rule 2 /^501.*/ //
rule 3 /^1206.*/ //
rule 4 /^00.*/ //
rule 5 /^0011.*/ //
rule 6 /^206/ /1206/
rule 7 /^1512.*/ /\0/
rule 8 /^011$.*$/ /\1/
voice translation-rule 102
rule 1 /^1$2065015111$$/ /\1/ type any subscriber plan any isdn
rule 2 /^1$2065015555$$/ /\1/ type any subscriber plan any isdn
rule 3 /^1$2065015151$$/ /\1/ type any subscriber plan any isdn
rule 4 /^1$5126026222$$/ /\1/ type any national plan any isdn
rule 5 /^31670357575$/ /&/ type any international plan any isdn
rule 6 /^31207037333$/ /&/ type any international plan any isdn
rule 7 /^31107047444$/ /&/ type any international plan any isdn
rule 8 /^911$/ /&/ type any unknown plan any unknown
rule 9 /^15126022.../ /&/ type any unknown plan any unknown
rule 10 /^31207033.../ /&/ type any unknown plan any unknown
rule 11 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 103
rule 1 /^206.*/ /&/ type any subscriber plan any isdn
rule 2 /^1/ // type any national plan any isdn
rule 3 /^00/ // type any international plan any isdn
voice translation-rule 201
rule 1 /^\+.*/ //
rule 2 /^602.*/ //
rule 3 /^1512.*/ //
rule 4 /^00.*/ //
rule 5 /^0011.*/ //
rule 6 /^512/ /1&/
rule 7 /^1206.*/ /&/
rule 8 /^011$31.*$/ /\1/
voice translation-rule 202
rule 1 /^1$5126026222$$/ /\1/ type any subscriber plan any isdn
rule 2 /^1$2065015555$$/ /\1/ type any national plan any isdn
rule 3 /^1$2065015151$$/ /\1/ type any national plan any isdn
rule 4 /^1$2065015111$$/ /\1/ type any national plan any isdn
rule 5 /^31670357575$/ /&/ type any international plan any isdn
rule 6 /^31207037333$/ /&/ type any international plan any isdn
rule 7 /^31107047444$/ /&/ type any international plan any isdn
rule 8 /^911$/ /&/ type any unknown plan any unknown
rule 9 /^12065011.../ /&/ type any unknown plan any unknown
rule 10 /^31207033.../ /&/ type any unknown plan any unknown
rule 11 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 203
rule 1 /^512.*/ /&/ type any subscriber plan any isdn
rule 2 /^1/ // type any national plan any isdn
rule 3 /^00/ // type any international plan any isdn
voice translation-rule 301
rule 1 /^\+.*/ //
rule 2 /^20.*/ //
rule 3 /^0$[1-8].*$/ /31\1/
rule 4 /^011/ //
rule 5 /^0031/ //
rule 6 /^703..../ /3120&/
rule 7 /^00$1.*$/ /\1/
voice translation-rule 302
rule 1 /^31207037333$/ /7037333/ type any subscriber plan any isdn
rule 2 /^7033$...$$/ /0207033\1/
rule 3 /^911$/ /112/ type any unknown plan any unknown
rule 4 /^31$670357575$$/ /0\1/ type any national plan any isdn
rule 5 /^31$107047444$$/ /0\1/ type any national plan any isdn
rule 6 /^12065015555$/ /&/ type any international plan any isdn
rule 7 /^12065015151$/ /&/ type any international plan any isdn
rule 8 /^12065015111$/ /&/ type any international plan any isdn
rule 9 /^15126026222$/ /&/ type any international plan any isdn
rule 10 /^12065011...$/ /&/ type any unknown plan any unknown
rule 11 /^15126022...$/ /&/ type any unknown plan any unknown
rule 12 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 303
rule 1 /^703.*/ /&/ type any subscriber plan any isdn
rule 2 /^010/ // type any national plan any isdn
rule 3 /^1/ // type any international plan any isdn
voice translation-rule 1000
rule 1 /.*$1...$$/ /206501\1/
rule 2 /.*$2...$$/ /512602\1/
rule 3 /.*$45..$$/ /020757\1/
voice translation-rule 1001
rule 1 /^1206...5...$/ /+&/
rule 2 /^1512...6...$/ /+&/
rule 3 /^31.0...7...$/ /+&/
voice translation-profile 1-HQ-Change_DNIS-Check_ANI
translate called 101
voice translation-profile 1-HQ-Proper_Types
translate calling 102
translate called 103
voice translation-profile 2-BR1-Change_DNIS-Check_ANI
translate called 201
voice translation-profile 2-BR1-Proper_Types
translate calling 202
translate called 203
voice translation-profile 3-BR2-Change_DNIS-Check_ANI
translate called 301
voice translation-profile 3-BR2-Proper_Types
translate calling 302
translate called 303
voice translation-profile SIP-NORMALIZE-DNIS-ANI
translate calling 1001
translate called 1000
voice-card 0
dspfarm
archive
log config
hidekeys
controller E1 0/0/0
clock source internal
pri-group timeslots 1-3,16
description == Voice Circuit to Branch2
controller T1 0/1/0
clock source internal
cablelength long 0db
pri-group timeslots 1-3,24
description == Voice Circuit to CorpHQ
controller T1 0/1/1
clock source internal
cablelength long 0db
pri-group timeslots 1-3,24
description == Voice Circuit to Branch1
interface Loopback0
ip address 177.1.254.254 255.255.255.255
interface Loopback10
ip address 177.1.254.250 255.255.255.255
interface Loopback11
ip address 177.1.254.251 255.255.255.255
interface FastEthernet0/0
description ==TO INTERNET==
ip address 192.168.1.150 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
description === To HQ
ip address 177.1.19.1 255.255.255.0
duplex auto
speed auto
interface Serial0/0/0:15
description == PRI Circuit to R3-BR2
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
isdn negotiate-bchan resend-setup
no isdn outgoing ie network-facility
isdn outgoing display-ie
no cdp enable
interface Serial0/1/0:23
description == PRI Circuit to R1-HQ
no ip address
encapsulation hdlc
isdn switch-type primary-5ess
isdn protocol-emulate network
isdn incoming-voice voice
isdn negotiate-bchan
isdn outgoing display-ie
no cdp enable
interface Serial0/1/1:23
description == PRI Circuit to R2-BR1
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
isdn supp-service name calling
isdn negotiate-bchan resend-setup
isdn outgoing ie network-facility
no cdp enable
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.1.1
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
control-plane
voice-port 0/0/0:15
translation-profile incoming 3-BR2-Change_DNIS-Check_ANI
description == Voice PRI to Branch2
voice-port 0/1/0:23
translation-profile incoming 1-HQ-Change_DNIS-Check_ANI
description == Voice PRI to CorpHQ
voice-port 0/1/1:23
translation-profile incoming 2-BR1-Change_DNIS-Check_ANI
description == Voice PRI to Branch1
dial-peer voice 1 pots
description == All inbound calls from HQ BR1 BR2 into PSTN
incoming called-number .
direct-inward-dial
dial-peer voice 101 pots
description == Subscriber Calls from PSTN into CorpHQ
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^2065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 102 pots
description == National Calls from PSTN into CorpHQ
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^12065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 103 pots
description == International Calls into CorpHQ from PSTN Coming from NL Ph
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^0012065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 104 pots
description == + Calls into CorpHQ from PSTN Coming from Mobiles
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern +12065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 201 pots
description == Subscriber Calls from PSTN into Branch1
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^5126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 202 pots
description == National Calls from PSTN into Branch1
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^15126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 203 pots
description == International Calls into Branch1 from PSTN Coming from NL Ph
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^0015126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 204 pots
description == + Calls into Branch1 from PSTN Coming from Mobiles
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern +15126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 301 pots
description == Subscriber Calls from PSTN into Branch2
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^7033...$
direct-inward-dial
port 0/0/0:15
forward-digits 7
dial-peer voice 302 pots
description == National Calls from PSTN into Branch2
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^0207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 10
dial-peer voice 303 pots
description == International Calls into Branch2 from PSTN Coming from US Ph
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^01131207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 304 pots
description == International Calls into Branch2 from PSTN Coming from US Ph
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^31207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 305 pots
description == + Calls into Branch2 from PSTN Coming from Mobiles
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern +31207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 1000 voip
description == Calls into AT&T SIP ITSP for VC Week1 Lab1
rtp payload-type nse 99
rtp payload-type nte 100
voice-class sip localhost dns:sip1.att.com
session protocol sipv2
incoming called-number .
dtmf-relay rtp-nte
codec g711ulaw
dial-peer voice 5000 voip
service aa
destination-pattern A5000
session target ipv4:177.1.254.254
incoming called-number A5000
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
num-exp 1888....... 911
num-exp 1900....... 911
num-exp 1976....... 911
num-exp 1777....... 911
num-exp 1444....... 911
num-exp 0800....... 911
num-exp 0900....... 911
sip-ua
telephony-service
no auto-reg-ephone
max-ephones 1
max-dn 10
ip source-address 177.1.254.254 port 2000
caller-id block code *67
system message You WILL PASS this Exam!
voicemail A5000
max-conferences 8 gain -6
call-forward pattern .T
dn-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp 7960 Sep 01 2012 15:29:37
ephone-dn 1 dual-line
number 12065015111 secondary +12065015111
label Seattle, US +1 206 501 5111
description INE PSTN Phone
name Seattle US Phone
ephone-dn 2 dual-line
number 15126026222 secondary +15126026222
label Austin, US +1 512 602 6222
name Austin TX Phone
ephone-dn 3 dual-line
number 31207037333 secondary +31207037333
label Amsterdam, NL +31 20 703 73 33
name Amsterdam NL Phone
ephone-dn 4 dual-line
number 12065015555 secondary +12065015555
label Hurley Mobile +1 206 501 5555
name Hurley's Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 5 dual-line
number 12065015151 secondary +12065015151
label Hurley's Home +1 206 501 5151
name Hurley's Home
call-forward busy A5000
call-forward noan A5000 timeout 12
ephone-dn 6 dual-line
number 31670357575 secondary +31670357575
label Sawyer's Mobile +31 6 70357575
name Sawyer's Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 7 dual-line
number 911 secondary 112
label US/EU Emer/FreePhone/Prem
name Emergency Services
ephone-dn 8 dual-line
number 15126026262 secondary +15126026262
label BLinus Mobile +1 512 602 6262
name Benjamin Linus Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 9 dual-line
number 31207037373 secondary +31207037373
label DHume Home +31 20 703 73 73
name Desmond Hume Home
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 10 dual-line
number 31107047444 secondary +31107047444
label Rotterdam, NL +31 10 704 74 44
name Rotterdam NL Phone
ephone 1
device-security-mode none
mac-address A456.3040.0DAA
type 7975
button 1:1 2:2 3:3 4:10
button 5:6 6o7,8,5,4
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
ntp source Loopback0
ntp master 10
ntp server 64.90.182.55
end
CorpHQ#sh run
Building configuration...
Current configuration : 6353 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname CorpHQ
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone PST -8
clock summer-time PDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 177.1.11.1 177.1.11.14
ip dhcp excluded-address 177.1.11.21 177.1.11.254
ip dhcp excluded-address 177.2.11.1 177.2.11.14
ip dhcp excluded-address 177.2.11.21 177.2.11.254
ip dhcp pool CorpHQ-Phones
   network 177.1.11.0 255.255.255.0
   option 150 ip 177.1.10.10 177.1.10.20
   default-router 177.1.11.1
   dns-server 177.1.100.110
ip dhcp pool Branch1-Phones
   network 177.2.11.0 255.255.255.0
   option 150 ip 177.1.10.10 177.1.10.20
   default-router 177.2.11.1
   dns-server 177.1.100.110
no ip domain lookup
ip multicast-routing
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-ni
voice service voip
allow-connections h323 to h323
fax protocol cisco
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
no update-callerid
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice translation-rule 1
rule 1 // // type any subscriber plan any isdn
voice translation-rule 2
rule 1 // // type any national plan any isdn
voice translation-rule 3
rule 1 // // type any international plan any isdn
voice translation-rule 10
rule 1 /^[2-9].........$/ /9&/
rule 2 /^1[2-9].........$/ /9&/
rule 3 /^011/ /9&/
voice translation-profile MakeInternational
translate called 3
voice translation-profile MakeNational
translate called 2
voice translation-profile MakeSubscriber
translate called 1
voice translation-profile Prefix9_InFrom_CUCM
translate called 10
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller T1 0/0/0
pri-group timeslots 1-3,24
description == Voice Circuit to PSTN
interface Loopback0
ip address 177.1.254.1 255.255.255.255
ip pim dense-mode
interface FastEthernet0/0
description == To CorpHQ-Switch
no ip address
duplex auto
speed auto
interface FastEthernet0/0.10
description == Server VLAN
encapsulation dot1Q 10
ip address 177.1.10.1 255.255.255.0
ip pim dense-mode
interface FastEthernet0/0.11
description == Voice VLAN
encapsulation dot1Q 11
ip address 177.1.11.1 255.255.255.0
ip helper-address 177.1.10.10
ip nbar protocol-discovery
ip pim dense-mode
interface FastEthernet0/0.12
description == Data VLAN
encapsulation dot1Q 12
ip address 177.1.12.1 255.255.255.0
interface FastEthernet0/0.13
description == PSTN PHONE VLAN
encapsulation dot1Q 13
ip address 177.1.13.1 255.255.255.0
interface FastEthernet0/1
description === To PSTN
ip address 177.1.19.254 255.255.255.0
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 36
cdp enable
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To BR1
bandwidth 384
ip address 177.0.101.1 255.255.255.0
ip pim dense-mode
snmp trap link-status
frame-relay interface-dlci 101
ip rsvp bandwidth 136
interface Serial0/1/0.2 point-to-point
description == FR To BR2
ip address 177.0.201.1 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 102
ip rsvp bandwidth 136
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 177.1.19.1
ip route 0.0.0.0 0.0.0.0 FastEthernet0/0.10
no ip http server
no ip http secure-server
control-plane
voice-port 0/0/0:23
voice-port 0/3/0
voice-port 0/3/1
ccm-manager music-on-hold
sccp local Loopback0
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 1 register CorpHQ-729-MTP
associate profile 2 register CorpHQ-711-MTP
associate profile 3 register CorpHQ-HW-Xcode
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
codec ilbc
maximum sessions 2
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
dial-peer voice 10 pots
translation-profile outgoing MakeSubscriber
destination-pattern 911
no digit-strip
port 0/0/0:23
dial-peer voice 11 pots
translation-profile outgoing MakeSubscriber
destination-pattern 9[2-9]..[2-9]......$
port 0/0/0:23
dial-peer voice 12 pots
translation-profile outgoing MakeNational
destination-pattern 91[2-9]..[2-9]......$
port 0/0/0:23
forward-digits 11
dial-peer voice 13 pots
translation-profile outgoing MakeInternational
destination-pattern 9011T
port 0/0/0:23
prefix 011
dial-peer voice 100 voip
description == Inbound/Outbound SIP PSTN GW From/To CUCM Pub
translation-profile incoming Prefix9_InFrom_CUCM
destination-pattern ^2065011...$
voice-class codec 1
session protocol sipv2
session target ipv4:177.1.10.10
incoming called-number .
ip qos dscp cs3 signaling
dial-peer hunt 1
sip-ua
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
ntp source Loopback0
ntp master 2
ntp server 177.1.254.254
end
Branch1#sh run
Building configuration...
Current configuration : 3838 bytes
! Last configuration change at 01:19:02 CDT Thu Oct 10 2013
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname Branch1
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone CST -6
clock summer-time CDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
dot11 syslog
ip source-route
ip cef
ip multicast-routing
no ipv6 cef
ntp update-calendar
ntp server 177.1.254.1
multilink bundle-name authenticated
isdn switch-type primary-ni
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller T1 0/0/0
pri-group timeslots 1-3,24 service mgcp
interface Loopback0
ip address 177.1.254.2 255.255.255.255
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.11
description == Voice VLAN
encapsulation dot1Q 11
ip address 177.2.11.1 255.255.255.0
ip helper-address 177.1.254.1
ip pim dense-mode
interface FastEthernet0/0.12
description == Data VLAN
encapsulation dot1Q 12
ip address 177.2.12.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn supp-service name calling
isdn bind-l3 ccm-manager
isdn outgoing ie facility
isdn outgoing display-ie
isdn outgoing ie redirecting-number
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 37
cdp enable
no frame-relay inverse-arp
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To HQ
ip address 177.0.101.2 255.255.255.0
ip pim dense-mode
snmp trap link-status
frame-relay interface-dlci 101
ip rsvp bandwidth 136
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
voice-port 0/0/0:23
ccm-manager fallback-mgcp
ccm-manager redundant-host 177.1.10.10
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
mgcp
mgcp call-agent 177.1.10.20 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp fax t38 ecm
mgcp bind control source-interface Loopback0
mgcp bind media source-interface Loopback0
mgcp profile default
sccp local Loopback0
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 3 register Br1-HW-Xcode
associate profile 1 register Br1-729-MTP
associate profile 2 register Br1-711-MTP
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
end
Branch2#sh run
Building configuration...
Current configuration : 5789 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname Branch2
boot-start-marker
boot system flash:c2800nm-advipservicesk9-mz.124-24.T7.bin
boot system flash:
boot-end-marker
card type e1 0 0
logging message-counter syslog
no aaa new-model
clock timezone CEST 1
clock summer-time CEDT recurring
network-clock-participate wic 0
no network-clock-participate aim 0
dot11 syslog
ip source-route
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
no supplementary-service h225-notify cid-update
fax protocol cisco
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class custom-cptone JOIN-TONE
dualtone conference
frequency 300 3600
cadence 150 100 500
voice class custom-cptone LEAVE-TONE
dualtone conference
frequency 300 3600
cadence 500 100 150
voice translation-rule 1
rule 1 /^7033...$/ /020&/
voice translation-rule 10
rule 1 /^0/ /0&/
voice translation-rule 200
rule 1 /^206501...$/ /1&/
voice translation-profile 7DigitDNIS-to-10Digit
translate called 1
voice translation-profile Prefix0_InFrom_CUCM
translate called 10
voice translation-profile Prefix1-toCorpHQ-ANI
translate calling 200
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller E1 0/0/0
pri-group timeslots 1-3,16
description == Voice Circuit to PSTN
controller E1 0/0/1
interface Loopback0
ip address 177.1.254.3 255.255.255.255
h323-gateway voip bind srcaddr 177.1.254.3
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.11
encapsulation dot1Q 11
ip address 177.3.11.1 255.255.255.0
ip helper-address 177.1.10.10
interface FastEthernet0/0.12
encapsulation dot1Q 12
ip address 177.3.12.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bchan-number-order ascending
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 37
cdp enable
no frame-relay inverse-arp
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To HQ
ip address 177.0.201.2 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 102
ip rsvp bandwidth 136
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
interface Service-Engine1/0
no ip address
shutdown
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
control-plane
voice-port 0/0/0:15
translation-profile incoming 7DigitDNIS-to-10Digit
ccm-manager music-on-hold
sccp local Loopback0
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 4 register Br2-HW-Conf
associate profile 3 register Br2-HW-Xcode
associate profile 2 register Br2-711-MTP
associate profile 1 register Br2-729-MTP
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 4 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 1
conference-join custom-cptone JOIN-TONE
conference-leave custom-cptone LEAVE-TONE
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
dial-peer voice 10 pots
destination-pattern 112
no digit-strip
port 0/0/0:15
dial-peer voice 11 pots
destination-pattern 00[1-9]T
port 0/0/0:15
prefix 0
dial-peer voice 12 pots
translation-profile outgoing Prefix1-toCorpHQ-ANI
destination-pattern 000T
port 0/0/0:15
prefix 00
dial-peer voice 100 voip
description == Inbound/Outbound H323 PSTN GW From/To GK and CUCM Pub
translation-profile incoming Prefix0_InFrom_CUCM
destination-pattern 0207033...$
voice-class codec 1
session target ipv4:177.1.10.10
incoming called-number .
ip qos dscp cs3 signaling
dial-peer voice 101 voip
description == Outbound H323 PSTN GW To CUCM Sub
destination-pattern 0207033...$
voice-class codec 1
session target ipv4:177.1.10.20
ip qos dscp cs3 signaling
dial-peer hunt 1
telephony-service
max-ephones 1
max-dn 1
ip source-address 177.1.254.3 port 2000
max-conferences 8 gain -6
moh test.au
multicast moh 239.2.1.1 port 16384 route 177.1.254.3 177.3.11.1
transfer-system full-consult
create cnf-files version-stamp 7960 Sep 13 2013 18:55:27
line con 0
exec-timeout 0 0
line aux 0
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
login
scheduler allocate 20000 1000
ntp source Loopback0
ntp update-calendar
ntp server 177.1.254.1
end

N73 auto dial out???

Hello all,
Anyone has experienced N73 auto dial out without the owner/user knowing that it is dialling out to valid phone numbers? I have checked the auto-redial and this feature is not activated. So i am wondering if anyone of you have experience this problem before?

Hi,
I am getting the same problem with my N73. But the thing is it is redialling when i am on one call. It is auto dialling the last dialled call, even while i am still on the call.
For example, I have tried a number earlier & now also i am calling the same number means, then the same number is dialled again. This is happeneing to me only when I have connected my headset with the mobile.
More over in most cases, i am unable to dial a number immediately. Sometimes it takes 4 to 5 times to make a call. If i dial, it automatically disconnects.
Is it a firmware problem?
Nokia team has to reply for this issue. I am getting annoyed because of this.
Will Nokia make any update in the next firmware update to give a autolock facility? Because of this, i am forced to install AUTOLOCK software and I dont like that too.Message Edited by bkar81 on 28-Sep-200708:08 AM

Can we translate in captivate 7? I Have tried and changed the Caption and Notes. Can we change the on screen text of te normal slides, interactive call out boxes, screen recording slides and quizzes? If yes, please let me know the process.

Can we translate in captivate 7? I Have tried and changed the Caption and Notes. Can we change the on screen text of te normal slides, interactive call out boxes, screen recording slides and quizzes? If yes, please let me know the process.

Of course! Here ya go
For the record, I did create a new project with only two slides to try and duplicate the issue. I had the same problem. I unchecked the Mouse Click Sound check box, republished and the slide auto advanced. I'm wondering if a default sound file was somehow moved or deleted? I discussed uninstalling and reinstalling C7 onto my laptop, but that's a frustrating solution haha

Can call out but not receiving calls

I can call out to any number but when you dial the phone number(yes it is the right #) it says phone not in service.

We have had the same problem for almost a year now. We can call out, and the number is correct. Cannot receive any calls, message says number not in service. Meanwhile I have to pay both AT&T and Comcast so I don't lose my number. When I call Comcast I am told the problem is not on their side. I will be calling the Illinois Commerce Hotline and filing a complaint against Comcast. I have asked for a credit on my bill, since I am not receiving the service I am paying for, and no response from Comcast. Maybe a lawsuit is in my future for failure to provide services that were paid for.

Auto dialer not calling out

Similar Messages

Maybe you are looking for