Auto provsioning with wcs and 4404 controlers

i'm about to add several new controlers to my network and would like to use the Auto provisioning feature to help out.
the only problem i have is i havn't got involved in setting up the DHCP on a the network that is managed by our server team so i need to be able to tell them which opttion i need to us to point a new controller to the TFTP server on the WCS to get its configuration.
a quick guide to the setup is, the controllers are on 1 subnet, the wcs is one server on another subnet and the DHCP is on a second server. the router sitting in the middle of all this has the ip helper address set to point to the dhcp server and the controllers are picking up an ip address but not their config.
any ideas guessing as i said it's a DHCP option need setting.
Many Thanks,
Adam

configure S6,S15 and S66
You should mention the config file in any of the following name in the tftp server
controllermac-config,serialno-config, ciscowlc-config,ciscowlc.cfg
Make sure you have a service port connectivity to the controller

Similar Messages

Rogue AP - Not in sync with WCS and WLC

WCS - 7.0.164.0 and WLC - 7.0.98.0.
For some reason, I am seeing rogue ap alert on WLC and am not seeing on WCS. How do I clean up database and sync with WCS and WLC.
I am seeing same thing with coverage holes.
- Allen -

Allen,
On the WLC go to Management > SNMP > Trap Controls, make sure that you have the traps checked.
HTH,
Steve
*Please remember to rate helpful posts*

License problem with WCS and WLC

Hi All,
I have planned to implement three WLCs and one WCS to manage them.
AP count is as below :-
     WLC #1     -     10 AP
     WLC #2     -     10 AP
     WLC #3     -     20 AP
When WLC #1 is down that connected 10 APs should failover to the WLC #3.
So at normal scenarion, WLC #3 should need 30 AP license; to failover WLC#1 APs properly to the WLC #3
My problem is, Can I load total AP license (40 license) to WCS without installing them to individual WLCs ?
If it is possible i can cut off the additional 10 AP license, required to the HA and failover.
or if I use a WCS may i need to buy additional 40 license to WCS seperately from 40 WLC license ?
Thanks,
Charith

Yes, you required to have seperate licences for WLC & WCS.
You cannot add WLC licence to WCS & vice versa.
HTH
Rasika

Auto reconnect with Oracle and Hibernate ?

Hello,
Does anyone know i can configure Hibernate to connect automatically to an Oracle base in the case of a cut network.
Thanks,
Djelloul OMRANE
[email protected]

Google's time
http://www.hibernate.org/56.html

Blocking a MAC address with WCS

I recently deployed a 4404 with WCS and want to block a MAC address from connecting to our wireless because of Deauth floods. We have around 40 APs. I am thinking it should be done through a template, but not sure. Can anyone lead me to right document that explains the process of blocking specific MAC addresses?
thanks,
Jonathan

Hi Jonathan,
Have you see this doc;
Configuring a MAC Filter Template
Cisco Wireless Control System Configuration Guide, Release 4.0
http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00806b7273.html#wp1068145
Hope this helps!
Rob
Please remember to rate helpful posts.....

I like the idea of auto back-up for my new iMac, Ipad and PC Netbook, particularly if I can access all files and data stored on any device. But I have a Conceptronic router. Will Time Capsule work with this and how?

I like the idea of auto back-up for my new iMac, Ipad and PC Netbook, particularly if I can access all files and data stored on any device. But I have a Conceptronic router.
1. Will Time Capsule work with this and how?
2. Can my printer USB be plugged in and then shared between the devices?
3. Can I create a network and how?
4. What happend when a visitor logs onto my existing wireless router?
I'm new to Macs (well a returning user having started with Mac Plus!!) and not very technical. Any help / advice will be much appreciated.
Ray

The key to what you seem to want to do is to be able to get Apple's Time Capsule router to "join" the network that your Conceptronic router. I believe that works with some third-party routers, but I've never seen a list of those that work in such a configuration and I have no experience with Conceptronic equipment.
You might be better off with a Network-Attached Storage (NAS) device instead of a Time Capsule.

GenerationType.AUTO doesn't work correctly with Kodo and MySQL

Greetings,
I'm migrating applications from JBoss/Hibernate to WebLogic/Kodo. The following column annotation:
@Id
@Column(name="CUSTOMER_ID")
@GeneratedValue(strategy = GenerationType.AUTO)
public long getCustomerId()
is supposed to generate auto-increment primary key in mysql. This is what happens with Hibernate. With Kodo, this seems to be equivalent with GenerationType.TABLE as a table named openjpa_sequence_table is created, containing sequence values. So what should one do in order to be able to use true auto-increment strategy with MySQL and Kodo ?
Many thanks in advance,
Nicolas

Hi Nicolas,
By setting the generation strategy to AUTO, you're essentially letting the JPA provider choose which strategy to use. It looks like Kodo is using the TABLE strategy by default and Hibernate is using the IDENTITY strategy here. You can set the strategy to IDENTITY if you want Kodo to behave similarly to Hibernate. However, it's worth pointing out that there may be a reason for Kodo not using the IDENTITY strategy by default.
The docs at: http://edocs.bea.com/wls/docs103/kodo/full/html/ref_guide_pc_oid.html#ref_guide_pc_oid_pkgen_autoinc
point out the following:
"Statements inserting into tables with auto-increment / identity columns cannot be batched. After each insert, Kodo must go back to the database to retrieve the last inserted auto-increment value to set back in the persistent object. This can have a negative impact on performance. "
- Matt

Cannot get new messages to download automatically and auto reply with out of office message have to manually check for new messages to get it to do this

I am using Mozilla Thunderbird 31.3.0. I know how to create a message filter to set up an auto reply message, but cannot get Mozilla to automatically download new message and auto reply with the message in the filter unless I manually check for new messages, that is the only way to make it work. I have looked online and can't seem to find an answer to this particular issue. According to anything that I have found, I have the correct boxes checked in server settings: check for new messages at startup, automatically check for new messages, check for new messages every x amount of minutes. It's one thing to have to leave my computer on and Thunderbird open to make this work, but to have to manually check for new messages to get the auto response to work defeats the whole purpose of having an auto reply, as I use them for vacations, holidays, etc. I have wondered if there are any security settings that are causing this issue, but if so, I don't know what changes to make to them. Thanks in advance for any help. This is driving me crazy.

I do find it a bit odd that Thunderbird is not getting mail on schedule, perhaps you have an add-on or anti virus program that prevents that.
Holding shift while you start Thunderbird will start with add-ons disabled to check if mail come automatically.
Airmail is right though, use Verizons auto responder. This link might help with that http://www.verizon.com/support/residential/internet/highspeed/account+tools/email+tools/questionsone/85621.htm#
You say that not having such a setting in Thunderbird is something that needs fixing. This idea comes on the whole because Outlook has such an option. what most people are not aware of it only works with Exchange server. There is no "vacation response" in server mail specifications so every server implements it differently.
Just as all cars have a radiator, you can not take any radiator and just put it in, they are subtly different even though they perform the same purpose. Same goes for the various vacation responders, They perform the same purpose but they differ between email server software brands.
Thunderbird leaves it to the server end to expose the functionality, as they are really the only ones who understand what they did. Outlook exposes the option and mostly greys it out.

How to monitor traffic and associations per AP with WCS?

Hi,
is there a way to get traffic and client access/associations data with WCS for each AP of a centrally managed WLAN?
I manage a campus WLAN with a 4402 WLC (software version 6.0.188.0) and a WCS version 6.0.170.0 .
WCS provides me detailed information on a client basis: I'm able to know the association history of each client currently
connected, both which AP the client has connected to, and how much traffic the client has generated/received for each connection.
I hadn't find a way to get the same information on an AP basis. Namely, which clients have been connected, and how much traffic
has been transmitted per time slot.
I suppose this is just a matter of making a different query to the WCS database, since the data are the same used for providing
the information on the client association and traffic history. Though, I haven't find a way on WCS to get this information.
Thanks a lot in advance for any help, cheers,
Piero

Use the client reports from WCS reporting:
http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/6_0reps.html#wp1134645
The Client Summary report contains four sub reports. Each of them can be independently customized. The following information is default information available from a Client Summary report depending on the customizable report selected:
•Number of Sessions
•Number of Total Users
•Number of Unique Users
•Number of New Users
•Number of Unique APs
•Number of Users per AP
•Total Traffic (MB)
•Average Traffic per Session (KB) and per user (in KB)
•Total Throughput (Mbps)
•Average Throughput per Session and per user (Mbps)
•Protocol—802.11a/n or 802.11b/g/n.
•SSID—The user-defined Service Set Identifier name
•VLAN
•Vendor
•User Count
•Time Used (Minutes)
•Traffic (MB)
•Session Count
•% of Users
•% of Time
•% of Traffic
•% of Session
•Total Time of a session

Location Appliance 2700 - is it supported with v7 WCS and WLC?

The compatibility matrix shows no support for a Location Appliance 2700 for any version 7.0.x.x for WCS and WLC. However, I did see a thread here where a v6.0.x.0 had compatibility. v6.0.202.0 is MD. Is it compatible with v7 WCS and WLC?
Can any of the experts please comment? Thank you.

Hi,
here is the link that will answer ur question!!
http://www.cisco.com/en/US/docs/wireless/controller/4400/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp78062
Please dont forget to rate the usefull posts!!
Regards
Surendra

Vlan management with WLC and WCS

I'd like to know if it is possible to use the same vlan for the management of the WCS and for configuring a wlan?
I try to make this lab and when I declare a dynamic interface that is in the same subnet as the WCS ip address, the reliability between controler and WCS is lost.

I know that I should not put servers on the same vlan as wireless client but I just want to know if it is possible or if Cisco implemented something to avoid this to understand why my lab didn't work with this configuration.
Thanks

DB and listner auto start with linux problem

Dear all :
i can't set DB auto start with linux
my db version 10g linux 5
I followed these steps :
edit the "/etc/oratab" file setting the restart flag for each instance to 'Y'.
TSH1:/u01/app/oracle/oracle/product/10.2.0/db_1:Y
create a file called "/etc/init.d/dbora" as the root user, containing the following.
#!/bin/sh
# chkconfig: 345 99 10
# description: Oracle auto start-stop script.
# Set ORA_HOME to be equivalent to the $ORACLE_HOME
# from which you wish to execute dbstart and dbshut;
# Set ORA_OWNER to the user id of the owner of the
# Oracle database in ORA_HOME.
ORA_HOME=/u01/app/oracle/oracle/product/10.2.0/db_1
ORA_OWNER=oracle
if [ ! -f $ORA_HOME/bin/dbstart ]
then
echo "Oracle startup: cannot start"
exit
fi
case "$1" in
'start')
# Start the Oracle databases:
# The following command assumes that the oracle login
# will not prompt the user for any values
su - $ORA_OWNER -c "$ORA_HOME/bin/lsnrctl start"
su - $ORA_OWNER -c $ORA_HOME/bin/dbstart
'stop')
# Stop the Oracle databases:
# The following command assumes that the oracle login
# will not prompt the user for any values
su - $ORA_OWNER -c $ORA_HOME/bin/dbshut
su - $ORA_OWNER -c "$ORA_HOME/bin/lsnrctl stop"
esac
chmod 750 /etc/init.d/dbora
chkconfig --level 345 dbora on
# ln -s /etc/init.d/dbora /etc/rc.d/rc3.d/K01dbora
# ln -s /etc/init.d/dbora /etc/rc.d/rc3.d/S99dbora
# ln -s /etc/init.d/dbora /etc/rc.d/rc5.d/K01dbora
# ln -s /etc/init.d/dbora /etc/rc.d/rc5.d/S99dbora

Follow this part of Oracle Doc,
Automating Shutdown and Startup
http://download.oracle.com/docs/cd/B19306_01/server.102/b15658/strt_stp.htm#sthref249
Also run your script manually see if it will run sucessfully.
/etc/init.d/dbora start
/etc/init.d/dbora stop

Auto replacing my tag brackets with lt and gt :(

Hi everyone,
I have an Interactive report that converts some '<a href ...>X</a>' text of mine by replacing the '<' and '>' with '&lt' and '&gt'. How can I make it so that a link is actually embedded (a link that says 'X'), rather than what shows up as '<a href ...>X</a>'
This OTN thread covers it somewhat: Re: issue with html in sql - < is replaced to &lt ; - but the 'column formatting' (called report attributes for me) doesn't have a 'display as html' option:(
Edited by: user10225290 on Jan 21, 2009 9:26 AM

Hi,
Is the content of the column just the URL you want to link to?
I have just tested creating an Interactive Report using:
SELECT EMPNO,
'<a href="f?p=' || v('APP_ID') || ':11:' || v('SESSION') || '">' || EMPNO || '</a>' EMPNO_LINK,
ENAME
FROM EMPand the second column showed up, and works as, a proper link.
Andy

With iDVD, how can I create a DVD that auto plays on insert and then loops?

I want to burn a presentation using idvd which will be played at an exhibition. how do I create a dvd without menu that auto plays upon insert and then loops?
Thanks
Message was edited by: Host <to clarify Subject>

To create a OneStep DVD:
Connect your DV camcorder to your computer and set the camera to VTR, VCR, or Play mode. Turn on your camcorder if it doesn't turn on automatically.
Open iDVD and click the OneStep DVD button. (If iDVD opens to a recent project, choose File > OneStep DVD.)
Insert a recordable DVD disc.
iDVD rewinds the tape in the video camera and captures the video.
------------or-------------
To burn a OneStep DVD from a folder:
Choose File > "OneStep DVD from Movie."
Locate the movie you want to add in the dialog that opens, then click Import.
Insert a blank DVD disc into the optical drive.
This kind of disc is sometimes called "kiosk mode" and is a good way to create demos or other presentations that play automatically and require no user interaction.

An issue with authentication and authorization on ISE 1.2

Hi, I'm new to ISE.
I have an issue with authentication and authorization.
I have ISE 1.2 plus patch 6 installed on VMware.
I have built-in Windows XP supplicant and 2960 cisco switch with IOS c2960-lanbasek9-mz.150-2.SE5.bin
On supplicant I use EAP(PEAP) with EAP-MSCHAP v2.
I created authentication and authorization rules with Active Directory as External Identity Source. Also I applied authorization profile with DACL.I login on Windows XP machine under different Active Directory accounts. Everything works fine (authentication, authorization ), but only for several hours. After several hours passed , authentication and authorization stop working . I can see that ISE trying authenticate and authorize users, but ISE always use only one account for authentication and authorization . Even if I login under different accounts ISE continue to use only one last account.
I traied to reboot switch and PC,but it didn’t help. Only rebooting of ISE helps. After ISE rebooting, authentication and authorization start to work properly for several hours.
I don’t understand is it a glitch or I misconfigured ISE or switch, supplicant?
What should I do to resolve this issue?
Switch configuration:
testISE#sh runn
Building configuration...
Current configuration : 7103 bytes
! Last configuration change at 12:20:15Tue Apr 15 2014
! NVRAM config last updated at 10:35:02 Tue Apr 15 2014
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname testISE
boot-start-marker
boot-end-marker
no logging console
logging monitor informational
enable secret 5 ************
enable password ********
username radius-test password 0 ********
username admin privilege 15 secret 5 ******************
aaa new-model
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa authorization auth-proxy default group radius
aaa accounting update periodic 5
aaa accounting dot1x default start-stop group radius
aaa server radius dynamic-author
client 172.16.0.90 server-key ********
aaa session-id common
clock timezone 4 0
system mtu routing 1500
authentication mac-move permit
ip dhcp snooping vlan 1,22
ip dhcp snooping
ip domain-name elauloks
ip device tracking probe use-svi
ip device tracking
epm logging
crypto pki trustpoint TP-self-signed-1888913408
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1888913408
revocation-check none
rsakeypair TP-self-signed-1888913408
crypto pki certificate chain TP-self-signed-1888913408
dot1x system-auth-control
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
ip ssh version 2
interface FastEthernet0/5
switchport mode access
ip access-group ACL-ALLOW in
authentication event fail action next-method
authentication event server dead action reinitialize vlan 1
authentication event server alive action reinitialize
authentication host-mode multi-auth
authentication open
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
authentication violation restrict
mab
dot1x pae authenticator
dot1x timeout tx-period 10
spanning-tree portfast
interface FastEthernet0/6
switchport mode access
ip access-group ACL-ALLOW in
authentication event fail action next-method
authentication event server dead action reinitialize vlan 1
authentication event server alive action reinitialize
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
authentication violation restrict
mab
dot1x pae authenticator
dot1x timeout tx-period 10
spanning-tree portfast
interface FastEthernet0/7
interface Vlan1
ip address 172.16.0.204 255.255.240.0
no ip route-cache
ip default-gateway 172.16.0.1
ip http server
ip http secure-server
ip access-list extended ACL-ALLOW
deny icmp any host 172.16.0.1
permit ip any any
ip radius source-interface Vlan1
logging origin-id ip
logging source-interface Vlan1
logging host 172.16.0.90 transport udp port 20514
snmp-server community public RO
snmp-server community ciscoro RO
snmp-server trap-source Vlan1
snmp-server source-interface informs Vlan1
snmp-server enable traps snmp linkdown linkup
snmp-server enable traps mac-notification change move
snmp-server host 172.16.0.90 ciscoro
radius-server attribute 6 on-for-login-auth
radius-server attribute 6 support-multiple
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server dead-criteria time 5 tries 3
radius-server vsa send accounting
radius-server vsa send authentication
radius server ISE-Alex
address ipv4 172.16.0.90 auth-port 1812 acct-port 1813
automate-tester username radius-test idle-time 15
key ******
ntp server 172.16.0.1
ntp server 172.16.0.5
end

Yes. Tried that (several times) didn't work. 5 people in my office, all with vers. 6.0.1 couldn't access their gmail accounts. Kept getting error message that username and password invalid. Finally solved the issue by using Microsoft Exchange and "m.google.com" as server and domain and that the trick. Think there is an issue with imap.gmail.com and IOS 6.0.1. I'm sure the 5 of us suddently experiencing this issue aren't the only ones. Apple will figure it out. Thanks.

Auto provsioning with wcs and 4404 controlers

Similar Messages

Maybe you are looking for