Auto-tune method

For the auto-tune in the MAX, I wanna to ask how many counts that the motors should be runned?
Can I change the desired position?
Regards,
Ivan

The count value depends on the resolution of your motor. Set it to be the maximum counts you want your motor to travel while responding to the signal sent for auto-tuning. Take a look at the following tutorial for more detailed information on servo tuning:
http://zone.ni.com/devzone/conceptd.nsf/webmain/4B7775373E4AE64986256B6000691505
Hope this helps -
Julie S
Applications Engineer
National Instruments

Similar Messages

RZ21 Auto Alert Method

Hi,
I have followed the SAP help portal and OSS note 176492 to setup alert monitoring in client 000. I wanted to create a single alert to send emails when the sapreorg on the CEN filesystem reaches the precentage used threshold levels. The pre-reqs done are:
- SAPconnect has been configured in client 000, tested and works successfully.
- solution landscape has been configured successfully.
- CCMS agents deployed and configured in RZ21.
I have done the following to setup alert monitoring:
RZ21 -> Configure central system -> Assign central autoreactions
create new central Auto reaction using the named as a Z name Z_CCMS_ALERT_FS_USED by using CCMS_OnAlert_Email_V2 as a template and setup according to note 176492.
select SAP SID, select MTE called "Filesystems" and selected my Z auto reaction and click save which now appears at the bottom. I now setup a monitor in DSWP -> solution monitoring for that landscape and system and set the threshold levels, data collected every 100 seconds and click save. After this i go into RZ20 and select
SAP CCMS Monitor Templates -> filesystems -> and select my sapreorg MTE.
to test this i take a copy of a redo log and place it in the sapreorg directory and copy it a couple of times to trigger the threshold alert. After a couple of refreshes in RZ20 the MTE alert for sapreorg changes to red, which also shows on the DSWP solution monitoring dashboard so i should recieve an email with an alaert....correct?
I checked SOST and i see no email whatsoever and i am not sure where to begin troubleshooting.
Any ideas?
Mani (I hope i have explained my setup procedure the best i can :s )

Hi,
Yes the SAPconnect was tested and i managed to send myself an email from business workplace without any issues. The CCMS dispatcher is working fine in client 000.
According to your mesage "Also, Do check whehter the autoreaction method is assigned properly - in MTE- properties->method->Autoreaction. "
I checked this but i am not sure what this means but i checked the "Monitoring: properties and Methods" and select methods and looked at Autoreaction method and there is <NO_METHOD> mentioned.
If i double click the MTE class "FilesystemPercentageUsed" and look at the auto reaction method, there is nothing in there. I am not sure where i am checking this or should i be changing it from the SAP-DEFAULT
Any advice?
Mani

Auto-Reaction Method - External Operating System Command

Hello ,
I am trying to run a script (test.cmd) on a monitored java system out of solution manager via ccms auto-reaction method, but without success.
I have created a RFC Connection to the java system in transaction sm59, defined an external operation command in transaction sm69 (/usr/sap/test.cmd) and an auto-reaction method using that command. But when I test the command in transaction sm49 with the RFC connection as target destination, the command is executed on the local CEN system (SolutionManager system) instead of the monitored java system. I have no clue where's the problem???
Thanks for any help (points, points, points)
Mirko

Hi Anand,
can you please send me that doc too pleae.
[email protected]
I really appreciate your help.
Thanks,

Is Pitch Shifter II the same thing as Auto Tune?

I'm looking for a plug-in on Logic Express 7 that is similar to the vocal effect you always catch T-Pain using. I believe it is called Auto Tune. I just wanted to know if this is available in LE7. Thanks.

RyConn M.D. wrote:
I'm looking for a plug-in on Logic Express 7 that is similar to the vocal effect you always catch T-Pain using. I believe it is called Auto Tune. I just wanted to know if this is available in LE7. Thanks.
No. it is not the same. to get those fast pitch rises and falls, you either need auto tune, or a really good Vocoder.
Try using a Vocoder instead. This will be closer to that sound. BTW I work in syndicated radio, and it is the single most overused effect right now, so IMHO, try something else. We're starting to get listener complaints about having so many songs with it on our chart. Seriously...
Cheers

Auto Tune - customized feature (preset) request

The Auto Tune feature usually works quite good and is a real time saving feature. But on some sets of images the effect is too storng (for my taste). If we can have a 'preset' or ability to customize the strenth or effectiveness of the Atuo Tune (i.e. simlar to the FADE SHARPEN in Photoshop after applying the SHARPEN filter), it will be very helpful. This will be very helful especially when we are doing some batch develop with Auto Tune.

A manual auto-tone, that is...

How to change Auto-reaction method automatically?

Hi all,
I want change the Auto-reaction method for few systems in the landscape,How to change the method automatically for all the system with out doing Manually in eash of the system.
Regards,
Neni

Hello
The below URL might be useful to you.
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/201c3148-faef-2d10-ac80-e0a8bc7503a1?quicklink=index&overridelayout=true
Thanks & regards
bala

Load chain auto reaction method

Hi All,
In Bw 3.5 load chain is configured , if load fails an automatic mail is triggered with log message, now i want to change the mail id of the sender .
I had checked in RZ20 BW monitor->process chain and selected the failed one and checked the properties and auto reaction method nothing is configured there.
Where i have to check to change the mail-id of the sender.
Please suggest...
Thanks,
Subhash.G

Dear subhash gadde ,
if u want to maintain the mail-id of the sender right click on the process click the maintain message...then give the variant name and then in the next screen go to maintain recipient list. in that chage the mail and create new one ..as u wish...
Regards,
venu

Parameters for Auto reaction method

Hi All,
I have done BPM for monitoring a batch job and a service desk message is generating every time the job is cancelled, by using an auto reaction method.
As the ticket is generating now, I want the job details also to come in the ticket. Like name of the job, variant, abap program etc...
Can anyone suggest how can I do this.
am using serv_desk_mess_on_alert auto reaction method, if any parameter we can include in this method so that the job which is cancelled, we will get the details of that along with the SD ticket.
Thanks
Tripti

its not possible...

Local auto reaction method no longer linked to MTE

Strange one.... all my local autoreaction methods have disappeared from from my MTE properties in RZ20. The methods still exist in RZ21 and the 'where used' reports that it is still inked to that MTE. Have checked that the mehtod is released for variant * (which is the acitve variant).
Any ideas would be helpful as the only option is to link the methods again manually.....which is mind numbing task. Anyone got a way of linking an autoreaction method (local) to multiple MTE's?
Thanks in advance,
Marcus

Dear Team,
As I have understood, you want to be informed each time a satellite system is not up and running ?
Option 01
========
1. Install the CCSMPING agent in SOLMAN
2. Create your satellites systems through RZ21 - Technical Infrastructure - Availability Monitoring - Configure CCMSPING ...
 Create all satelittes systems ...
3. Then, from SOLMAN_WORCENTER, in SYSTEM Monitoring, you have the status of each satellites systems created
 in RZ21 (point 2).
This option will not advised when a satellite system is down. But from one WEB page, you will have the status of all satellites systems.
Option 02
========
1.Install the CCSMPING agent in SOLMAN
2. Create your satellites systems through RZ21 - Technical Infrastructure - Availability Monitoring - Configure CCMSPING ...
 Create all satellites systems.
3. RZ20 - SAP CCMS Monitor Templates - Double-click on "Availability and Performance Overview"
 Open "Availability" - Then, all satellites systems which have been added under point 2 will appear.
4. Select one satelitte system
5. Open "Availability"
6. Select "ABAP: Checked by CCMSPING.<solman-hostname>.00"
7. When selected, click on "Properties" button.
8. Then, you assign here an auto-reaction method - for example :
 "ccms_send_alert_to_alm_ccms_containerv4".
9. Copy this method to Zccms_send_alert_to_alm_ccms_containerv4.
10. In this method, add you email address.
11. Then, check that job "SAP_CCMS_MONI_BATCH_DP is running. This job collects data in the CCCMS (RZ20).
12. Then, the alert will be automatically sends to your email adress.
Hope it helps ?
Best regards
SAPNetWeaverAdmin

CCMS Auto-Reaction Method Disappearing?

Bonjour a tous et a toutes!
Is anyone has their CCMS Auto-Reaction Method Disappearing?
We are in an HA configuration (3 nodes: #1:SCSASCSdb #2: CI +DI #3:CI only)
For some (i.e.: queue blocking) CCMS MTE, we have configured the ZCCMS_Send_Alert_to_ALM_V2 auto-reaction method.
So, with the proper (XI/CCMS) configurations, we get alerted when queues are blocking.
But for some unknown (as least to me) raison, the ZCCMS_Send_Alert_to_ALM_V2 auto-reaction method disappeared when (either we gracefully swith from node #1 to node #2) and-or we crash a node (node #2 or node #3).
Anyone have seen this ?
Thank in advance !

help help !
Anyone have had this error ?

CCMS AUTO REACTION METHOD

hi all,
i hope u all r fine and in the best of ur health.
i have a problem regarding CCMS Auto reaction method , i want to use my own copy of this method
SALO_EMAIL_IN_CASE_OF_ALERT_V2 , but i am recieving a fatal error when ever i try to execute
auto reaction method manualy in RZ21.The reason that i am using this custom copy of this funtion module is that i want to display my own data when ever i recieve the email.
if any body could help me in this regard, thanks in advance.
regards,
Umer Malik
Edited by: Umer Masood Malik on May 19, 2009 1:10 PM

hi Sean / Bhudev,
i have done that but was not working . but later on i find the answer and the solution.
actualy i am working in 100 client and data supplier program was running though in 100 cleint but
the select statement used in was reffering the 100 client tables so thats why when i used the select
cleint specified statement in my report and then tried again , the data collection method was running properly but was not having the data because earlier it was reflection towards the 100 cleint, but now
its pointing to the 000 cleint so its running....
any way thankssss alott for such help...
regards,
umer

Auto reaction method for transaction SMQ1

Hello
I'm monitoring queues RFC through RZ20, and I'd like to know wich auto-reaction method can I use to unblock the qRFC in transaction SMQ1 or this auto-reaction method don't exist?
Regards

Hi,
Error resolved.
I created a variant for program "RSQOWKEX" with the following attributes.
Queue Name - R3A*
Queue Destination - xxxCLNTxxx
No records later than - 00:05:00
No Running Queues box unchecked.
It has worked for me. Surprisingly, this issue only came up in DEV system. In Quality system, no such issue was there.
Thanks a Regards
Varun Taneja
You can use the above code and see if it helps.
Thanks
SM

Auto-recation method not changed/saved

Hi,
Auto-recation method not changed/saved
In R3 4.6C DEV system, RZ20 MTE = (Filesystem percentageUsed) click on properity and click on Method TAB
in Auto-recation method already setup "Z_NSM_CCMS_OnAlert_Email_V2"
I want to change or replace with CCMS_OnAlert_Eamil after save I got Entry has been saved
but still show samething "Z_NSM_CCMS_OnAlert_Email_V2" is anyone tell me why is like that ???
Thanks in Advanced

I have also reviewed this thread and tried these solutions:
https://discussions.apple.com/thread/5497463

CCMS Auto Reaction Methods in XI AlertFrameWork

Team,
I have setup my XI box to report all CCMS errors to the ALM framework. The scot tcode has been also setup to receive email.
With MBA (Message Base Alert), such as mapping error, receiver not found, etc, I have access to a list of "containers variable" to report detail about the error.
How can I do the same with all errors I get in CCMS ? The errors get replicated to my ALM framework (and thus can be seen in the AlertInbox), but I have no handle on variables container ...
Thank in advance !
A+

Hi Jose,
yes i have tried to changed to P and to whatever you can imagine but no success, could it be because im trying to do this on IDES?
a bit summarizing of what have I done till now.
I have created in client 000 a shared folder called CCMS_ALERTS, I have configured in RZ20 in menu SAP CCMS Monitor Templates --> Syslog --> Security in this way
Everything has been done in client 000
In General Tab i have:
Message Class: RT
Message Number: 079
Severity of alerts to be triggered: 255
Maximum numbers of alerts kept: 10
Which alerts should be kept: ALL
In Log Attribute Tab i have:
Maximum alerts
Always
As many as possible
In Filter Tab I have:
System log message is selected (ticked)
the i have filter
from ID - US1 to ID US1 at Red (ticked) with severity 255
In the method tab i have:
My Own method that i have created and here it is:
Method (rz21)
Execution Tab:
as Functional module - SALO_EMAIL_IN_CASE_OF_ALERT
on any server
Table fo several MTEs
Control Tab:
Periodically in dialog process (short running program)
Parameter Tab:
SENDER: my user (existing in any of the clients with administrator rights)
RECIPIENT: CCMS_ALERTS
RECIPIENT-TYPEID
Release Tab:
Auto-Reaction Method
Please advice what have I done wrongly
Vladi,

Automatic SMS/Mail notification for local auto-reaction method

Hello!
We would like to be informed via SMS/Mail about the Availability of satellite system.
When we assign a Local auto-reaction method for this MTE (Availability_SysPercent_ABAP) we receive the SMS/Mail notification only in case we manually start the auto reaction method from RZ20.
When we try to assign the central auto reaction method from RZ20 we get the following error:
Assignment for local system only works with nodes from agent segments
What is the procedure for the automatic SMS/Mail notification in case of local auto-reaction method?
Thank you very much!

Dear Team,
As I have understood, you want to be informed each time a satellite system is not up and running ?
Option 01
========
1. Install the CCSMPING agent in SOLMAN
2. Create your satellites systems through RZ21 - Technical Infrastructure - Availability Monitoring - Configure CCMSPING ...
 Create all satelittes systems ...
3. Then, from SOLMAN_WORCENTER, in SYSTEM Monitoring, you have the status of each satellites systems created
 in RZ21 (point 2).
This option will not advised when a satellite system is down. But from one WEB page, you will have the status of all satellites systems.
Option 02
========
1.Install the CCSMPING agent in SOLMAN
2. Create your satellites systems through RZ21 - Technical Infrastructure - Availability Monitoring - Configure CCMSPING ...
 Create all satellites systems.
3. RZ20 - SAP CCMS Monitor Templates - Double-click on "Availability and Performance Overview"
 Open "Availability" - Then, all satellites systems which have been added under point 2 will appear.
4. Select one satelitte system
5. Open "Availability"
6. Select "ABAP: Checked by CCMSPING.<solman-hostname>.00"
7. When selected, click on "Properties" button.
8. Then, you assign here an auto-reaction method - for example :
 "ccms_send_alert_to_alm_ccms_containerv4".
9. Copy this method to Zccms_send_alert_to_alm_ccms_containerv4.
10. In this method, add you email address.
11. Then, check that job "SAP_CCMS_MONI_BATCH_DP is running. This job collects data in the CCCMS (RZ20).
12. Then, the alert will be automatically sends to your email adress.
Hope it helps ?
Best regards
SAPNetWeaverAdmin

Auto-tune method

Similar Messages

Maybe you are looking for