Autonomous 1130 AP

Hello all. I"m having trouble converting a 1130 series AP to autonomous mode. I continue to receive the following error when attempting to use Tftpd32 to transfer the ios file: "no such file or directory found". I am currently using the "mode" button method, but I receive the same error when attempting manually as well. I receive this error from Tftpd32: "File <c1130-k9w7-tar.default>: error2 in system call CreateFile The system cannot find the file specified."
Troubleshooting Steps Taken:
1. Verified basic IP connectivity.
2. Disabled firewall.
3. Attempted to use another TFTP application (same error).
4. Set NTFS permissions on file and TFTP directory to allow everyone full-access.
5. Restarted PC.
6. Verified correct syntax on ios file (c1130-k9w7-tar.default).
7. Moved file to multiple directories.
8. Attempted to use another ios file.
9. Confirmed hidden and system files are visible.
Thanks for your time.

That error is usually when the TFTP is using the wrong folder/directory than where the file is actually stored. Also make sure you enable file extension on windows explorer because there might be a hidden extension your now seeing.
-Scott

Similar Messages

Is Guest Access via web auth available on Standalone 1130AP?

Hi,
I have seen that using LWAPP and a WLC, Guest WLans can be authenticated via a web page.
Is this possible on an Autonomous 1130 AP ?
Or is that only a functionality of the Controller ?
Thanks

As the other user said, this web authorization isn't native to the access point. It is a web authorization portal that is on the WLC.
With that said, any web authorization portal on your network could be used. I'm not sure what your budget is, but if you are looking to do this on a handful of devices, you might go with something like NoCat (nocat.net). I haven't actually used it but I think it is just an entry level (free?) portal.
I'm sure there are many of product out there, and cisco probably has thier fair share...
Note: in this case, it would most likely be used to authorize anyone to get connected to the LAN (or Internet), it probably wouldn't be used to authorize the actual Wireless Connection, just authorize the ability to get off the VLAN (like to the Internet)

Steps to convert access point from LightWeight mode to Autonomous mode

I need steps to convert the following access point from Lightweight mode to Autonomous mode
AIR-AP1242AG-E-K9
Regards,
Majid

Hi Majid,
The method is just hidden a little further down the doc that Scott linked (+5 points Scott :)
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Hope this helps!
Rob

Test bed : WLC makes slow WLAN speed vs. Autonomous

Hi experts,
User complint very slow download speed (~140kbps) compare to wire around ~50mbps. Those are too different.
So I move out from the production, then did my own test.
I tested on seperated environment, seperated AP(1130)/switch/ WLC(7.0)/PC client with Windows file sharing. Then compare againt STANDALONE AP. All are flat configure without any Auth etc.
Result are, standalone AP is winner = 5MB/sec while WLC based is only 1MB/sec. Then I also try to do LOCAL SWITCHING (H REAP) to diable tunneling that could make some delay. Result is the same, no improvement.
I also find out for cisco support forum. Much many discussions ask us to disable feature such Client exclude, MFP, Aironet IE and tune for a/b/g supported.
What else to tune or aware of ?
Please do me a suggestion. Thank you.
Nipat.p

David,
Do you mean Static&Dynamic CH? I used default WLC's setting (Dynamic, DCA)?
Anyway, my testbed is using only 1 AP in 2 scenarios WLC-based vs. Autonomous at the same location.
I also asked from the others end user who is using WLC. Windows file share speed is also around 1-2.4MB/sec. So poor!!!
Then, What else for WLC parameter should I take care of? I got a slot to re-test by tomorow.

Error when migrating AP 2600 from Autonomous to Lightweight

Hello,
I am trying to migrating AP 2600 series that came with autonomous image 15.2 to lightweight using the Cisco Prime Infrastructure built-in migration template.
The AP successfully downloads the image from an external TFTP server but fails at updating the environment variables.
The logs show that the AP should download a text file from Cisco Prime but fails to do so:
START: Detailed logging started at -> 01.22.2014_14.01.52
INFO: TELNET to device 10.32.148.225 done.
INFO: Privilege level is equal to 15.
INFO: Setting vty line completed.
INFO: Dumped Environmental variables.
INFO: AP is supported for Upgrade process
INFO: IOS version is greater than or equal to 12.3(7)JA.
INFO: AP has MIC installed already.
INFO: Station role is root.
INFO: Station role is root.
INFO: DNS and Domain name configured.
INFO: Mac address of device is 88:5a:92:17:2b:09
INFO: Completed Dot11Radio0 shutting.
INFO: Device set up done and time configured on device.
INFO: Run-config dumped.
INFO: AP is DHCP configured.
INFO: Hostname gbknwa2225sr
INFO: Dumped Environmental variables.
INFO: Starts loading recovery image, takes time based on link speed.
INFO: Image Loading done.
INFO: Copying updated Env. variable file to WCS local tftp server 10.70.165.165
INFO: Copying the Env. variable file from tftp server to device.
Copying the Env vars to device failed.
ERROR: Device Response ::
copy tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt flash:/env_vars
Destination filename [env_vars]?
%Warning:There is a file already existing with this name
Do you want to over write? [confirm]
Accessing tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt...
%Error opening tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt (Timed out)
gbknwa2225sr#
gbknwa2225sr#_tune_
gbknwa2225sr#
INFO: Un-shut radio 1 done.
END: Migration Process Failure: Copying Env_Vars to device failed.
What can I do to solve that ?
Many thanks for your help,
David

Hi David,
I think 2600 AP not supported on Prime Infra for autonomous to Ligtweight migration.
PI 1.2, 1.3, 1.4 , 2.0
Only these APs are supported: Autonomous to Lightweight Migration Support
Cisco Aironet 1130 Access Point
Cisco Aironet 1200 Access Point
Cisco Aironet 1240 Access Point
Cisco Aironet 1310 Bridge
Cisco Aironet 1410 Bridge
Check this link:
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.4/configuration/guide/ctrlcfg.html
Hope it helps.
Regards
Dont forget to rate helpful posts

Converting LAP back to autonomous failed

I've a 1130 AP which doesn't boot it's LWAPP image from flash. So I tried to convert it back (with tftp server and so on) but after the message that it's using the "reset IP" it tries again to start the (corrupt?) image.
Is there a way to stop this boot cycles and to check boot parameter? Or any other ideas?

Hi Guys,
Today, I have converted the Cisco LWAP (1140) to Autonomous AP successfully.
Follow the below steps:
1. Download your 1142 image from Cisco --- I chose c1140-k9w7-tar.124-21a.JY.tar (Autonomous IOS Image for LWAP 1142)
2. Copy your 1142 image to your TFTP folder and start your TFTP server
3. Hook up your console cable and open up PuTTY
4. Plug in your 1142 into your POE/non-PoE (use Power Chord) switch.
5. Create one DHCP Pool in 10.0.0.0/24 network and let the LWAP and Laptop takes the IP from that DHCP Pool.
6. When it boots and your DHCP server gives it an IP address, you'll get a prompt (*your AP needs to get to your TFTP server)
Use PuTTY and enter in the commands in bold and modify the address of your TFTP server and image accordingly.
APd0d0.fdae.aea4> enable
Password: Cisco
APd0d0.fdae.aea4#debug lwapp client no-rel    ###### Very Important command
LWAPP ignore internal reload debugging is on
APd0d0.fdae.aea4#debug capwap console cli   ######## After giving the above one, this particular command will activate.
CAPWAP console CLI allow/disallow debugging is on
APd0d0.fdae.aea4# archive download-sw /overwrite /force-reload tftp://10.0.0.10/c1140-k9w7-tar.124-21a.JY.tar    ######## After giving the above command "debug capwap console cli" then the "ARCHIVE" command will activate
It starts upgrading the new IOS to the LWAP. After installing the IOS, reboot twice the AP and you can normally see the prompt “ap>”
Regards,
Praveen Neti.

Upgrade 1120G from an autonomous to a lightweight accesspoint

Hi!
I have a network consisting of 22 autonomous Aironet 1120G accesspoints. Is it possible to upgarde these to lightweight accesspoints for using with a Cisco WLAN Controller?

Hi Zach,
These AP's can be converted to LWAPP. We did this exact conversion last summer on about 30 1121G's with the LWAPP upgrade tool. Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
Software release 4.0.155.0 New Features
LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
LWAPP Upgrade Tool Troubleshoot Tips
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
System Requirements
You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
**All 1100 series access points containing MP21G (802.11g) radios
All 1130, 1230, and 1240 series access points
All modular 1200 series access points running Cisco IOS software and containing these supported radios:
802.11g: MP21G, MP31G
802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
All 1300 series access points in access point mode
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
Cisco Aironet 1240AG Series access points
Cisco Aironet 1230AG Series access points
Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
Cisco Aironet 1130AG Series access points
**Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
Cisco Aironet Access Point Support for Lightweight Access Point Protocol
http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
Hope this helps!
Rob

Conversion of an AIR-AP1120B from autonomous to LAP

Does anyone know if it's possible to convert the AIR-AP1120B from autonomous to LAP?

Hi Federico,
Sadly, the 1120 with "B" Radio is not supported :(
Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
Software release 4.0.155.0 New Features
LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
LWAPP Upgrade Tool Troubleshoot Tips
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
System Requirements
You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
**All 1100 series access points containing MP21G (802.11g) radios
All 1130, 1230, and 1240 series access points
All modular 1200 series access points running Cisco IOS software and containing these supported radios:
802.11g: MP21G, MP31G
802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
All 1300 series access points in access point mode
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
Cisco Aironet 1240AG Series access points
Cisco Aironet 1230AG Series access points
Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
Cisco Aironet 1130AG Series access points
**Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
Cisco Aironet Access Point Support for Lightweight Access Point Protocol
http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
Hope this helps!
Rob

Convertion from Lightweight to Autonomous access points

Is it possible to convert AIR-LAP1121G-E-K9 Lightweight access point to autonomous access point.

Hi tm,
You can convert AIR-LAP1121G-K-E9 to autonamus access point,pls do follow the procedur
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4
Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5
Disconnect power from the access point.
Step 6
Press and hold MODE while you reconnect power to the access point.
Step 7
Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8
Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9
After the access point reboots, reconfigure it using the GUI or the CLI.
Thankx&Regds
Saji k.s

1130 not connecting to controller after setting to HREAP

I had an 1130 AP connected to my 4402 controller running 4.2.207. I went to set the AP to HREAP and after I applied the HREAP setting, the AP rebooted and will no longer connect to the controller.
This is the error message I am getting on the controller.
WARNING: invalid slot ID (255) passed to REAP -Traceback=
0x4F026C 0x4F0394 0x498B24 0x491DC4 0x4AAF90 0x48DAC4 0x48E35C 0x197630o REAP -Traceback=
The AP part number is AIR-LAP1131AG-A-K9.
This AP was up and running with no problem until I tried to change it to HREAP.
Any suggestions on how I can recover this AP?
Seth

I had reloaded the AP last night using c1130-k9w7-tar.124-10b.JDA3.tar renamed to C1130-k9w7-tar.default. After the AP came up in Autonomous mode I then converted back to LWAPP using c1130-rcvk9w8-tar.124-21a.JA2.tar. Once the AP joined the controller and got the image it then rebooted and came up with the same error.
So after reading your response I deced to rename c1130-rcvk9w8-tar.124-21a.JA2.tar to c1130-k9w7-tar.default and let the AP load this image. After downloading the image the AP then joined the controller, got its image, then reloaded and succesfully joined.
Thank you for the help.
Seth

1130 Radio Mounting Best practice

Hi Everyone.
In discussions with cisco and other users, we are confused on mounting and radio coverage practices.
should we be mounting the radio vertically with the ethernet to the side or Horizontal to the floor (drop ceiling).
According to others, if the AP is mounted vertically (wall mount) and the ethernet entering from the bottom, the radio plane is north and south (coverage would be up and down).
Anyone have more clear info on this?
Does anyone have

Hi Brad,
Thanks for your reply. I do agree with you.
I have a Cisco certified company who designs and installs wireless who are telling some of our Customers otherwise. They are stating the AP's should be hung vertically (wall mount) with the ethernet entering to the left side due to the internal OmniDirectional Radio.
I have read nothing in Cisco Doc's to make this statement true.
I have been told by Cisco that due to Location tracking algorithms on LWAPP configured 1130's that the Horizontal mount is official. Notice the "LWAPP" !!!! and does this still hold true for Autonomous 1130AP's?

Possible to convert autonomous AP to LWAPP via CLI?

Hi,
Probably a silly question but was wondering why it is not possible to convert an autonomous AP to LWAPP by using CLI commands?
For example we have over 300 access points to convert and thought about using Linux to automate the task but seems there is only a windows conversion utility.
Cheers,
- Trevor

Hi Trevor,
You can convert AP to LWAP using CLI but this is entirely dependent on the model of AP you're dealing with. 1230, for example, requires the conversion tool. 1130, 1240 and 1250 can be converted using CLI. Here it is ...
Requirements:
â¢ Image file (The recovery file has the prefix ârcvâ in the image name, such as c1200-rcvk9w7-tar.122-15.JA.tar);
â¢ AP is connected to the Wireless LAN Controller; and
â¢ AP can ping the TFTP server where the image is located.
Procedure
1. Copy the recovery file to the AP using the following command:
archive tar /x tftp:/// flash:
2. Let the AP boot on this image:
boot system flash://.bin
3. Reboot the AP.
OPTIONAL
â¢ DO NOT ALLOW THE AP TO JOIN THE WIRELESS LAN CONTROLLER IN ORDER TO USE THE OPTIONAL COMMANDS BELOW.
â¢ IF POSSIBLE, type the following commands:
ï¾ clear lwapp private-config (This will bring the AP to factory default.);
ï¾ clear lwapp ap ip address
ï¾ clear lwapp ap hostname
ï¾ clear lwapp ap controller ip address
4. Let the AP connect to the Wireless LAN controller.
OPTIONAL
If an AP refuses to join the Wireless LAN Controller, type the following command from the AP:
lwapp ap controller ip address

Cisco aironet 1130 and Intermec CV30

Hi to all,
I've a little problem with three Cisco 1130 AP. Anticipately i tell you that i'm not a guru of cisco wireless, but my implementation is very simple. I need a roaming for the 3 AP. I only have Ap, so i configure one as Master Ap and the others like repeater with cisco aironet extension configured. All 3 on the same channel and only the Master one broadcast SSID. Wep security implemented. My Cv30 terminals randomly loose the signal also if they're near an AP. They use windows mobile but i think is only a wrong config problem. I need help. Thank you very much.
Alex

The device is using the LWAPP image.. please upgade the same to autonomous image and convert the same..
Please use the below doc that i hv written and this will helpu!!
https://supportforums.cisco.com/docs/DOC-14960
Please dont forget to rate the usefull posts!!
Regards
Surendra

Cisco Aironet 1200 LAP Issues - LAP to Autonomous Mode

Greetings! After purchasing 4 of the Cisco Aironet 1200 G Series WAPs, I'm now running into a slight issue with them.
I received these last week with the understanding that if I didn't have the Cisco controller device, I could convert them from being the Lightweight Access Point, back to Autonomous mode with an IOS.
With this, I checked the documentation that came with the device and found the "Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode" or http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&needs_authentication=yes&CommCmd=MB%3Fcmd%3Dadd_discussion%26mode%3Dshow%26needs_authentication%3Dyes%26location%3D.ee7c7c3.
From there, I followed the instructions listed under Converting a Lightweight Access Point Back to Autonomous Mode. Before the rename of the file, I checked the device and found AIR-LAP1242G-A-K9 for the Model No.
One of the Cisco Certified admins here was able to obtain the latest build for the IOS for the device or c1240-k9w7-tar.123-8.JEB1.tar. Per the instructions, I renamed the file to coincide with the model of the device.
I followed the instructions from there, and it looked as if everything was going well. However, after the upgrade, I'm running into an issue with the following:
File "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1" uncompressed and installed, entry point: 0x3000
executing...
At this point, the device just locks up. All lights are lit green on the device. According do the documentation, it should reboot and from there, I should be able to access the web interface by IP.
I've tried to perform the upgrade again using the same IOS build, but the same thing happens with the lock up.
At this point, I'm assuming the issue is with the build of the IOS that I have and I may have to look at getting an older build. However, before doing so, I thought I would post something here to see if anyone had an idea.
I may have needed to refine my searching of the forums, but wasn't able to find anything in relation to my issue. If there is something out there, I do apologize for the post and will happily refer to any current information.
If you need any further information in relation to this, please let me know. Any assistance is greatly appreciated. Thank you!

Hi Jeffrey,
Reverting the Access Point Back to Autonomous Mode
Have a look at Step 3
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

Upgrade 1121 autonomous to LWAPP

I have some access-points AIR-AP-1121G-TO-K9 and it would like to use them with a WLAN Controller. Is possible to change IOS for the software LWAPP to use with the WLAN Controller?
I know that that is possible in another models of access-points, but I don't know if the 1121 support that upgrade.
Regards.

Hi Andre,
Just to add a note to the good tips from Ankur. These AP's can be converted to LWAPP. We did this exact conversion last summer on about 30 1121G's with the **LWAPP upgrade tool**.
Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
Software release 4.0.155.0 New Features
LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
LWAPP Upgrade Tool Troubleshoot Tips
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
System Requirements
You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
**All 1100 series access points containing MP21G (802.11g) radios
All 1130, 1230, and 1240 series access points
All modular 1200 series access points running Cisco IOS software and containing these supported radios:
802.11g: MP21G, MP31G
802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
All 1300 series access points in access point mode
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
Cisco Aironet 1240AG Series access points
Cisco Aironet 1230AG Series access points
Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
Cisco Aironet 1130AG Series access points
**Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
Cisco Aironet Access Point Support for Lightweight Access Point Protocol
http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
Hope this helps!
Rob

Autonomous 1130 AP

Similar Messages

Maybe you are looking for