Average Dialog Response Time.

Hello friends.........
What is the table or function module that stores the data of Average Dialog Response Time (transaction ST03)? After executing ST03, when a particular date is selected, i need the table or function module that stores the value corresponding to Dialog and Time.
Thanks & Regards,
Ajay.

check ST05? i dont have idea on St03.
or STAT .
Regards
Prabhu

Similar Messages

  • High Dialog response time

    Hi,
    We have a solman 4.0 system. The average dialog response time of the system is very high. What can be done to bring down this response time??
    Thanks in Advance
    Amit.

    Hi Amit,
    Please check out the breakdown of dialog response time in Workload Monitor. Also, use the Time Profile to check if this high response time is at specific timings.
    regards, Shantanu

  • CCMSPING not collecting "Dialog Response Time"

    In Solution Manager 4.0, we have configured the CCMSPING agent to monitor a number of systems.  For only two of those systems, CCMSPING is not collecting "Dialog Response Time" (Availability_DiaRespTime) and "Standardized Response Time" (Availability_StdRespTime) data.  All other MTE's for those two servers are being successfully collected.  Looking at CPH, for at least one of those systems, the data was collected for a couple of weeks and then stopped.  For the other system, that data has never been collected.  The two systems with problems are the only two ECC 6.0 systems in the landscape.  In the RZ20 monitor, all that it says is that the "Value is obsolete".  I have deactivated and reactivate CCMSPING one of the systems without any change.
    Has anyone seen anything like this?  Is there any way that I can find out what errors are occurring?

    I have already a ccmsping agent registered on my central system but it seams to be not correctly registered.
    I registered correctly the agent with the '-push' option and it seams to work properly now.
    Thanks for your response
    Regards,
    Emmanuel Coindre.
    [www.emmanuelcoindre.fr|http://www.emmanuelcoindre.fr]

  • Dialog Response Time is Missing in ST03N

    Hi,
    In one ofour SAP system the dialog response time data is missing in ST03 however other Task type such as RFC,SPOOL,AUTOABAP,AUTOCCMS,BACKGROUND etc are visible.
    OS COllector job is running fine and collecting all data except DIALOG
    Step for issue reproduction :
    ST03n > Expert Mode > instance > under workload overview > Task Typne Name ( Here it should show the data/response time for Background,spool,update etc).
    Kindly help me to know why it is missing. Screenshot for the same is attached here.
    Regards,
    SURYA.

    Hello Surya
    here screenshots from my test:
    ST03 for my instance before I have executed something on it, no dialog task type:
    here I have connected to the instance through SM51, still no dialog task type:
    and here I have connected directly through SAP Logon to this instance, now my actions on the instance are displayed as dialog task type:
    If your users connect through RFC to the instance, then all their actions are RFC task type actions. As soon as a user logons directly to the instance, dialog task type will appear in ST03.
    regards,
    Alwina

  • Dialog response time comaprison between cities

    Is there any way where we can compare dialog response time  in different cities for the same transaction?
    As we are facing issues with response time in 2 different cities and response time in 1 city is lesser comared to other city while fetching the same data.
    System is an ABAP ECC 6.0 R/3 system.
    We checked that GUI time is also different in both cities.

    Hi,
    Check the network times from each city with the SAP utility niping.
    Check also if people from the different cities are connected to the same application servers.
    Regards,
    Olivier

  • Dialog response time exceeds threshold (SOLMAN Alert)

    Dear All,
    I found an alert in Solution Manager,
    2.023 msec > 2.000 msec Dialog response time exceeds threshold (56 dialog steps)
    What does this alert means?
    Are SAP system still in a good performance?
    And what kind of action i have to do to clear this alert..?
    thanks and regards
    Rio(nubie)

    Hi
    What does this alert means?
    see answer Mapp Tyrone above
    Are SAP system still in a good performance?
    SAP performance is not determined only by response time. you have to look globally: your free memory, your ABAP dumps, your swap, your database statistics etc.
    And what kind of action i have to do to clear this alert..?
    No need to clear it. All you have to do is tune your SAP system to increase your current performance, and one indicator of that is the better response time.
    hope it help you.
    rgds,
    Alfonsus Guritno.

  • Average HTTP response time going up week by week as said by SAP

    Hello All,
    I was looking into our SRM earlywatch report,SRM is on windows SQL server 2005 with Windows 2003 server
    In the performance indicators,there is an interseting trend though nothing is in yellow or red
    The values of following parameters : average response time in HTTP task, the maximum no of HTTP steps per hour and the average DB request time in HTTP task  are going up
    I understand that as the no of HTTP steps are increasing,the response time is becoming more which is quite obvious.
    But how to balance this load out so that the average response time comes down?
    what steps should be taken so that I can get this response time to come down though the load on the server is going up
    Rohit

    Hi Rohit,
    Is you system in High Avalibity setup? If yes, then try to load the balance on Node A and Node B. If this is already done or if your system is not in high availability then plan and install a Additional application server (Dialog instance) for load sharing.
    Regards,
    Sharath

  • CCMS Monitoring for Average HTTP response time

    Hi guys ,
    Is it possible to monitor Av. response time for HTTP(this is based on ST03) using CCMS ?
    Thanks in advance
    George

    hi
    As per my understanding you tried to view the responsetime comp as same like in sto3 by ccms, the way as below, RZ20-> SAP CCMS montior templates- >Entiresystem-><sid>->application server -><server>R3 services ->  DIalog you can get all the response time as same in the ST03.
    else in otherway if you looking for monitoring Java and webdynpro, you can do this by GRMG.chk this for to knw http://help.sap.com/saphelp_nwpi71/helpdata/en/45/4ee37fea5917eae10000000a155369/content.htm|http://help.sap.com/saphelp_nwpi71/helpdata/en/45/4ee37fea5917eae10000000a155369/content.htm]
    for configuration,[GRMG-config guide|http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/106a4d88-2a36-2c10-549b-dc549d00b8b9?quicklink=index&overridelayout=true]
    chk and update
    jansi

  • Table name for dialog response time without GUI in ST03?

    In SWNC_COLLECTOR_GET_AGGREGATES, cnt00x (x =1,2,3... 9) gives me the proportion of transaction steps with a response time between 0s and the upper  limit of the individual response time categories (includes GUI time), broken down by task type. But where is the data without GUI time store? any ideas?

    Hello Surya
    here screenshots from my test:
    ST03 for my instance before I have executed something on it, no dialog task type:
    here I have connected to the instance through SM51, still no dialog task type:
    and here I have connected directly through SAP Logon to this instance, now my actions on the instance are displayed as dialog task type:
    If your users connect through RFC to the instance, then all their actions are RFC task type actions. As soon as a user logons directly to the instance, dialog task type will appear in ST03.
    regards,
    Alwina

  • Average support response time with free support plan

    Some time ago I noticed that I have 3 Adobe ID's.
    2 of them are correct
    2 of them have products registered to them
    1 that has a product registered to it is erroneous: has the wrong country in its registration details
    I contacted support and was assisted promptly and accurately. I needed to provide a few more details that I had to take a moment to collect. The support agent opened up a support case where I could later place the missing information.
    I informed the support agent that I would be away on holiday for a week. And immediately after I added the information that'd come in in the meantime.
    This was 1st of may. All has been silent since then.
    I tried to open up a chat to ask what the average response times are for free support plan subscribers, but I no longer get access to the chat... I guess I was probably just lucky the first time.
    Anybody here know when (on average) I could expect an update to that support case?

    Up to 2 weeks and given the current madness after the CS7/ CC announcment possibly longer.
    Mylenium

  • Average Response Time Different in SLR/EWA (in solman) and ST03 (in satelli

    Hi All,
    We find that the average dialog response time shown in SLR and EWA reports of Solman is much lower (250 ms) whereas the dialog response time shown in ST03 transaction of the system (XI instance) is high 2000 ms.
    Which one is correct and how can I correlate these two values if both are right in their own way.
    regards

    Hello,
    The data source is ST03, therefore unless there is an issue with the collectors, you should assume the ST03 data is correct.
    Pleae run RTCCTOOL on the managed system and ensure ST-PI and ST-A/PI are current.. Also make sure your SAPOSCOL is current.
    There is a possibility that there was an error during preparing the transport to send the data back to Solution Manager, so scan the SDCCN task logs for any errors/warnings on the managed system. You can also check the transport to see what vaues are being returned to Solman's service session. If the have the same value as ST03 at this point, then there is an issue witht eh EWA/SLR provcessing. If the data is not the same here as ST03 then there was an issue with the SDCCN tasks.
    If the data collection is not at issue and the transfering of that data to Solution Manager service session had no errors, then Please follow Jared's recommendation, as this would then be an issue processing the service sessions, and this could be due to outstanding Service Content updates. This can be checked with transaction code AGS_UPDATE.
    Regards,
    Paul

  • High GUI Time - Causing high Response time

    Hi All,
    Average GUI Response time is approx 400 ms in my ECC 6.0 system, OS - HP UX, Database - Oracle 10.2.0.5.
    I expect it should always be approx 200 ms, but as it is high it is contibuting to high overall response time.
    I expect there are normally two ways of high GUI time :
    1)  High network time between Presentation layer( User System) and Application Layer(SAP Server).
    2) High amount of time in Loading User Screen
    For Option 2 I have checked we are using SAP access menu so there should not any problem with loading of User Access Menu.
    Average Response time for session_manager is 2 Secs.
    Please suggest me what all other ways available to improve GUI time,
    Can there be other reasons of high GUI time and how can we make sure that high GUI time is only because of high Network time.
    Please suggest.
    Shivam

    I believe in case you have multiple roundtrips per step, then the client performance comes into play as well. So if you have slow clients this could be an issue too.
    Basically you are already looking in the right place (network connection), but i recommend you also check:
    - roundtrips per step and amount of data sent to the client
    - are all transactions having high gui times, or only a few?
    - how is the situation on the clients?
    - if you have clients working on prod and qas check the values on the qas system too
    Cheers Michael

  • High CPU response times, altough low CPU utilization

    Hi Friends,
    We have a performance problem after we migrate our basis system,
    The current system is :
    Database server : Sun SPARC Enterprise T5240 Server - 2 CPU's with 6 core, 8 thread, 1.2 Ghz
                               32 GB RAM
    and we use another identical configured server as an application server.
    Database is Oracle 10.2.0 and operating system is Solaris 10.
    The problem is average CPU response time is 450 ms, and max. CPU load is %5 percent.
    Pre-migration configuration with old servers, we had CPU response : 150 ms and max CPU load: 50%.
    Has anyone of you, have experinced a similar problem with this new CPU's?
    Thanks in advance

    > I am aware that there might be lots of reasons, but what I  guess is, there should be a parameter wrong with the CPU settings. This SPARC server CPU is a new tech. 6 core 8 thread one, which is expected to work much faster than the old simple dual core CPU.
    Is it?
    ABAP is basically a virtual machine and what is most important: ABAP runs single threaded. This means in consequence that the processing time of a program relies on the single processing power of one core. More cores means more parallelism but the speed of the single statement always relies on the power of one core and how fast it can get the data over the bus and back. So the significant number for speed is basically the Mhz (for ABAP, Java is very different).
    Your old machine may have had a DualCore SPARC 1,2 Ghz and the new machine has one 1,4 Ghz 6core CPU (assuming so).
    > However its response time is very high, although it is never utilized more than %5 percent.
    see above.
    > The problem might be at database settings(Oracle 10.2.0) or at Solaris ? ? ?
    Well - no - I don't think so
    Since ABAP is a single threaded application it can't leverage the CPU power due to the fact, that a parallelism in the program itself does not take place and hence the machine scales not linear with the number of cores. So you may have factually a machine with about 1 dot something CPUs and not 6 as you would expect.
    This is not specific to SPARC CPU design but for all multi-core systems. A single threaded application is only as fast as the CPU speed. ABAP programs tend to be huge so you will also see effects of cache displacement and bus congestions. Less cores and more physical CPUs perform much better than any multicore CPU.
    For Java the world is very different because Java works as one process (in the SAP case jlaunch) which has many many threads that can be executed in parallel on different pipelines on the CPU.
    Unfortunately this is a design problem and there's not much you can do about it.
    Markus

  • Avg iview response time

    At Workload Analysis (Sol man Diagnostics) why I have u201CAvg servlet/webdynpro response timeu201D and u201CAvg iview response timeu201D?
    I mean, the request time of the iview is calculated separated from the request time of the servlet (In case I have an iview with a servlet inside), if so I have to sum both to have the complete time request? Or the KPI u201Cavg iviewu201D is for the iviews that does not have a servlets or a webdynpros inside?
    I am a little confused with these concepts, someone can explain to me or show me some document that explains this?
    Thanks in advance
    Regards,
    Walde Requena

    I don't understand the question.
    Do you want to know how to display dialog response time in ST03? If so, your instructions tell how to bring up that screen. It will show Dialog response time providing there have been Dialog steps executed.
    Or do you want to know which function module you call to get dialog response time data? Use SAPWL_WORKLOAD_GET_STATISTIC to get hourly, daily, etc. data (for a given day and instance) for each task type.
    Tim

  • How to get query response time from ST03 via a script ?

    Hello People,
    I am trying to get average query response time for BW queries with a script (for monitoring/historisation).
    I know that this data can be found manually in ST03n in the "BI workload'.
    However, I don't know how to get this stat from a script.
    My idea is to run a SQL query to get this information, here is the state of my query :
    select count(*) from sapbw.rsddstat_olap
    where calday = 20140401
    and (eventid = 3100 or eventid = 3010)
    and steptp = 'BEX3'
    The problem is that this query is not returning the same number of navigations as the number shown in ST03n.
    Can you help me to set the correct filters to get the same number of navigation as in ST03n ?
    Regards.

    Hi Experts,
    Do you have ideas for this SQL query ?
    Regards.

Maybe you are looking for

  • Sending a smartform output as an attachment in RTF format via E-mail

    Hi all,      I have a scenario in which the output displayed using smartforms is to be sent as a e-mail attachment. Also, the attachment should be a word doc(RTF format). Can you please me with this. Warm Regards, Abhijeet

  • How can I use the Windows 7 high contrast theme with CS6?

    I prefer using a high contrast theme in Windows, as I find it reduces eye strain, unfortunately these themes don't work in InDesign CS6 (i've tested Illustrator, Dreamweaver and PS and they seem to handle the high contrast theme ok, but this forum do

  • DOWN PYMNT TO VENDOR

    Dear Freinds, Pl advise what doc type i shuld select when I make down pymnt to vendor (F-47), so that I get to see the PO number field where I can give PO numb. <u><b>Scenario is that, I want to give PO numb. when I create Down Pymnt Request (DPR)</b

  • How to Remove Google AdSense?

    I have about 50 pages on all of which I've placed Google ads (usually 3 per page). How do i remove the ad source code without going in manually through 50 pages? I've been trying the "Find And Replace" feature, but the problem is that the each ad has

  • Mac book air grey screen padlock

              when i turn on my macbookair I have a grey screen and a padlock w/ password bar. what's going on? what can I do to remedy the situation. thanks.