AX and Netgear DG834G

Hi,
I currently connect to the internet using my aiport card and Netgear DG834G.
Any chance of connecting via AX instead but using the Netgear product to extend my range at home?

It is absolutely not possible to use your Netgear router to wirelessly extend the wireless range of an Airport Express. And no, it won't work the other way around either. The only way you can connect these two devices together is via an ethernet cable - which I suspect is not what you had in mind.

Similar Messages

Airport Extreme and Netgear DG834G v2 very slow

Hi,
I've just bought an iMac 17" dual core and I'm having problems with slow download speeds when connecting to my wireless network: I have an Airport Extreme card and a wireless ADSL Netgear DG834G v2 router. All my machines on this network all have acceptable download speed but when I use my mac, the download speed is very poor. For example, I tried to download a file on my XP machine and got a rate of ~250kb/sec but when I use the mac, I get ~40kb/sec. In general, internet browsing on the mac is very slow.
Things I've tried:
1) Plugged the mac into ethernet and that is working fine so the wireless connection seems to be the problem.
2) Put the XP machine and mac (both working wirelessly) at the same location - the mac is considerably slower than the xp machine.
3) I've downloaded and installed all the latest updates and firmware for the mac but this has made no difference.
Does anyone have any suggestions on what I can try next?
Regards
calumr
iMac 17" dual core Mac OS X (10.4.8)

Got it working - just needed to upgrade firmware of my router.
iMac 17" dual core Mac OS X (10.4.8)

Time Capsule 4 and Netgear DG834G router.

Hi - help required please! . I've replaced by old Time Capsule with a shiny new 4th generation, but cant seem to get it playing with my original Netgear router. I had previously had two wireless networks running - one from the router and one from the time capsule. With the new TC this seems to give all sorts of conflict problems. Rather than trying the bridge mode I thought I would disable the Netgear wireless network and use it just as a modem. I got as far as then creating a new wireless network just on the time capsule, got the magic green light going ... but no Internet access for my Mac! There must be some settings that I need to change, but after two hours on the phone to Netgear they could not work it out.
Does anybody here know how to finalise this set up/
With thanks in advance ..

Does the Time Capsule reside on the same sub-net as the Router. e.g. do the first 3 numbers in the IP address the same 192.168.0.xxx.
Have you told the Time Capsule that the DNS Server is the IP Address of the router?
I would setup the IP Address on the Time Capsule to be static, and disable the DCHP server.
I don't have a Time Capsule but this what I would do.
Router
IP Address 192.168.0.1 (default)
Router Sub Net 255.255.255.0
Router LAN settings
DHCP Server Enabled, Range 192.168.0.20 - 192.168.0.80
Time Capsule
IP Address 192.168.0.2
Subnet 255.255.255.0
DNS 192.168.0.1
DHCP Disabled
Hope you get this going. I have issues with the DG834G and third party Time Capsules, do good luck
Patrick

IChat on 10.4.3 and Netgear DG834G

Since 10.4.3 my iChat stopped working. During starting up the application would simply close down without any error message. On the discussion forum it was suggested to startup from terminal with debug switched on. This produced the following error:
wolf:~ alex$ /Applications/iChat.app/Contents/MacOS/iChat -errorLogLevel 7
205454.103809 Loading hardware rules from hardwarerulesH264-G4.plist
205454.104476 Checking H264 hardware rules
205454.104778 Satisfied rule #4 (30:160x120)
205454.105384 setLocalUserName: [email protected]
205454.142300 ### NEW STATE: to: VC_INIT, from: VC_INVALID
205454.143868 ### NEW STATE: to: VC_IDLE, from: VC_INIT
205454.144271 ++++++++ confStatusMapRemoveAll
205454.144493 ( ) -- mapUserIDToSecurityInfo cleared --
205454.145108 UPnP init passed
205454.145733 NATTraversal created
205454.146234 QT automatic setting = 1
205454.146586 Bandwidth based on QT prefs = 0
205454.153292 BWD: cache: '[192.168.0.6:255.255.255.0]' != '[192.168.0.5:255.255.255.0]'
205454.153907 BWD: Launching thread to determine focus capability based on bandwidth.
205454.207704 QT automatic setting = 1
205454.208263 BWD: Using QuickTime value: 0
205454.208600 BWD bandwidth: 0 kbits up, 0 kbits down.
205454.208802 videoNetworkCapable: 0 -- 0 max participants.
205454.208969 audioNetworkCapable: 0 -- 0 max participants.
205454.209277 vcCapabilities returns: 0x00000007
205454.209831 VCCapAudio
205454.210063 VCCapVideo
205454.210231 VCCapMultiAudio
205454.574552 UPnP Router Info:
- manufacturer [Netgear]
- friendly name [Netgear DG834 Router]
- model name [ADSL Firewall Router]
- model desc [Netgear DG834 Router]
205454.575953 UPnP: Begin TCPProc
Broken pipe
I had to disable UPnP on my router to be able to start iChat. So disabling UPnP solves the startup problem, but I suspect would create problems during Audio and Video connection handshake.
Any suggestions on how to fix this in a better way ?

HI Alexander,
205454.146234 QT automatic setting = 1
205454.146586 Bandwidth based on QT prefs = 0
205454.153292 BWD: cache: '[192.168.0.6:255.255.255.0]' != '[192.168.0.5:255.255.255.0]'
205454.153907 BWD: Launching thread to determine focus capability based on bandwidth.
205454.207704 QT automatic setting = 1
205454.208263 BWD: Using QuickTime value: 0
205454.208600 BWD bandwidth: 0 kbits up, 0 kbits down.
This bit says the Quicktime setting in System Preferences > Quicktime > Streaming tab is not set.
However it is seeing your Netgear so someting is working.
The Broken Pipe message normally means that the app is not seing the support folder properly. Now this could be the App or the Support folders that are at fualt.
You need this FAQ and the Hard way instructions for the support folders and the Upgrade info at the bottom of the FAQ.
Ralph

SBWM and Netgear DG834G fails to connect prope

I have seen the various KB articles on this. My SBWM can see the SSID of the router. I get to the point of getting it to connect and if I specify the IP address for the SBWM I see it as an attached device on the router (I can actually ping the SBWM) however the SBWM itself fails with a communications error.
I note that the router does not see the Name of the SBWM.
Does anyone have any suggestions as to what else I can try. I lift all firewall rules and have UPnP enabled. Still, it does not work.
Thanks

Well, I've answered my own question. I started thinking about the fact that although the router could ping the SBWM receiver, my computer could not. I then checked whether I could ping the router - I couldn't
I then looked at the error code (65) for the ping, and Microsoft were quite clear that it was something to do with Zonealarm. Although I had disabled Zonealarm, it still seems something of it was hanging around. So I uninstalled it.
I rebooted and presto! I could ping the router and the SBWM from my computer - the router now has the firewall logic.
So the problem was that I had not followed the KBase article well enough (it advised disabling everything and then working up from there). My mistake! No to see how this baby works!

Netgear DG834G and Airport Extreme ?

I've done a few searches and I just need this confirmed ...
I've got a Netgear DG834G Wireless Modem router and an Airport Extreme and would like to get them talking to each other - which I thought I did last night ! - so i can have the ADSL connection in one room shared out over wireless to the AE connected to a G4 via one of it's ethernet ports ...
I have read that the Airport Express and a Netgear device is not compatible with Apple's WDS - does that apply to the Extreme as well ?
Is that correct as when I checked the log on the airport it had made a connection with the netgear but I couldn't for the life of me organise a proper network between them !
Any suggestions appreciated...
I've been using the Airport for ages so not a real newbie... BUT... getting them to do what I want is proving an interesting project !
Mitch

Personally I wouldn't go for a USB adaptor as they are pretty ropey at best. You can get Wireless to Ethernet bridges that join an existing wireless network and provide an ethernet connection. They don't require WDS support as they pretend to be a client on the wireless network. Netgear even do one (allthough as you probably guessed I'm not a keen Netgear supporter).
The other possibility is if it is a G4 desktop that has PCI slots a Broadcom based PCI wireless card will be automatically recognised as an Airport Extreme card by OSX and can be picked up cheap on eBay.

Netgear DG834G and HP Photosmart 6520

Hello,
I've just bought HP Printer Photosmart 6520 .
I can marvelously print through USB, but when I try to use Wifi, it doesn't work.
Wifi configuration seems to be good from the printer : an IP is set correctly on my local
network (Netgear DG834G router)
But from any PC , I cannot ping and obviously print on the Wifi IP address of the printer.
Is there any specific setup to do on the router , in order to use printer wirelessly ?

Hi there , Welcome to the HP Community I noticed your posts and wanted to reach out to you! After checking the drivers and downloads webpage to see the available drivers for your Photosmart 6520, there is currently no Windows 10 drives available for your printer. I will include the link below for you to check up on the drivers available.HP Photosmart 6520 e-All-in-One Printer As for your second post, I am unclear of what exactly you are trying to do with the printer setup. Please let me know more detail about what you are looking for. Enjoy your Monday! Say "thanks" for the reply by clicking the thumbs up below!

Netgear DG834G and WPA

I am currently using a Netgear DG834G wireless ADSL router with WEP and a PowerBook G4. I am trying to use WPA instead of WEP but I am having no luck. I switch the router over to WPA-PSK and set a password, I then try and connect to it from the PB using WPA Personal but just get an error message on the PowerBook, 'error trying to connect to network'. Currently I have SSID turned off, the router has the latest software installed as does the PowerBook. Is it possible to use WPA with a Netgear DG834G and a Mac PB?
WEP is working with no problems.
Phil

I encountered this same problem on my Intel Mac when I did the upgrade to 10.4.9. My Netgear router worked fine before the upgrade. I haven't seen anyone with this problem on a G4 before, but there have been lots of reports of problems with Intels. Are you really running 10.4.1 as it says in your footer?
Anyway, here is the only workaround I have found: Go into the router and disable password protection. Mine now works. I'm hoping that Apple will fix the problem, but apparently hasn't happened yet.
Jon

Netgear DG834G and time capsule

I've ordered a Netgear DG834G and a Time Capsule. Since the Netgear has only G capability while the TC has N, I wonder if it will be possible to use the Netgear connected to the TC at its full bandwidth for HD sharing. I've seen similar posts on this board but haven't understood about this specific question. Thanks.
Message was edited by: tago

Yes, this can be accomplished and it is known as a "dual-band" network. You can set it up by either having the Netgear or Time Capsule (TC) directly connected to your modem. As an example, I will assume that you will have the Netgear connected to the modem. In this case, you will connect the TC directly to one of the available LAN ports on the Netgear using an Ethernet cable and connect this cable to the TC's WAN port. The TC will need to be reconfigured as a bridge to allow the Netgear to provide both NAT & DHCP services for both routers' clients.
You will then give each wireless network a unique Network Name/SSID and configure both to operate in different radio modes. In this configuration, "n" clients would connect to the TC and "g" clients would connect to the Netgear.

Netgear DG834G and Airport Express

Hello,
Can anyone help me? I've just upgraded to a Netgear DG834g Wireless ADSL router. This is connected via ethernet to my G5, and my iBook and girlfriends Powerbook connect to it wirelessley.
Setting all this up took minutes. So far so good.
BUT, I cannot get this to talk to my Airport Express.
In the Netgear setup, I have added the AE to the 'Trusted' list (I used the MAC address on the side of the AE unit), but nothing will detect it.
I've tried using Airport Setup utility on both the iBook and the Powerbook but neither device can see it.
The amber light on the AE just flashes. I've even done a factory reset on it, but still no joy.
I've read through some posts on here and I can see that folks have managed to get these two devices talking to each other, but what I want to know is How? Have I missed something obvious?
Please help....
BTW, I'm using OS X 10.4.2 on all machines.
Many thanks

Panic over - the AE needed a hard reset, and re-configuring through Netgear set up, and AE setup utility.
All working fine now.

Hi there, I have just bought an ipad4 but it will not connect to my internet. I have tried every suggestion going to no avail. My netgear DG834g router is fairly old , do you think this is the problem? I am at a loss now and very frustrated!

Hi there, I have just bought my first ipad4 and have spent all weekend trying to connect to the internet. I have tried all Apple suggestions to no avail
. My Netgear DG834g router is a few years old now. Do you think this may be the problem? Do they have compatibility issues after a while? My ipad upgrade is IOs 6. I am at a loss what else to do and needless to say extremely frustrated!
Thanks.

First check that your router has its latest firmware.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Since you are a new iPad user .....
Complete guide to using iOS 6
http://howto.cnet.com/ios-6-complete-guide/
Guide to Built-In Apps on iOS
https://sites.google.com/site/appleclubfhs/support/advice-and-articles/guide-to- built-in-apps-ios
You can download a complete iOS 5 iPad User Guide and iOS 6 iPad User Guide here: http://support.apple.com/manuals/ipad/
Also, Good Instructions http://www.tcgeeks.com/how-to-use-ipad-2/
Apple - iPad - Guided Tours
http://www.apple.com/ipad/videos/
Apple iPad Guided Tours - Watch the videos see all the amazing iPad apps in action. Learn how to use FaceTime, Mail, Safari, Videos, Maps, iBooks, App Store, and more.
http://www.youtube.com/watch?v=YT2bD0-OqBM
http://www.youtube.com/watch?v=ROY4tLyNlsg&feature=relmfu
http://www.youtube.com/watch?v=QSPXXhmwYf4&feature=relmfu
How to - Articles & User Guides & Tutorials
http://www.iphone-mac.com/index.php/Index/howto/id/4/type/select
iPad How-Tos http://ipod.about.com/lr/ipad_how-tos/903396/1/
You can download an iPad User Guide to the iPad from the iTunes store.
 Cheers, Tom

Netgear DG834G setup with Airport Extreme Base

Until yeseterday my home network consisted of an ADLS modem connected by ethernet to an Airport Extreme base, to get additional range I have an additional Airport Extreme Base downstairs ( life before ap express). I also have a USB printer in the 1st base - all was good and life was wonderful.
Then..... the adsl modem/router died. It was recommended that I get the Netgear DG834G as it was easy to setup blah blah blah... Long story short it is set up and I do have internet access wirelessly to part of my house - the range is terrible. I would like to use the two airport base stations I have to get acceptable coverage and also to use my printer via the USB again.
Can anyone please tell me how to make the airport bases talk to the Netgear. BTW ... Base #1 is sitting next to the Netgear box so if it needs to be connected by ethernet it is no problem.
Thanks much Susan

You can connect your AirPort Extreme base station (AEBS) to the Netgear via Ethernet. Configure the AEBS so that the option to distribute IP addresses is disabled.

Airport Express & Netgear DG834G 54Mbps Wireless ADSL Modem Router

Could you offer any advice as to whether an Airport Express could be used as a range extender for an existing Netgear DG834G 54Mbps Wireless ADSL Modem Router setup as I really like the idea of Airtunes and sharing a USB printer. I gather that it is possible to use an Airport Express to extend the range of an Airport Extreme basestation setup but have not been successful in finding any info regarding the Netgear.
Any info gratefully received !
G5 Dual 2.3Ghz Mac OS X (10.4.6)

mac-junkie, Welcome to the discussion area!
No it can not be used as a range extender.
But you can still use it for music and printer support. See KB 302153, AirPort Express: How to join an existing wireless network in client mode.

Netgear DG834G Problem connecting iMAC G5

Hi,
Wondered if anyone could assist me in this.
Netgear Router DG834G / 3 Pcs all set up on Network / added a iMac G5 (Intel/10.4.4) at w/e but with problems - mainly it says it is connected to Netgear but will there is no connection to the internet (when going into Safari).
Stumped by this - I have set TCP/IP address etc ip (192.168.0.5) etc...it is connecting to the Netgear router - but that's as far as it goes.
I have connected via the ethernet cable from the iMac to Netgear DG834G Router - this works fine but knocks off all the other PCs connections. (The connection is still registered (i.e.signal present) but will not log on to any sites etc.
If you can suggest anything it would be much appreciated - I am completely stuck !
Many Thanks in Advance.

Hughxxx, Welcome to the discussion area!
...added a iMac G5 (Intel/10.4.4)...
You do not have an iMac G5. You have an Intel iMac. Those are discussed in the iMac > iMac (Early 2006) > Internet, Networking and your iMac discussion area.
...I have set TCP/IP address etc ip (192.168.0.5)...
Why did you not use DHCP? Try that.
What you are describing is usually a DNS problem. Setting the Network preference to DHCP should solve it. If not see KB 106798, Mac OS: Troubleshooting "A connection failure has occurred", "The specified server could not be found" or Similar Messages.

Airtunes with Airport Express - web with netgear DG834G?

i have a netgear DG834G router which i use to connect to the web (and if you're reading this is it is working . I want my Airport Express to play airtunes, whilst i browse the web. I cannot even get airport Express to join the netgear network (in fact the netgear network doesn't even appear in the airport admin utility list). Any one able to shed some light on what appears to be a simle problem?

Ok, let's double-check your AX's settings ...
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
To set up AirTunes on the AirPort Express Base Station (AX), temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, use the AirPort Admin Utility to check these settings:
AirPort tab
o Base Station Name: <whatever you wish or use the default>
o Wireless Mode: Join an Existing Wireless Network (Wireless Client)
o Wireless Network: <select the existing Netgear wireless network>
Music tab
o Enable AirTunes on this base station (checked)
o Enable AirTunes over the Ethernet port (optional)
o iTunes Speaker Name: <whatever you wish>
o iTunes Speaker Password (optional)
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

AX and Netgear DG834G

Similar Messages

Maybe you are looking for