AX Needing restart often

Right now I have my AX configured to join my AirPort Extreme Base Station's wireless network (not extended, cause for some reason it just doesn't work) so I can have my Mac Pro connect to the internet via ethernet to my AX. It seems quite often when I restart my Mac Pro, the AX looses connection via ethernet and needs to be restarted. Is this a common problem? or a bug? I just want to know if I have a defective product and whether or not it needs to be replaced.

dchao99 wrote:
I am surprised this configuration even works.
Normally, if you set the AX to join a wireless network, the AX is put into client only mode, and the ethernet port is disabled (I've tried several times already). I don't get how you can get ethernet to function out of the AX! Are you sure the Mac Pro is not connected via Airport? Did you disable the Airport on your Mac Pro?
My Mac Pro does not have an AirPort Card. In the AirPort Utility when selecting my AX, I clicked on Manual Setup. In the Wireless Tab there's a pulldown for several Wireless Modes. With 'Join a wireless network' selected. You can select your current wireless network and underneath that is a check box to 'Allow Ethernet clients'. Preferably I would like to have it setup to Extend my current wireless network, but I loose internet when I do.

Similar Messages

How can I avoid the need to OFTEN refresh or recover HP 2000 notebook?

How can I avoid the need to OFTEN refresh or recover HP 2000 notebook? Windows 8.0.

I found your support page by searching E0M18UA#ABA (as opposed to EOM18UA#ABA) which I assume was a simple typo. To answer your original question, the answer is to identify and isolate the cause of the errors and issues you are experiencing. Once you identify each issue, you can find what it takes to get beyond them without having to refresh or recover so frequently.
You can only troubleshoot and identify the issues that are currently happening. If you are getting freezing right now, first take a look at this document specific to the freezing to narrow down the cause: Computer Locks Up or Freezes (Windows 8)
A link to this document is contained in the previous one, but it is worth pointing out that this might be valuable to test for hardware failures: Testing for Hardware Failures (Windows 8)
Another valuable tool when trying to identify the source of the problems, is to perform a clean boot after having one of the issues and trying to recreate it. This shows how to remove startup items. A good strategy is to disable half of the available items first, then restart and try to recreate the issue. If you cannot recreate it then perhaps there is a problematic startup item. If you can recreate it then disable half more, and repeat a few times until you empty the startup items.: How to perform a clean boot in Windows
I hope this helps, and by no means is this a recipe to fix your current issues, but a few strategies to help you better identify the issues.
TwoPointOh
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

HT3180 My wireless router needed restart. And, no Apple TV signal. How do I reset the Apple TV box.

My wireless router needed restart. And, no Apple TV signal. How do I reset the Apple TV box? no lite. nothing

The remote app requires both to be on the same network and home sharing to be enabled, you will need the physical remote to set this up. You can purchase a replacement through Apple.

I have a mac OS X and when I close it and reopen my screen opens and then shuts down for an instant and then reopens. Does anyone have this occur?? I have shutdown and restarted often.

I have a mac OS X and when I close it and reopen my screen opens and then shuts down for an instant and then reopens. Does anyone have this occur?? I have shutdown and restarted often.

A Safe Mode boot might help ..
Startup your Mac in Safe Mode
A Safe Mode boot takes much longer than a normal boot so be patient.
Once you are in Safe Mode, click Restart from the Apple () menu.
See if the problem persists.

Weblogic server 10.3 needs restart to reflect jsp changes.

Hello,
I am using weblogic 10.3.5. My problem is when I make changes to JSPs, it is not getting reflected when I refresh the page. Always I have to perform restart of the server.
I checked my weblogic.xml and I have the below configuration also.
<jsp-param>
<param-name>pageCheckSeconds</param-name>
<param-value>0</param-value>
</jsp-param>
I saw this thread: Weblogic server 10.3 needs restart to reflect jsp changes. , but it not helping me.
Can anyone help me?
Thanks.

you should also need to change the name space please try below
<?xml version = '1.0' encoding = 'windows-1252'?>
<weblogic-web-app xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="http://xmlns.oracle.com/weblogic/weblogic-web-app http://xmlns.oracle.com/weblogic/weblogic-web-app/1.1/weblogic-web-app.xsd"
xmlns="http://xmlns.oracle.com/weblogic/weblogic-web-app">
<jsp-descriptor>
<page-check-seconds>0</page-check-seconds>
</jsp-descriptor>
</weblogic-web-app>
http://docs.oracle.com/cd/E23943_01/web.1111/e13712/weblogic_xml.htm#BEIBCAJH
http://docs.oracle.com/cd/E23943_01/web.1111/e13712/weblogic_xml.htm#i1038490
Regards,
Sunil

Do SameSubnetDelay or SameSubnetThreshold setting need restart windows failover cluster ?

Hi ,
I set SameSubnetDelay=2000 and SameSubnetThreshold = 10,but after a failover, when i check the cluster log, we still found SameSubnetDelay and SameSubnetThreshold use default setting.
So i want to konw do these settings need restart windows failover cluster core resource group to take effect?
Our windows version: Windows 2008 R2 SP1
Many thanks.

Thanks for your reply.
After set up new values for these two settings , i checked the values use "cluster /prop " command, it indeed show new values.
But after a sql server cluster instance failover, i checked the cluster log to find the cause of failover ,in the cluster log it showed default values for these settings. There were two times like this.
I will keep watching this, and next time i will post the setting values and cluster log.

Does Arch have any tool to check what services needs restart?

Does Arch have any tool to check what services needs restart after software update just like `checkrestart` from Debian flavoured distros or `needs-restarting` from Red Hat ones?

Maybe there is some other temporary file that is not a library but deleted that slips through. I got my awk version now to replace my old hack code.
__pids="$(sudo lsof -F pfn |
awk '
/^n/{
# if this file is a deleted library or binary, show it
if (del == 1 && match($0, "bin|lib")) {
print pid;
del=0;
del = 0;
/^fDEL$/{
# the next file is deleted
del = 1;
/^p/{
# we check a new process
del = 0
pid = substr($0, 2)
}' |
sort -un |
paste -sd ' '
)" && [ -n "$__pids" ] && ps -p "$__pids" && unset __pids || unset __pids
Edit: Reorder logic, don't execute ps if no processes are found.
Last edited by progandy (2014-06-12 16:42:27)

5610 Xpress music: restarting often while speaking

Could you please let me know, how to overcome this problem: I am having Nokia 5610 Xpress music - it is getting restart often while speaking(two times per day). I brought this mobile 5 months back. I faced the same problem right from the first day. After one months software has been reinstalled even though that problem continues.
Any body help me to resolve this problem! I have checked it out with my friends who are having the same model(5610 Xpress music). They are facing the same problem, among five person four having the same problem.

Causes:
- Navi-key and camera button gets unnoticeably stuck causing it to be flooded with commands pointing to the music player and camera leading to a force system restart.
-One of your music files got corrupted
-Possible phone software corruption
-Mixing different music formats is not recommended as of the moment(on xpressmusic players only) - meaning putting files with MP3, eAAC, WMA files on one memory card could cause mixup and will lead to software malfunction
-Memory card fault
Possible solutions:
-Try checking the navi-key and camera button, make sure that they aren’t stuck.
-Replace your music files if you notice some file corruption
-Update your mobile phone’s software also known as firmware
-As much as possible don’t mix up files with different file types - this would also help the phone to save a much CPU power. Just stick to one - the eAACplus.
-Check if your memory card is faulty
Also posted on: http://xpressmusic.wordpress.com/2008/02/11/nokia-5610-restarting-problem/
Hope this helps

HT201363 I need restart my security question answer

I need restart my security question answer

Hi there al_wafy313,
You may find the information in the article below helpful.
Rescue email address and how to reset Apple ID security questions
http://support.apple.com/kb/ht5312
-Griff W.

IPhone 6 need to restart often

During the time when I was using a 4S (like 3 years, I very rarely had to restart the phone to correct an error like not connecting to WiFi, an app getting stuck or an app closing on itself etc. With my new 6 (64 GB) I seem to have to do that quite often. After the restart, no problems. Has anybody been experiencing the same problem? Can it be corrected?

I Guess your right I'll put a cade on the 6 If I had to get it I do like that they made the 4.7 the iphone 6 plus is way to big & that's the one that showing more bend on.....the iPhone 6 is super light tho....way lighter then the 5

Apple TV restart often needed to view YouTube subscriptions

Ever since 2.4 software update, when I leave the Apple TV on overnight, and get up the next day, and go to check out my YouTube subscriptions (and sometimes, my Favorites), I just get the spinning indicator. One time I let it go for 3 hours... A restart of the Apple TV fixes the problem, but that's a pain in the behind. Anyone else notice this?
Mark

Thanks, WD.
Just removed and re-added it on the AppleTV. Guess we'll find out tomorrow
Mark

T61 needs restart twice a day

Hi,
I'm using first version of T61 with windows vista ultimate.
I regulary update my system.
The problem is after sometime the system wont work properly, I wont be able to start new applications.
And few opened applications doesnt work.
If firefox is open sometimes it works.
And I have to restart the system and then system works fine for sometime.
Also when I hibernate and resume my system doesnt get internet.
Please somebody help me. Its really getting annoying.
Regards,
Giri

hi
if your browsing the net, it can become awful cluttered at times
get yourself a good cleaner like CCleaner and clear out all temp files regularly
also there is often no need to do a whole restart, just log off and log back on again resets lots of things
most importantly, turn prefetch etc off on your browsing and thikn about putting vista in the bin unlesss you got loadsa money for extra RAM
it eats it
hope something in there helps
T42 - T21 - Tecra 8200 all xp

Macbook Pro needs restart after sleep...

My Macbook Pro has starting doing this thing where the screen will go darker and it will tell me I need to restart by holding the power button. It happens pretty often when the computer wakes up from being in sleep mode. What's the deal?

Here's a console log detailing a wake sequence with failed Bluetooth and USB.
11/29/07 5:58:05 AM kernel hibernatepage_listsetall start
11/29/07 5:58:05 AM kernel hibernatepage_listsetall time: 334 ms
11/29/07 5:58:05 AM kernel pages 255568, wire 58460, act 36514, inact 14866, zf 73, throt 0, could discard act 17321 inact 127821 purgeable 513
11/29/07 5:58:05 AM kernel hibernatepage_listsetall found pageCount 109913
11/29/07 5:58:05 AM kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
11/29/07 5:58:05 AM kernel IOHibernatePollerOpen(0)
11/29/07 5:58:05 AM kernel writing 109692 pages
11/29/07 5:58:05 AM kernel image1Size 125079040
11/29/07 5:58:05 AM kernel all time: 4800 ms, comp time: 2057 ms, deco time: 0 ms,
11/29/07 5:58:05 AM kernel image 208890368, uncompressed 449298432 (109692), compressed 207754412 (46%), sum1 6d35adf1, sum2 4ccdde5c
11/29/07 5:58:05 AM kernel hibernatewriteimage done(0)
11/29/07 5:58:05 AM kernel sleep
11/29/07 5:58:05 AM kernel System Wake
11/29/07 5:58:05 AM kernel [IOAppleBluetoothHIDDriver][setReportWL][00-0a-95-3a-e1-ba] Could not send DATA command via interrupt channel
11/29/07 5:58:06 AM mDNSResponder[15] setsockopt - IPMULTICASTIF error 10.37.129.2 -1 errno 49 (Can't assign requested address)
11/29/07 5:58:06 AM mDNSResponder[15] mDNSPlatformSendUDP sendto failed to send packet on InterfaceID 00815600 en2/4 to 224.0.0.251:5353 skt 7 error -1 errno 49 (Can't assign requested address) 2256359361
11/29/07 5:58:06 AM mDNSResponder[15] setsockopt - IPMULTICASTIF error 10.211.55.2 -1 errno 49 (Can't assign requested address)
11/29/07 5:58:06 AM mDNSResponder[15] mDNSPlatformSendUDP sendto failed to send packet on InterfaceID 00819600 en3/4 to 224.0.0.251:5353 skt 7 error -1 errno 49 (Can't assign requested address) 2256359361
11/29/07 5:58:06 AM mDNSResponder[15] setsockopt - IPMULTICASTIF error 10.37.129.2 -1 errno 49 (Can't assign requested address)
11/29/07 5:58:06 AM mDNSResponder[15] mDNSPlatformSendUDP sendto failed to send packet on InterfaceID 00815600 en2/4 to 224.0.0.251:5353 skt 7 error -1 errno 49 (Can't assign requested address) 2256359361
11/29/07 5:58:06 AM mDNSResponder[15] setsockopt - IPMULTICASTIF error 10.211.55.2 -1 errno 49 (Can't assign requested address)
11/29/07 5:58:06 AM mDNSResponder[15] mDNSPlatformSendUDP sendto failed to send packet on InterfaceID 00819600 en3/4 to 224.0.0.251:5353 skt 7 error -1 errno 49 (Can't assign requested address) 2256359361
11/29/07 5:58:10 AM kernel AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
11/29/07 5:58:12 AM kernel AppleUSBHub::setPowerState(0x460e800, 2 -> 4) timed out after 10495 ms
11/29/07 5:58:12 AM kernel EIR is not supported.
11/29/07 5:58:16 AM kernel AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
11/29/07 5:58:17 AM authorizationhost[302] Failed to authenticate user cshotton (tDirStatus: -14090).
11/29/07 5:58:21 AM /usr/sbin/spindump[369] process 36 is being monitored
11/29/07 5:58:26 AM authorizationhost[302] Failed to authenticate user cshotton (tDirStatus: -14090).
11/29/07 5:58:33 AM authorizationhost[302] Failed to authenticate user cshotton (tDirStatus: -14090).
11/29/07 5:58:36 AM com.apple.SecurityServer[20] Failed to authorize right system.login.screensaver by client /System/Library/CoreServices/loginwindow.app for authorization created by /System/Library/CoreServices/loginwindow.app.
11/29/07 5:58:36 AM /usr/sbin/spindump[369] process 36 is being no longer being monitored
11/29/07 5:58:37 AM kernel hibernate image path: /var/vm/sleepimage
11/29/07 5:58:37 AM kernel sizeof(IOHibernateImageHeader) == 512
11/29/07 5:58:37 AM kernel Opened file /var/vm/sleepimage, size 2147483648, partition base 0xc805000, maxio 400000
11/29/07 5:58:37 AM kernel hibernate image major 14, minor 2, blocksize 512, pollers 4
11/29/07 5:58:37 AM kernel hibernateallocpages flags 00000000, gobbling 0 pages
11/29/07 5:58:42 AM kernel System SafeSleep
11/29/07 5:58:51 AM kernel hibernatepage_listsetall start
11/29/07 5:58:51 AM kernel hibernatepage_listsetall time: 332 ms
11/29/07 5:58:53 AM kernel pages 261630, wire 58337, act 42003, inact 12349, zf 74, throt 0, could discard act 18090 inact 127958 purgeable 2819
11/29/07 5:58:53 AM mDNSResponder[15] Note: Frequent transitions for interface en2 (FE80:0000:0000:0000:021C:42FF:FE00:0000); network traffic reduction measures in effect
11/29/07 5:58:53 AM kernel hibernatepage_listsetall found pageCount 112763
11/29/07 5:58:53 AM mDNSResponder[15] Note: Frequent transitions for interface en3 (FE80:0000:0000:0000:021C:42FF:FE00:0001); network traffic reduction measures in effect
11/29/07 5:58:53 AM kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
11/29/07 5:58:53 AM kernel IOHibernatePollerOpen(0)
11/29/07 5:58:53 AM kernel writing 112542 pages
11/29/07 5:58:53 AM kernel image1Size 125406208
11/29/07 5:58:53 AM kernel all time: 4773 ms, comp time: 2131 ms, deco time: 0 ms,
11/29/07 5:58:53 AM kernel image 216278016, uncompressed 460972032 (112542), compressed 215103712 (46%), sum1 491547db, sum2 bfc88fc9
11/29/07 5:58:53 AM kernel hibernatewriteimage done(0)
11/29/07 5:58:53 AM kernel sleep
11/29/07 5:58:53 AM kernel System Wake
11/29/07 5:58:56 AM mDNSResponder[15] Note: Frequent transitions for interface en1 (172.30.2.41); network traffic reduction measures in effect
11/29/07 5:58:56 AM mDNSResponder[15] Note: Frequent transitions for interface en1 (FE80:0000:0000:0000:021C:B3FF:FEC5:BB5E); network traffic reduction measures in effect
11/29/07 5:58:58 AM kernel AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
11/29/07 5:59:00 AM kernel [IOAppleBluetoothHIDDriver][setReportWL][00-0a-95-3a-e1-ba] Could not send DATA command via interrupt channel
11/29/07 5:59:03 AM kernel AppleUSBHub::setPowerState(0x460e800, 2 -> 4) timed out after 10964 ms
11/29/07 5:59:03 AM kernel EIR is not supported.
11/29/07 5:59:06 AM kernel AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
11/29/07 5:59:08 AM /usr/sbin/spindump[369] process 36 is being monitored
11/29/07 5:59:10 AM /usr/sbin/spindump[369] process 36 is being no longer being monitored
11/29/07 6:00:23 AM kernel BT_USB Controller: SuspendDevice(0) failed with error e0004051
11/29/07 6:00:23 AM kernel BT_USB Controller: SuspendDevice(0) we are still connected to our hub so .. plain reset 0x4693a00
11/29/07 6:00:54 AM kernel CSRUSBBluetoothHCIController::setPowerState(0x4704000, 1 -> 2) timed out after 50695 ms
11/29/07 6:03:39 AM /usr/sbin/ocspd[390] starting

Constant power button and greyed out screen (needed restart)

So I'll use my computer in the normal way that I would (ichat, MSWord,iTunes and maybe some other programs) and every now and again (more often than that actually) the computer screen would go dark and I would get a notification that I need to restart my computer in the way of holding down the power button.
I've run though disk utilities and fixed whatever problems it could. I've also run the Maintanence automation from the download site.
This is usually what will happen:
I'll use my computer normally
a program will quit unexpectadly
a) annother program will quit in the same way and then the computer will crash
b) the computer will crash
I've had this computer for a year and this only started happening a month or so after a full reinstalation of MaxOSX (annual cleanup)
What should I do?

After doing more reading into my issue I figured what was going on was my Kernel was Panicking (can I use the terms like that or is it just Kernel Panic... anyway)
so I went ahead and found the logs on it and as you can see, it's happened a few times SO... without further stalling:
Thu Jun 15 23:00:31 2006
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000080610050 PC=0x000000000003FCFC
Latest crash info for cpu 0:
Exception state (sv=0x44E00000)
PC=0x0003FCFC; MSR=0x00009030; DAR=0x80610050; DSISR=0x40000000; LR=0x0003FCE4; R1=0x21F1BCF0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0282F4D0 0x001401B0 0x0016350C 0x0028F804 0x00295358 0x002AABD4
0x000ABEB0 0x2F2F2F2F
Proceeding back via exception chain:
Exception state (sv=0x44E00000)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x383DEA00)
PC=0x9001B1EC; MSR=0x0200F030; DAR=0x00880000; DSISR=0x40000000; LR=0x913E6748; R1=0xF01803F0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x44E00000)
PC=0x0003FCFC; MSR=0x00009030; DAR=0x80610050; DSISR=0x40000000; LR=0x0003FCE4; R1=0x21F1BCF0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0282F4D0 0x001401B0 0x0016350C 0x0028F804 0x00295358 0x002AABD4
0x000ABEB0 0x2F2F2F2F
Exception state (sv=0x383DEA00)
PC=0x9001B1EC; MSR=0x0200F030; DAR=0x00880000; DSISR=0x40000000; LR=0x913E6748; R1=0xF01803F0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Tue Jun 20 17:52:10 2006
Unresolved kernel trap(cpu 0): 0x400 - Inst access DAR=0x000000000000D8EC PC=0x0000000000000000
Latest crash info for cpu 0:
Exception state (sv=0x3818E280)
PC=0x00000000; MSR=0x40009030; DAR=0x0000D8EC; DSISR=0x40000000; LR=0x0025EF70; R1=0x22073D00; XCP=0x00000010 (0x400 - Inst access)
Backtrace:
0x00000000 0x0025F174 0x0025D26C 0x0025CFCC 0x002AABD4 0x000ABEB0
0x73747269
backtrace terminated - frame not mapped or invalid: 0xF00FF840
Proceeding back via exception chain:
Exception state (sv=0x3818E280)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x37DFF000)
PC=0x9001494C; MSR=0x0000D030; DAR=0xA130C1EB; DSISR=0x40000000; LR=0x907DCC74; R1=0xF00FF840; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0004): 0x400 - Inst access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x3818E280)
PC=0x00000000; MSR=0x40009030; DAR=0x0000D8EC; DSISR=0x40000000; LR=0x0025EF70; R1=0x22073D00; XCP=0x00000010 (0x400 - Inst access)
Backtrace:
0x00000000 0x0025F174 0x0025D26C 0x0025CFCC 0x002AABD4 0x000ABEB0
0x73747269
backtrace terminated - frame not mapped or invalid: 0xF00FF840
Exception state (sv=0x37DFF000)
PC=0x9001494C; MSR=0x0000D030; DAR=0xA130C1EB; DSISR=0x40000000; LR=0x907DCC74; R1=0xF00FF840; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Wed Jun 21 01:08:21 2006
Unresolved kernel trap(cpu 0): 0x400 - Inst access DAR=0x000000000000D8EC PC=0x0000000000000000
Latest crash info for cpu 0:
Exception state (sv=0x3818E280)
PC=0x00000000; MSR=0x40009030; DAR=0x0000D8EC; DSISR=0x40000000; LR=0x0025EF70; R1=0x22073D00; XCP=0x00000010 (0x400 - Inst access)
Backtrace:
0x00000000 0x0025F174 0x0025D26C 0x0025CFCC 0x002AABD4 0x000ABEB0
0x73747269
backtrace terminated - frame not mapped or invalid: 0xF00FF840
Proceeding back via exception chain:
Exception state (sv=0x3818E280)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x37DFF000)
PC=0x9001494C; MSR=0x0000D030; DAR=0xA130C1EB; DSISR=0x40000000; LR=0x907DCC74; R1=0xF00FF840; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0004): 0x400 - Inst access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x3818E280)
PC=0x00000000; MSR=0x40009030; DAR=0x0000D8EC; DSISR=0x40000000; LR=0x0025EF70; R1=0x22073D00; XCP=0x00000010 (0x400 - Inst access)
Backtrace:
0x00000000 0x0025F174 0x0025D26C 0x0025CFCC 0x002AABD4 0x000ABEB0
0x73747269
backtrace terminated - frame not mapped or invalid: 0xF00FF840
Exception state (sv=0x37DFF000)
PC=0x9001494C; MSR=0x0000D030; DAR=0xA130C1EB; DSISR=0x40000000; LR=0x907DCC74; R1=0xF00FF840; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Wed Jun 21 11:02:07 2006
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000003CF73AC PC=0x000000000003ECC8
Latest crash info for cpu 0:
Exception state (sv=0x3867A280)
PC=0x0003ECC8; MSR=0x00001030; DAR=0x03CF73AC; DSISR=0x40000000; LR=0x0003ED2C; R1=0x21FD3AC0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x00000000 0x0003ED2C 0x0003F0C0 0x0001CF90 0x0001CE78 0x0001AC44
0x00029574 0x0002E614 0x0003C744 0x000A9894
Proceeding back via exception chain:
Exception state (sv=0x3867A280)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x3846A500)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x3867A280)
PC=0x0003ECC8; MSR=0x00001030; DAR=0x03CF73AC; DSISR=0x40000000; LR=0x0003ED2C; R1=0x21FD3AC0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x00000000 0x0003ED2C 0x0003F0C0 0x0001CF90 0x0001CE78 0x0001AC44
0x00029574 0x0002E614 0x0003C744 0x000A9894
Exception state (sv=0x3846A500)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Wed Jun 21 14:10:27 2006
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000001 PC=0x00000000001026EC
Latest crash info for cpu 0:
Exception state (sv=0x456C0780)
PC=0x001026EC; MSR=0x00001030; DAR=0x00000001; DSISR=0x40000000; LR=0x001026E0; R1=0x220E3490; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x001026E0 0x00102BD8 0x0002CE94 0x002741FC 0x00274670 0x00008ED0
0x02768EC8
backtrace terminated - frame not mapped or invalid: 0xF0F00000
Proceeding back via exception chain:
Exception state (sv=0x456C0780)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x388E7780)
PC=0x90019ACC; MSR=0x0000D930; DAR=0x37FEDFC6; DSISR=0x40000000; LR=0x000115E0; R1=0xBFFFF400; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x456C0780)
PC=0x001026EC; MSR=0x00001030; DAR=0x00000001; DSISR=0x40000000; LR=0x001026E0; R1=0x220E3490; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x001026E0 0x00102BD8 0x0002CE94 0x002741FC 0x00274670 0x00008ED0
0x02768EC8
backtrace terminated - frame not mapped or invalid: 0xF0F00000
Exception state (sv=0x388E7780)
PC=0x90019ACC; MSR=0x0000D930; DAR=0x37FEDFC6; DSISR=0x40000000; LR=0x000115E0; R1=0xBFFFF400; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Fri Jun 23 09:54:51 2006
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x000000002C1D9000 PC=0x000000000094F040
Latest crash info for cpu 0:
Exception state (sv=0x3846F780)
PC=0x0094F040; MSR=0x0000B030; DAR=0x2C1D9000; DSISR=0x42000000; LR=0x0094EFC0; R1=0x22053BF0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0094EFC0 0x0092CFAC 0x002E87E0 0x002EA6AC 0x0008C4B0 0x000291C0
0x000233AC 0x000AC02C 0x67743B49
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x925000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x459000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.1)@0x843000
dependency: com.apple.iokit.IONDRVSupport(1.4.1)@0x867000
Proceeding back via exception chain:
Exception state (sv=0x3846F780)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x38535780)
PC=0x9000B0A8; MSR=0x0200F030; DAR=0x000E9F50; DSISR=0x40000000; LR=0x9000AFFC; R1=0xBFFFE8E0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x3846F780)
PC=0x0094F040; MSR=0x0000B030; DAR=0x2C1D9000; DSISR=0x42000000; LR=0x0094EFC0; R1=0x22053BF0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0094EFC0 0x0092CFAC 0x002E87E0 0x002EA6AC 0x0008C4B0 0x000291C0
0x000233AC 0x000AC02C 0x67743B49
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x925000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x459000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.1)@0x843000
dependency: com.apple.iokit.IONDRVSupport(1.4.1)@0x867000
Exception state (sv=0x38535780)
PC=0x9000B0A8; MSR=0x0200F030; DAR=0x000E9F50; DSISR=0x40000000; LR=0x9000AFFC; R1=0xBFFFE8E0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Fri Jun 23 11:58:12 2006
panic(cpu 0 caller 0x000A8D80): Uncorrectable machine check: pc = 000000000009D78C, msr = 0000000000141000, dsisr = 0A000000, dar = 000000008FE532C8
AsyncSrc = 0000000000000000, CoreFIR = 0000000000000000
L2FIR = 0000000000000000, BusFir = 0000000000000000
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8D80 0x000A8010 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x39DFD780)
PC=0x0009D78C; MSR=0x00141000; DAR=0x8FE532C8; DSISR=0x0A000000; LR=0x0009D6C8; R1=0x21FC34D0; XCP=0x00000008 (0x200 - Machine check)
Backtrace:
0x030DE948 0x0009A0A8 0x00098EB4 0x0006AA14 0x0006B100 0x0006B5F0
0x00038070 0x002658B8 0x002722EC 0x00025250 0x000AC138 0x00026CF4 0x000A8B3C 0x000A88FC
0x000ABD00
Exception state (sv=0x37B23500)
PC=0x90A3AF80; MSR=0x0000D030; DAR=0x00000000; DSISR=0x40000000; LR=0x90A3AED0; R1=0xBFFFF5E0; XCP=0x00000003 (Unknown)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Fri Jun 23 13:10:39 2006
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000180 PC=0x00000000002D6F08
Latest crash info for cpu 0:
Exception state (sv=0x383A5500)
PC=0x002D6F08; MSR=0x00009030; DAR=0x00000180; DSISR=0x40000000; LR=0x0092939C; R1=0x2205BC70; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0092B634 0x0092939C 0x0092A904 0x0092A9E0 0x002D0940 0x002CF808
0x000A9894
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x925000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x459000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.1)@0x8ba000
dependency: com.apple.iokit.IONDRVSupport(1.4.1)@0x8de000
Proceeding back via exception chain:
Exception state (sv=0x383A5500)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x3D415C80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x383A5500)
PC=0x002D6F08; MSR=0x00009030; DAR=0x00000180; DSISR=0x40000000; LR=0x0092939C; R1=0x2205BC70; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0092B634 0x0092939C 0x0092A904 0x0092A9E0 0x002D0940 0x002CF808
0x000A9894
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x925000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x459000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.1)@0x8ba000
dependency: com.apple.iokit.IONDRVSupport(1.4.1)@0x8de000
Exception state (sv=0x3D415C80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
Fri Jun 23 13:36:23 2006
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000180 PC=0x00000000002D6F08
Latest crash info for cpu 0:
Exception state (sv=0x383A5500)
PC=0x002D6F08; MSR=0x00009030; DAR=0x00000180; DSISR=0x40000000; LR=0x0092939C; R1=0x2205BC70; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0092B634 0x0092939C 0x0092A904 0x0092A9E0 0x002D0940 0x002CF808
0x000A9894
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x925000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x459000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.1)@0x8ba000
dependency: com.apple.iokit.IONDRVSupport(1.4.1)@0x8de000
Proceeding back via exception chain:
Exception state (sv=0x383A5500)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x3D415C80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x000A8384 0x000ABD00
Proceeding back via exception chain:
Exception state (sv=0x383A5500)
PC=0x002D6F08; MSR=0x00009030; DAR=0x00000180; DSISR=0x40000000; LR=0x0092939C; R1=0x2205BC70; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0092B634 0x0092939C 0x0092A904 0x0092A9E0 0x002D0940 0x002CF808
0x000A9894
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x925000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x459000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.1)@0x8ba000
dependency: com.apple.iokit.IONDRVSupport(1.4.1)@0x8de000
Exception state (sv=0x3D415C80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70.obj~1/RELEASE_PPC
As a note I really do appreciate people looking at my issue and thank anyone in advance what would take a look at this.
Cheers

Apple TV needs Restart for Airplay especially after resuming from Sleep Mode

1. I always have to restart my Apple TV for Airplay when I resume it from Sleep Mode. Neither my MAC not my PC nor my iPhone/iPad can connect to Airplay if it's not retsarted. I did a complete Factory Reset of Apple TV thinking it would be the best way of troubleshooting but in vein. Any help/suggestion/tips from anybody please?
2. Also - Does Apple TV needs internet always for Airplay? I guess that should work on the LAN even if there is no internet connectivity, Correct?
Regards,

Hey loftysub,
I'd check out the following article, it should be able to help you out:
Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS4215
Cheers,
David

AX Needing restart often

Similar Messages

Maybe you are looking for