B200M3 and Vsphere 5.1 - Unable to set NIC speed to 10gb full duplex

Hi,
My first post here!
I got 4 B200M3 blades with VIC 1240 and 1280. I have installed vSphere 5.1 on them. The blades are configed with a number of NIC's.
The NIC's get a speed of 20gb full duplex(set on auto negotiation) and i would like to set them to 10gb full duplex. When i try to change it in vSphere i get an error message
"Call "HostNetworkSystem.UpdatePhysicalNicLinkSpeed" for object "networkSystem-1264" on vCenter Server "xxxxxxxxxxxxxx" failed.
Operation failed, diagnostics report: Forcing 1000Mbps or faster may not be supported on this network device, please use auto-negotiation instead"
After some searching it looks like you sometimes have to upgrade vSphere with new drivers to get these things to work?
Anyone got any ideas that can help me?
// Fredrik

Hi Fredrik,
A few quick questions:
1) What is the driver type and the version on the vnics? here is the HCL for the required driver versions:
http://www.cisco.com/en/US/docs/unified_computing/ucs/interoperability/matrix/r_hcl_B_rel2.04.pdf
2) Did you install 5.1 direct or did you upgrade from 5.0? For this blade you need to use the CISCO OEM Custom ESXi image. We still do not have the 5.1 image published, however the 5.0 and 5.0 U1 are avaiable for use. Here is the download location:
https://my.vmware.com/group/vmware/details?downloadGroup=CISCO-ESXI-5.0.0-U1-28AUG2012&productId=229
Thanks!
./Abhinav

Similar Messages

  • Unable to set the speed on dot11Radio Interface

    Hello Experts,
    I have number of 1130ag access points in our network. The problem i am facing is that when I tried to set the speed on the dot11Radio 0 and 1 interface it doesn't appear
    This is the command I am using:
    interface dot11Radio 0
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
    Please can someone help me.

    Hi,
    The configurations that you are entering.. that is..
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
    is the Default config for 802.11G and by nature the default configurationas will not appear in the running config.. another example is.. By default Aironet Extentions are enabled on the AP runing config, and in the Show run you will see that.. but when you isue the command no dot11 extension aironet thne this command wil show up!! please make the change and then you will be able to see.. here is the link as well which can be used to set the values..
    http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap6-radio.html#wp1101903
    lemme know if this answered your question
    Regards
    Surendra

  • HT1695 I am not able to update the calendar app or reminder app. There is no ability to update and siri is also unable to set a reminder or update the calendar. This is a new phone.

    I am not able to update my calendar or reminders. I've looked at other iPhones and they have a + button to allow you to update. How do I fix this. Also, Siri also does not update the reminders or calendar.
    Please help

    Earlier iOS apps are becoming increasingly difficult to find.  You may want to look at VintApps, new in the Apple app store, that makes this much easier.
    Vintapps info/support:  https://www.facebook.com/VintApps313
    For a web based method see,
    https://sites.google.com/site/appleclubfhs/support/advice-and-articles/finding-a pps-for-older-devices
    Although I wrote my 99 cent app specifically to help solve this problem, I need to add that "I may receive some form of compensation, financial or otherwise, from my recommendation or link."
    Be sure to backup your current apps on earlier devices.  Once the vendor updates them past your maximum iOS, they can not be downloaded again.

  • Unable to set custom speed to motion path on Camera

    This is a followup question to "Controlling speed along motion paths"
    (Many thanks to Mark Spencer and specialcase for the their excellent insights getting me this far =)
    After experimenting with motion paths and realizing they were indeed what I was looking for, I set up my project so that the camera would follow specific paths along 2d images. Everything worked perfectly until I tried to modify the speed along which the camera travels along those paths.
    In the motion path, in the speed drop down menu, I can select Constant, Ease in etc.... all the way to Custom, but they work slightly differently than I expected: while before (ie. applying motion curves to objects as opposed to the camera) I was able to getting a diagonal line in the Keyframe Editor where I could modify keyframes using bezier curves to adjust the speed, now, choosing the various speed options appears to change the "Transform.Position.X" and "Transform.Position.Y" curves directly.
    When I select "Custom", "Motion path" and Custom Speed" appear in the keyframe menu above the Camera drop down, but its curve appears only as a dotted, completely horizontal line in the graphing window. The "Transform.Position.X" and "Transform.Position.Y" curves also revert to horizontal dotted lines. If I try to add curves to the custom speed line, the X and Y curves remain horizontal and the camera does not move.
    Is there some reason I cannot get custom speeds for cameras without losing my motion path data?
    Is there some way to work around this?
    Thanks again for all of your help,
    Tim

    I'm not sure if there is some setting I have wrong:
    When I try this, while I am able to set keyframes, the motion path data is reset. (ie. the Transform X and Transform Y curves reset to 0).
    In the Keyframe Editor, I can make new curves for the X and Y values and for Timing, but the camera does not follow the motion path, it follows the new x and y curves. Trying to get those curves to match the motion path exactly is a large hassle.
    This might help:
    If I apply the motion path to an shape rather than to the camera, everything works perfectly (the object moves along the motion path, and I am able to set keyframes for the Custom Speed curve with no problems whatsoever). If I then copy the motion path directly from the shape and paste it to the camera layer, the path appears as a red curve (as it should), but the camera does not move.
    Is there some way I can upload the motion file so that you can see what exactly is going on?
    Thanks again,
    Tim

  • How do I set ethernet speed to 100 Full?

    Right now we connect at 100 half duplex. I need to change our Mac lab to 100 full but I can't find how to do it. We are running Imac G5's with Tiger. Please help. Thanks in advance

    System Preferences>Network>Show:>Ethernet>Ethernet Tab>Configure=Manually, Speed=100, Duplex=Full... Apply.

  • Service Desk Unable to set status to Customer Action and Proposed Solution

    Hi Everyone,
    We are unable to set a service desk issue to the status Customer Action or Proposed solution.
    I have someone create a new issue in the bakend system and when I receive the issue I assign it to myself as the processor. When I try to set teh status to Customer action it is grayed out.
    I have checked the following:
    1. As a test I assigned My user with sap_all profile so does not appear to be authroisation related
    2. The status profile has all six standard values (New, customer action, In Process, Sent to SAP, Proposed Solution, Confirmed).
    3. The transaction types have been defined using the standard profiles for Text Det. Procedure, Partnet Determination Procedure, Status Profile. The Partner Function ORG is set to Sold-To-Party , The date profile is a SRV_SLA_ITEM and the Action profile is set to SLFN0001_ADVANCED. The Org Data Prof is set to a customer defined one: ZSSC000000001.
    4. I have checked transaction ppoma_crm and the org structure and my user is assigned to a team lead position.
    Your assistance is greatly appreciated.
    Michael

    Hi Michael,
    please check your status profile for the "lowest status no." and "highest status no." values of the status values as Alex mentioned!
    You can find this in SPRO under "SAP Solution Manager> Scenario-Specific Settings>Service Desk>Service Desk>Status Profile".
    If the "high" value of the status "New" is lower than the status number of status "Customer Action" than you can not set the message from "New" to "Customer Action"!
    Hope this helps,
    Christoph

  • I have an iPhone 4s, and I reset the content and setting. It turned on, I chose English, Australia, and now, I am unable to connect/activate my iPhone through Wi-Fi, and for an unknown reason, it will not allow me to use cellular data or iTunes.

    I have an iPhone 4s, and I reset the content and setting. It turned on, I chose English, Australia, and now, I am unable to connect/activate my iPhone through Wi-Fi, and for an unknown reason, it will not allow me to use cellular data or iTunes. I'm not sure of what to do. It's quite frustrating, and all I need is advice, and help. I would much appreciate it. Thank-you.

    In order to download to your phone over the air, you need to be connected to WiFi.
    It's possible the Internet connection through Verizon is not stable enough for the downlaod to begin (it is a very large download).
    You might want to head over to Starbucks with your laptop for the afternoon and see if you can download it over their WiFi.

  • Please Help, After Kernel panic restart failed- apple swirl(6 hrs), SafeMode-failed, SUMode-sucess. Could not unmount disk to erase. Repair permissions-multiple fail errors:unable to set permissions on... unable to set owner and group...

    Please Help, I deleted an account that was the same name as the administrator but was not the administrator. Also a samsung galaxy s phone was charging through the usb port.
    I closed out a program and got a message that the temp file could not be stored/saved.
    Then a Kernel panic message occurred and restart was necessary.
    The restart resulted in the screen with the apple logo and a continous swirl for 6+hrs,
    Attempted Safe Mode start up, unsuccessful,
    Single User Mode-sucess.
    Ran $ fsck_hfs -rfd /dev/disk0s2 Ran several times repairs made with one which remained. something about a node.
    No change in start up attempts
    Started with install CD matching current OS 10.6
    Ran Disk Utility Repair Permissions resulting in multiple errors:
    One line/error
    Warning: SUID file /////Ardagent has been modified and will not be repaired
    144 lines/errors of this type of series of lines
    Group permissions differ on...should be drwxr-xr-x, they are -rw-r--r-- .
    permissions differ on...should be drwxr-xr-x, they are -rw-r--r-- .
    unable to set owner and group...error 22: Invalid Argument
    unable to set permissions on...error 22: Invalid Argument
    Ran Repair Disk, result:
    Error: Could not unmount disk (in red)
    Ran Verify Disk, result:
    The volume HD appears to be ok (in green)
    Next I attempted to erase the dist to start from scratch since I have data backed up on time machine.
    Error message box
    Volume Erase failed
    Volume Erase failed with error:
    Could not unmount disk
    I am looking to solve without buying DiskWarrior unless only resort.

    So it looks like  solved it for now I will update later. What I did was after starting from the install cd for the 10.6 system I ran from terminal ran:
    diskutil disablejournaling /dev/disk0s2
    diskutil disableownership /dev/disk0s2
    diskutil repairPermissions /dev/disk0s2
    then i closed terminal and then when to disk utility and chose to repair disk with results all was fine. Then ran repair permissions and got similar results from terminal function next I erased disk and then chose to restore from time machine and it is now restoring! yea!

  • Unable to set columns under Layout Margins and Columns

    On certain pages in my 40 page document, I am unable to set the number of columns by using Layout>Margins and Columns. The columns option is dimmed out. I have tried to set them on a blank page and pages where columns were previously set (I can see the guides). I am using a single Master for page numbering and it is applied to every page in the document. There are pages where I can set the columns. I've done some page comparison and can't find the setting that might control this. Using InDesign CS6 on Windows. Thank you.

    Why are you not using multiple column text frames instead of 2 text frames with columns on the master page? This would give more flexiblity.

  • I restored my ipad but i was unable to activate it because it is askimg me for the apple id and password eith which i originally set it up. I know the apple id although i do not remember ever using it but i cannot remember the password.

    I restored my ipad but i was unable to activate it because it is askimg me for the apple id and password eith which i originally set it up. I know the apple id although i do not remember ever using it but i cannot remember the password. I have tried everything from reserting my password to trying different passwords but it asks me for a custom question that i dont remember creating.

    You need to use Apple's iForgot service or contact their Account Security team.
    (123152)

  • Oracle 9i - Unable to set /PAE and /3GB Switch in Windows 2003 Server SP2

    Hi
    I was wondering if anyone had any experience on Windows 2003 Server (SP2) with setting /PAE and /3GB switches.
    I am unable to set both together, setting one or the other works fine in the boot.ini.
    Oracle seem to think you can set both but it causes my OS to crash/become unstable.
    Has anyone set both switches together on 32 bit Windows 2003 Server successfully?
    I am using Oracle 9.2.0.3 Enterprise Edition.
    Thanks

    The server is new. But we installed 10g before 11g was available. Then upgraded to 11g, so it is a little mess. What the oracle installer should have done in a fresh install, it is maybe not what the server has now.
    I have checked for memory issues, processor issues, http errors, every EM setting and metric, and everything looks just right, but the applications are slow and the users are upset.
    Anyway, thanks for the advice. Maybe we will need to re-install everything or go back to 10g on Windows 2003 Server x32. That configuration was working fine before rushing into 11g.

  • Unable to set parental controls on itunes b/c my username and password are not correct.  How do I reset them?  There is no prompt to give any clues what they are.

    unable to set parental controls on Itunes b/c my user name and password got rejected.  How do I reset them or figure out my username and password?

    This is a user to user support forum.  We are all iphone users just like you.
    You are not addressing Apple here at all.
    This is an odd way to ask your fellow iphone users for help. Berating oterh users will not help you.
    "it's too fragile"
    No it is not.  i have never damaged one, nor has anyone I know.
    " U loose data when Ur phone is locked"
    No you don't.  Why do you think this?
    "and there is no customer support!!!  "
    Wrong yet again.  Apple has an 800 number and they have many retail stores and they have support articles that you can access using the search bar. Or you can contact them throgh express lane online
    "but I will go back with Blackberry "
    Please do.
    Good ridance

  • Unable to set network time and date

    My Applet TV2 is unable to set the network time and date making it so I cannot login to my itunes account so not Netflix or anything making it pointless. I have tried adjusting my router settings (although I've used the same router for over and year and this just started randomly) I have ensured Port's 123 are open, I've restored the ATV2 4 times and have reset my router. I've seen links showing how to use SSh to set the time but I'm unsure if that will work. Any help is appreciated as I'm at a loss at this point

    Welcome to the Apple Community.
    Of the things I've seen work for people in the community you seem to have done most of them, but did you try these.
    Restart Apple TV by removing ALL the cables for a moment or two.
    Ensure that the DNS address's used by the Apple TV and the router are the same and are the address recommended by your ISP.

  • I am unable to set up my iCloud as won't let me accept terms and conditions, then says unable to connect to server.  Any help would be appreciated :)

    Please can someone help, I am just trying to set up iCloud on my iPad.  When I click on accept terms and conditions it says unable to connect to server? I have googled how to do this, forums suggest to open a find friends app, then try to reconnect.  It still doesn't work.  Any help would be appreciated, thanks.

    Check this. Settings>General>Date and Time>Set Automatically>On. Make sure that the time zone setting is correct as well.

  • HT4557 I'm trying to set up my iphone for home sharing and its says unable to set up home sharing. My password is correct, I've tried it three times with the same message. Any help?

    I'm trying to set up my iphone for home sharing and its says unable to set up home sharing. My password is correct, I've tried it three times with the same message. Any help?

    Hello daltonfromgbr
    Check out the article below to troubleshoot you issue with connecting to Home Sharing. It will walk you through checking firewall settings as well as your network connection.
    Troubleshooting Home Sharing
    http://support.apple.com/kb/ts2972
    Regards,
    -Norm G.

Maybe you are looking for