B210a will not print after changing router\modem

b210a will not print after changing router\modem. Says it is connected to network, but will not print and says unavailable

Good morning,
Please use the second section of the following article to fix:
http://www8.hp.com/au/en/campaigns/wireless-printing-center/reconfiguring-system-help3.html?jumpid=r...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Have a Canon MX860 and the magenta will not print after several deep cleanings

Have a Canon MX860 and the magenta will not print after several deep cleanings

Hello allenaeifert.
Unfortunately, if the issue persists after deep cleanings have been performed, we would have to advise that you contact our support group at 1-800-OKCANON for additional assistance with this issue.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Hi there can anyone help as i am unable to contact Apple for support with my printer which will not print after recent software update? this is the email i tried to send to apple with no success, can anyone help please.......Dear Apple, I'm pulling my hai

Hi there,
Can anyone out there help, after a recent Apple software update my Epson Stylus Photo RX640 will no longer print, every other aspect of the printer works fine including the scanner but it just will not print, I sent an email to apple but all i got was an automated reply directing me to their support page, the email i sent is below this explains in full what the problem is & what i have done to try & fix this problem.
Dear Apple,
I'm pulling my hair out after a recent software update from apple, since this update my Epson Stylus Photo RX640 will not print, every other function of the printer including the scanner works fine,
Please see attached file of the error message coming up in the print queue.
I have spent days trying to fix this, i have been onto Epsons website & followed their resolution for this error message to no avail, after contacting them again with the results i got an email back saying : In response to your email, the RX640 will use an inbox or gutenprint driver on Mac OS X 10.6.8, it is not compatible with an Epson driver.
I have also tried re-installing drivers from original Discs for the printer but it still will not print, obviously this error has been caused by Apple's latest software update, when are Apple going to fix this problem? i need my printer working ASAP.
Regards
Brian
PS i obviously can't attach the error message so here it is: Error:/Library/Printer/Epson/inkjetprinter 2/filter/rastertoescpll.app/contents/mac os/rastertoescpll/failed
Thank You all in advance
Regards
Brian

It is hardly Apple's fault that Epson can't/won't update their driver, but at least Epson suggest that you use the Gutenprint driver, which in any case is far better that what Epson offer.
You can get it here:
http://gimp-print.sourceforge.net/
You can download the latest version from here:
http://sourceforge.net/projects/gimp-print/
Have you downloaded the recent Apple update to Epson drivers?
http://support.apple.com/kb/DL1398

HP Officejet Pro 8500 Wireless (Vista x64) Will not print after Sleep Mode

Hello,
As the title says the printer does not print after coming back from sleep mode. Before entering sleep mode the printer works fine and is responsive. After coming back from sleep mode the printer is still responsive (buttons on the touch screen can be pressed) but unfortunately does not accept any print jobs. Currently, I restart the printer to get it to print. It is connected wirelessly through WRT610N Linksys Router. Any suggestions or solutions would be greatly appreciated.
-Artem Durytskyy

I have been having the same problem all during my warranty period. But no one ever told me it was a firmware problem until two days ago connected to the sleep mode for the wireless one. Supposedly, they have downloads for wire ones now online which I found for 909a and 909b, but not 909g which is wireless. Now I am out of warranty and they won't replace it. I have a long history with tech support since early 2010. Right now, they are sending me a power adapter to try, said to turn off sleep mode (which I dont' know how). Then I told them I found online a firmware download, Apr 2010 to update firmware. My current version is different that the one listed for the download. So, I'm going back to TS to have them fool with it. Has anything worked for you?
Officejet Pro 8500 Wireless, A909g. It's been a problem from the beginning

Epson Stylus CX7300 will not print after software update

After doing the latest update for my Epson Stylus CX7300 printer it will not print. When i open the printer utility it comes up with a communication error. I can still scan documents but i can't print or even print a test page, check ink levels etc.

Hi Kerry Bonney,
Welcome to the Apple Support Communities!
If you are having issues printing after running a software update I would recommend using the troubleshooting steps in the following article. It sounds like you have already completed some of these steps, but I would recommend reading over and working through the steps provided in this article.
Troubleshooting printer issues in OS X
http://support.apple.com/kb/TS3147
Have a great day,
Joe

HP Photosmart B210a will not print black ink on plain paper... only on photo paper.

Hi, I have an HP Photosmart B210a that wont print black ink. I have used a whole set of ink cartridges by cleaning the print heads, allignment etc. I just installed ALL NEW cartridges and the sae thing is ocurring. I have replaced plenty of cartridges and am experienced. Just all of a sudden one day the printer stopped printing black ink on plain paper documents like with MS Word, excel and PDF, etc. It's not set to greyscale either, actually it wont even print grey! However, if I go to a photo with plenty of black in it, it will print it JUST FINE!!! I'm at my wits end! I have followed EVERY head cleaning advice in the forums but it will not print black in except on photos... Please help!!!!

The document here may help, although you have likley already done most of the steps. Be sure to check the vents. If the above does not resolve black not printing on your Photosmart b210a the post here may help.
The black cartridge uses pigmented ink which is not compatible with photo paper. Although the printer appears to be printing black properly on photo paper it is actually using color mixed together to produce black in this case.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Epson rx680 will not print after apple update print driver

I have an Epson RX680 which worked perfectly until I allowed the latest apple update to be installed with newest epson printer driver. It now will not print but comes back with a rasce blah blah error. Tried restoring to the previous software but to no avail.

https://discussions.apple.com/thread/5233149

Canon MP450 Printer will not print after OS X 10.4.9 Upgrade

After installing the software update, I'm unable to print. I went to download the lastest driver from Canon and installed it but I'm still having the same problem. Does anyone know how to revert back to OS X 10.4.8, without having to reinstall from the OS X install discs? Everything was working fine then, this is what I get for being an "early adopter." I should have looked through the online forums first. This reminds all to well of the issues I have when using the "PC." I guess I have to wait until Canon updates their drivers , but that means I'll have to use my PC to print everything. Please somebody help...
2.0 GHz - Intel Core Duo White Macbook - 80 GB HD - 1GB RAM Mac OS X (10.4.8) 30GB Blk iPod Video 1G - 8GB Blk Nano 2G - 4GB Slvr Nano 2G - 1GB Slv Shuffle 2G

No point in waiting for Canon. Their drivers are fine. The update has caused the problem, probably because it has reset permissions on some files. But for the record, I checked the pre-release version of 4.9 a month ago with a number of Canon drivers and they all worked fine. So this is not a compatibility issue with 4.9, it has something to do with the way your Mac is configured. But don't despair, this has happened with just about every previous update and you will not be the only way to have printing problems after updating to 10.4.9.
First of all you can try running the Repair Disk Permissions. This usually resolves printing issues after an update. This can be found in Applications > Utilities > Disk Utility.
However, since you reinstalled the driver you could have created file version conflicts, so if the permissions doesn't help, then try opening the Printer Setup Utility, clicking on the title and selecting Reset Printing System. This will delete the printer and the drivers you have installed for the MP450. Restart the Mac once this is complete and then once it is running again, run the driver installation again for the MP and then add the printer again.
Paul

My hp4530 will not print after installing Yosemite

After installing Yosemite my printer will not connect because it is not "found" by my macbook pro. I re-installed the driver, but that hasn't worked. What else can I do? I've restarted, unplugged . . . all the obvious things haven't been successful.

Hi Bella,
This video helped me Printer/Scanner Fix With Yosemite No Matter What Brand. another thing you might want to do if that doesn't work is to add your printer by IP adress
-crazy

Thunderbolt bridge ethernet connection will not work with ATT router/modem

I am trying to connect to my ATT Uverse router with a Thunderbolt adapter and it will not connect. Any suggestions?

finally works now with 10.8.2 upgrade!!!!!!!

Ipad 2 not communicating with my HP3050a printer after changing router?

Hi, hope someone can help. Recently changed broadband provider and now using a different router/network. I've set up my printer using the USB cable to a windows laptop and then enabled WiFi as directed. Now the laptop is working fine but my Ipad seems to see the printer on the network but can't communicate with it even though it is designated a shared device. Does anyone have any ideas? Many thanks

My guess is a firewall in the router. You will need admin access to the router (contact the provider). If a firewall is present, turn it off and test the printer. If it works, turn the firewall back on but weaken it a tad and test the printer again. Repeat as required.

HP Photosmart C3180 on USB Will Not Print After Update to 10.5.7

My HP Photosmart C3180 all-in-one printer (connected via USB) has worked fine up to now. Last night I installed the 10.5.7 update and now all the machine will print is a single line of text with the name of the Adobe postscript file, and then it continues to feed and output blank page after blank page without end.
I tried reinstalling my printer drivers. That did not fix it. It also keeps prompting me for an Adobe PDF file name each time I send a document to print.
I've tried printing PDFs, Word documents, web pages, etc., and I keep getting the same results.
Any suggestions about alternative drivers or are other people experiencing printer problems after the update?

I downloaded the 10.5.7 update on its own and reinstalled it. That seemed to fix the problem now. Don't use the "Check for Updates..." link in Finder.

Not printing after changing cartridges

Purchased this printer a year and half ago but just took it out of box to use it about 3 months ago And it's been nothing but trouble since. It won't print anything properly. I have aligned print heads and cleaned the print heads numerous times to no avail. Changed the cartridges also doesn't work. A message keeps popping up on the touch screen but doesn't stay long enough to read it. Something about print heads. Can anyone help please.

The post here has links to a troubleshooting document for the Photosmart 6520. If the steps there do not resolve the issue please contact HP Support, even if the printer is no longer under warranty. If the above does not give satisfactory results then please post back here after calling HP.

Can't find wireless printer after changing router

I have recently changed my router to a Virgin media superhub. This has obviously changed my network details. I had 2 wireless printers running on my old network. ?I have managed to get one working as it has a menu screen on it and it was just a matter of searching for the new network. My second printer, a HP 1102w does not have a menu just buttons. I cannot get my Mac to see it in any of the preference options

maybe the features of the usb port is controlled by the routers setup page most routers have some ip address you type into a browser and login to the router to set them up try that
because some routers have usb for external hd some for printers some only for firmware updates (like the Apple TV (which of cause are not routers but have usb connector for the sole purpose of upgrading a crashed firmware))

Computer will not boot after changing RAM.

Hi All,
I have had some BSOD since I upgraded my system earlier in the year. So yesterday I decieded to try and test if the problem was one of the RAM blocks, by only using 1 X 4 MB ram at the time, and then after a BSOD I would change it to another RAM and test again.
Anyway, I started by taking all 4 X 4 MB ram's out, and then only insert 1 in Dimm 4(first found out later that I should have put it in Dimm 1). This worked fine, and computer rebooted, and I used it all yesterday. Then just before I went to bed I got another BSOD, so I powered the computer off, and then this morning before turning on the computer, I replaced the RAM with one of the other 4 MB ram, to continue the testing of my ram blocks.
But now my computer just wont boot anymore! I tried putting all RAM blocks back, putting 2 of them in, 1 at the time, and every combination I can think off, but it just wont start anymore.
When I power on the computer, it does start the fans, and the 2 blue light in the motherboard is on, but nothing comes on the computer screens, and no beeps or anything at all. It just stands there with all the fans running without booting bios.
I tried resetting the CMos, and removing the battery like shown in your guide on here, but it made no difference. I also tried to remove ALL ram blocks, just too see if it then would give me any beeps, but exact same thing happens. So I supect that the reason it does not start booting, is because it thinks that there is no RAM in the motherboard ???
I really hope someone can help me out here, since I'm close to giving up, and I'm out of ideas. Everything worked fine last night, but after switching the RAM block, it just wont boot anymore no matter what ram I put in it.
My system is:
MB: Z68A-GD80 (B3)
CPU: Intel Core-I7 2600K
RAM: 2 X 4 MB Corsair Vengence 1600 Mhz & 2 X Kingston Hyper-X Genesis 1600 mhz
GFX: HD 4870
Monitors: 2 X Asus vW246H
Please help! thanks in advance!

Quote from: Froggy Gremlin on 31-August-12, 18:25:21
This is almost always a recipe for failure and the most likely cause of the BSOD's. Recommend to pick one kit or the other to use, or better yet if 16GB is wanted, purchase a 4X4GB kit.
Check to see if the EPS/ATX 8-pin CPU power connection is secure. The PSU is not specified in your component list. It is possible it has gone bad. Test with only one RAM stick in the primary DIMM slot. I have the most trust in the Corsair brand.
Prior to the test, remove the PSU power cord, remove the battery for awhile, clear CMOS.
Hi, thanks for your reply.
I have been running with those different ram blocks for a long time, and the 2nd set I actually got after the BSOD's started to test the ram. The BSOD is very likely to be because of a bad Win 7 installation anyway, since I cloned my old HDD to a new SSD, and that is apperantly not a good way to go, so the lets just forget about the BSOD for now - that aint my main problem right now..
I did what you surgested above, eventhough I done it before. I now have just 1 corsair ram in DIMM 1.
Removed powercord, then I cleared the CMOS again by pressing the clear cmos botton at the back with a screwdriver for 10 secs. Then I removed the battery for 10+ secs as well.
Still does not seem to boot into bios. Fans running, and light on MB, so powersupply must be fine as well. Seems unlikely that it should just die overnight anyway.. Powersuppy is a Corsair HX 750.
CPU power conector is fine. I really haven't done anything except switching that RAM block this morning. Last night when I powered the computer down, everything worked fine.
To be sure that its not because my GFX card should have gone bad overnight, I tried with another GFX card, but still nothing comes on the screens when it should be booting up.
If the none of the RAM was working, or it does not detect any ram in the motherboard, shouldn't it atleast be giving some sort of error beeps ?? What is so frustrating is, that I get NO errors or sound or anything.. I just a black screen, and a computer with atleats all fans running..

B210a will not print after changing router\modem

Similar Messages

Maybe you are looking for