B570 display fails after dual monitor display

After running my B570 (1068) with an extended display, the unit went into hibernation. On wake-up the laptop screen is indecipherable garbage. The second display will run to show BIOS startup but then reverts to the built-in screen - which is illegible. Toggling the F3 key does not get a good screen.
I read another post suggesting this is a hardware failure. What parts have failed?
Solved!
Go to Solution.

Hi Roger,
In that case, please try to turn ON any one of the display and check re-installing the driver and this is not possible. The only available is option is to contact our Technical Support for further Assistance to get the details of the nearest Authorized Service Center to get the issue analyzed.
Click here to open a link where you can select the country and get the exact contact support number. I’m sure they will be a great help.
Do post us back for further queries.
Best Regards
Shiva Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

How to use dual monitor display in windows 7 using MSTSC command.......??????

how to use dual monitor display in windows 7 using MSTSC command ....?????

Hi Anurag,
The main issue is how to use the dual monitor in the Remote Desktop Session in Windows 7 ,right ?
please refer to the following links:
Using Multiple Monitors in Remote Desktop Session
http://blogs.msdn.com/b/rds/archive/2009/07/01/using-multiple-monitors-in-remote-desktop-session.aspx
Best regards

Dual Monitor display/firmware difference

I purchased a Pavilion 27xi monitor from the HP Shopping site in October 2014 and purchased an additional 27xi to be used in a dual monitor setup. I received the new monitor this week. The newer monitor does not match the color/white of my existing monitor. When I move a white rectangle so it displays on each monitor, on the new monitor it appears as greenish gray instead of the white of the older monitor. I have done the factory resets, switched display adapter outputs (NVIDIA GeForce 9800 GT), tried one monitor at a time on either adapter output. All with no change in the behavior of the new monitor. The internal setup/control menus of the monitors differ in content and style/color.
Older monitor info: manuf: April 2014, Rev: RIM111
New monitor info: manuf: Dec 2014, Rev: RIM232
I have talked with HP "support" and one person thought it was because of the revision level difference.
I want the display quality of the older monitor, Rev: RIM111. If the monitor difference is because of the revision level, can the newer monitor be put at the RIM111 level. I tried to purchase a monitor with the RIM111 level and was told by HP Shopping that they do not have any at that level. I this a firm level that can be changed? If so how do I accomplish that?

Hello @tomas44,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that the newest monitor you have connected to your desktop computer does not match the color/white of the existing display, and I would be happy to assist you in this matter!
To ensure that your system is properly configured for dual monitor displays, I recommend following the steps in this document on Using Two or More Monitors with One Computer (Windows 8). If everything is setup accordingly, I recommend following the steps below for the newest monitor:
Step 1. Unplug the power cord from the back of the monitor and the wall
Step 2. Hold the power button down for at least one minute
Step 3. Plug the power cord back into the monitor and then into the wall outlet (not a power bar or surge protector)
Step 4. Press the Menu button on the monitor
Step 5. Navigate to the Factory Reset option and select it
Step 6. Try a different cable connecting your monitor to your computer
If the above steps did not resolve your issue you can try the monitor on a computer or other device to see if the issue persists. Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Thank you for posting on the HP Forums. Have a great day!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Dell Optiplex 780 standard size tower PC dual monitor display port graphic cards

Yes, only my boss informed me that they have to be display ports, he didn't tell me why.
I'm unable to buy from ebay or craiglist either & my local vendor doesn't have any in stock.

Quite a mouthful I know! but I need these specific graphic cards, ideally with next day delivery:
Dell Optiplex 780 standard size tower PC (Non SFF) dual monitor display port graphic cards
Any recommendations? I can find 2 on amazon (UK) I need 3!
This topic first appeared in the Spiceworks Community

IMac Display failing after 1 year of average use.

I have a mid 2011 27" iMac (the one with thunderbolt) and the display is starting to fail after 1 year of average use (an hour of use every day on average). The display is now much dimmer on the left half of the display (the GPU sits underneath that portion) and also flickers the whole display now and then to a lower brightness.
I am about 45 days out of warranty and basically will have to cough up $500 to have it fixed by Apple. My questions are... Has anyone else ever had this happen to them? The genius bar employee thought that it was something he has seen happen to displays when exposed to heat over long periods of time. So basically playing starcraft 2 and doing video encoding killed my display if you believe that to be the cause.
Are there any conditions in which apple would recognize this as a manufacturing defect and fix it free of charge? Otherwise it looks like im writing a check for $500 next week.

Today a dark streak showed up on my display right in the middle. It is shaped like a zebra stripe but is dark grey and wont go away.
I too have a mid 2011 27" 3.4GHz i7 iMac with a 2GB Graphics card . Im about 50 days out of warranty.
Seems like its perfect coincidence for apple that 50 days after my warranty runs out, the most expensive thing to repair breaks.
After doing some research it seems like there is a lot of people with this model experiencing this problem.
Pretty sad that my 2005 iMac is holding up better than my brand new iMac.
Been saving up for it for like 4 years and I dont have the money to repair it.
I tried everything, I knew none of the stuff i tried would work but i still tried resetting the PRAM repairing disk permissions all that good stuff. I even have an air purifer/dehumidifier in my room so i dont know what caused it.
I didnt think i needed applcare because ive had my other imac since 2005 without a hiccup.
Ive rendered out 3d animations using the cpu at 100% for days and it still runs fine.
Havent even used my new imac for anything that would put stress on it.
What i do notice is that it runs hot all the time. ever since I got it. Sometimes just doing basic stuff such as browsing safari it can get so hot where i cant touch it. my GPU normally stays at around 70C and the hottest its been was 80C which is still safe. The alluminum is supposed to transfer heat better but all it does is retain heat more and get super hot. the old plastic one i have is 10x cooler.
What i did notice today tho when my screen problem happened, is that the GPU temperatue is at 50C and wont go above it. I monitor the temperature with istat and never have seen it at 50C and below unless i am just doing a fresh boot.
What really concerns me tho is how the screen went out so close to when my warranty expired.

Windows: Stretched display and no dual monitor

Hello. I have a mac book pro with 2 gigs ram and an ATI mobility radeon 1600 graphics card. Everything works perfectly when in OSX nd the dual monitor works perfectly. I have an old NEC monitor I pluged in to my macbook using the display adapter that came with the notebook.
How ever. when booting up windows XP, during the loading, both monitors work, but when windows actually starts, my external monitor stops working, and everything is stretched horizontally on my notebook display.
I have had no luck updating ATI drivers as they say I am not supported or something. And apple care directed me here. Any help would be greatly appreciated.
Thank you for you time.

I am trying to use an Epson projector as my second monitor and am unable to find that tab you mentioned. Can you please post where you found the tab you clicked on to make things work for you?
MacBook Pro Mac OS X (10.4.10)

How do I display wallpaper across dual monitors?

I have an iMac 21.5 Mid 2011 and my second monitor is a SAMSUNG SyncMaster SA350. My iMac displays the amazing Apple Lion background and the samsung monitor displays the default Apple Galaxy background. How do I stretch across both? I thought maybe I needed a panoramic background, but it didn't move over. Any suggestions? Thanks!
Brian

Here's how I do it:
1. Download application called "Multiscape", click "Softpedia Secure Download (US)" and it will automatically start downloading
2. Get the wallpaper suitable for your dual screen.
3. Open "Multiscape"
4. Drag wallpaper file into the Multiscape and it will automatically display onto the screens.
Hope this helps.

Display sleep with dual monitor setup

I'm running a 17" studio display and a 20" studio display as a two momitor setup on a dual G5 2.0. The menu bar is on the 17". Unless I have display sleep in energy saver set to never, the 17" will go to sleep at the interval set in the preference panel, even when the system is in use. So far the only way I've found to get the display back off sleep is to put the computer itself to sleep - keyboard shortcut or by using the power button on the 17" and then wake it up.
I think this only started with 10.4.6. I can't upgrade to 10.4.7 yet - I run Avid Xpress Pro on the system and 10.4.7 gives dongle trouble. I've thrown away preference files, set and reset the sleep parameters. As it happens, I've had to reinstall the system a couple of weeks back, but the 17" studio still goes to sleep when it shouldn't.
The problem doesn't occur if the menu bar is on the 20" cinema display, but that's not the way I want it.
Anyone with the same problem,, or better a suggested solution?

finally found the solution (apple i hope your reading
this as this is a mad bug!)
you need to have the dock on the bottom of the main
screen in order to view the image on that screen.
Wierd, I have my dock on the left side of my main screen... which is to the left of my secondary screen. Perhaps you cannot have the dock in-between screens?
kgelner, how have you noticed the performance of your
card when working with aperture? Im seriously
debating upgrading mine as its just slow and annoying
I find it usable but I'm also only working with TIFF files (my camera is not supported). I am also pretty strongly thinking about going with the X800xt card, which should be at least twice as fast. Some operations (like a lot of Spot & Patch repairs combined with Shadows/Highlights) do make things a bit laggy.
I also have the 256MB version of the 9800, which I think helps with some of the larger images and operations.

W530 Dual monitor display

Is it possible to set the graphics card for the laptop display to use the nvidia Quadro instead of the Intel integrated chip?
Right, now the resolution for the laptop screen is at 1920x1080
and the resolution for the external monitor is 1600x900 (native)
The external monitor display is fine, but the laptop display is shrunken and there are huge black bars on all four sides.
Solved!
Go to Solution.

Jyang772 wrote:
Is it possible to set the graphics card for the laptop display to use the nvidia Quadro instead of the Intel integrated chip?
BIOS setup -> config -> Display -> Graphics device -> discrete graphics.
And I also set "OS detection for nVidia Optimus" to DISABLE (from default of ENABLE).
Link to picture
This guarantees using only Quadro graphics, for both internal laptop screen (if you want to use it) and external monitor (if connected).
If you really want to use BOTH laptop LCD screen as well as external monitor (simultaneously, in "extended desktop mode") then in nVidia Control Panel you must activate both monitors in the "set up multiple displays" dialog.
Link to picture
I have my external 1920x1200 monitor connected using the DP connector from my K1000M on my W530, and the laptop screen is 1920x1080. As you can see from the above, each screen is independent and can be set at whatever resolution you want ("native" or otherwise). I have no black bars anywhere when both monitors are enabled and active. Each monitor runs full-screen in its own unique "native" resolution (set through nVidia Control Panel's "change resolution" dialog), as the above graphic implies and as we want.
And of course, you also need to have Windows desktop display properties (right-click on desktop, select "screen resolution") configured for "extend mode".
I do not use the VGA connector. I use the DP connector, and "discrete graphics" in the BIOS, with "nVidia Optimus" disabled in the BIOS. I'm also running native nVidia 332.50 retail drivers, downloaded from nVidia site (not Lenovo Optimus driver).
NOTE: I normally do NOT run with both external monitor and lapsop LCD screen both enabled, in "extended desktop" mode. Instead I only have ONE monitor enabled with nVidia Control Panel. I see no point in using a tiny 15" laptop screen at 1920x1080 along with a 24" external monitor at 1920x1200. One or the other is fine, depending on the situation.
Then, in this single monitor mode, if the external monitor is connected and powered on Windows comes up using the external monitor (and not the laptop screen) at its native 1920x1200. If the external monitor is disconnected or powered off, Windows comes up using just the laptop screen at its native 1920x1080.
No internal Intel HD graphics used at all. This is all using nVidia K1000M exclusively with external monitor connected via DP connector, one monitor or two (in extended desktop mode or even "clone/duplicate" mode if I wanted).
For me this is perfect.
Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules

Both the screen flickering after dual monitor setup in Premiere Pro CS6

Hello,
I recently installed Premiere Pro CS6 in my PC. Then after I set up dual monitor in the Preference, the screens of both the monitor started to flicker until I stop the playback. Previously I used same hardware with CS5 but there were no problem.
Link to dxdiag text file :
https://dl.dropbox.com/u/53681371/DxDiag.txt
I have attached the screenshots of msinfo32 and my graphics drive info.

Some ideas for a Desktop Video Editing PC
http://www.adkvideoediting.com/
-ADK Kudos http://forums.adobe.com/thread/877201
Build http://forums.adobe.com/thread/878520?tstart=0
-more build ideas http://ppbm6.com/Planning.html
-Build it Yourself http://forums.adobe.com/thread/815798
-http://www.shawnlam.ca/2012/premiere-pro-cs6-video-editing-computer-build/
Laptop Video Editing PC http://forums.adobe.com/message/4578948

2nd External Display Failing After Yosemite Upgrade

I have a late 2009 iMac 27 (3.06) that ran perfectly fine with TWO external displays (both HP Pavilon 27 xi's). Upgraded yesterday to Yosemite and now 3rd monitor (2nd external) fails to find a source feed. Any advice out there? (#1 external monitor is connected via direct mini DVI to HDMI via a Rocketfish adapter; works perfect; 2nd external monitor is connected via a USB to CableMatters HDMI to DVI adapter to back of HP monitor - worked perfectly for months until last nite; (HDMI to HDMI never worked). Advice? Thanks.

I have used an Acer S230Hl on three Makbook Pros via the VGA wire and a thunderbolt adapter. No problems at all with 10.6, 10.7. Worked perfectly.
With 10.8 the display would not wake up from sleep, most of the time. I found an annoying work around that helped maybe 70-80% of the time: unplug the VGA+adapter monitor feed, and then go to system preferences>>displays>>Color>>open the S230HL profile and then simply plug the monitor back in. I also delayed the sleep feature for 2 hours to prevent the problem, but it happens most of the tiem when I close the lid or put the machine to sleep manually.
Now with Maverick (10.9), even this elaborate this trick does not work. Why the loss in compatability Apple? I've called applecare twice and the techs have not been able to help--and now are not responding or calling me back. Having to reboot my mac 3-4x a day is a major problem. Anyone have ideas for me?

Macbook Pro late 2011 with Thounderbolt, will it support dual monitors display?

I have recently working on this Macbook pro, and wasn't able to find accurate information about the dual display solution for this MACBOOKPRO model.
It has thunderbold port.
Have anyone happen to have this model and successfully connected with two conventional monitors?
Conventional monitors I mean, VGA, HDMI, or DVI.
Thank you.

Hi O,
According to MacTracker, the answer is a clear no for the 13" and yes for the 15" and 17".

Dual Monitor displays weird colors

Hi there,
Yesterday I bought a Displayport to HDMI adapter (Mini DisplayPort Male - HDMI female) for my MacBook Pro 15" (Late 2011 version). I use this to connect my MacBook Pro to my Philips 32" television. Everything has been set up (I've adjusted the resolution of the TV to 1080p and put my refresh rate to 50 hz since my TV doesn't support 60 hz). But once in every 5 - 15 minutes or so, my screen turns green for a brief second and suddenly my background or whatever is on my second monitor turns in to weird colors. Sometimes it takes about 2 or 3 seconds and it switches back to how it normally was, but sometimes it takes way longer. I don't mirror my screen, I use it as a second display. But I can't figure out why the screen it switching betweens there colors and don't know how to fix it. I've looked it up on the internet, but couldn't find anything useful. So I hope you guys could help me with this.
Thanks in advance.

Oops, I see that I'm in the wrong forum. Sorry about that.

DUAL MONITOR DISPLAYS

Anyone know of a way to keep the second monitor active when an application on my iMac screen is set to use "Full screen" mode. I can be anything from a game application to Aperture or even YouTube videos; any full screen mode seems to do it.
I bought the Apple brand Mini DVI to DVI adapter to connect the second display.
Thanks in advance for the help!

It's up to the application as to what happens to the second display when full-svreen is used.
For example, MPlayer OSX Extended can be set to run in full-screen mode and leave the second display useable while watching movies or DVDs.
<http://mplayerosx.sttz.ch/>

Seamless Windows and Dual Monitor Display

Seamless windows open spanning both display monitors regardless of the settings I use to prevent it. It's like the SGD thinks both monitors are one big display and doesn't open things in just the default monitor. An application that opens maximized will cover both monitors!
Has anyone else had this problem and found a workaround? We are using Windows XP client (Dell laptop), IE6, 2 display monitors (NVidia graphics card), and the application server is Windows 2003, SGD is 4.2.

It is an individual application we are publishing in the seamless window, but that one application launches many applications from there -- it is basically a toolbar for launching a whole host of other applications.

B570 display fails after dual monitor display

Similar Messages

Maybe you are looking for