Back board sound problems with speakers (front jack fine)

hello
i recently upgraded my system to the p7n sli platinum
weird problem has occured
The front out jack works fine both with headphones plugged or with speakers
but rear green jack doesnt work with either speakers or headphones plugged in
moreover, frontjack puts out only left channel in both speakers and no right channel at all
does anyone have a solution?

re update
I found the little check mark that enables to hear both front and rear audio.. so that is set
only problem left is stereo sound.  when i click right audio output i get no sound, when i click the left audio output i get sound in both sides.. anyone?

Similar Messages

  • Greetings Community:  I have a problem with my headphone jack: no sound.  The problem is not with the headphones... the jack just does not transmit any sound... any ideas how to fix this?  It seems to be a rather strange problem.  Thanks for your help.

    Any ideas on how to fix a problem with a headphone jack on my
    desktop power Mac (mid 2007).  I don't have a clue on this one.
    Paul

    Hi Paul,
    ...on my desktop power Mac (mid 2007)
    Are you sure you don't have a Mac Pro? The last of the PowerMac desktops were discontinued in August 2006.
    What does "About this Mac" (in the Apple menu) say about the processor type?

  • Sound works with speakers but not without.

    The sound suddenly went off earlier today,can hear when plugged into speakers or head phones only?

    Try the following to rule out a software probleM
    - Reset. Nothing will be lost.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup
    - Restore to factory defaults/new iPodIf you still have the problem you likely have a problem with the headphone jack in the iPod.  They can be replaced.  I would make an appointment at the Genius Bar of an Apple store to identify/determine the cause.

  • Sound problems with my Visio

    Hi, I have read that people are having sound problems with their Vision M players, hissing etc.
    I wonder if anyone has had the problem I have - I cannot alter the volume! When I plug in either headphones or portable speakers into the M, using the touch pad has no effect on the volume. If I unplug it the touch pad then alters (or appears to) the volume - judging by the scale on the right of the screen. Plug the phones back in again and I get the same one level of volume.
    Also, the screen goes blank when I plug in phones or speakers.
    I am an MP3 player virgin and have no idea if the fault is mine or not.
    I bought my Vision M from Amazon, who very quickly sent me a replacement when I contacted them - even before I had returned the original. But the replacement has the same problems.
    Any comments would be welcome.
    John

    woggydog, thats what happens when your plugging outputs into the Audio/Video out socket of the player using the dock or supplied connector... it goes into line Out Mode, which cuts out audio from changing since the amplifier would be able to control this on a sound system.
    The one that shouldn't do this is the one on the top right of the player.

  • My ipod touch is having problems with the headphone jack when I rotate a little song stops

    my ipod touch is having problems with the headphone jack when I rotate a little song stops

    Hey Silverdemon, sounds like a short, most likely in the headphones. Try a different set of headphones with this iPod or try the headphones with a different device. If the problem stops with your iPod or it moves to another device, then replace the headphones. If within 1 year of date of purchase Apple will replace the headphones for  free if problem is a defect, not abuse. If the problem continues with a different set of headphones, check the port for damage and foreign debris. If you note debris, attempt to remove it, if damage noted contact Apple and set up an appointment to have it evaluated. if nothing appears wrong, try plugging / unplugging to jack about 12 times maybe corrosion on the contacts if so that should clean it. Next thing to try reset your iPod. After that try restore from backup. Last resort, restore to new. Just make sure you make a full backup to your computer before you restore so no data is lost. If nothing works, contact Apple and set up an appointment to have your iPod evaluated. Good luck, Cheers.

  • Audio has ceased when at Amazon and with e-mails with audio attachments. This only during last few days previously O.K. Windows Media Player still working so no problem with speakers only happens with online audio. John

    Operating system Windows 7. A few days ago no problems with audio, clear sound when listening to e-mail audio attachments and Amazon music samplers. During last 2/3 days both attachments and samplers fail to work, but when playing music from library held in Windows Media Player no problems. This would appear to show no problem with speakers etc and I have not knowingly amended any audio controls.

    Thank you so much for replying.
    Yes I have removed and reinstalled WMP.
    I had good results with the PD6 application installed on the default path onto the C: drive with the one exception that if the application was launched by accident and the user data path was not available, the PD6 application would blow away my custom user path registry settings. Now that I know what they are I have made a .reg file to repair my registry to my desired user data paths.
    Installing the application on the removable drive appeared to help prevent me from launching the application by accident and overwriting my registry with default user paths.
    So which is the less of the two evils?
    If the application directory is not available, windows media player still tries to launch the .msi for installing PD6.
    If I install the application to the C: drive but the user data to the removable drive, launching the PD6 application without the user data drive will still corrupt my registry settings for a user data path.
    Both these issues seem like a logical (if not easy) fix that should be done in the PD6 application and installation package. I mean really, cannot anyone tell me why windows media player is checking the PD6 application directory? Why in PD4 did we have an option control for setting the user data path from the PD4 application? Why is this option not in the PD6 application, just the installer?
    I am given a choice during installation to move the user data to another non default location. Why else would this be provided if not to accommodate my kind of request to store the user data into an alternate location other than “My Document”. Certainly Palm is not trying to force the users on how to protect and store their personal data?
    Post relates to: Centro (Verizon)

  • Problems with the front camera on iPhone 4

    Hey, guys. Just faced a problem with the front camera on my iPhone 4. So, when it's enabled this thing is on screen and all the pictures taken on it also has it:
    http://bit.ly/epZypp
    I've never dropped the phone, it isn't jailbroken or unlocked, it was bought in Britain but using in Russia, the firmware is 4.2.1.
    So, guys, can you help me?

    Have you tried resetting your phone by holding down the sleep/wake button and the home button at the same time until the phone restarts?

  • I have sounds problems with iOS 7

    I have sounds problems with iOS 7. I can not hear my music, all the apps have no sounds. Only when I ask Siri has sound but it's too loud and awful. I found 2 errors with I ask to Siri what things she can do in Spanish the is an error and one word or If I ask who am I? She said that I have to go to settings and indicate her who I am but I already have that configured. And I try to configure again just in case, I do the same question and she still doesn't who I am.

    Try a Restart. 
    Press and hold the Sleep/Wake button for a few seconds until the red "slide to power off" slider appears, and then slide the slider. Press and hold the Sleep/Wake button until the Apple logo appears.
     Resetting your settings
    You can also try resetting all settings. Settings>General>Reset>Reset All Settings. You will have to enter all of your device settings again.... All of the settings in the settings app will have to be re-entered. You won't lose any data, but it takes time to enter all of the settings again.
    Resetting your device
    Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears. Apple recommends this only if you are unable to restart it.
    Or if this doesn't work and nobody else on the blog doesn't have a better idea you can contact Apple. 
    Here is a link to their contacts with most of the information below. 
    http://www.apple.com/contact/

  • Is there a fix yet for the no sound problem with lion on the iMac without having to restart every time I switch the computer on?

    Is there a fix yet for the no sound problem with lion on the iMac without having to restart every time I switch the computer on?

    Try booting in Safe Mode by holding the the shift key immediately after powering on your system. Safe boot mode will for a directory check of your startup volume, then load only the required kernal extensions (kext files), and deletes some cache files. Once the system boots into Safe Mode you can simply restart the system to see whether the issue has been resolved.
    If you still have the issue try resetting the SMC by shutting down the system and disconnecting the power cord for ~15 seconds, then reconnecting the power cord. Next, reset the parameter RAM (PRAM) by holding down the option-option-P-R keys after powering ON the system. Wait until the iMac restarts twice, then let the system boot normally.

  • Really weird sound problem with rhythmbox[SOLVED]

    Well, I can't find anything on this, so i'm posting it here. I have no sound problems with alsa or other gstreamer apps(totem, banshee plays sound just fine). But when I try to play something in rhythmbox it just does not work. Mostly there is no sound, but every couple of seconds you can hear a distorted sound that is suposed to be playing for a moment. Rhythmbox does not issue any warnings or errors when launched from terminal. Is this some kind of bug?
    Last edited by klohs (2009-05-15 13:34:46)

    I had the same problem, but it disappeared yesterday. Try it run under root - it helped me. I dont really know how i fixed it, but it works under normal user now as well ...I hope there will be someone who knows.

  • Sound problems with iPhone 6 plus

    I have sound problem with my iPhone 6 plus.
    Some apps have sound, others no.
    For exemple the app minipiano has no sound (it works fine on my ipad mini)
    Does anyone has the same problem ?

    Hello there,  .applefan.
    When having performance issues with an application installed on your iOS device, the following Knowledge Base article offers up some practical steps for troubleshooting your issue:
    iOS: An app you installed unexpectedly quits, stops responding, or won’t open - Apple Support
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Sound problems with movie

    I just purchased the movie "Overboard" in HD. The movie video plays ok, but the sound keeps going in and out.
    I don't understand why this is happening. My music plays ok and I'm not having any other sound problems with my
    computer.  I am running Itunes on a Windows 8.1 desktop computer (Gateway).
    I couldn't figure out how to re-download it or repair it.
    If anyone can help, I'd appreciate it!
    Thanks!

    Hi Larry James,
    If you are having video playback issues in iTunes on your Windows machine, you may find the following articles helpful:
    Apple Support: Troubleshooting iTunes for Windows Vista or Windows 7 video playback performance issues
    http://support.apple.com/kb/ts1718
    Apple Support: Downloading past purchases from the iTunes Store, App Store, and iBooks Store
    http://support.apple.com/kb/ht2519
    Regards,
    - Brenden

  • Sound problems with Portege M600 using WXP SP3

    I have had on-going sound problems with my laptop and feel so frustrated - please help!
    I have downloaded the sound driver (abt a million times - and tried uninstalling then reinstalling) - and repeatedly get no volume icon on the desk top and a message saying "no sound driver can be found".
    I did manage to fix it once - when i had WIndows Vista installed - by finding some obscure patch - but this time around - no solutions.
    Can anyone help - it is so frustrating!!!!

    The mentioned patches are part of Win XP SP2 & SP3
    So ensure that all service packs are installed.
    Then go to device manager and delete the High Definition Audio Controller (in system devices) and additionally delete all devices from Audio, Video and Game controller section.
    Then reboot the notebook.
    Wait until the device would be recognized again and then install the sound driver!

  • Sound problems with Satellite A100 (PSAA8)

    I am continually having sound problems with the laptop. Whilst I hear the windows start up noise and beeps, I cannot hear any sound from things like CDs, iTunes, Media Player - in fact an error message will always come up. In Media Player the error message "Windows Media Player cannot play the file because there is a problem with your sound device......." comes up. I have a the standard pre-installed Realtek sound thing on my laptop. I have tried downloading a newer driver from the Toshiba support centre, but I don't know what to do with the zip file. Also in Control Panel, Sounds, everything is greyed-out.
    Hope someone can help cos I am going nuts with this :-)
    Thanks

    Hi again
    I have downloaded the Realtek sound driver from the Tosh page and unzipped it.
    (I have chosen the driver for Vista!!! I suppose you use Vista???)
    There is a folder called sound. Access this folder and run Setup.exe
    But before you will start this procedure you could access the device manager (control panel -> computer -> device manager) and choose sound, video, and game controller. There you have to mark realtek AC and click on uninstall and reboot the unit.
    After this sound driver removing you should start the new driver installation described above. (setup.exe)

  • Sound problems with my apple products

    I have been having sound problems with my apple products. I updated they and it went away for a little while but now my ipad  has no sound and the volume controls will not show up

    Hello Jamie_245,
    While the article was written for the iPhone, the troubleshooting details can be useful for resolving similar issues with an iPad.
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/TS5180
    Cheers,
    Allen

Maybe you are looking for

  • How can two pictures of the same size still appear to be a different size? (Photoshop CS6 problem)

    I called the big webdesign file "(X)" and the image I wanted to paste in it "(Y)", so that you won't be confused when you read it. What Happened For the design of a webpage, I made a photoshop-file(X) with a lot of squares(X). These squares(X) had th

  • CD/DVD drive not working properly

    Hello, I have a Satellite L305-S5907. I just received it Dec. 2008. Recently I installed a game. Stronghold 2 and had trouble with disk 2. I managed to get it installed. When I would put in the play disc it would not always recognize it so I uninstal

  • Descriptor-app doesn't work in Flash CS5.5

    Hello, In Flash Pro CS5.5, when I publish my air app (air, air android, air iphone) a tag <version> reappears  so I'm in AIR 2.6 !!! Furthermore, the problem appears in Mac not in Windows ?! Why?? Someone have the same problem??

  • BDC works in A-mode but not in N-mode.  Why?

    We recently upgraded from 4.6b to ERP6.  I have a BDC that fails in ERP6 so I am trying to rework it.  Something odd is happening.  I find that some BDCs run through find in A-mode while you're stepping through them but not in N-mode when it's hands-

  • Scroll is using a lot of CPU

    Hello In my application I have a general scroll that contains a lot of tables and tabs. The scroll is working slow and is using a lot of CPU power. Table scrolls are working fine. Could be something wrong in the code? Thank you