Back to my mac doesn't work since I change from me to iCloud

This feature always worked well in my macbook and my iMac. Since I updated my me account to icloud account I always have the same problem with "back to my mac" the message is I should have a problem with my router with uPnP or NAT-PMP. I have checked all the parameters in my router and finally I think is a problem with icloud.
I don't know if I am the only one with this problem. Why back to my mac worked fine with me account and now with icloud it is not possible?
Any help will be appreciate.
Thanks

Thank for your help.
Finally I could solve the problem. From my point of view is a problem inside the service apple provides with icloud because it didn't happend with me.
So the solution was in my router, in my router there is an option in NAT about DMZ enable with a host address. DMZ means:
"If the demilitarized zone (DMZ) is enabled, the packets that are sent from the WAN and that cannot match any rule are sent to the computer on the LAN side for analysis or other uses, before the packets are discarded by the firewall."
So I enabled this option and I used as a host address my home iMac. After this, I can confirm from my office that back to my mac worked as espected.
regards

Similar Messages

Back to my mac doesn't work with Cable modem

I have at home Cable modem and a Airport Extreme, both use NAT to distribute internet, so it seems even if I connect the cable modem direct to my home Mac (without the Airport) that the Back to my mac doesn't work. Can somebody tell me how can I turn around this problem? Doesn anybody has it too?
The Back to my Mac panel displays this message when I have the Airport Extreme distribuiting the Internet: Back to My Mac isn't working properly because you may have more than one device on your network providing Network Address Translation (NAT). Try disabling NAT on one the devices.
And without the Aiport: Back to My Mac isn't working properly because it requieres a router that supports NAT Port Mapping Protocol (NAT-PMP) or Universal Plug and Play (UPnP). Make sure your router supports one of these protocols and that it is enabled.

If I may continue this thread, I have the same double NAT issue and am using a DSL modem/router combo. I added an Airport Extreme to my Qwest supplied Actiontec dsl Modem/Router in hopes it would solve issues with Back to my Mac, among other things. The dsl modem supports UPnP to some degree, but BtmM doesn't seem to like it.
Currently the setup uses the DSL modem/router first in line, functioning as modem, NAT, router, but no DHCP (or wifi). That plugs into the WAN port of the Airport BaseSta. The Base Station runs in bridge mode, and distributes the ethernet and wifi connections. I would rather bridge the modem and disable its router functions, and let the Airport handle NAT and routing and wifi and Back-To-My-Mac.
What are the alternatives? Any help appreciated!

Back to My Mac Doesn't Work

Has anyone figured out how to make "Back to My Mac" work? I have 2 Macs running Leopard and a .Mac account, but do not even see a "Sharing" category in Finder, so it does not seem to work.
Are there any directions or suggestions as to how to make this work? There is a video on the website, but it has a "Sharing" category that my Macs are missing.
Thanks.

Greetings Mac World,
I stand corrected...finally. Three things.
1. My desktop, iMac G5, malfunctioned and was out of commission until repaired by an Apple tech today, so I hadn't been commenting on the whole Back To My Mac issue. But now that it is repaired (bad power supply on iMac G5), I can add an additional two cents.
2. My iMac G5 did not have 10.5.1. According to the updates I downloaded this afternoon using Software Update, I still had to install 10.5.1 on my G5. Odd I thought, since I was almost 100% certain it was already installed. But the updates included 10.5.1, so it was applied (or re-applied in my mind) tonight.
3. I reset my base station to the default settings on Airport Extreme and did the automated setup again to reapply security to it (WPA2), but left all other settings alone.
Voila...Presto...Hocus Pocus and....Drumroll please
Back To My Mac works instantly.
So I guess that rules out the theory on having a dot in your user name, since I have 3 dots. And sort of validates the whole 10.5.1 solving Back To My Mac. Granted I'm basically using all Apple products, but...
Hopefully, this sheds light for someone else.

I can not get my regular mail to work since I changed to moved to iCloud. What do I need to do?

I can not get my regular mail to work since i moved to iCloud. What do I need to do to update?

Go to Settings>Wi-Fi. At the bottom, make sure the "Ask to Join Networks" is ON. When you are out and about, any network the iPad sees will be shown and it will ask you if you want to "Join" it. If it is unsecure/free you tell it yes and you should connect. However, if there is a little padlock looking icon shown with the network name, it means that it is a secure network and you need a password to join. If you don't know it, you can't join. At most Starbucks and such, the Wi-Fi is free and you should be able to simply connect. Not really that hard. There are not security settings on your iPad to adjust. You'll figure it out.
Best.

Mac Powerbook with HP 5510 printer. Scanner doesn't work since I installed Lion

Mac Powerbook with Lion. Scanner doesn't work since I installed Lion

What kind of computer is it? Powerbooks can't run Lion. MacBook perhaps?
With Lion, all scanning is performed through Preview. Use Preview.

TS1398 The wifi on my iPod doesn't work since upgrading the software to ios 6 therefore when I try to reset to the original settings I can't get my original software back. Can anyone help me with this?

The wifi on my iPod doesn't work since upgrading the software to ios 6 therefore when I try to reset to the original settings I can't get my original software back. Can anyone help me with this?

greeneygreeney wrote:
so you can't ever restore it to the factory settings? that is a big shame.
"It will ALWAYS restore to the lates available software.
You cannot downgrade."

Back to my mac no longer works after upgrading to Lion

Back to my Mac no longer works after upgrading to Lion
After I upgraded my home machines to Lion, I can no longer access them from my work computer, which is running Snow Leopard. When they were both Snow leopard, it worked fine. How can I get them working again? I don't have control over the OS on my work computer. Is it necessary for me to downgrade all of my home computers to Snow leopard in order to get them talking again?
Additionally the binoculars icon appears in the menu bar all of the time. In previous versions, this would only happen when somebody connected to my machine. Could these problems be related?

OK, so further investigation has addressed the BTMM issue on a remote machine.
With all machines running lion, I was having issues trying to log in to a standard user headless machine already running. In Snow Leopard, I had no issues with this since you can log in via screen sharing using an admin login that's running a standard login. Lion allows multiple accounts to be signed in which is handy since you can now run virtual sessions. This means you can admin the remote computer without bothering the remote user.
The problem was that now logging in using admin login brings up the admin account (which makes sense) instead of the desktop to the standard login. I applied a similar solution to a problem that was related to screen sharing I found on this board. What I believe to be the fix is to add the standard user to the screen sharing user list. Then screen share to the remote account using the standard user credentials.
So on the remote computer, in System Settings->Sharing->Screen Sharing, add the standard user to be allowed access. Previously I only had admins. This may not be an ideal solution for what I'm trying to do since the remote computers primary login is the standard user to be used as a common computer, but it now works so I am happy with it.
Now my only "problem" is my AEBS complaining about my MobileMe credentials, but it doesn't appear to have an impact on BTMM performance so I'll quietly wait for a fix down the road.

Photo booth doesn't work since lion installed

what's up. photo booth doesn't work since i dowloaded lion. Help

aquaman wrote:
My mac IS up to date.
No reason it should have stopped working. Maybe a problem waiting to happen and an upgrade pushed it over the edge. Provide some specs on your Mac, but I would really advise making an appointment at the Genius Bar at your local Apple Store.
Good Luck
Pete

Problem to detect Wifi networks. I restored without back up and it doesn't work. suggestions?

Problem to detect Wifi networks. I restored without back up and it doesn't work. suggestions?

I detected one time networks with the trick (air plane mode on, power off, sim card out, power on, sim card in, air plane mode off...). since nothing. I think it's a software problem. suggestions ?

WP Greek Century in Mac doesn't work with Dreamweaver

I am a many year PC user and have finally made the leap too Mac and its another learning curve .. That said, in Dreamweaver and in Mac, WP Greek Century does not work! I have reloaded the font and all I see is the alpha #.   If I load it into any browser, it still will not read greek. My old PC didn't have a problem with this. Some of the download sites say that this font, WP Greek Century, works with both PC and Mac. The one odd spin to all this is that this greek font works in Fireworks ... Is there anything I can do to make it work in Dreamweaver? Please advise and thanks. Mark
ps. I called Apple support and they could not help.

Thanks for your reply and I was afraid that this might the answer. Looks
like I'm going to have to go back and fix a bunch of documents. Appreciate
your help in this matter. Mark
From:   SnakEyez02 <[email protected]>
To:     Marcusb B <[email protected]>
Date:   02/13/2012 09:20 PM
Subject:        WP Greek Century in Mac doesn't work with
Dreamweaver
Re: WP Greek Century in Mac doesn't work with Dreamweaver
created by SnakEyez02 in Dreamweaver - View the full discussion
Fonts don't work on the web like they do in print. Any font you use on a
website will require that the end user have that same font installed on
their system.
I did try to load that font from a free source (assuming this is how you
got it). It is a PC TrueType and doesn't appear to work at all on the
Mac. Now if you are looking for just a few characters you can code this
into the HTML:
http://tlt.its.psu.edu/suggestions/international/bylanguage/greekchart
.html . As far as other fonts, this greek font seems to work on Mac:
http://www.dafont.com/ancient-geek.font . But again, it's not a web-font
so you won't be legally allowed to use it on web pages, and it will only
work if the end user has that font installed on their system, unlike the
HTML entities previously linked.
Replies to this message go to everyone subscribed to this thread, not
directly to the person who posted the message. To post a reply, either
reply to this email or visit the message page: [
http://forums.adobe.com/message/4205108#4205108]
To unsubscribe from this thread, please visit the message page at [
http://forums.adobe.com/message/4205108#4205108]. In the Actions box on
the right, click the Stop Email Notifications link.
Start a new discussion in Dreamweaver by email or at Adobe Forums
For more information about maintaining your forum email notifications
please go to http://forums.adobe.com/message/2936746#2936746.

"Back to my Mac isn't working properly because your DNS server isn't responding. Contact your ISP for an alternate DNS server address, and enter it in Network Preferences".

Hi, i am trying to setup back to my mac at home but I get the error "Back to my Mac isn't working properly because your DNS server isn't responding. Contact your ISP for an alternate DNS server address, and enter it in Network Preferences".
There is no documentation on how to solve this anywhere.
I have an Arris router set to bridged mode which is connected to a 5th generation airport extreme. I have tried using the google dns servers instead of the one assigned by the cable company in the AE but I still get the same error.
Any help would be much appreciated
Kenneth

New to BTMM, I got stung today with the silly DNS problem message. Solution:
1) Flush DNS cache with:
dscacheutil -flushcache;sudo killall -HUP mDNSResponder
2)System preferences > iCloud > untick BTMM then tick it again. The warning should have disappeared.
Edit #1
Apologies for the noise. The warning has come back
Edit #2
Just found out that BTMM is not compatible with double NAT. That's not helpful.
http://support.apple.com/kb/TS1208

Editting PDF documents that were created by a MAC doesn't work because of font incompatability. How can we get MAC fonts and load in our Adobe Acrobat Pro 9?

Editting PDF documents that were created by a MAC doesn't work because of font incompatability. How can we get MAC fonts and load in our Adobe Acrobat Pro 9?

If it's a Mac font and you're on Windows, you can't. If you are also on a Mac, you'll need to purchase the fonts (fonts are generally non-transferable, like software. One of the reasons pdf exists), install them and try your edits.
But it's best to edit the original document and create a new pdf when finished.

Forgot my passcode and the computer i backed it up on doesn't work, what can i do.

forgot my passcode and the computer i backed it up on doesn't work, what can i do.

Erasing the device is supposed to erase the passcode which is supposed to allow you to activate the device again. Let it go for the 10 minutes and then see if you can activate it again. You can also try erasing the device again and see what happens.
Go to icloud.com/#find.
If prompted, sign in with your iCloud Apple ID.
Click All Devices at the top of your browser window.
Select the device you want to erase.
Click "Erase [device]" to erase your device and its passcode.
Use the Setup Assistant on your device to restore the most recent backup.
This is what Apple recommends, so you have to trust that it is going to work .....

Compressor 4 doesn't work since I installed Mavericks and I can't export a video normally on FCPX either.

Compressor 4 doesn't work since I installed Mavericks and I can't export a video normally on FCPX either.
Can someone help me?
Thank you!

Got the phone direct from the Apple website, so I assume it was unlocked, and it had been on giffgaff ever since but I don't see why that's a problem?
The carrier was automatically selected as Free and is up to date.
There seemed to be no problem that the SIM was being used in an iPhone 4 and my friends in exactly the same situation (e.g. arriving in France and moving over to the Free network with iPhone 4's) have had zero problems with their 3G network; it just seems to be me.
The Free Mobile Network is included on this list which I guess means that they are Apple-approved? iPhone: Wireless carrier support and features
How do I find out whether or not I would need to manually configure an APN? I'm not even sure I know what that is.

Back to my mac isn't working properly

After downloading Mavericks, (which went without a hitch), I am now receiving an error in system preferences stating: Back to my Mac isn't working properly
because the DNS server isn't responding. Contact your internet service provider for a different DNS server address, enter it in Network preferences and try again.
In reality everything wireless is working; the internet the printer iPad works fine.
I went to the Airport utility and clicked on my Time Capsule and it states: Change Airport base station from using DHCP and NAT to Bridge mode.
I done that and everything related to the wireless router runs real slow, I mean real slow. It took just under 4 minutes for my Time Capsule to recognize the computer. Due to this I received all kinds of errors from the printer from Airport Utility and the iPad.
I need a fix please, I've read all the support documents related to this in the support community and either the answers given I have tried with no success or they do not relate to my situuation.
Thank you for looking at this, I only hope you have a valid answer.
Jerry

New to BTMM, I got stung today with the silly DNS problem message. Solution:
1) Flush DNS cache with:
dscacheutil -flushcache;sudo killall -HUP mDNSResponder
2)System preferences > iCloud > untick BTMM then tick it again. The warning should have disappeared.
Edit #1
Apologies for the noise. The warning has come back
Edit #2
Just found out that BTMM is not compatible with double NAT. That's not helpful.
http://support.apple.com/kb/TS1208

Back to my mac doesn't work since I change from me to iCloud

Similar Messages

Maybe you are looking for