Bad file signatures firmware upgrade MI424WR rev G

Hello,
I am not entirely sure if I needed a firmware upgrade since all was working ok, but when I attempted to upgrade the firmware on my MI424WR rev G router to to 4.0.16.1.56.0.10.11.6-MI424WR.rmt I got an bad file signatures error msg. I tried it several times and doublechecked I had the correct router model. Also, is this device supposed to be downloading and installing such updates by itself? Thank you.

The ActionTec routers are set by Verizon to automatically download firmware upgrades, so yes they are "supposed" to. At times you can run a manual firmware upgrade or even downgrade if you are having issues.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Similar Messages

MI424WR (Rev. F) - Wireless Broadband Router - Need Rev G for NAS

I want to put a Buffalo NAS storage device on the USB port on the MI424WR (Rev. F) - Wireless Broadband Router, but Actiontec says a firmware upgrade to Rev G is needed to do this. If I do the upgrade (will it even allow it?) will I trash my router such that it won't work (and I may not be able to restore it to Rev F)? Anyone have any experience attempting this?

davef wrote:
Not sure what you mean by "not enabled". I use this USB port on the router to charge my EVO smartphone.
There is indeed power on the USB port, so charging USB devices does work.
What I meant by "not enabled", is that there is no firmware support of any kind.
No mass storage driver, etc.

BDX2300 firmware upgrade fail (USB)

I have had mulltiple screen freezes on most Bluray discs I have tried. I see there is a firmware upgrade 1.15 to stabalize, but...
I have followed the instructions for copying the files for firmware upgrade to USB drive in Directory UPG_ALL. When I plug the USB drive into the player, I see the USB icon loading, but the player does not try to load the firmware as the instruction states:
3)
“Insert the USB Thumb Drive with the firmware” copied to the drive into the USP port located on the front. (Note: Some models may have the USB port located behind a protective cover or on the rear of the unit)
4)
After a few seconds the update screen will appear. The unit will automatically update the firmware in sequence as shown in Figure 1a through 1d.
If I go to Setting, system, and try to upgrade from USB, I get a messsage that the file is not found. I have verified the files are in the directory as requested.
What are the correct instructions that will allow me to update my firmware via USB?

I just successfully upgrade my brother's machine thanks to this forum:
Here is what worked for me with upgrade V1.22. after much trial and error: (Your folders will have your version in the name)
Unzip the downloaded zip file. There is a real nice PDF file that tells you exactly how to do it. THROW IT OUT!
On a clean thumb drive (don't worry about BUDA and System Volume information) create a folder named UPG_ALL.
When you unzip your file you will find, besides the PDF file you should dispose of, a folder named V1.22. In that folder you will find yet another folder named V1.22.
In that folder you will find some files: I had the following in mine:
8551_linux_demo_dbg.bin
8551_linux_demo_dbg_id.bin
DVD.bin
dvd_id.bin
mt8551_bl_linux.bin
Copy those files to the UPG_ALL folder on the Thumb drive.
Now some of you may have gotten this far before, what they didn't tell us was that you can tell the player to look on the USB port.
With thumb drive inserted and the power on select the icon on the tv screen with the gears. Then select SETTINGS and then select UPDATE.
You should now see a choice for disk - USB - or network (or something like that)
Select USB and wallah you should have an update occur.
This last part was strictly from memory, because I couldn't interupt the movie my brother was watching.
I hope this helps,
Jerry

Linksys e4200v2 firmware upgrade fails -bad file

I'm trying to upgrade my frmware to the lastest one (classic firmware)
I've downloaded this file multiple times http://homedownloads.cisco.com/downloads/firmware/1224693043651/FW_E4200_2.0.37.131047.zip
When I try the firmware upgrade (manual upgrade) and select the file, it always complains about the file being corrupt (using the .ssa file in the zip).
How can I solve this issue?
Kind Regards, Jurgen

Hi, I’ve noticed that all smart routers’ classic firmware starting from E4200 v2 to EA4500 contains .ssa as the file extension. So, the moment you load a firmware with that file extension then the router should automatically read it. What you can do is to use other browsers or better yet use another computer just to isolate the problem. If that will not work then try the following:
Download the tftp utility (select version 4)
Disconnect the modem from the router and just have the computer connected to the router's ethernet port
Assign a static ip address on your computer
Lower the speed of the computer's LAN card to 10 half duplex
disable any firewall or anti-virus software on your computer
Run the tftp utiilty

Firmware Upgrade now no file sharing

I recently installed a firmware upgrade on my E3000 to firmware version 1.0.04.build 6. Since the upgrade I am unable to see any of my files on my network computer which is running windows 7. Before everything was fine and I could stream to my dvd players and dish receivers. I've tried everything I can think of to fix this problem. Any help would be greatly appreciated.
Thanks in advance.

Hi Mr. Bernard,
Thank you for your question.
However, the Small Business Support Community is limited to Cisco Small Business Products and the E3000 is not a Cisco Small Business Product.
Your question below relates to a Cisco Consumer Product which our community would not be able to help you with.
The best area for you to post your question would be at the Linksys by Cisco community: http://homecommunity.cisco.com/community.
Regards,
Diego Rodriguez
Cisco Small Business Community Engineer

Firmware Upgrade for Actiontec GT704WG Rev. B Router

How do I find the firmware upgrade for the Actiontec GT704WG Rev. B Router? Almost everytime I try to get onto the internet, I have to run the troubleshooter because there is no connection and the final diagnosis is that "The default gateway is unavailable." Googled and found that it is due to the need for a firmware update for the router but cannot find one on the internet. Help!!!

Hi Funrunner
You didn't say which version of the firmware you are currently running, however the latest firmware for that router is Version
3.20.3.3.5.0.9.2.14
Thank you,
Peter
Peter_VZ
Verizon Support
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

I have Lightroom 4.4 and a Nikon d800 with firmware upgrade 2.005. raw files are now since upgrade, unreadable. any plugins or advice? Thanks

I have Lightroom 4.4 and a Nikon d800 with firmware upgrade 2.005. raw files are now since upgrade, unreadable. any plugins or advice? Thanks

I select the images I want uploaded, NEF files, click the "IMPORT" button, process bar comes up and shows work in progress, but no progress. after about 2 minutes, dialogue box appears with message: "unable to import because the following files are unreadable: NEFxxxx, etc."

N73 Firmware upgrade--- bad working Voice dialing

I updated the firmware of my Nokia N73 from 268.0.0.3 to 368.0.0.1. With the older version delivered by the phone voice dialing worked. In the 268.0.0.3 I only could given voice command for the profiles not for the contacts. It didn't recognise any contact. Because of thos I decided to do the next firmware upgrade to 368.0.0.1 and now the voice dialing doesn't work at all. Each time I put the button to activate it tells me "fualty voicesystem"in dutch "fout spraaksysteem. Now it became even worser. Is there anyone who helps me out?
regards

16-Dec-2006
03:34 PM
conradus wrote:
Thank you for your reaction. I put the firmware for the second time to my phone. Now it seems working again. When I touch the button for voice dialing it works untill then. But I may ask for every contact in my contactlist but nothing happens. When I touch the button again it is not reacting then but only the second time. When i asked for an other profile it sometimes works. In my contactlist it is possible to hear the contactname. But via voice dialing none of the contacts to choose.
best regards
Voice Dialling seems to be a bit choppy on most of the N-series models, because they use speech synthesis. Whereas this works for profile names, it's a different tackle for contact names. This is because contact names are assigned by assigned by you, the user. If you select Play Voice Tag for any given contact in your phone, it will output this name using speech synthesis. You will have to EXACTLY copy this output. And, if the name of a certain user is "John Doe Geralds", it wouldn't suffice to simply say "John Doe". You'd HAVE to put Geralds behind that, and in the EXACT same way as the device says it.
The only way to change a voice label for any given name is to change the name itself. The same goes for profile names and commands, but I wouldn't change these as the defaults work fine.
A reason because of which voice dialling may not work can also be found in the user's voice details having become useless for the phone. To correct this, go to Tools> Voice commands > Options > Settings and choose: Reset Voice Adaptations. Note that carrying this out means that ALL data collected about your voice shall be lost; you might have a bit of difficulty using voice features the first couple of times after performing this instruction. Beware to EXACTLY copy whatever the phone says, even though you know real-world pronunciation to be different. Until now, I haven't had to actually adjust the pitch of my voice to the synthesizer's pitch, but I know this would improve recognition accuracy.
Oh yeah... Sorry for my late reaction!
Best regards,
V3.0704.1.0.1
19-01-2007
RM-133 Nokia N73(57.01) Product Code:0539338

Problem Upgrading Router Firmware on MI424WR-GEN3I

Having trouble updating my router firmware. Current version says: 40.21.18. Status says: OK. However, it says this below:
" Internet Version: Old Wireless Broadband Router version 40.21.10.3 found?
Does this mean anything? I'm wondering if the firmware is still not upgraded. Any thoughts on this? Did my firmware upgrade?

Your configuration indicates you do indeed have the latest firmware version installed. The Internet version is what is available to restore to a previous version, should you ever have the need to do so.
You can see how this would work (without actually activating it) by clicking on Advanced > Firmware Restore. It will show you what your current version is and the previous version that's avialable to restore to.
Once you've taken a look, click on Cancel to avoid actually reverting to the older version.

The firmware upgrade file is not supported on this hardware version MI424-WR Hardware Ver. C

Hello - I have been troubleshooting for quite some time a problem that only occurs on my wireless devices. 8 out of 10 times I fail to obtain a IP address from my MI424-WR. My connection to the device is successful, however, DHCP times out. I have connected to many other wireless routers in other locations in the last 4 weeks and have isolated my issue to my connection with my FIOS router. That is to say that when I am elsewhere I do not have this problem. I contacted support today, and the tech I spoke to was very nice and also clueless. What is the latest/current hardware ver of the MI424-WR Verizon is shipping? The tech said he could not tell me what ver the one he had in a lab was. If l log into the router under firmware upgrade I notice the message in my subject. I have had FIOS here with the same router since 9/2007. Any help would be apreciated.

That brings up something I have been curious about...could you see if this might work for you?
-First and foremost, log into the router
-At the top click Wireless Settings
-Go into basic security settings on the left and change the channel to 11 (yes, I know this doesn't work for all but please read on) and apply
-Now back on the left side menu choose advanced security settings, enter 802.11b/g Mode
---Honestly, most people should need G only by now, but choose what you need here (avoid mixed) and apply
-Go back onto the left menu and try advanced wireless settings again but this time choose "Other Advanced Wireless Options" at the bottom
-Change MTU to "manual" and enter in "1492" in the field it provides and apply
-Now at the top right go into advanced settings
-Click on the link for "System settings"
-In here UNCHECK the "Enable Logging" and "Low Capacity Notification" options and apply
I don't think they would be able to tell you which version is being shipped, because I am sure the new routers are coming with the new firmware and the old they send out first. But yeah, give that a shot and see if that does anything to help your wireless machines connect. I am kind of curious if that will change anything.

Does Mac Migrate copy bad files/sectors?

I upgraded my MBP internal hard drive to a Samsung 1TB and it crashed for the 2nd time (will never buy another Samsung). So this time, I purchased a WD and migrated my system to the new drive sucessfully. I just wanted to see if anyone knew if the migrate function simply copies files or if it copys sectors of the hard drive. Basically I just want to know if Mac Migrate will copy the crap from the Samsung drive that might cause my new WD to act up - or if that's possible?

Migration copies files. If the files are corrupt, the corrupt data will be copied, but it won't affect the integrity of the disk in any way. If the disk that you are copying from has bad sectors, the copy may fail outright. If the disk can't be read, it can't be read.
Contemporary hard disks track bad blocks in firmware on the disk. Formatting and zeroing out the disk will force the disk to refresh it's internal map of bad blocks. All disks have a certain number of bad blocks on them at the time of manufacture, and these blocks are already mapped and ignored when you receive a new drive. The appearance of new bad blocks on a disk generally indicates either wear or a manufacturing defect. I would treat a drive that 's accumulated new bad blocks as a drive that has reached then end of its operational life and replace it.

BEFW11S4 V2 Firmware upgrade problems

I am trying to upgrade my firmware on my BEFW11S4 V2 because I am having difficulty maintaining a connection to Entropia Universe.
I read the instructions carefully, but they refer to a zip file and when I download the firmware it is not a zipfile at all, but a bin file. I assume that this is the file I need so I put the location in the box on the upgrade page using the browse button and then click the upgrade button. It looks like it's going to do its thing, but after one cycle of the blue line and about halfway through on the second time I get a message about an invalid code pattern.
The current firmware version is 1.44 from November of 2002 and I am trying to upgrade to 1.45.10. The actual file name that I downloaded is
befw11s4v3[1].2_v1.45.10_fw.bin and it is on my desktop.
Thinking that I may have got a bad download, I downloaded it again -- same results.
What am I doing wrong?
Larry
Message Edited by larryludwick on 04-04-200710:31 AM

well....go to www.linksys.com/download and download the setup wizard ....
connect a computer to one of the LAN ports on the router...on th computer go to network connections >> right click LAN >>properties >> configure >> Advanced >> under the properties column select Link Speed >> 10 Mbps Half Duplex Mode.....
Assign a static ip add to the computer.. 192.168.1.10 and default gateway 192.168.1.1 ...
run the setupwizard.exe file .. here the server is the router's ip add i.e 192.168.1.1 , password is router's password ( by default "admin") and browse the firmware file and click upgrade....
also , ensure that the firewall is disabled on the computer..

BEFW11S4 constant disconnect after firmware upgrade

I was having trouble with my router losing connection every 2 hours or so . I have downloaded and installed the latest firmware and now it keeps disconnecting almost every 30 min. I have a static IP on my main pc and dhcp enabled for my xbox360. I have checked the cables if they were bad by swapping them but the problem was still there. Any help would be very much appreciated.

After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Also, please list all the static LAN IP addresses that you are using on your network.
If you are not using the default DHCP server range of 192.168.1.100 thru 192.168.1.149 , then please state your DHCP server range.
Are you running any peer-to-peer (P2P) software? If so, this is a known cause for router slow downs and disconnections. Temporarily stop using the P2P software, then reboot router, and see if this corrects your problem.
Who is your ISP? Are you on a cable system? Some cable systems monitor the MAC address of the devices connected to them, and eventually boot off any MAC address they don't recognize. If you are on a cable modem, try cloning your MAC address (done in the router), and see if this corrects the problem.

Cannot perform JetDirect firmware upgrades

I was recently tasked with making sure the firmware was up to date for all the printers in the building. I still have 8 more that I have been unable to update. I used HP Download Manager first, and it was very good at telling me which printers needed firmware updates, but it failed every time I tried to actually perform an update. So, I downloaded the firmware files manually, then used the web interface of the printers to do the firmware updates. Except that a number of them did not include an "upgrade firmware" option. So, then I tried to FTP the firmware file to those printers, following the instructions here. Every time I tried that, the printer would just start printing garbage, interpreting the binary file I was sending it as if it was a print job. Of note: the instructions say to do a "cd DOWNLOAD" command, but not to worry if that directory does not exist. On every one that failed, and just printed garbage, the "cd DOWNLOAD" command failed. I even connected directly to the printer with a crossover cable, but then you still have to follow the FTP instructions, and it does the same thing.
So where do I go from here? How do I perform a firmware upgrade without the printer interpreting it as a print job?
Here are the models of the JetDirect cards I am trying to update:
J4169A
J6057A
J3113A
J3111A
J2552B

First thing you can try is just to save the firmware file to the root (c:/) and run the ftp command from the root which negates any need to change directories.
Second thing to consider - what printers are the JD cards installed in? Some of the printers will automatically update the firmware for the JD card when you do the printer firmware. More common in those with internal JD cards but I have seen a few printers do the double update with the accessory card.
(oh, and you are ftping to the IP address of the printer, not connecting via parallel, correct?)
One of the simplest ways to ftp is to use an IE browser (preferably IE 6), enable view folder option for ftp in the advanced internet options and then use the browser to ftp to the printer (ftp://xxx.xxx.xxx.xxx). You should see a small folder icon. Some printers need to have the firmware file dropped beside the folder for it to work, some need it dropped right on the folder for it to work.
If that still doesn't work - drop the cards in one of the printers that did allow the update and see if that makes a difference. You could also try cold resetting the printers with the cards installed in case they were managed by Webjet Admin at one point and updates were blocked. You could also download and use Webjet Admin to do the firmware upgrades (this is a great tool for fleet management and being able to configure multiple families of similar printers at the same time from the comfort of your desk!)
insert signature here

PETITION: This is what I would like to see in a new firmware upgrade for the MTP ZEN TO

FIXES:
-Ensures correct playback on the player of Zencast audio content that has been transferred using Zencast organiser. Remaining time is displayed correctly, and rewind / fast-forward functions can be used
- Allows users to transfer tracks between folders on the player when using a program such as Creative Mediasource [THIS IS NEEDED FOR ALL MTP PLAYERS]
- Allows charging via USB when the player is not being used by a program or is low on battery [THIS FEATURE SEEMS TO HAVE BEEN REMOVED BY MTP UPGRADE]
ENHANCEMENTS / ADDITIONAL FEAUTRES [I HAVE LISTED THESE BY MY PERSONAL ORDER OF PREFERENCE]:
) Allows the playback of Audible content types ,2,3,4 on the player, via a plug-in in Audible Manager
2) Adds bookmarking feature to the player
3) Adds SmartVolume EQ feature to the player
4) Adds DJ menu to the player
5) Allows user to partition a section of the player for data transfer
6) Allows user to synchronise tasks from Outlook to the player
7) Allows TXT files/ Ebooks to be stored/ viewed on the player
8) Adds BassBoost EQ feature to the player
PLEASE SIGN THIS PETITION TO URGE CREATIVE TO INTRODUCE AT LEAST SOME OF THESE FIXES / FEATURES IN A FIRMWARE UPGRADE FOR THE MTP ZEN TOUCH - also please feel free to add other suggestions that would improve the functionality of the Zen Touch
Message Edited by joshua32 on <SPAN class=date_text>05-30-2006 <SPAN class=time_text>:7 PM
Message Edited by joshua32 on 05-30-2006 :8 PM

all of these would be awesome, as would lyrics support, I REALLY want that

Bad file signatures firmware upgrade MI424WR rev G

Similar Messages

Maybe you are looking for