Bad Install Disk

I have a 14 inch iBook, and recently figured out that my hard drive is bad. I can get on it, but the s.m.a.r.t. status is "failing". Anyways, I got a new external hard drive and I want to install Panther onto it, but the 1st disk is very scratched up, and when i start to install, it comes up with an error saying it can't read it, due to the scratches. Is there anyway I can get the system from my old hard drive to my new one, or do you think the Apple store would give me a new one? Thanks a lot.

StrangeBrew89:
In terms of the install disk, if you call Apple Customer Relations (not tech support) and tell them about your disk, the will replace your damaged disk for a small fee (about $20, I think). Lost disks cost about $60.
Kenichi has described how you can make a bootable clone of your entire Hard Disk Drive, Operating System and all, from the original HDD in a firewire enclosure.
If you plan to replace the internal HDD you will find directions at ifixit. The iBook is a bit of a chore getting into, but it is not difficult, just very intensive and time consuming. If you are handy with a screw driver you can do it. If you think you would like to do it, post back for some tips. Here is a list of available HDDs. You will not I selected an early model of 14" iBook since I am not sure of the exact model of your iBook. These drives will work on your computer. However, if you have a later model (after 2002), it will support a drive up to 160 GB.
Please post back with further questions or comments.
Cheers.
cornelius

Similar Messages

Bad install disk - unable to retry

Attempting to install Solaris on a laptop. The first CD went fine. The second CD failed about 70% through. Redownloaded and burnt the second disk, though I can't get it to reattempt the second disk install - it wants to go straight to 3, which, even when I put that in, does not recognize it as disk 3.
Very new to Solaris and unix/linux-like systems. Any way to restart my installation?

The best way to use a DVD which is faster and efficient.
Imran

Upgrade Help... is my install disk good?

Hi all... may your 2007 unfold as you prefer...
I bought Tiger and was testing out how it would run, on a cloned B/U firewire drive, before installation on my main drive...
I ran into install problems and after 2 failed attempts on the external drive i'm nervous to install on the main.
The last lines of the installation log reads:
"Dec 13 23:05:05 localhost : Performing post-extraction actions
Dec 13 23:05:05 localhost : SecAlternate system ("/Volumes/OSX B:U") returned 100079". Then it stalls and never finishes.
So here'squestions:
Do i need to have the upgraded disk set up for "Journaling"?
Could i have a bad Install disk?
AFAIK, no problems w/the drives nor w/present OS config.
Any thoughts, recomendations or support would be helpful as i'm at a loss here...
Pismo G4/550;SuperDrive;DLink BT;1GB RAM Mac OS X (10.3.9) upgraded CPU & Optical Drive!

Ce Ann:
Sometimes installing to an external HDD can be a challenge. I understand your hesitation to install to your Pismo and possibly mess things up. However, if you have a Full Retail Version of Tiger I don't think you need to worry.
Here's what I suggest:
1. Back up (clone) your entire HDD to your external Firewire HDD using SuperDuper. The point of this is that if the installation does not go well you can clone your HDD back from the external FW HDD.
2. Disconnect your external HDD from the Pismo.
3. Insert the Tiger install disk and boot up your Pismo holding down the "C" key.
4. When booted go to the Utilities menu and launch Disk Utility.
5. Select your HDD (manufacturer ID) in the sidebar.
6. Select First Aid in the main panel.
7. Click Repair Disk button.
8. If DU reports disk does not need repairs click Repair Disk Permissions button. Then quit DU and go to installation below.
9. If DU reports errors Repair again and again until DU reports disk is repaired.
10. If DU reports errors it cannot repair you will need to use a utility like Tech Tool Pro or Disk Warrior
I am assuming that your computer meets the minimum system requirements for Tiger.
Installation
1. You are already booted from the Tiger installer disk.
2. Lauch the installer by clicking Install.
3. After the preliminaries select installation option.
4. If you wish you may choose to customize and deselect Foreign Language Translations (if you don't think you need it--most people don't); also deselect Additional Printer Drivers.
5. Proceed with installation.
6. After successful installation computer restarts and you go through the setup procedure.
7. Restart and Repair permissions (Applications > Utilities > Disk Utility)!
8. Download and apply the Mac OS X Update 10.4.4 (Combo)
9. Restart and Repair permissions!
10. Run Software Update and apply all available updates.
As you may have noticed I am running Tiger on my upgraded Pismo and on a 500, and both run great.
Please post back with further questions or comments.
Good luck.
cornelius
Message was edited by: cornelius

Can't boot G5 even from OS install disk. Help?

I've trolled the message boards 25 pages deep and searched all the "Can't boot my G5" threads and still haven't found anyone describing what my machine is doing so thought I'd start a new thread in the hopes someone can help me out.
Ok I have a G5 dual processor machine. (Power PC chip, not Intel) Things went bad when I tried to do an Archive and Install of Leopard (OS 10.5) The install looked as normal until I got to one minute left on the install. At that point the install never progressed. I thought maybe it was doing some behind the scenes processing and decided to leave it over night. The next day my machine was still hung on that One minute left. So obviously it was a failure. Of course now the problem is I have an install that never completed of the OS and so that partition is, I assume, unbootable. Wiped away the Tiger OS and did a 99% install of Leopard. So I had to shut down by holding the power button.
I think to myself, "No worries I can just boot from my 2nd partition holding down the Option key to select it on the boot up screen". I always keep a partition with an OS on it for times like these. So I reboot, hold option key, select my other partition, things look OK. I get the grey screen with the Apple logo and I get the wheel animation turning. (Not beachball of death but the typical circular, almost sun ray configuration thing) At this point, usually the screen will go black for a moment before the desktop loads. However, in my case once the screen goes black after the load screen, it stays black. Now let me say the monitor does NOT turn off. There is a definite difference when I manually turn the monitor off. When off it's truly black. But this is like a power on black, not true black. (If you need me to explain this better feel free to ask me to clarify)
So the untouched, pristine Tiger partition boot is a No Go. I figured I'd then give up on trying to put Leopard on my desktop machine (I use it on my laptop) and reinstall the original OS and system software from the system disk that came with my G5. I boot machine holding down eject button, place the disk in, close the drive door and shut down again by holding power button. Reboot holding C key and the same routine happens with booting from the disk. Gray Apple logo screen, sun ray circle moving, screen goes black on the attempted transition to desktop .. but stays black. I also tried booting with my Disk Warrior disk to no avail. Same thing happens. (Also tried booting from disks by selecting them manually from booting with Option key down) At first I wondered if it was a monitor issue. That maybe my desktop was up but there was an issue with the signal being passed to the monitor on the resolution jump. Thought perhaps hitting the Eject key on the keyboard when I had attempted to boot from the partition (not from disk on this test) would tell me if it was a monitor issue. If it was a monitor issue, the disk tray should open. But alas, no.
So since I cannot boot normally from any partition or disk I decided to boot into single-user mode.
I did the fsck -fy thing and it told me everything was ok. I had also previously installed applejack and I ran that and short of correcting a few permissions and dumping some unneeded caches it came back with a system OK.
At my wits end I booted into target disk mode and ran Disk Warrior on both the original half installed OS partition and the back up emergency boot up partition from my laptop. Again, everything OK. Hoped against hope that I could actually install an OS onto my G5 from my laptop but I was only given the option of being able to do it from my laptop with the Leopard disk and it would only allow me to do it if I used Disk Utility to completely format that drive first. No, thanks.
Re-attempt to boot G5. Failure. So now I turn to hardware. Disconnected everything beside the keyboard and mouse. Try again. Fail. Pulled a couple sticks of Crucial memory out of the machine and left the stock RAM. No dice. Pressed the small power unit reset button under the RAM slots. No change. Zapped the PRAM. Still nothing. Try to boot in Safe mode holding down shift key. Doesn't work.
It seems to me if I can't even get the machine to boot from the Install disk that there is something going on that is much more major than software issues.
Bad motherboard? Any ideas? Because I'm all out of ideas.

Brother, Sound74, I thought I was the only one pulling the hair out of my chest one by one the past two days. Your situation is very similar to mine, and I'm just as clueless as you are. I started getting kernel panic screens, then nothing on boot, until finally I brought it to the local genius bar. They ran all the usual software/hardware tests, updated Tiger to 10.4.11, recommended I buy Leopard and do an erase-install. My computer, of course, was working absolutely fine by this point. I bought Leopard, came home, backed everything up, then tried to install the new OS. Like in your case, it just up and quit half-way through. Screen went black and a "No DVI Signal" message came on my display (it does this when I turn it on without first turning on the computer).
So I thought, well, maybe it takes a really long time to erase-install, and the monitor is just waiting for things to kick back in. I've always upgrade-installed before, so I couldn't tell if this was normal or not. But about half an hour later, my fans kicked in so fast I thought I had a P-51 Mustang taking off in my studio. I waited a bit more and finally force-shut-down my system. Not knowing what to expect, I nervously tried to re-boot.
Nothing. Zip. I can't safe boot, I can't boot from the installer disc, etc. The only thing I can do is the option-key thing whereby you choose the startup disc. And of course, it only gives the Leopard install disc as an option, because now the entire HD has been erased! But when I choose the Leopard disc, of course it doesn't work.
So I have a nice $3000 paperweight sitting in my studio. I guess I'll have to bring it back to the Mac store, where if it costs more than $300 to fix, I'm going to say screw it and put that dough toward a new iMac.
Sorry I couldn't provide any helpful info, but I just wanted you to know you're not alone in suffering the slings and arrows of outrageous technology.
Keep me posted on any solutions you discover, and I'll do the same.
Noochy1
PS My applecare expired a month ago! AAAAARRRRGGGHHHH!!! **** Murphy and his stupid laws.

My iMac is no longer recognising my windows 7 install disk.

My 27in iMac is failing to recognise the windows install disk as I try and install it in a virtual machine using VMware fusion 3. It has managed this before, and I had been running it successfully for over a year but (as is often the way with windows) a clean install was needed. The iMac is still running snow leopard ( as before) it and fusion are patched up to date. Nothing different than before. I've even tried a different windows 7 disk and the iMac simply ejects it with no message. It does manage to recognise every other disk it insert. No messages given. Any clues out there.

appears that apple has changed SMB code, and now its not possible login from windows on mac.
i installed snow leopard and now works fine.
apple is capable to make it run paying new license of smb code, but isnted of this, apple has created new protocol smbx and now, all others need to adapt your code to apple..
bad movement.. i am thinking sell imac and no back to apple anymore..

Need to restore TM backup to 2nd HD w/o install disks (1 mac)

hi all,
i've run into a quandry. my powermac g5 primary drive (OSX10-5) is throwing i/o errors. i have a recent TM backup, and would like to restore it to my secondary drive (MacOS), and reboot from that drive. then i can work on the primary drive. the panther install on MacOS no longer boots, so i want get 10.5 on that drive.
my dvr-116d cannot read my leopard install disk (nor any other disk). i have a WD mybook -- it's my TM drive. (how about that for irony?) i followed the thread on the WD and DVR mis-interaction, but none of the suggested fixes have worked (no WD plist file to delete, have updated drivers and firmware, rebooted without drive, etc). thus, i can't restart from the leopard install disk. my other systems are all snow leopard, which won't run on the g5, so that rules out the 2nd mac method.
i have made few attempts without success. first, using disk utility (DU), i tried to create an image from the TM OSX10-5 backup. it hung after 30 hours of "creating disk image..." second, i tried using TM restore to different target to put the files on MacOS, and ended up with /Volumes/MacOS/OSX10-5. using DU again, i turned that into a disk image, reformatted MacOS, and restored from that disk image. the result won't boot properly (system tries to booth, then powers off in about 15 seconds). on reflection, the FAQ did say "to restore a data-only volume to an alternate location", so i shouldn't have expected it to work. i'm currently looking into migration assistant...
the primary disk is on borrowed time, so i'd be grateful for any/all ideas/help. (too bad i can't just dd the backup onto a reformatted volume like the old days.)
many thanks,
bert

Another alternative for booting the Leopard install disc would be to "borrow" the DVD drive from one of your newer computers via FireWire Target Disk mode. You would need an appropriate Firewire cable that could connect the two computers.
In this situation you can't set up FireWire Target Disk mode with the Intel as the host computer, but you should still be able to use TDM "the other way", using the computer with the functioning DVD drive as the TDM target and and running the Leopard DVD from the G5 as host. The newer Intel Mac is used only for its DVD drive, and is otherwise totally passive.
To try this, you could do the following:
Shut down the G5. Insert the Leopard DVD into the other computer, and restart the other computer while holding down the T key, booting the other computer into FireWire Target Disk Mode . Connect it to the G5 with the FW cable, and then start the G5 while holding down the Option key. This should boot the G5 into the startup manager, and hopefully you will see the Leopard OS X install DVD as one of the startup choices. Select that, and try to boot from it.
Message was edited by: jsd2

Mac Pro will not boot from Leopard or any CD or DVD install disk

My Mac Pro wont boot from my Leopard install DVD. It never gets by the gray screen, then after several minutes the screen scrolls down black and says I need to restart my computer. I tried my Tiger install disk and it still wont boot from that DVD. Held down the "C", used "option" and selected DVD and still no boot. I can boot from one HD that has Leopard 10.5.8, but another HD with Snow Leopard 10.6.3 will not boot. The HD with Snow Leopard shows up as "EFI Boot" not the name I gave that HD when I startup using the "option" key. Any help would be appreciated.

At first I was just going to say it sounds like you have a bad optical drive, but then you had to go and say that it also won't boot from a HDD.
That just makes things a whole lot worse.
Start by removing the side cover and checking the RAM to see if any of the LEDs are lit up indicating bad RAM. Usually if there's any bad RAM found, it will just automatically disable that stick, but maybe yours isn't for some reason.
Look for any other LEDs that may be lit. Generally speaking, the only time you should see an LED (outside of the power LED) lit consistently is if there's a problem.
You should also see if you can get Apple Hardware Test to run, which may or may not find some problem.
But sorry to say, it's sounding very suspiciously like a bad logic board.
One other thing to try, is putting the SL drive into a different slot. So if you were putting it in slot 2, try slot 3 or 4. If you just have a bad SATA port, you might be able to just work around that until you get a new system.
If by chance this system is still under warranty, do not walk, do not pass go, do not collect $200, RUN to the nearest AASP or Apple store to make it THEIR problem to sort out.

Pismo won't boot from install disks

Hi! I've looked to find the answer elsewhere, but no luck... apologies if this has already been answered.
I have a Powerbook G3 Pismo which I now need to use to run Hypercard. (Yes!)
It has been sitting unused for over a year.
It didn't start up.
I found an article that explained how to remove the PRAM battery. I did so. It starts up fine when connected to power.
I have ordered a new PRAM battery, but it hasn't arrived yet. I decided to go ahead and try to get it to boot.
When I powered up, I got the alternating icon saying it couldn't find an installed system.
I guessed that the hard drive had become corrupt, so I rebooted into Target Disk mode. It worked!
I connected it via FireWire to a MacBook Pro. The Pismo did show up as an external firewire hard drive. Good!
Using OS X Disk Utility, I erased the Pismo drive.
I couldn't decide whether to use OS X Extended, or OS X Extended (Journaled).
I didn't know about any options to install drivers for OS 9, so I probably did the wrong thing. (Pismo can boot into either OS 9 or OS X, I think.)
I tried to fix this later (see below).
I disconnected the Firewire and shut down.
I finally got the Pismo to boot up from a MacWarrior CD (a 3rd-party disk utility that fixes directory problems). I used it to fix the directory.
It still wouldn't boot from the original disks that came with the Pismo. The optical reader whirred away, I got a blank gray screen, it whirred again, I got another blank gray screen, but the cursor never showed up in the upper left corner. After half an hour, it had made no progress.
I reconnected the Pismo to the Macbook Pro using Firewire.
I tried to install Tiger on the Pismo using my officially purchased, large-box Tiger software. The Macbook Pro mounted the disk, but when I ran the installer, it told me I couldn't install Tiger on this machine (the Macbook Pro, duh!) and only gave me the option to quit.I thought that I could use an all-model install disk to install OS X on ANY external hard drive! What gives???!???
I tried to boot from the AppleCare Protection Plan's TechTool Deluxe.
It seemed to be booting fine into 9.1. Yippee!
It halted with a System Error (address error) telling me to restart holding down the Shift key.
I do so. It seemed to be booting fine into 9.1 again, Extensions Off.
But it halted with the same System Error.
I read about OS 9 drivers and went back into Disk Utility using the Macbook Pro.
Using Firewire to access my Pismo hard drive, I re-erased everything and made the partition have an Apple Partition Map.
I did not see any option to check or uncheck that mentioned installing OS 9 drivers. Did I miss it? Was it not there because I'm using a recent version of Disk Utility?
Same problems. Can't boot from the original Pismo "Software Restore" or "Software Install" disks, nor the TechTool Deluxe...
VERY FRUSTRATING! Have I tried everything? Has the hard drive gone bad?
Any help would be appreciated.

My new PRAM battery has been installed. I reset PRAM by doing a command-option-P-R.
The problem remains, but it's getting more consistent, which I guess is progress. With the Pismo connected to AC power (all my batteries are, of course, dead by now), the following has happened:
When I start up with the Tiger installation disk, everything goes smoothly, the gray Apple logo appears, and then, suddenly, a flurry of white text on an irregular black background floods the screen. Darwin says there's a kernel panic and they're in a loop ("we are hanging here").
When I start up with the original Software Restore disk, the blank gray screen blinks, turns a different shade of gray, the cursor arrow shows up in the upper left-hand corner, and it hangs. The cursor arrow doesn't respond to the trackpad; it's frozen.
When I start with the original Software Install disk, the same sequence takes place, but there is no cursor arrow that shows up. It just has the gray screen, a blink with a slightly different shade of gray, then it hangs.
The behavior is exactly the same for all 3 disks (respectively) when I use the MacBook Pro to start up:
Insert Pismo or Tiger disk into MacBook Pro (counterintuitively).
Start up the Pro in Target mode. Connect to Pismo using Firewire cable.
Start up Pismo. Pismo takes awhile to notice the Firewire disk, but eventually does.
Then it tries to use the disk in the Pro, but ends up acting case-by-case as it did when each disk was in the Pismo's drive (kernel panic hanging, gray screen with arrow, gray screen without arrow).
Helllllp!
My last chance will be to take a hard drive from a defunct ice iBook (dual USB) and use it to replace the factory-supplied Pismo drive. That iBook was a G4; the Pismo is a G3 (I believe). If there has developed a deep, difficult problem with the Pismo's hard drive, hopefully this will solve it:
I will try to boot from the iBook-drive-in-the-Pismo. I doubt this will work. If it does, great! If not...
I will try to boot from the Tiger installation disk, and if that works, try to install the Tiger software on it.
If that doesn't work, I will try to boot from the Software Restore and the Software Install disks.
If that doesn't work, I give up!!!! Unless someone here has a better idea.

Can't get past language selection with Leopard Install disk

My 1 year old Intel Mac Mini, which had been running 10.5.4 without problems suddenly froze up. The mouse was still active but I couldn't click anything. I turned the system off with the power button. When I restarted it got as far as the login screen, but clicking the user didn't do anything. I was able to log in using safe mode (hold down shift when starting). I ran the disc utility, repaired permissions and verified the disc. Seemed OK, but still the same behavior (freeze at login screen) when I try to boot normally.
I tried booting from the Leopard install disk. When it reached the language selection page there were some strange-looking horizontal lines in the display. Clicking the "proceed" button caused a copy of the button's graphic to appear at the top of the page and nothing else happened. Very puzzling, since I had upgraded OS X using that same disc.
I have a Superduper backup from a couple of weeks ago. It won't boot up normally either. Any ideas? Unfortunately, I'm 2 weeks out of warranty!
Thanks,
jwstex

I would probably start looking at the ram to see if it's worked loose or a board has gone bad (rare, but it happens).
Make sure no external drives or other unnecessary connections.
If the ram doesn't fix the problem, then you could also Zap the PRAM by holding down the Command + Option + P + R keys during boot up. Hold down the keys until the Mac goes through 3 startup chimes, then just release the keys and continue to boot normally. Check your clock settings if it boots.
http://support.apple.com/kb/HT1379

Reinstall OS hangup: Install disk can't find hard drive

Hi all,
I'm trying to reinstall OS X.3 on my daughter's iBook G4. I had it running ok but Safari wasn't working so I decided to do a clean install of the OS.
Somewhere along the line the internal HD disappeared from the install disk's radar, so to speak. If you're familiar with the install sequence, I can pin-point where things go wrong. Right after the window concerning software agreement--where you check "I agree"--the next window instantly opens asking where to install the software. The problem is the window does not show any drive to select. It's all just white space.
The reason I have to keep trying to reinstall the OS is that if I allow the computer to boot itself, it will display the prohibitory sign (circle with diagonal line) and that's as far as it goes. I have tried using the original install CD, another Panther disk, a Tiger disk and TechTool Pro 4. I've also been able to bring up Apple's own Disk Utility but it can't repair the disk--something is wrong with the allocation section of the volume structure, it reports.
Here's another clue: The battery will no longer hold a charge. This created a bad situation during my first attempt to reinstall the OS, because the power cable accidentally got pulled out and there was apparently no power in the battery so everything grounded to a halt. I haven't been able to get the computer to boot up since.
I realize I may have to erase her drive in order to get up and going again, but, failing to heed Daddy's past warnings to Backup! Backup! Backup! she has no way to restore her data. This is, of course, tragic.
Any ideas? Any lifelines to throw out?
Thanks for reading this rather lengthy post. Help, as always would be most appreciated.
Ddale53
Powerbook G4 Mac OS X (10.4)
Powerbook G3 Pismo FW Mac OS X (10.3)
Powerbook G3 Pismo FW Mac OS X (10.3)

You need to reformat the drive before reinstalling the OS or do an Archive install. It wont let you install the OS because there is a newer version installed (is it upgraded to 10.3.9?).
From the sounds of things you'll want to do an archive install. Go down to options (it will show up on the bottom of the installer window where the drives show up). Then click on it and select archive install and away you go.

How do you make a bootable install partition from a disk image of an install disk.

I have an iMac g4 running Leopard and would like to install OS X 10.3 on a different partition Leopard is on. However the super drive in the iMac will not read the disk I have, so I used my MacBook Pro to make a disk image of the install disk to use to install on the iMac. I do not know how to make the disk image into a bootable partition so I can install 10.3. The person I bought it from has already created a partition of the Leopard install disk and it is bootable but I do not know how he did this. Please help me. Thanks!

However the super drive in the iMac will not read the disk I have, so I used my MacBook Pro to make a disk image of the install disk to use to install on the iMac
Could be the cd is bad. Could be a bad cd reader.
I' not sure what you are trying to do.
To install,
-- you need to boot from a cd.
-- copy a working installation from another partition. try carbon-copy-cloner
-- could try target disk mode. There is a cd sharing mode.
"Installing OS X 10.4 'Tiger' on DVD-Challenged Macs Using FireWire Target Disk Mode" Should work for 10.3
http://lowendmac.com/misc/06/0710.html
Here is a picture of a firewire port:
http://upload.wikimedia.org/wikipedia/commons/thumb/b/b6/IEEE_1394_Firewire_PCI_ Expansion_Card_Digon3.jpg/800px-IEEE_1394_Firewire_PCI_Expansion_Card_Digon3.jpg
cd sharing across ethernet. Not sure if this works for booting.
http://support.apple.com/kb/HT5287

Eject the install disk

Hi. Please help. My install disk appears to be hanging on the grey Apple screen at start-up. I've not yet installed Leopard. I just want to eject the disk. How do I get it out of the computer. I'm thinking I got a bad disk.
Thanks. Dan

Dan Slocum wrote:
I watched the Genius (nice guy, by the way) clean the disk and then it operated perfectly. He said he'd seen several filmy DVDs from the factory and they cause hanging screens.
Dan
I can understand this to be a problem. The optical drive is barely reading the DVD, but just enough so it does not give up. Typically, a drive will re-read a sector several times if it experiences a problem. So imagine if much of the DVD had this film on it - - the installation might finally work, but only after the drive struggled with the DVD for a very long time. Also, at some point, the computer or drive might get really hot and make things worse.
I think this is one of the major problems people have been having, with no explanation until now.

Leopard install disks being scratched during install

I have had a couple of very strange experiences trying to install Leopard (upgrading from 10.4.10).
I initially ordered (at a special price) and received a Leopard disk under the program whereby I had purchased my MacBook Pro within the month prior to Leopard being issued. When I attempted the install, it moved along fine and then midway hung and finally said the install had failed--disk unreadable. I was unable to start up at all. Couldn't even eject the disk. Finally got it out. Did a clean install of 10.4. Reinstalled all my many programs and was determined to NOT use Leopard.
A few days later I looked at the Leopard disk and found that rings had been "scratched" or "worn" into the data surface as though my DVD reader/player had malfunctioned and been in contact with the disk surface. I was horrified and quickly looked at all my other program disks just used for the reinstallations, afraid the DVD player had ruined them too. They were all ok. This lead me to believe that perhaps the Leopard disk was bad even before I put it in my computer. I called Apple. They issued a new disk with barely a comment.
Well, I finally got around to doing an install of Leopard with the new DVD. I looked carefully at the disk first. No apparent ring scratches. The install worked--really slowly--but it finished and works fine.
However, when I ejected the disk, I took a look and, sure enough...the data side had rings scratched (or worn) into it as though my DVD player had been in contact during the installation process! They were not there before the install. This has NEVER happened with any of the other MANY installation disks (or disks I've burned) on this computer but has now occured TWICE with the Leopard install disk!!!! WHAT'S GOING ON?????
Has anyone else seen this issue?

DavidBJ wrote:
I have had a couple of very strange experiences trying to install Leopard (upgrading from 10.4.10).
I initially ordered (at a special price) and received a Leopard disk under the program whereby I had purchased my MacBook Pro within the month prior to Leopard being issued. When I attempted the install, it moved along fine and then midway hung and finally said the install had failed--disk unreadable. I was unable to start up at all. Couldn't even eject the disk. Finally got it out. Did a clean install of 10.4. Reinstalled all my many programs and was determined to NOT use Leopard.
A few days later I looked at the Leopard disk and found that rings had been "scratched" or "worn" into the data surface as though my DVD reader/player had malfunctioned and been in contact with the disk surface. I was horrified and quickly looked at all my other program disks just used for the reinstallations, afraid the DVD player had ruined them too. They were all ok. This lead me to believe that perhaps the Leopard disk was bad even before I put it in my computer. I called Apple. They issued a new disk with barely a comment.
Well, I finally got around to doing an install of Leopard with the new DVD. I looked carefully at the disk first. No apparent ring scratches. The install worked--really slowly--but it finished and works fine.
However, when I ejected the disk, I took a look and, sure enough...the data side had rings scratched (or worn) into it as though my DVD player had been in contact during the installation process! They were not there before the install. This has NEVER happened with any of the other MANY installation disks (or disks I've burned) on this computer but has now occured TWICE with the Leopard install disk!!!! WHAT'S GOING ON?????
Has anyone else seen this issue?
You might see what happens if you play a movie DVD. Use an old one. Be sure to play it through the switch point to the second layer.
You problem may be that optical drive is damaging dual-layer DVDs for some obscure reason.
Most of the other installation disks you used were probably single-layer disks.
It might also be that the Leopard DVD is a bit thicker than a standard DVD. Check the thickness.
If you do get another replacement DVD I suggest making a backup immediately.
You might also be able to copy the scratched DVD on another machine, but it has to had a DL burner. Sometimes copying a scratched DVD will work, since the copying process re-reads bad areas many times.
If you do get another DVD, use an external drive until you are sure why this is happening.

Why does my computer keep ejecting the snow leopard install disk

I am trying to upgrade from leopard to snow leopard on my MacBook Pro. However, every time I insert the install disk, the machine whirs for a moment, and then ejects the disk with no error message. I tested my drive with a different dvd and it works just fine. All of my other software is up to date. Any idea what could be causing this or what I can do?

Susan Rule wrote:
I am trying to upgrade from leopard to snow leopard on my MacBook Pro. However, every time I insert the install disk, the machine whirs for a moment, and then ejects the disk with no error message. I tested my drive with a different dvd and it works just fine. All of my other software is up to date. Any idea what could be causing this or what I can do?
Clean the bottom of the disk with a bit of rubbing alcohol and a soft cloth, polish to a shine.
If it's a PowerPC Mac it won't upgrade.
Must be a 10.6.3 Snow Leopard retail disk (white with cat like my avatar)
Try holding the c key down with the disk inserted and then reboot.
If all that fails, the disk is likely bad. It happens.
You can chose to copy it and hope the errors get fixed or exchange it for another with Apple.
Insert your Snow Leopard DVD.
Open /Applications/Utilities/Disk Utility.app.
In the left side of the window, select the “Mac OS X Install DVD”.
Click “New Image” from the Disk Utility toolbar and select where you want to save the temporary image. For “Image Format”, choose “DVD/CD master” and for “Encryption”, choose “none”.
The image extension in the “Save As” box will be .cdr (this is what you want) — click “Save”.
Once the temporary image is created, it will show up on the left side of the Disk Utility window. Select it.
Insert a blank dual-layer DVD
Click “Burn” from the Disk Utility toolbar.

I'm having problems installing disk 2 of oracle 9iAS linux edition

I'm having problems installing disk 2 of oracle 9ias linux edition is thier anyone else having this same problem

Is it original media? The first installation disk set i received from oracle had a bad disk 2. Once I received the new set, everything was fine. You may have bad media as well.

Bad Install Disk

Similar Messages

Maybe you are looking for