Bad sound after updating

Bad sound after updating

Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Check your settings. The iPads have a small switch on the right edge. It can be used as a rotation lock to keep the screen from automatically reorienting itself as you move around, but you need to have the tablet’s settings configured properly. That same switch, right above the volume buttons, can also be set to function instead as a mute button to silence certain types of audio.
If the switch is set to work as a mute button, you can change its purpose to “screen-rotation lock” by tapping the Settings icon on the home screen. On the Settings screen, tap General on the left side, and on the right side of the screen flick down to “Use Side Switch to.” Tap to select Lock Rotation or Mute to set the button’s function. Even if you set the side switch for your preferred use, you can still mute the Mini or lock the screen. Just double-click the Home button, and when the panel of apps appears along the bottom edge of the screen, flick the row from left to right with your finger. Tap the icon on the far left side of the row to either lock the iPad’s screen or mute the iPad’s alerts, notifications and sound effects. Music, podcasts and video are not muted unless you turn the volume all the way down.
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/ts5180
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/ts1630
http://www.atreks.com/app-no-sound-on-ipad-4-%E2%80%93-what-to-do/
To solve some sound problems, just follow these simple steps
1. Go to Settings
2. Tap on General
3. Tap on Reset
4. Tap on Reset All Settings
 Cheers, Tom

Similar Messages

  • HT4623 My iPad 3 has lost the speaker sound after updating to iOS 6.1, headphones are working fine

    My iPad 3 has lost the speaker sound after updating to iOS 6.1, headphones are working fine. Please help me out, done all the troubleshooting like restarting, side switcing, cleeaning the headphone jack etc.,

    Hi I also have this problem. Sound was only working on the headphones and also on the volume slider in the settings app. Everywhere else I get no sound and no volume slider. Now the headphones don't work either.
    (I'm using an ipad 2 iOS 6.1.2) 
    And NO it's not muted. I've reset all settings and restarted the iPad. Been searching forums for a couple days. Some say its a dirty docking port problem, others suggest a Skype or other app update that could be the problem.
    No volume control icon appears when I press the volume control buttons. Only says sound effects, if it says anything at all. Most often there is NO volume icon. YouTube, video, music, and other game apps, no sound.

  • Poor sound after updating to ISO 7

    Poor sound after updating to ISO 7. Before updating i had terrific sound both on my music and videos I recorded with my cam, i had to turn it down. Now, after update, i put volym on Max and can hardly hear the music or whatever. Anyone else with same problem?

    I also loved my iphone because it HAD great sound.  Since the update of the iso7 for my iphone 4s, i am missing my calls because I cannot hear the phone ringing.  The sound is so low even though I have it on the highest sound possible.  The is something in the update that caused this problem among others such as the phone blinking out while I am viewing videos.  Help Apple!  THe battery is going from 100 percent to 20 percent in two hours even when I have almost turned off everything on my iphone.  I need my sound back!  Apple please find out what happened in your update that caused the loss of the sound!

  • Why my iPad mini 2 no sound after updated to iOS8

    Why my iPad mini with retina display no sound after updated to iOS8

    I solved for my ipad mini retina:
    - Go to Settings->General
    - Change the function of the slider on the side of the ipad from 'rotation lock' to 'sound off'
    - Wiggle the slider up and down
    - Sound is restored
    - You can set the slider back to rotation lock again

  • Lost sound after update to 10.7.3 my recent mbp i7 ivybridge 13.3 mid 2012

    please help me quickly ...i lost sound after update to 10.7.5my recent mbp i7 ivybridge 13.3 mid 2012
    i also tried re installing 10.7.3  and finally 10.8 also lost sound
    but when i boot to windows 7 the sound works fine in windows and dissappear again in mac os
    what can i do ???????
    macbook pro core i7 ivybridge 13.3 mid 2012

    The service centre told me it will need changing the logic board

  • Distorted sound after updating from iTunes 10.4 to 10.5 in Win XP SP3

    After the latest Apple update,I have  istorted sound after updating from iTunes 10.4 to 10.5 in Win XP SP3.
    But it plays normally sounds coming from my connected iPod or any internet radio station !!
    If I add any song to a playlist, it turns out to be just noise!
    Any clue ?
    Thanks for any help !
    LAO

    I recieved the same message. Have you found a fix to this?
    If not, read my issue because I belive we have the same
    https://discussions.apple.com/thread/3442836
    It would be nice to work this out with another person.

  • Problem with sound after update

    Hello
    After update to 11.3 I have no bass sound in subwoofer in Firefox browser (youtube). I uninstall the newest version and install previous (11.2) and bass plays ok.
    My os: Windows 7 x64. Sound card Creative X-fi.

    Hello!
    My problem is summed up in this topic.
    Updated Flash Player with 11.3 this morning (june 12th 2012) and since then my 7.1 Sound System works only 2.1. If i enable EAX Effects, works on 7.1 but since it`s just a room it sounds very odd.
    I have no problem with sound on HTML 5 websites for that matter, Winamp, Video Players, games.
    Uninstalled Flash Player, sounds work ok without it on different browsers, other than Chrome (since it has FP built in).
    I hope for a sollution soon.
    Thank you.
    *edit*
    Untill there is a permanent solution, i found a way to deal with my issue and i hope it will help others.
    I personally use Chrome and this is for this browser:
    1. Type "about:plugins" w/o the quotation in the navigation bar.
    2. On the upper right u will see "Details" click it then find the word "flash", and you will see something like this:
    Flash (3 files) - Version: 11,3,300,257
    Shockwave Flash 11.3 r300
    Name: Shockwave Flash
    Description: Shockwave Flash 11.3 r300
    Version: 11,3,300,257
    3. I say again, this worked for me on Chrome. The 3 files i have, two of them are Version 11,3,300,257 and one is 11.2.31.144
    4. Simply disable the lates version 11.3 and enable the previous version 11.2
    I hope this helps.
    Message was edited by: AndrewPAM

  • I have no sound after updating to iOS 6.1.3

    After updating I lost sound. Tried restoring and still no sound. Guess I'll have to get a new phone...any other suggestions?

    Check out my post I spent 15 hours fixing it when my iPad 2 on iOS 6.1.3 volume disappeared.
    https://discussions.apple.com/thread/5075175

  • Multiple message sounds after updating iOS 5

    After updating my iphone 4 to iOS 5, Whenever i get a msg or a notification, the tri-tone message sound is played about 3 times. Am i the only one?

    If you mean that the tri-tone sound is repeated with intervals of two minutes: When you go to Settings -> Notifications -> Messages, near the bottom you can choose how often a message alert must be repeated. This can be set to never.

  • No sound after updating to 10.7.3 - no boot camp available

    All sounds gone after updating to 10.7.3
    tried to reset NVRAM + PRAM via pressing (cmd)+(alt)+(p)+(r) while starting - this was not helping.
    Found also the thread below, but i have no boot camp available
    https://discussions.apple.com/message/17477460
    All ideas welcome----

    You should correct the model of mac, cannot be PowerBook, perhaps MacBook or MacBook Pro.
    I have read that many people have had problems after last update, here all is fine. The only idea I have is to download from Apple site the combo update (the bigger update), and re-run it. This often solves issues.
    As about BC, can you see that partition in Disk Utility? If yes, open Finder preferences, do setttings look like here?

  • No windows sound after updating the IDT High definition Codec!! HELP!!!

    Hi all
    I really need ur help now
    I have updated IDT High Definitio Audio Codec several days ago
    after i reboot my notebook, I couldn't hear my windows sound anymore
    than i reboot till 2 times, n the windows sounds was heard again
    However, after I turn it on the next day, i found that i have no windows sounds again
    but i can play media players, such as winamp, n could hear msn sound
    After i reboot my PC, the sound was heard. But after turning it on for the 2nd times, i couldn't hear the windows sound again!!!
    Help me please
    How could I fix this?
    I have rollback driver, but i doesn't work. Coz before updating IDT audio by windows update, I have updated IDT audio through HP support assistant
    N i am a little bit afraid of doing system restore...
    PLEASE HELP ME
    THX

    Hi,
    Download correct audio driver.
    How to find it on HP sites?
    1. Click on Support & Drivers link. (Upper part of this page.)
    2. Choose option: Download drivers and software (and firmware)
    3. In form:
           Enter a product name / number
           For product provide Your p/n. (How to find correct p/n informations here.)
    4. Click on Go and choose system which You are using now.
    Disconnect from Internet.
    Uninstall from Your system IDT audio drivers.
    Resources:
    Uninstalling Software in Windows 7
    Uninstall or change a program in Windows 7
    Restart Your system:
    On boot press ' F8 ' and choose ' Safe mode '.
    Go to Control Panel -> Devices Manager -> Audio, Video and Games Controllers 
    and find there Audio card. Click on it with right button of Your mouse and choose uninstall driver.
    Restart Your system and this time start it in normally.
    Install this driver which You downloaded.
    ** Say thanks by clicking the "Thumb up" icon which is on the left. **
    ** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

  • [solved] gnome-shell bad looking after update

    Hi,
    After update (about two weeks ago) my gnome looks bad. You can see this in screenshots. Very large icons and strange rectangles in gnome shell menu on started applications.
    Can you help?
    Last edited by skoczo (2015-05-01 17:27:23)

    eyemonen wrote:
    Hi
    Desktop icons: open Files (nautilus) and change default zoom level for icons from standard to small (preferences - views).
    Rectangles:  this is how running applications are displayed in the default theme. If those rectangles bother you too much, the easiest way is to change theme. For example, ceti-2 and vertex are already ported to 3.16.
    It works. Thanks for help.

  • Problem with sound after updating to ios 7.0.6

    Help!
    No sound whatsoever from the speaker after updating to ios 7.0.6.
    Sound from earplugs & through dock OK.
    I tried everything I found on the web, but nothing worked up till now.
    Tips, anybody?

    Hi singsingsarah,
    Thanks for visiting Apple Support Communities.
    Be sure to try all of these steps if you do not hear sound from your iPhone speakers:
    If you do not hear sound from the built in speaker, try these steps:
    Verify that the volume is set to a level you would normally be able to hear.
    Ensure that there is nothing plugged in to the headset jack or the dock connector.
    If the iPhone is in a protective case, make sure that the speaker port isn't blocked by the case.
    Make sure that the speaker and dock port aren't clogged with debris. If necessary, clean it with a clean, small, dry, soft-bristled brush. Carefully and gently brush away any debris.
    If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
    If the iPhone is paired with a Bluetooth headset or car kit:
    Try turning off Bluetooth.
    If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
    Restart the iPhone.
    If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
    If the issue is not resolved after restoring the iPhone software, please contact Apple Support.
    You can find the article with these steps here:
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/ts5180
    Best,
    Jeremy

  • I DO NOT SOUND AFTER UPDATE OF WINDOWS 8.1 UPDATE

    HI IM HAVING PROBLEMS WITH THE SOUND ON MY COMPUTER AFTER UPDATING WINDOWS 8.1 CAN U PLEASE ASSIST ME

    Hi,
    Can you post back with the full Model No. and Product No. of your notebook - see Here for a guide on locating this information.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • HT4623 my i phone4 lost sound after update

    no sound on my i phoe 4 after update!

    The service centre told me it will need changing the logic board

Maybe you are looking for

  • Forcing Creation of Target Field

    Hi, I want 2 force the creation of target field C in my Message Mapping.: So, if A exist and not empty, map A to C, if not, map B to C. The problem is, if i have a not existing field on left side, the right side wont be created. But I want C to be cr

  • Generate Report for each value of a certain column in a different pdf file

    Hi, I am generating a Group Above report in Oracle Reports Builder 10g. The scenario is that this report needs to be generated for several branches of a bank. The report needs to get generated in a different pdf file for each branch. The report, I ha

  • Empty iviews in MSS ERP 2005

    Hi, We've installed the above business package.  When we click through the iviews, a lot of them are coming up empty.  For example the following iviews under Overview -> Team -> Employee Information are empty: 1) General Information 2) Compensation I

  • Cannot find server - iweb

    I am new to iweb but was able to create and publish a site. All was well, people viewed it. My husband changed what was called "Site2" on the site to our family name. Once he published, you can no longer connect to the site. I click to "announce" the

  • How to build CIFs in SCM

    Hi,       Can any one give me a step by step solution to extract data from SAP to APO and some insight into build CIFS. Thanks