Badly needed help!!!!!my iphone 3 is in recovery mode...

help how can i fix my iphone 3 ....
my iphone is is in recovery mode right now
i dont know how to fix it everytime i try to restore it
there is 1015 error that always appear help pls......
if anyone know how to fix it pls teach me how plssssssssssssss....

Error 1015 occurs when trying to restore a previously jailbroken phone. By jailbreaking your phone, you have voided any warranty, and also eliminated the possibility that you can get help from Apple or it's forums. Terms of use prohibit the discussion of jailbroken phones here.
You will need to scour the internet for a solution to your problem. Be aware, however, that it is very likely you may never get your phone working again.
Best of luck.

Similar Messages

Pls.help my iphone stuck in recovery mode and itunes wont recognize it..i tried the other options that posted here,,,pls tell me what to do..

pls. help my iPhone stuck in recovery mode and iTunes wont recognize it..i tried the other options that posted here,,,pls tell me what to do..before it was just stuck in an apple logo but when i tried recovery mode to itunes then it stuck..

Hi awison,
If your iPhone is not recognized by iTunes on your Windows computer you may want to use the steps in this article to troubleshoot -
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
This may also resolve your recovery mode issue. If it does not, use the steps in this article to resolve it -
Use iTunes to restore your iOS device to factory settings
http://support.apple.com/kb/HT1414
Thanks for using Apple Support Communities.
Best,
Brett L

TS1363 i need help to get out of recovery mode

i need help to get out of recovery mode

To get the phone out of recovery mode you will need to connect it to a computer with iTunes installed on it and restore it.

Please help! iPhone gone into recovery mode

Hoping someone can help me, getting worried!! I just plugged my iPhone 4s into my Windows computer to update and sync etc as I hadn't for a while. During the updating and backup process, my phone just went into recovery mode, it disappeared from the devices menu and a message box came up saying 'iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes.' My phone screen is stuck on the iTunes logo with the usb picture. I have tried restarting my computer, holding down both buttons on the phone etc but it just stays the same....any advice would be greatly appreciated!!!

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...

HELP PLEASE :( IPHONE STUCK IN RECOVERY MODE.

Hey so this is the story.
i wanted to update to ios4.1 so it said i needed to restore
so i did and then it gave me error codes (1004). It would not let me restore and update. so now i am stuck in recovery mode.
i really need help please. i have tried irecovery but no luck.
someone please help my iphone is a must have. i need it tomorrow.
i have
Windows7 64bit
iPhone4
please someone help.

Doing a search on Google revealed this:
if you ever edited your hosts file ...change it back. basically do the reverse of this to about step 5:
mac
http://www.iclarified.com/entry/index.php?enid=7556
windows
http://www.iclarified.com/entry/index.php?enid=7557
(editing the file back to the original worked for me)
Follow those instructions and see if that helps.

Help, my iphone is in recovery mode, and itunes shows error code 1

help me, please. my iphone 4 is stuck in recovery mode, and when trying to restore, itunes shows " error code 1, an unknown error occurred"
please help!!!

me to ;/
[23:05:36.0982] [nand_part_core:INF@2289] first 2 pages of boot blocks written with copies of partition table
[23:05:36.0982] [nand_part_core:INF@3169] next 98 pages of boot blocks written with LLB image of size 150080 bytes
[23:05:36.0982] [nand_part_core:INF@3172] final 156 pages of boot blocks written with random data in full page format
[23:05:36.0982] entering update_gas_gauge
[23:05:36.0982] entering update_ir_mcu
[23:05:36.0982] looking for mcu nub...no entry from path!
[23:05:36.0982] TiSerialFlasher not supported on this platform. Exiting.
[23:05:36.0982] entering update_baseband
[23:05:36.0982] update_baseband: registering for progress notifications
[23:05:36.0982] create_baseband_update_options: Got imeisv: 16
[23:05:36.0982] baseband updater options = <CFBasicHash 0x17533030 [0x59b710]>{type = mutable dict, count = 7,
[23:05:36.0982] entries =>
[23:05:36.0982]     0 : <CFString 0xcf1e38 [0x59b710]>{contents = "SystemRoot"} = <CFString 0x1761cb70 [0x59b710]>{contents = "/mnt1"}
[23:05:36.0982]     5 : <CFString 0xcf1dc8 [0x59b710]>{contents = "DisallowFusiing"} = <CFBoolean 0x59b910 [0x59b710]>{value = true}
[23:05:36.0982]     6 : <CFString 0xcf1f48 [0x59b710]>{contents = "autoSetupEnv"} = <CFBoolean 0x59b918 [0x59b710]>{value = false}
[23:05:36.0982]     7 : <CFString 0xcf1e48 [0x59b710]>{contents = "DataRoot"} = <CFString 0x1761e8e0 [0x59b710]>{contents = "/mnt2"}
[23:05:36.0982]     8 : <CFString 0xcf1d98 [0x59b710]>{contents = "forceUpdate"} = <CFBoolean 0x59b910 [0x59b710]>{value = true}
[23:05:36.0982]     9 : <CFString 0xcf1f58 [0x59b710]>{contents = "disablePing"} = <CFBoolean 0x59b910 [0x59b710]>{value = true}
[23:05:36.0982]     10 : <CFString 0xcf1eb8 [0x59b710]>{contents = "IMEISwVersion"} = <CFNumber 0x17533010 [0x59b710]>{value = +16, type = kCFNumberSInt32Type}
[23:05:36.0982] }
[23:05:36.0982] update_baseband: querying baseband info
[23:05:36.0982] bbupdater: BEGIN: Querying info at stage first
[23:05:36.0982] bbupdater:     BEGIN: Preparing first stage
[23:05:36.0982] bbupdater:         Requested boot mode: kBBUBootModeNone
[23:05:36.0982] bbupdater:         Creating transport, attempts remaining 5...bbupdater:         FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater:         powercycling modem
[23:05:36.0982] bbupdater:         Creating transport, attempts remaining 4...bbupdater:         FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater:         powercycling modem
[23:05:36.0982] bbupdater:         Creating transport, attempts remaining 3...bbupdater:         FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater:         powercycling modem
[23:05:36.0982] bbupdater:         Creating transport, attempts remaining 2...bbupdater:         FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater:         powercycling modem
[23:05:36.0982] bbupdater:         Creating transport, attempts remaining 1...bbupdater:         FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater:         powercycling modem
[23:05:36.0982] bbupdater:         Creating transport, attempts remaining 0...bbupdater:         FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater:     END(kBBUReturnIOError): Preparing first stage
[23:05:36.0982] bbupdater: END(kBBUReturnIOError): Querying info at stage first
[23:05:36.0982] send_bbupdate_status: sending baseband update status to host
[23:05:36.0982] update_baseband: calling CFNotificationCenterRemoveEveryObserver
[23:05:36.0982] update_baseband: bbupdater error: The operation couldn\U2019t be completed. (BBUpdater error 3 - Failed creating a communication transport to baseband.)
[23:05:36.0982] 0: RamrodErrorDomain/3ec: update_baseband: failed querying baseband info
[23:05:36.0982] 1: BBUpdater/3: Failed creating a communication transport to baseband.
[23:05:36.0982] unable to convert ramrod error 1004
[23:05:36.0982] restore failed with CFError:
[23:05:36.0982] 0: AMRestoreErrorDomain/ffffffff: failed to update device firmware
[23:05:36.0982] 1: AMRestoreErrorDomain/ffffffff: ramrod firmware update failed
[23:05:36.0982] 2: RamrodErrorDomain/3ec: update_baseband: failed querying baseband info
[23:05:36.0982] 3: BBUpdater/3: Failed creating a communication transport to baseband.
[23:05:36.0982] waiting for host to acknowledge final status received...
[23:05:36.0982] void AppleUSBDeviceMuxXXXXXXXXXXXXXXXXXXX(mbuf_t) received reset, closing 0x97b1e4d0
[23:05:36.0982] recv(12, 4) failed: connection closed
[23:05:36.0982] unable to read message size: -1
[23:05:36.0982] received NULL message from host, expected final status
[23:05:36.0982] attempting to dump restore log
[23:05:36.0982] writing log file: /mnt1/restore.log

Help! iPhone 4s in Recovery Mode after new IOS 7.1.1 update.

I went to update my iphone 4s earlier to IOS 7.1.1 and now it's in recovery mode. My issue with that is I keep trying to download the update on my computer so it can do the recovery and every time it gets to fully download (which bc I have a ****** internet company it takes hours to get there) I get an error message. IDK what else to do. Is there a way I can bypass the update and just run the recovery mode with the 7.1.0 update? I don't know what else to do. This is the first time I've had issues like this with this phone and I've had it over 3 years now.

Don't know if this will help but when I updated to 4.0.2 my phone gave me an error and bricked.
I made a new user on my computer, installed itunes and then was able to update my phone without it erroring. Once I had a working phone I went back to the old user and updated my phone with all of the information that was there before. I lost a few things but had a working phone.
Since then I have not had a problem with updating it in the old user. You might see if it will help with you all.
Message was edited by: Johnna Lynne

Need help with infinite loop in recovery mode in Creative Zen 20

hi,
I'm having this problem with my Creative Zen 20 GB:
When I turned it on, it goes immediately to the rescue/recovery mode. Not sure why. Will do that even when I reset the device.
So, I selected cleanup. After cleanup, it remained showing the menu of the recovery mode. I selected reboot. After reboot, it went back to the rescue/recovery mode. And it goes on and on like an infinite loop.
Finally, I decided to do a formatAll. Again, it remained in the recovery mode menu after the formatAll action. After reboot, it again went back to the rescue/recovery mode.
I have never updated the firmware. So, I thought maybe that will help. However, when I connected the device to my PC, the device went to rescue/recovery mode and the PC could not detect the device connected via USB. In short, I am currently not able to do anything at all with the device except charging it.
Would appreciate help/advise.
Tks in advance.

huggiebear wrote:
I connected the device to the PC and after the PC tried to load the library, it said "Player is not connected".
What library are you loading? After you have run that reload os option, you need to connect the player to the computer and run the firmware update software. If you haven't download that, you can go to the download section and download it. If all else fail, the player is probably faulty and you would need to get in contact with Customer Support then.
Jason

Hi, my iphone its in recovery mode and when i restore my iphone 5s loading show the blue screen and show note on itunes (unknown error 14) please i need your help please . thanks

Hi, my iphone its in recovery mode and when i restore my iphone 5s loading show the blue screen and show note on itunes (unknown error 14) please i need your help please . thanks

In the article Resolve iOS update and restore errors this is what it says about error 14:
Check your USB connections
Related errors: 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650, 2000, 2001, 2002, 2005, 2006, 2009, 4005, 4013, 4014, or “invalid response."
If the USB connection between your device and computer is interrupted, you may be unable to update or restore.
To narrow down the issue, you can also change up your hardware:
Use the USB cable that came with your device, or a different Apple USB cable.
Plug your cable into a different USB port directly on your computer. Don't plug it into your keyboard.
Try a different computer.
If necessary, resolve any further issues with the USB connection, then with your security software.
If you're still seeing the error message, check for hardware issues by following the next section.

My iphone4 has been stuck on the connect to itunes logo for a few hours.I connect it to itunes and it says that the iphone is on recovery mode and that I need to restore it to use it with itunes.I'm afraid that if I restore it I will loose everything help

My iphone4 has been stuck on the connect to itunes logo for a few hours. I connected it to itunes and it says that the iphone is on recovery mode and that I need to restore it to use it with itunes. I'm afraid that if I restore it I will loose everything help please!!

AT this point whatever data you have on yoru phone is already gone since it is in recovery mode.
However you can restore from your backup, when your phone reboots from recovery.
YOu do have a backup right?

HT5654 MY IPHONE IS IN RECOVERY MODE I NEED HELP TURNING IT BACK ON

my iphone is in recovery mode. the screen has the itunes icon and a USB picture with an arrow pointing up! i can not access my phone at all! i tried to turn it off and back on. nothing. what options do i have and how do i fix this?

Do as the image on the screen suggests.
Connect the device to a computer running iTunes and restore.

My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

HELP! iPhone went into Recovery but I can't Restore - no space!!!

I was trying to update my phone but in the middle of the update, everything froze. Now my iphone is in recovery mode, and I can't do anything through iTunes because it's telling me that I don't have enough space on my storage disk. HELP ME!!!!!!!!!!! I don't want to lose all my texts and photos!!!!!!!

Then you need to Free up some Space on your Computers Hard Drive.
Freeing Up Disc Space
what-to-do-when-your-hard-drive-is-full.html
Note: It is both Prudent and Recommended to have at least 15 to 20 GB of available Space on your Hard Drive for your Mac OS X to perform as expected.

HT4528 i need help unlocking iphone

can anyone help me unlock my iphone

If you mean your passcode lock:
Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
1. iOS- Forgotten passcode or device disabled after entering wrong passcode
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. Restoring iPod touch after forgotten passcode
4. What to Do If You've Forgotten Your iPhone's Passcode
5. iOS- Understanding passcodes
6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
Forgotten Restrictions Passcode Help
iPad,iPod,iPod Touch Recovery Mode
You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
You can restore from a backup if you have one from BEFORE you set the restrictions passcode.
Also, see iTunes- Restoring iOS software.
If you mean unlock from your cellular provider, then contact them. They are the only one who can unlock the phone.

HT201210 My iphone is in recovery mode and it won't open help

I tried to install the new version of iOS via itunes and at the end of the installing it stopped and showed an error massage says "iphone couldnt be stored error (14)" and now my iphone is in recovery mode I tried to open it with DFU mode but it didnt work out HELP

What "new version" of iOS did you attempt to install, exactly?
Here is troubleshooting information specifically for the error 14 you mentioned: http://support.apple.com/kb/ts3694#error14
Error 13, 14, 35 and 50 (or -50)
These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.

Hi.I need help.my iphone was Stolen .how can I get back my iphone. Serial No.DX*****PMW.could you help me find my iphone.thank you very much.could you send me the ICCID number to help me find the iphone

Hi.I need help.my iphone was Stolen .how can I get back my iphone. Serial No.DX******PMW.could you help me find my iphone.thank you very much.could you send me the ICCID number to help me find the iphone.if you can help me.
<Personal Information Edited by Host>
Sincerely a Chinese girl really need your help

Sorry we are all users on this User Community No Apple Staff
Read this .
http://support.apple.com/kb/HT2526
Apple do not and cannot assist in finding stolen property ,that is the responsility of your Police

Badly needed help!!!!!my iphone 3 is in recovery mode...

Similar Messages

Maybe you are looking for