Bandwidth command in 3500Xl switches

Hi,
I have seen a bandwidth command in the interface config mode. When I apply it, it does not limit the traffic.
I have to limit a traffic on a perticular port to which a PC is connected.
THanx
sagar

Hi,
thanx for ur reply. I tried for policing the traffic.
I created a class-map, then applied that class to the policy map. But when I try to apply the policy to the interface, there is no effect of the command nor does the applied command shows up in the show run.
The config is as given below:-
class-map limit
match access-group 2
policy-map rate
class limit
bandwidth 100
access-list 2 permit 10.3.22.204
Switch(config)#int f0/15
Switch(config-if)#service-policy input rate
The last command is not reflected in the sh run
sagar

Similar Messages

How can I encrypt my data links between switch uplink ports ? I'm unable to use "cts Manual" command in C3560X switch.suggest me

How can I encrypt my data uplinks between switch trunk ports ? I'm unable to use "cts Manual" command in C3560X switch.suggest me as I want to encrypt my switch-to-switch link with Cisco TrustSec.

Hi
Login to switch & go to interface..
There you can give tags.. (ISL & DONT1Q)
Command switch-port mode trunk
Switch-port trunk encapsulation ssl or dot1Q

How to add the IP address helper command to the switch

Hi
I am trouble shooting a SF 200-48P and I am a bit lost without a CLI not used to the GUI. What I need to know is how to add the IP address helper command to the switch?
I have a number of IP phones which are not getting an IP address from DHCP (PCs which are diasy chained off the phones are all working correctly). On the higher end switches I would have added the IP address helper command to the VLAN and that would have sorted it. However I can't seem to figure out how to do this on the small business switch.
Thanks
Lorne

Thanks Rizwan. I was banging my head wishing they weren't small business switches as I felt lost without the command line!
Lorne Gallagher | McCann FitzGerald Solicitors | Riverside One, Sir John Rogerson's Quay, Dublin 2, Ireland | DDI +353 1 607 1726 | Fax +353 1 829 0010 | www.mccannfitzgerald.ie
Ireland Law Firm of the Year 2011 | Chambers Europe
Ireland Law Firm of the Year 2011 | International Financial Law Review

What's "SAVE" configuration command for Cisco switch/ router?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well,
but so long, any other command that easy to remenber?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well, but so long,
any other command that easy to remenber?
yes, here: Switch#write,and want to know more about the Cisco switch, please visit:http://www.3anetwork.com/cisco-switches-price_c1

Router "snmp-server contact" command for catalyst switches??

From the router you can configure the "snmp-server contact <text>" command
to set the system contact for SNMP. Is there any equivalent command for
Catalyst switches? I know that there's a "set system contact" command for
CatOS but i'm sure if it has something to do with SNMP.
Thanks in advance.

Yes, set system contact on switch is the same that on the router for the above command. Once you use this this command to enter the contact info, it can be polled via the SNMP MIB Object sysContact (.1.3.6.1.2.1.1.4) from RFC1213-MIB. Example, if I use 'set system contact foo', I see the following using the 'show system' output:
System Name System Location System Contact CC
foo
Polling the above via the above MIB object on the switch:
% snmpwalk .1.3.6.1.2.1.1.4
system.sysContact.0 = foo
Similarly, if you set the 'System Name' on the switch using the command 'set system name ', can be polled via sysName (.1.3.6.1.2.1.1.5) from RFC1213-MIB
Lastly, 'set system location ', once set can be polled via sysLocation (.1.3.6.1.2.1.1.6) from RFC1213-MIB

Bandwidth command

"Router (config) #bandwidth <value>" This command set bandwidth value for an interface. Is this correct command? Should this issue in interface config mode or global mode? Can bandwidth command use to limit the bandwidth of an interface? What is the default bandwidth for interfaces? Unlimited? Will this command works with sub-interface too?

The bandwidth command is applicable only to interfaces, not the global level. It is used to determine the link cost for link-state protocols, among other things. It does not affect the actual bandwidth of the interface. And it certainly does work with sub-interfaces.
Paresh

Switch command of 2960 switches

I have 1 switch 2960 24TC S. i updated the iOS to 15.0.2 . i want to configuration with the command:
authentication event server dead action reintialize vlan
but the command of the switch show me i can only configure: event fail or non-response
i read some article that this switch do support the command: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/15-0_1_se/command/reference/cr_2960/cli1.html
Any idea for fix it ?

I think the actual deployed number is coming out to 6, but with this customer, you never can tell. :)
I came in to this well after the architecture was planned and sold to the customer, now it is just a matter of making it work.
It should not be too bad, considering the stacks are backed by 10gb uplinks to the core and the port-channels are to bond the ports to the workstations, so at least we are not hanging more switching off of them.
Thanks for the info,

Command-Tab App Switcher doesn't work (related to corrupt .plist file error?)

Hi folks,
The other day, Drive Genius 4 reported on a file corruption: ~/Library/Preferences/System Mac.plist file. I tried to find the file but it didn't appear to exist.
Today, a strange phenomenon occurred which I think may be related. Strangest thing. I was using Safari, had several tabs open when, suddenly, I lost all input to any links in Safari and system wide as well, other than the cursor being able to move around the display. This dysfunction also included the Command-Tab App Switcher, though they keyboard text function still worked. I could enter text in fields.
I tried Force Quit Apps but I had to shutdown and reboot using the Power button. The reboot seemed to remedy the situation and most controls and keyboard functions returned except for the Command-Tab App Switcher.
In Safari, I used History/Restore Last Open Page, and when the searched for pages came up, they were blank - I was informed that there was no internet connection. Wi-Fi showed still on but grayed out, which could be logical. Also, this is when I noticed that the key repeat function wasn’t working. In System Prefs, I did manage to change the key repeat rate, which accelerates the backspace erase function but there is no key repeat, itself.
All of this, of course, might be pointing to that system file error. Whether it is that hidden Mac.plist file corruption I don’t know.
In any event, first thing I did was to run Permissions Repair. At one point, about 2/3rds of the way in, the progress bar hung for a few minutes and then finished the last third in a split second. In the Repair Permissions log there was no /Mac.plist file among those repaired.
Additionally in Sys Prefs, I tested for Tab key response by refocusing the radio buttons in the Full Keyboard Access option under Keyboard/Shortcuts panel from "Text boxes and lists only" to "All controls.” The refocus worked because now pressing Tab does move the cursor through every control. But still no Command-Tab App Switcher. In Spotlight, I did find the App Switcher.app but it would not open, because it is “Damaged or Missing.” App Switcher preferences are also not accessible.
In Terminal I changed directories and do see the /Mac.plist file under discussion. I suppose I could -rm the file but I’m reluctant without knowing more about what other anomalies might result. The App Switcher is one of the Mac’s best utilities (thanks to er, Microsoft.) If the /Mac.plist file will refresh from the current status, no problem, I would think.
Has anyone experienced anything like this? Any suggestions? Thanks a whole lot in advance for your time and consideration in this!
All best,
David

First, get rid of the worthless, time-wasting "Drive Genius" according to its developer's instructions. Never install any so-called "utility" again.
Don't waste time repairing permissions again, either, unless you have an indication of a permission error involving system files, which you don't and probably never will.
Never delete any file in the shell (Terminal) for any reason.
There is no built-in application called "App Switcher." There is no built-in file named "System Mac.plist" either.
If command-tab application switching still doesn't work after you get rid of "Drive Genius," see below.
Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

Trunking on older 3500XL switches

I probably already know the answer to this but is there a way to remove vlans 1 and 1002-1005 on a trunk port on a 3548-XL? I want to be able to connect an IP phone to the port and only allow traffic from my voice and the floor vlans (599 & 730) respectively. But when I run the command:
switchport trunk allowed vlan remove 1-598,600-729,731-1024
all the vlans are removed exept 1,599,730,1002-1005. I know that these are "special" vlans and these are older switches, but is there a way to remove them from a port on these switches?

If you want to configure the port for just voice vlan and data vlan then you need not to clear vlans out of the trunk, just configure voice vlan. This platform should support voice vlan. for example:
interface FastEthernet0/2
description DOT1Q port to IP Phone
switchport trunk encapsulation dot1q
switchport trunk native vlan 730
switchport mode trunk
switchport voice vlan 599
spanning-tree portfast
For more information:
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00800ffdcc.shtml#vlanscat3500
From 3500XL port configurations guide:
http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/29_35wc6/scg/swports.htm#xtocid32
Please rate helpful posts.

Command ~ (tilde) to switch windows stops working

Well, actually I guess it is command-` since you don't press shift.
My problem is this command key short cut stopped working. Mac OS 10.4.11 onAlu iMac with 4gb ram. It had been working, but now I noticed it stopped working.
It never worked on my G4 tower but did work on my wifes iBook. It didn't work in my buddies tower but does work on my dads iMac G5.
What the heck? How does a command key shortcut stop working. I get a audible bonk alert when I try to do command-` to switch windows. It used to work.
Any ideas?
Message was edited by: David Cretney

Have you checked your keybindings? +(System Preferences > Keyboard & Mouse > Keyboard Shortcuts)+ Is there a checkmark next to "Move focus to next window in active application"? Maybe your modifier keys have been altered? +(System Preferences > Keyboard & Mouse > Keyboard > Modifier Keys...)+

"ip routing" command on SG300 switch

What does "ip routing" do on the CLI on the SG300?
When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it.
I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
Thanks,
scott

Ah, ok, thanks. I guess that was pretty obvious, now that I know the answer.
The "ip routing" command isn't mentioned anywhere in the CLI documentation, but I guess if I'd thought about it a little longer, I may have come to the same conclusion.
Thanks Tom.

How to enable Command-Tab to switch applications

I just upgraded to Lion from Snow Leopard in my iMac, but for some reason Command-Tab is not working.
I already restarted the computer and checked the option (it was already checked) System Preferences / Mission Control and tick "When switching to an application ...", but still not working.
What can I do ?

There is nothing to enable. The option you checked has nothing to do with the application switcher.
You could look through the keyboard shortcuts and see if anything has hijacked that shortcut.
Try starting up holding down the shift key. That will start up in safe mode and disable any third-party programs that might be affecting it. It also does a disk check, so it takes some time. See if it works in safe mode. If so, try restarting normally and see if it still works.
If it works in safe mode, then it is likely you have something that is interfering with it.
As another troubleshooting step is to log in as another user. If it works there, then you have something in your particular user setup that is causing the problem. If it doesn't work, then it is a system-wide problem.

"ARP time-out" command on Catalyst Switches

Hopefully this would help to all of you that have packet loss or TCP retransmissions, due to the fact that the ARP timeout is an absolute timer and not an activity timer like the MAC Address Table Aging Time.
This is an expected behavior in this type of switches (3750X). When we generate an ARP entry in software, that entry gets programmed into hardware and is not touched again until it is time for a refresh. The refresh happens 1 minute prior to expiration
Therefore, when trying to apply the "ARP timeout" command, be sure to use a timer higher than 1 minute, in order to have, as told before, the 1-minute timer to refresh the ARP table.
Sadly, this is not a bug behavior or something like that, basically, that is how the protocol works.
Anyway, Thanks all for the attention given.

Hi,
I am currently using 12.2(58)SE2 on the 3560.
Cisco IOS Software, C3560 Software (C3560-IPSERVICESK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1)
I downgraded my IOS to check if it's still supported for the 3560 on 12.2(55)SE1 and it's not.
XXX uptime is 1 minute
System returned to ROM by power-on
System restarted at 14:38:50 GMT Tue Jul 29 2014
System image file is "flash:/c3560-ipservicesk9-mz.122-55.SE1.bin"
XXX(config)#ip ssh ?
authentication-retries Specify number of authentication retries
dscp                    IP DSCP value for SSH traffic
logging                 Configure logging for SSH
precedence              IP Precedence value for SSH traffic
source-interface        Specify interface for source address in SSH
                          connections
time-out                Specify SSH time-out interval
version                 Specify protocol version supported
XXX(config)#ip ssh
I then upgraded to 12.2(55)SE9 and it's still not supported.
XXX uptime is 1 minute
System returned to ROM by power-on
System restarted at 14:47:49 GMT Tue Jul 29 2014
System image file is "flash:/c3560-ipservicesk9-mz.122-55.SE9.bin"
XXX(config)#ip ssh ?
authentication-retries Specify number of authentication retries
dscp                    IP DSCP value for SSH traffic
logging                 Configure logging for SSH
precedence              IP Precedence value for SSH traffic
source-interface        Specify interface for source address in SSH
                          connections
time-out                Specify SSH time-out interval
version                 Specify protocol version supported
XXX(config)#ip ssh
I would recommend that you upgrade but I don't see any point unfortunately.
Thanks,
Nehmaan

Which object in RSVP message carried the value configured by "tunnel mpls traffic-eng bandwidth" command?

Hi Experts,
I configured a simple MPLS TE tunnel in my routers and configured it with "tunnel mpls traffic-eng bandwidth 777" command. The tunnel came up fine. I tried to capture the packets (using GNS capture) going out of tunnel head end interface but I could not find out on which message object the value '777' is carried. Can anyone please explain me exactly in which RSVP/OSPF message the bandwidth value is carried?
Thanks,
Madhu

Hello Madhu,
I think it is FLOWSPEC object, not 100% sure
The FLOWSPEC class is defined in RFC 2210. Cisco IOS Software requests Controlled-Load service when reserving a TE tunnel. The FLOWSPEC format is complex and has many things in it that RSVP for MPLS TE doesn't use.The FLOWSPEC is used in Resv messages—Resv, ResvTear, ResvErr, ResvConf, ResvTearConf. Its only use in MPLS TE is to use the average rate section of the FLOWSPEC to specify the bandwidth desired, in bytes. Not bits. Bytes. So if you configure a tunnel with tunnel mpls traffic-eng 100000 to request 100 Mbps of bandwidth, this gets signalled as 12,500,000 bytes per second (100 Mb is 100,000 Kb is 100,000,000 bits, which is 12,500,000 bytes).
Hope this helps
Regards
Mahesh

Sendmail command on Content Switch.

I want to get e-mail alert's from my content switch. I was going to use the logging sendmail "e-mail address" "IP of SMTP host" command by what IP address will the switch use for outgoing mail use?

The second parameter "IP of SMTP host" is the address of an email server that will accept the SMTP connection. The subject of the email includes the management port's IP address. I don't use the management port so I set it something that helps me to identify the specific switch.

Bandwidth command in 3500Xl switches

Similar Messages

Maybe you are looking for