Bandwidth throughput Cisco 1800 Series

Hi All,
Currently looking at upgrading our 10mb leased line to 30mb. We currently have a a Cisco 1800 series which Cisco's technical manual says supports up to 40mb throughput, however our ISP are saying we should upgrade to a Cisco 1921 to support the additional bandwidth.. Has anyone run into this before? Any ideas if what our ISP are telling us is correct?
Thanks in advance,
J

Dear Joe,
Thank you for reaching the Small Business Support Community.
I am afraid you posted your comment, or request for comment, on the wrong community forum. This one is only for Small Business routers where your inquiry is about enterprise ones. I suggest you to move over this post to the LAN, Switching and Routing group from the "Actions" panel on the top right corner of this window or just open up a new one there;
https://supportforums.cisco.com/community/netpro/network-infrastructure/switching
I apologize for the inconvenience and please do not hesitate to reach me back if there is any further assistance we may help you with.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Similar Messages

Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series routers

Dear all,
Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series router?.It is not a leased line.
Which Router model is best for 40 Mbps DSL Broad band termination ?
Thanks&Regards
Ajay Jose K

Hi ,
Below link provides you all model in 800 series .
http://www.cisco.com/c/en/us/support/routers/800-series-routers/tsd-products-support-series-home.html
For your requirement below model should suffice .
Complete throughput from the router is 51 Mbps .
Cisco C891FW Integrated Services Router
HTH
Sandy

Snmp v3 configuration on 1800 series for Nagios v 3.2.2

Hi,
Anybody have idea how to configure snmp v3 in 1800 series routers with Nagios configured for monitoring? Can we keep the community name if keep v3 running? I have configured snmp v3 as per the manual. But if I remove the v2 community name it stop responding? Please can I get the complete example configuration of SNMP v3 on cisco routers or switches with encription enabled?
Thanks,
Baby

Hi,
Usefull Commands:
show snmp                    Displays the SNMP status.
show snmp community   Displays the SNMP community strings.
show snmp engineID      Displays the SNMP engineID.
show snmp group           Displays SNMP roles.
show snmp sessions      Displays SNMP sessions.
show snmp trap             Displays the SNMP notifications enabled or disabled.
show snmp user            Displays SNMPv3 users.
SNMPv3 Hidden Show commands:
show snmp community
show snmp view
show snmp chassis
show snmp location
show snmp contact
Configuration Tasks: configure engineID, views, groups, users, hosts, proxies
Note: Configuring engineID, views, hosts, and proxies is optional
snmp-server engineID local engineID-string
snmp-server group    groupname v3 {auth | noauth | priv}
            [read readview]
            [write writeview]
            [notify notifyview]
            [access access-list]
Ex : snmp-server group henrygroup v3 noauth
snmp-server user username v3 groupname
                [ auth {md5 | sha} key ]
                [priv des56 passwd ]
                [access access-list]
Ex : snmp-server evan evangroup v3 auth md5 evenkey
Note: User with authentication does not appear in the running config (use ‘show user’)‏
snmp-server host    host [ traps | informs ] version 3
            [auth | noauth | priv]
            [udp-port port]
            [notification-type]
Ex : snmp-server host 172.16.20.20 version 3 auth evan
SNMPv3 Configuration example:
snmp-server engineID local 123456789012345678901234
snmp-server evan evangroup v3 auth md5 evankey
snmp-server user henry henrygroup v3
snmp-server group evangroup v3 auth
snmp-server group henrygroup v3 noauth read henryview
snmp-server view henryview mib-2 included
snmp-server view henryview cisco excluded
snmp-server community public RO

Cisco 7600 Series Ethernet Services cards types & queue values

Hello,
There is different types for the Cisco 7600 Series Ethernet Services cards.
( More expensive cards with high queue values and less expensive cards with
low queue values.)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-549419.html
Hardware queues
ES Plus XT 40G line cards
• 128,000 ingress queues
• 256,000 egress queues
ES Plus XT 20G line cards
*• 64,000 ingress queues*
• 128,000 egress queues
Hierarchical QoS (H-QoS)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-570730.html
Hardware queues
Cisco 7600 Series ES Plus Transport 40G and 20G Line Cards
*Supporting up to 16 level 4 queues per physical port*
Hierarchical QoS (H-QoS)
Low queue cards have got only 4 queues per physical port. High queue cards
have got minimum 64.000 queue. This is very huge difference. In what kind
of scenario do we have to use the High queue cards ? Could you give some
examples please ? Kind Regards.
Burak

HI Burak,
Each time you configure a class with bandwidth allocation or shaping,.. a queue will be used so if you use such card to provide QoS for a lot of subscribers sharing the same interface, you will need a lot of them !!
HTH
Laurent.

1800 series router - MPLS - VoIP

I have a customer who wants to implement a VoIP solution on an MPLS network. Will the 1800 series router work in this environment or would they need a different router? If not what would be the minimum router they would need?
Thanks for the help.

Cisco 2800 is the minimum. Check this out
http://www.cisco.com/en/US/products/ps5854/index.html (click on voice for more information)
The model will depend on how my IP phones who are looking at and SRST support and things like that. If the number of users is more than 250+ you will have to go with 3845 considering growth.
HTH

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

DHCP Option 60: Go HERE.

How to bridge a linksys cisco E1200 series router?

I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

purchase 881w, get rid of linksys. That should do it.
Sent from Cisco Technical Support iPad App

Need a tool for flash backup on Cisco 2821 series routers

Hello Folks,
We have around 1200-1500 cisco 2821 series routers on those we are performing the hardware upgrade so we are taking the backup of all the files available in the flash of all the routers, we just want to know is there any trusted tool available to make this task easy to schedule and take the backups.
Please let me know if you know any tool name.
Thanks,
Raja.

Sorry, I don't know any tool that makes a backup of the whole flash...
You could fo it with from ios cli maybe execute it automatically...
To flash:
archive tar /create flash:/backup.tar flash:/
copying directly to ftp should also work:
archive tar /create ftp://test:[email protected]/backup.tar flash:/

Bandwidth throughput

I have question about bandwidth throughput. Here's what I have:
Private link between Las Vegas, NV and Waterloo Canada
100Mb
69ms latency
Max. Theoretical throughput would be 7Mbps
If I copy a file on windows 7 computers to/from, should it be achieving the 7Mbps over the link; in perfect conditions? If it is less than that, and no other network problems are present, should I be contacting the provider to have them look at the link?
For Ex.
254MB file took 9m45s to copy
254MB/9.75 = MB per minute
26 MB per minute
*8 (to change to bits)
208000000 Mbpm
/60 (60s in a minute)
3.47Mps (about half of the theoretical max)
If I am the only one using that link, should I be getting 7Mbps every single time?
I also did some iperf tests with a 64K window. It almost matches the theoretical limit.
iperf results:
[156] 0.0-600.1 sec 591 MBytes 8.26 Mbits/sec

Hi,
What's bad in contacting the provider to have them look at the link?
Regards
Thanveer
"Everybody is genius. But if you judge a fish by its ability to climb a tree, it will live its whole life believing that it is a stupid."

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?

Folks,
Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?
Thanks

If you have enabled mbssid, "guest-mode" would be replaced by "mbssid guest-mode" this would also allow multiple ssid's to be broadcast
-Tim
Sent from Cisco Technical Support iPad App

Error in Cisco 2500 series Wireless Controller

I have this error in Cisco 2500 series Wireless Controller
The AP type Cisco AIR-CAP35021-A-K9
I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series Wireless Controller But the AP get ip .
Please can any on help me .
Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode:

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller

Oracle RAC and Cisco 7000 Series

Has anyone been successful with database 11.1.0.6 or 11.1.0.7 using a Cisco 7000 series router for the cache fusion interconnect.
A simple yes, if you have done so, will be very much appreciated.
We have a cluster that works with 5000 series switches and hangs with 7000 series ... trying multiple physical switches for the test.
Thank you.

It should work properly. One correction it should be switch not router. We have used the same.

Cisco MDS series switch details

Hello I 'm new to CISCO Switch world.
I 'm working as Clariion Admin and have have taken up the responsibilty to manage switches.Since,i am a novice i need little guidance on how work on cisco switches.I know the Zoning (how zoning done on MDS 9000 series switches) part ,but would like to venture deep into the details on CISCO MDS series switches.
Like, the use of Port channels etc.
Will really appreciate if some one can help me with a link or place ( not the configuration guide) where in i can find details on concentrated more on the theory part .
Thanks in advance!

Actually the best info is in the configuration guides. There are some external companies that run training sessions on the MDS to provide in depth training. There is the MDS cookbook available on CCO that is also a good point of information. If you search on 'MDS white papers' after you login into Cisco.com, there are several good documents that might meet your needs.
Hope this hels,
Mike

Bandwidth throughput Cisco 1800 Series

Similar Messages

Maybe you are looking for