Barcode truncated.

I have:
1. Make new system barcode with SE73
2. use code 128 or interleaved 2 of 5
3. for code 128 set width 12, height 150, mode A
4. make new style and assign new barcode to format in there
5. make new smartform and assign newly made style to it
6. make text box fill with random text and assign barcode format to it
7. execute to print preview or print directly, it will produced truncated barcode no matter the text is long(over 16 character) or short(less then 8) or anything in between
Applied notes:
Note 1557244 - Barcode & Barcode Text truncated in certain situations - applied but no effects.
Additional notes:
preview directly within se73 produced correct results.

Similar Messages

Truncated and Shrunk Barcodes in Crystal 8.5?

Post Author: Reinhard Maass
CA Forum: General
I am still working with Crystal 8.5, but lately I have run into a series of weird incidents that made me wonder whether this version has a principal problem when it comes to printing barcodes. Maybe someone of you can confirm my suspicion... or knows about a remedy without having to upgrade.We are printing interleaved 2/5 barcodes on labels with a Zebra XiIII Plus thermotransfer printer.On average, 9,999 of 10,000 labels come out fine. But, on one label the barcode is both truncated and shrunk. What do I mean by this? Say the barcode consists of 25 individual bars. Then, for example only the 13 leftmost bars are printed (truncation), and they are also printed at half height (shrinking). Worst, the printer stops after such a 'bad' label and sometimes even needs to be reset hardware-wise!The problem happens very rarely, but still on a quite regular base. VERY annoying since the complete printout of approx. 1,000 labels stops.
I have tried almost everything, including the famous Seagull printer driver for our Zebra printer, but nothing worked. The only suspicion I have is that it might be related to using the 8.5 runtime for printing those labels:Whenever I call up the one 'bad' label from the stand-alone version of the report the label will come out all right (which does not prove too much, though, since this is one label only and it seems to be a rather random problem).However, when I repeat printing all the labels from the report called up by the runtime this time, it gets stuck at the same label again. So it's not fully random. Still, there is not any 'pattern' to all this.
Does this sound familiar to anyone? Is this a known problem in 8.5? Is there a known fix?Any help would be greatly appreciated - thanks a million!

Hi
It may be possible that the report has got some issues within itself. Try checking as below:
1. The section on which you have the OLE object, insert a subsection below and insert the OLE there.
2. See if that too shrinks.
If that too shrinks, you can also check the size of the image, page set up of crystal, try a landscape.
Regards
Sourashree

Spaces getting truncated in 2D barcode

HI,
I am facing an issue with 2D bar code output where variables with fixed legth are concatenated assigning offset without concatenation statement,
the issues is
if the length of variable is 24 , value is of 18 characters then the remaining 6 spaces are seen in debugg mode but not in output i,e in bar code scanned output.
In such a way it is truncating all the spaces in between.
please help in the above issue .
Thanks In advance
Sowjanya

and if I repalce it with hyphens, data after it gets exported into excel gets corrupted...
forexample : item -987-PD-87 comes out as 0 or ## at some places , it thinks as if there is some mathematical operation and acts weird.
If you have seen the configurator summary page, then it represents an indented bill of material as an expanded tree, with hide/show region appropriately placed at correct sublevel. How can I do that to avoid whitespaces or some other characters ?
thnx

Adobe form barcode scanner input

I made an Adobe form with X Pro. The purpose of the form is to inventory equipment. I use a barcode scanner to enter serial numbers into the form. When I scan the barcode (Code 39) of an item the serial number entered into the form is truncated. To ensure that the scanner was reading the barcode correctly I scanned a code while having notepad open, it input the entire serial number correctly. I did the same thing with Word and the serial was also input correctly. Why is the form truncating my serial number? I can type more in the field if I so wish so I know that a character limit is not the issue. I checked all of the text box's properties but see nothing incorrect or limiting.
Thanks for the help,
Goob

Sorry for never replying to your post. The problem is: I do not know why this is happening.
Your last sentence "on the Text Area the scan seems to stop before entering all digits but when I scroll back through, they are accurate" makes me think. As I wrote earlier, "A barcode scanner is basically just an input device like a keyboard", but very much faster. Somehow it seems that the software acts like it is encountering the carriage return before all the data digits have been processed.
But somehow it also seems to correct itself in a text area that allows multiple lines, but not in a single-line text field.
Yet that does not happen with my barcode scanner, but with yours and the o/p's.
Very confusing! Does anybody else have some thoughts on this?

Barcode alignment / horizontal / vertical w/ sapscript

Hello everyone!
I am developing a sheet of labels wearing a EAN13 Barcode. It has 56 labels (german brand, no 3668) on a sheet. one label is presented by one instance of the main window, the "First" Page consists of 56 page windows.
i put the structure into a form in sapscript and for any label on its position i do call a new window and write its contents into it. ( A Barcode of EAN and under or above the barcode i would like to see one line of text).
What happened till now?
I have copied BC_EAN13 to a ZBarcode in both a system and a printer barcode.
The barcode is printed via DIMM Module and it works. It is now 5 mm high and 35 mm wide, what should easily fit into a 52,5 * 21,2 mm label.
Problem: 1st line - barcode is truncated. if i add lines in the form as spacers, it does not move below so that i can ensure ideal positioning on the sheet.
on the label sheet there´s no border, i even tried the option baseline alignment, but it made it even worse.
So: problem is how to find exact position of the barcode on a label sheet. how to move it a little bit below, find space for one line of text and print all 56 labels on a sheet without the first line being truncated.
please also advice if the printer can not print sheets borderless (HP4350 cyrillic ´version).
thx,
br
stefan

Thanks Andrew!
Since not everyone posts solution if it is solved by the people themselves, here´s my solution in case anyone is interested:
The hint was what i basically did before, lots of page windows representing one label on the sheet.
It seems that printing on the very top of the page (upper space 0 mm) and printing a barcode there could not be done by the printer,
so after i skipped the first line of labels (deleted first row of page windows) i got a much better result. i can´t use all the labels now, but it hit and therefore it works now - no more unstable positioning,
double print of same barcode in same window etc.
I hope everyone understood this rough explanation.

Barcode/sapscript alignment horizontal / vertical on hp4350 cyrillic

Hello everyone!
I am developing a sheet of labels wearing a EAN13 Barcode. It has 56 labels (german brand, no 3668) on a sheet. one label is presented by one instance of the main window, the "First" Page consists of 56 page windows.
i put the structure into a form in sapscript and for any label on its position i do call a new window and write its contents into it. ( A Barcode of EAN and under or above the barcode i would like to see one line of text).
What happened till now?
I have copied BC_EAN13 to a ZBarcode in both a system and a printer barcode.
The barcode is printed via DIMM Module and it works. It is now 5 mm high and 35 mm wide, what should easily fit into a 52,5 * 21,2 mm label.
Problem: 1st line - barcode is truncated. if i add lines in the form as spacers, it does not move below so that i can ensure ideal positioning on the sheet.
on the label sheet there´s no border, i even tried the option baseline alignment, but it made it even worse.
So: problem is how to find exact position of the barcode on a label sheet. how to move it a little bit below, find space for one line of text and print all 56 labels on a sheet without the first line being truncated.
please also advice if the printer can not print sheets borderless (HP4350 cyrillic ´version).
thx,
br
stefan
Message was edited by:
Stefan Loibner
Message was edited by:
Alvaro Tejada Galindo

Thanks Andrew!
Since not everyone posts solution if it is solved by the people themselves, here´s my solution in case anyone is interested:
The hint was what i basically did before, lots of page windows representing one label on the sheet.
It seems that printing on the very top of the page (upper space 0 mm) and printing a barcode there could not be done by the printer,
so after i skipped the first line of labels (deleted first row of page windows) i got a much better result. i can´t use all the labels now, but it hit and therefore it works now - no more unstable positioning,
double print of same barcode in same window etc.
I hope everyone understood this rough explanation.

Regarding Barcode Type....

Hi friends...
     How can I get the information about the attributes of different barcode types   used in Smartforms?
Kindly Suggest me the solution for this query???
Points will be rewarded to the useful answer...
Thanx,
Rahul.

Hi Rahul,
You can use barcodes types already created or you can create new one if
these types does not satisfy you requirement.
If you create a new system bar code for the "new bar code technology" in transaction SE73, you must specify the following parameters:
Bar code name (used in Smart Styles)
Short text for system bar code (documentation)
Bar code symbology:
    Code39
    Code128
    Interleaved 2of5
    PDF417
    Code93
This selection determines the technical bar code type that is used to format the bar code data (also called bar code symbology). The symbology also determines which characters are allowed in the bar code data.
Bar code alignment:
Normal (that is, the scan direction is "from left to right")
Rotated (the scan direction is rotated by 90 degrees "from top to bottom")
Inverted (the scan direction is rotated by 180 degrees "from right to left")
Bottom-up (the scan direction is rotated by 270 degrees "from bottom to top")
Code39 ******************
Code39 is an alphanumeric code that can represent the following characters in the bar code data:
Numbers:        1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
The start and stop character for the Code39 bar code is usually represented by an asterix (*) in the text view of the bar code data (also called "human-readable text" or "interpretation line").
Parameters for Code39:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Mod-43 check digit
Value range: X equals YES, blank character equals No
With this indicator, you can determine whether a Modulo-43 check digit is to be generated.
Bar ratio
Value range: 20 to 30
This value controls the ratio between wide and narrow bars. This value controls the ratio between wide and narrow bars.Value 20 means a ratio of 2.0:1, value 30 means a ratio of 3.0 to 1 (that is, 3:1).
Parameters for Interleaved 2of5:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Mod-10 check digit
Value range: X equals YES, blank character equals No
With this indicator, you can determine whether a Modulo-10 check digit is to be generated.
Bar ratio
Value range: 20 to 30
This value controls the ratio between wide and narrow bars. This value controls the ratio between wide and narrow bars.Value 20 means a ratio of 2.0:1, value 30 means a ratio of 3.0 to 1 (that is, 3:1).
Code 128 *****************
Code128 is an alphanumeric code that can encode three different character sets. Each of the three character sets can represent 106 different characters. Within a bar code, you can alternate between the character sets.
The three Code128 character sets are named as follows:
Subset A) (contains, for example, digits, capital letters and control characters)
Subset B) (contains, for example, digits, uppercase and lowercase letters)
Subset C) (digit pairs from 00 to 99)
Parameters for Code128:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Code128 mode
Value range: N (default value), A, U
In default mode N (None), the Code128 bar code works in subset B. If you want to switch to another subset, you must trigger the change explicitly with a control command ("invocation code") in the bar code data.
In mode A (automatic), the software analyzes the transferred bar code data and recognizes automatically which subset is the most adequate for the bar code data. Subsets are swapped automatically in the bar code data. A sequence of four or more digits initiates an automatic change in subset C.
In mode U (UCC case mode), you must transfer 19 digits in the bar code data. Subset C is set automatically and an FNC1 character is added as prefix.
Note: If fewer than 19 digits are transferred, the bar code is filled with zeros to the left until it contains 19 digits.
UCC check digit
Value range: X equals YES, blank character equals No
Note: This parameter has no effect becaues Code128 always generates a check digit, even in UCC mode. The parameter will be removed in the future.
Code93 is an alphanumeric code that can represent the following characters directly in the bar code data:
Numbers:        1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
The start and stop characters in the Code93 bar code are represented as # sign in the text view of the bar code data (also called "human-readable text" or "interpretation line").
Parameters for Code93:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Check digit
Value range: X equals YES, blank character equals No
With Code93 bar codes, a pair of check digits is always used and is always generated in the bar code. This parameter has no effect.
PDF417 is a two-dimensional bar code to represent datasets that are larger as the usual datasets in one-dimensional bar codes (for example, more than 1,000 characters). The entire 7-Bit ASCII character set is generally processed (binary values 1 - 127, the value 0 is not permitted).
A PDF417 bar code consists of 3 to 90 consecutive rows. Every row consists of a start/stop indicator and "code words". A code word consists of 4 bars and 4 spaces. The minimum number of code words per row is three.
Parameters for PDF417:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
This parameter currently has no effect on PDF417. The height of a PDF417 symbol is controlled by parameter "Single Row Height" and the number of columns and rows, in conjunction with the length of text data to be encoded.
Single row height
Value range: 1 to 32000
This value, multiplied by the narrow module width, returns the height of the individual rows of a PDF417 symbol, measured in pixels. Caution: Do NOT use the value 1 for this parameter
Security level
Value range: 0, 1-8
This parameter controls the number of code words that are generated for error recognition and error correction. The default value 0, however, only permits error recognition but no automatic correction. If you increase the security level, the level of error correction increases with it (this increases the size of the bar code).
Number of columns
Here, you can define the number of the code word columns which you can use to check the width of the bar code.
Value range:
0 (default value) : A row/column ratio of 1:2 is used.
Permitted values: 1 to 30
Number of rows
Here, you can define the number of rows which can be used to check the height of the bar code.
Value range:
0 (default value) : A row/column ratio of 1:2 is used.
Permitted values: 3 to 90
For example: If you leave both parameters set to the default value 0, the system would convert 72 code words in a bar code symbol with 6 columns and 12 rows.
Truncation
Value range: X equals YES, blank character equals No
This indicator determines if the right row indicator and the stop pattern are to be truncated (this saves space).
The following character combinations in the transferred bar code data have the special function:
\&    - This represents the end of a line (Carriage Return + Newline)
    - This represents a backslash (5C hexadecimal)
\0xYY - This represents a single byte with the value YY (hexadecimal)
        For example: \0x1E is output as a single byte with the value 1E (hex)
        or 30 (decimal).
The souce for this information is OSS Note 645128.
Still if u face any problem feel free to ask.
Regards,
Vivek
-Reward if useful

Creating new PDF417 Barcode for SmartForm

Hi Experts,
I want to create a new PDF417 Barcode into SE73 but I don't know how to interpret following instructions:
PDF417 ISO 15434
Xdim = 13mils
Xdim / Ydim = 1 / 3
SAP allow following properties:
Narrow Module With
Linear Height
Single Row Height
of Columns (1-30)*
of Rows (3-90)*
SecurityLevel
Truncation.
Regards,
David

Hi,
nobody ? How can I define the barcode with these X/Y properties ?
Regards,
David

Problem with code39 barcode

Post Author: rlisario
CA Forum: Crystal Reports
In a report I've insert a text object with caption 123 (with asterisk)
Then I've change in a Code39 font and in a project windows seems all ok.
But when I do the preview (or print) the barcode is become truncate and corrispond to 123 (not 123)
Is it possible that in preview (or print) Crystal Report remove the control caracter asterisk ?!?
Can be a license problem to use barcode font in Crystal Report ?
Thanks for help,Rinaldo.

Post Author: rlisario
CA Forum: Crystal Reports
The problem there is with CR XI include with Visual Studio 2005 Professional
I've do test with CR X developer edition and it's all ok
I thinks that it's a limitation of CR XI include with Visual Studio 2005 Professional, really?!?
Thanks for help,Rinaldo.

SSCC 18 barcode.

(Reposted Question)
1. What is Business standard length of barcodes (printed labels) for SSCC 18. Is it 20 character barcodes or 18 character??
2. Can the length of a barcode (read by a device) be modified before it is displayed on the SAP/RF screen.
For Ex: If we scan a barcode of 20 characters can the device truncate the initial 2 characters (which are 0's in SSCC18) and display only last 18 characters on the screen.
(I am aware that we can append zeros to the barcode scan before displaying)

Hi,
>>>1. What is Business standard length of barcodes (printed labels) for SSCC 18. Is it 20 character barcodes or 18 character??
length 18
http://www.barcodetools.com/barcode-types/linear-barcodes/linear-barcodes.html
Regards,
michal

SSCC 18 Barcode in RF.

1. What is universal standard length of barcodes for SSCC 18. Is it 20 character barcodes or 18 character??
2. Can the length of a barcode (read by a device) be modified before it is displayed on the SAP/RF screen.
For Ex: If we scan a barcode of 20 characters can the device truncate the initial 2 characters (which are 0's in SSCC18) and display only last 18 characters on the screen.
(I am aware that we can append zeros to the barcode scan before displaying)

Hi Rohit!
Answer to Q1:
The SSCC18 has 20 digits. The first two digits in this case are the application identifier. It tells the application that the 18 digits following the application identifier have this structure (if one is
specified) and this meaning. UCC/EAN 128 is the bar code symbology.The SSCC18 is an implantation of that symbology with very specific rules set by the
Uniform Code Council (see www.uc-council.org).
Answer to Q2:
You define the Input Field with Length 20 in you SAP/RF Screen.
Set your RF Device for <AUTOENTER>,meaning as soon as you scan <ENTER> is pressed automatically.When you do it in the SAPGUI you handkey the 20 digit value and press enter manually.
In your PAI write ABAP Code to trim the 20 digit barcode value to 18.Basically remove the application identifier 00.
With this the moment you scan your PAI is triggerred and you will see only the 18 digits during the next Screen Display.
This will definitely work.Hope this answers your question.Let me know.
Thank You
Gisk

Barcode C128 is not getting displayed in Sapscript

HI,
I need to print the barcode in the Sapscript.
The barcode is not getting displayed even in the preview also, when I give the Barcode C128.
But when I give other Barcodes, it is getting displayed in the preview.
Can anyone let me know the solution to print the barcode for C128, as others are not that much fit to print.
Thanks
Rakesh

Hi Dieter,
No. I haven't.
Is this the reason for that?
let me know the procedure.
thanks
Rakesh

Barcode report is not working in linux

hi,
i am running the report using the barcode, which is running perfectly in the windows server - i meant in the report builder.
but when i try run the same report in linux server through application, i am getting the below mentioned error:
Terminated with error:
REP-1401: 'beforereport': Fatal PL/SQL error occurred. ORA-39565: Message 39565 not found; product=RDBMS; facility=ORA
below mentioned is the code written in beforereport trigger:
globals.barcode_to_use := BarCodeConstants.BAR_CODE_128;
globals.bcobj := barcodemaker.new();
i have include the jar file path /ora/u01/oracle/v101/ds1/reports/jlib/oraclebarcode.jar both in class path and report_path, but still its not working.
any one had solve this issue?...pls help me out
for you info:
CLASSPATH=/ora/u01/oracle/v101/ds1/j2ee/OC4J_BI_Forms/applications/formsapp/formsweb/WEB-INF/lib/frmsrv.jar:/ora/u01/oracle/v101/ds1/jlib/repository.jar:/ora/u01/oracle/v101/ds1/jlib/ldapjclnt10.jar:/ora/u01/oracle/v101/ds1/jlib/debugger.jar:/ora/u01/oracle/v101/ds1/jlib/ewt3.jar:/ora/u01/oracle/v101/ds1/jlib/share.jar:/ora/u01/oracle/v101/ds1/jlib/utj.jar:/ora/u01/oracle/v101/ds1/jlib/zrclient.jar:/ora/u01/oracle/v101/ds1/reports/jlib/rwrun.jar:/ora/u01/oracle/v101/ds1/forms/java/frmwebutil.jar:/ora/u01/oracle/v101/ds1/reports/jlib/oraclebarcode.jar
RW=$ORACLE_HOME/reports; export RW
REPORTS_PATH=$ORACLE_HOME/reports/templates:$ORACLE_HOME/reports/samples/demo:$ORACLE_HOME/reports/integ:$ORACLE_HOME/reports/printers:${REPORTS_PATH}; export REPORTS_PATH
REPORTS_TMP=/tmp; export REPORTS_TMP
REPORTS_NO_DUMMY_PRINTER=TRUE; export REPORTS_NO_DUMMY_PRINTER
REPORTS_TAGLIB_URI=/WEB-INF/lib/reports_tld.jar; export REPORTS_TAGLIB_URI
REPORTS_CLASSPATH=$ORACLE_HOME/reports/jlib/rwbuilder.jar:$ORACLE_HOME/reports/jlib/rwrun.jar:$ORACLE_HOME/jlib/zrclient.jar:$ORACLE_HOME/j2ee/home/oc4j.jar:$ORACLE_HOME/j2ee/home/lib/ojsp.jar:$ORACLE_HOME/reports/jlib/oraclebarcode.jar; export REPORTS_CLASSPATH
repserver.conf file setting:
<engine id="rwEng" class="oracle.reports.engine.EngineImpl" initEngine="1" maxEngine="1" minEngine="0" engLife="50" maxIdle="30" callbackTimeOut="90000" jvmOptions="-Xms512m -Xmx512m" classPath="/ora/u01/oracle/v101/ds1/reports/jlib/oraclebarcode.jar">
<property name="sourceDir" value="/ora/u02/oraadmin/config/as2/app_qits_run"/>
<property name="tempDir" value="/ora/u02/oraadmin/config/as2/app_qits_tmp"/>
</engine>
<engine id="rwURLEng" class="oracle.reports.urlengine.URLEngineImpl" initEngine="1" maxEngine="1" minEngine="0" engLife="50" maxIdle="30" callbackTimeOut="60000" classPath="/ora/u01/oracle/v101/ds1/reports/jlib/oraclebarcode.jar"/>
thanks
renjish

Hello,
The first step if to find the PL/SQL line causing the error in 'cf_1formula':
create a procedure Trace in your Reports : (modify the line trace_file := Text_IO.Fopen('d:\temp\rep_trace.txt', 'A'); to adapt the filename to your system)
PROCEDURE Trace (trace_string in varchar2) IS
trace_file Text_IO.File_Type;
BEGIN
trace_file := Text_IO.Fopen('d:\temp\rep_trace.txt', 'A');
Text_IO.Put_Line(trace_file, trace_string);
Text_IO.Fclose (trace_file);
END;
Then, add some calls to this procedure in the program unit 'cf_1formula'
trace('Before line 1';
<PL/SQL code of line 1>
trace('Before line 2';
<PL/SQL code of line 2>
trace('Before line 3';
<PL/SQL code of line 3>
Excecute the Reports and find in the file 'd:\temp\rep_trace.txt' the last line executed.
Regards

Print a report on doc format truncate data

hi
I have a report launching with a form in an oracle applications, when I print a report on pdf format looks ok
but when I print the same report on doc format truncate data on left and right side.
Can you help me
thanks

Hi Herbe
Reports does not support .doc format. Are you referring .rtf format?
In any case, you must contact Oracle Support to get the issue resolved.
Regards
Sripathy

Why does FireFox truncate part of an E-mail of more than one page when I try to print it out? How can I sent an E-mail blaet to several but only show one name o

When I try to print out an E-mail that is longer than one page, part of the 2nd page is truncated. I then have to go to Safari to print out the entire E-mail without part of it being truncated.
When I have multiple E-mail addresses on a single E-mail, how can I send the E-mail so that each recipient only sees his/her name and E-mail address rather than everyone else that the E-mail is addressed to?
Please advise.
Thank you.
Bill Leete

Some style rules that Firefox handles well on the screen can cause this problem. Many email sites have a print button which simplifies the message format and removes navigation elements, etc., and Firefox generally handles print-formatted pages better. If your email site doesn't have print-formatted pages or those do not print, a "hack" is to select the text you want to print and then choose the Selection option in the print dialog.
To hide email addresses from recipients, you need to place them in the BCC field. What do you put in the TO field in that case? You can use your own address.

Barcode truncated.

Similar Messages

Maybe you are looking for