Bare metal restore of full server backup fails with RPC error 0x800706BA (server 2012)

With Windows Server 2012, after creating a successful windows server backup (full server), I am unable to do a bare metal restore of the system.
EFI System Partition, C:, D: are the volumes on a single array (Raid 5).
Loading WinRE and launching re-image, the full server restore stops after completing the C: restore just after beginning the D: drive restore (data volume) with the error with the message about RPC error 0x800706BA, unavailable.
The system will not boot as a result of the failure. 
What may be causing this?
[edit]
I think I have two things working against me here... one, Volume Shadow Copy service wasn't running in WinPE and two.. the D: volume contains data deduplication.
I think this is causing some of my problems.
Is there an additional service that I need to start in WinPE to get a volume that was deduplicated restored perhaps using wbadmin?

Hi,
Thanks for the reply Shaon.
The hardware system is identical; however, I am increasing storage capacity from 12TB to 16TB.  Basically, the system is the same, just new hard drives (4x4TB versus 4x3TB).  Drives are all identical enterprise class drives and I am actually using
the same system (backup, swap drives then restore).
I tried both using the WinRE restore (re-image) with the backup set, and tried using wbadmin.  Both produce same RPC unavailable messages (although using the GUI based tool via WinRE provides the additional error code #).
I do not have any idea what to look at to try to figure this one out.
[edit]
I was just informed of this posting:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/147efccc-e0e9-4458-852e-c3a44ae5cb64/the-system-image-restore-failed-error-details-he-rpc-server-is-unavailable-0x800706ba?forum=windowsbackup
and in my case, this lab server does in fact act also as a DC as well as a file server...  do I need to spin up a secondary controller (perhaps in a VM on another machine) to do this restore?

Similar Messages

  • Windows Server 2012 Windows Backup failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).

    The Volume Shadow Copy service initially was running under the context of System, so we thought that ‘System’ doesn’t have permissions to access network shares. 
    When the Volume Shadow Copy service was running under the context of System, this was the error logged:
    “failed with following error code '0x8078014B' (There was a failure in creating a directory on the backup storage location.).”
    Which is likely due to not having permissions to write to the network location. 
     This is a scheduled backup trying to write to a network location, so we changes the service to run under the context of an account that does have permissions to write to the network share.
      Then the error changed to this:
    “failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).”
    HRESULT 0x8078006b
    DetailedHRESULT 0x8004230f
    ErrorMessage %%2155348075
    BackupState 12
    VolumesInfo <VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0"
    BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0"
    TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228"
    DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0"
    FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0"
    /></VolumeInfo>
    We aren’t really seeing anything that gives any hint on what the issue is. 
    Any ideas?  Thanks in advance!

    We are trying to back up folders/files from 2 local drives (C: & D:), both of which have only 10% space used, and 100 GB free. 
    We are attempting to back the files up to a Remote Shared File (and there is 100+ GB free space out there). 
      If we try another network location, we receive the exact same error. 
     This is Windows Server 2012, not running Hyper-V and is a physical server not a VM.
    Thank you for the link. 
    Looking in: 
    Event Viewer / Application and Service Logs / Microsoft / Windows / Backup / Operational
    But it doesn’t seem to give any more details: 
    Log Name:     
    Microsoft-Windows-Backup
    Source:       
    Microsoft-Windows-Backup
    Date:         
    7/8/2013 8:00:12 PM
    Event ID:     
    5
    Task Category: None
    Level:        
    Error
    Keywords:     
    User:         
    SYSTEM
    Computer:     
    servername.edu
    Description:
    The backup operation that started at '‎2013‎-‎07‎-‎09T02:00:06.273000000Z' has failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).
    Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.
    Event Xml:
    <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
      <System>
    <Provider Name="Microsoft-Windows-Backup" Guid="{1DB28F2E-8F80-4027-8C5A-A11F7F10F62D}" />
    <EventID>5</EventID>
    <Version>3</Version>
    <Level>2</Level>
    <Task>0</Task>
    <Opcode>0</Opcode>
    <Keywords>0x4000000000000000</Keywords>
    <TimeCreated SystemTime="2013-07-09T02:00:12.872602100Z" />
    <EventRecordID>30</EventRecordID>
    <Correlation />
    <Execution ProcessID="3028" ThreadID="3996" />
    <Channel>Microsoft-Windows-Backup</Channel>
    <Computer>servername.edu</Computer>
    <Security UserID="S-1-5-18" />
      </System>
      <EventData>
    <Data Name="BackupTemplateID">{A421E864-A115-4288-8D12-F4878CF8A248}</Data>
    <Data Name="HRESULT">0x8078006b</Data>
    <Data Name="DetailedHRESULT">0x8004230f</Data>
    <Data Name="ErrorMessage">%%2155348075</Data>
    <Data Name="BackupState">12</Data>
    <Data Name="BackupTime">2013-07-09T02:00:06.273000000Z</Data>
    <Data Name="BackupTarget">\\servername\BACKUP</Data>
    <Data Name="NumOfVolumes">2</Data>
    <Data Name="VolumesInfo">&lt;VolumeInfo&gt;&lt;VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0"
    IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /&gt;&lt;VolumeInfoItem
    Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0"
    NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /&gt;&lt;/VolumeInfo&gt;</Data>
    <Data Name="SourceSnapStartTime">2013-07-09T02:00:06.289250300Z</Data>
    <Data Name="SourceSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="PrepareBackupStartTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="PrepareBackupEndTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="BackupWriteStartTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="BackupWriteEndTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="TargetSnapStartTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="TargetSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="DVDFormatStartTime">&lt;TimesList&gt;&lt;/TimesList&gt;</Data>
    <Data Name="DVDFormatEndTime">&lt;TimesList&gt;&lt;/TimesList&gt;</Data>
    <Data Name="MediaVerifyStartTime">&lt;TimesList&gt;&lt;/TimesList&gt;</Data>
    <Data Name="MediaVerifyEndTime">&lt;TimesList&gt;&lt;/TimesList&gt;</Data>
    <Data Name="BackupPreviousState">2</Data>
    <Data Name="ComponentStatus">&lt;ComponentStatus&gt;&lt;/ComponentStatus&gt;</Data>
    <Data Name="ComponentInfo">&lt;ComponentInfo&gt;&lt;/ComponentInfo&gt;</Data>
    <Data Name="SSBEnumerateStartTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="SSBEnumerateEndTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="SSBVhdCreationStartTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="SSBVhdCreationEndTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="SSBBackupStartTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="SSBBackupEndTime">1601-01-01T00:00:00.000000000Z</Data>
    <Data Name="SystemStateBackup">&lt;SystemState IsPresent="0" HResult="0" DetailedHResult="0" /&gt;</Data>
    <Data Name="BMR">&lt;BMR IsPresent="0" HResult="0" DetailedHResult="0" /&gt;</Data>
    <Data Name="VssFullBackup">false</Data>
    <Data Name="UserInputBMR">false</Data>
    <Data Name="UserInputSSB">false</Data>
    <Data Name="BackupSuccessLogPath">
    </Data>
    <Data Name="BackupFailureLogPath">
    </Data>
    <Data Name="EnumerateBackupStartTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="EnumerateBackupEndTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="PruneBackupStartTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="PruneBackupEndTime">&lt;TimesList&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;Time Time="1601-01-01T00:00:00.000Z" /&gt;&lt;/TimesList&gt;</Data>
    <Data Name="BackupFlags">0x9</Data>
    <Data Name="ComponentInfoSummary">&lt;ComponentInfoSummary ComponentInfoArrayPresent="1" TotalComponents="0" SucceededComponents="0" /&gt;</Data>
      </EventData>
    </Event>

  • Backup fail with VSSwriter error

    Hello,
    we currently are using Symantec Backup on tape and Windows Server Backup to make two differents backups on a SBS 2008.
    We are getting failed backup randomly during the week for both. Sometimes one is succeed and not the others.
    We have found several post about the VSS issues and how to fix it but nothing has changed.
    What we have done:
    - check the VSS writer and all is in "no error" state
    - check the settings of the backups
    - restart the VSS services
    - Configure the Shadow Copy on the drives
    - reboot the server
    - Tried several solutions from forums
    What we can see in the event viewer
    ID 12289
    "Volume Shadow Copy Service error: Unexpected error VSS_E_WRITER_STATUS_NOT_AVAILABLE. An older active writer session state is being overwritten by a newer session. The most common cause is that the number of parallel backups has exceeded the maximum
    supported limit.  hr = 0x80042409. 
    Operation:
       Aborting Writer
    ID 7001
    VssAdmin: Unable to create a shadow copy: The shadow copy provider had an error. Please see the system and application event logs for more information. 
    Command-line: 'C:\Windows\system32\vssadmin.exe Create Shadow /AutoRetry=15 /For=C:\'. "
    ID 12341
    Volume Shadow Copy Warning: VSS spent 75 seconds trying to flush and hold the volume \\?\Volume{c22d5d46-0540-11e0-9496-806e6f6e6963}\.  This might cause problems when other volumes in the shadow-copy set timeout waiting for the release-writes phase,
    and it can cause  the shadow-copy creation to fail.  Trying again when disk activity is lower may solve this problem. 
    Operation:
       Executing Asynchronous Operation
    Context:
       Current State: flush-and-hold writes
       Volume Name: \\?\Volume{c22d5d46-0540-11e0-9496-806e6f6e6963}\"
    Some will post the link of "how to troubleshoot VSSwriter issue": we have already used it.
    Does someone have a fresh idea about this issue ?
    Thanks in advance

    Hi Nerea,
    Before going further, would you please let me confirm if temporarily disable either of the two backup, will
    another backup operation run smoothly? In other words, if temporarily disable Symantec Backup, will Windows Server Backup always run successfully? Or if disable Windows Server Backup, will Symantec Backup always run successfully? Please check if Windows Server
    Backup conflicts with Symantec Backup.
    Based on the error message, please run
    chkdsk command and check if there is any issue in the disk. Then use
    Vssadmin resize shadowstorage to resizes the maximum amount of storage space that can be used for shadow copy storage. And check if this issue still persists.
    In addition, would you please let me know whether re-register Volume VSS components? If this issue still persists,
    please re-register and monitor the result.
    From command prompt:
    cd windows\system32
    Net stop vss
    Net stop swprv
    regsvr32 ole32.dll
    regsvr32 vss_ps.dll
    Vssvc /Register
    regsvr32 /i swprv.dll
    regsvr32 /i eventcls.dll
    regsvr32 es.dll
    regsvr32 stdprov.dll
    regsvr32 vssui.dll
    regsvr32 msxml.dll
    regsvr32 msxml3.dll
    regsvr32 msxml4.dll
    net start swprv
    net start vss
    By the way, did the Symantec Backup and Windows Server Backup run at the same time? Or before one backup finished,
    had another backup started?
    Hope this helps.
    Best regards,
    Justin Gu

  • FULL HOT Backup failing with a 6 on media management layer....

    Hi all,
    My thanks in advance for reading and any posts. Appologies for the long post, but wanted to make sure I got all information required into the post
    *******************The background*************************
    We are currently doing full hot backups of all production databases to tape. The database we use is RAC install (9.2.0.6.0) on Linux Redhat Enterprise 4 (database on OCFS). We use a seperate Solaris 8 box with 2 HP Ultium tape drives over a standard Cat5 line (100mb), we use Veritas Netbackup 5.1 as our media manager and we use an RMAN repositry on another box. Currently the backup is taking on average 17 hours to complete (something that I have been through with Oracle).
    We use the below rman script to do the full database backup.
    DATE=`date +%m%d%Y-%H%M%S`; export DATE
    USER=`id | cut -f2 -d"(" | cut -f1 -d")"`
    ORACLE_SID=ausl5; export ORACLE_SID
    ORACLE_USER=oracle; export ORACLE_USER
    ORACLE_HOME=/u01/oracle/product/9.2.0 export ORACLE_HOME
    #delete log files older than 35 days
    find /var/adm/netbackup -name "auslive*" -mtime +35 -type f -exec rm {} \;
    #if [ "${USER}" = "root" ]
    #then
    # su - ${ORACLE_USER} "cd /rac/DBA/scripts/BACKUP/" #-c "${CMD_STRING}"
    # SUCCESS=$?
    #else
    # eval "/rac/DBA/scripts/BACKUP"
    # SUCCESS=$?
    #fi
    <<EOF su - oracle
    <<EOF1 /u01/oracle/product/9.2.0/bin/rman msglog /var/adm/netbackup/AUSLIVE_b
    ackup.${DATE} append
    connect target sys/fowler@rman_ausl5
    connect catalog rman/rman@rman
    #change archivelog all validate;
    run {
    allocate channel ch1 type sbt_tape PARMS="BLKSIZE=1048576";
    #allocate channel ch2 type sbt_tape PARMS="BLKSIZE=1048576";
    #allocate channel ch3 type sbt_tape;
    CONFIGURE DEFAULT DEVICE TYPE TO 'SBT_TAPE';
    CONFIGURE CHANNEL 1 DEVICE TYPE 'SBT_TAPE' MAXPIECESIZE 100000m
    CONNECT = 'SYS/fowler@rman_ausl5';
    #CONFIGURE CHANNEL 2 DEVICE TYPE 'SBT_TAPE' MAXPIECESIZE 100000m
    CONNECT = 'SYS/fowler@rman_ausl3';
    #CONFIGURE CHANNEL 3 DEVICE TYPE 'SBT_TAPE' CONNECT = 'SYS/fowle
    r@rman_ausl4';
    change archivelog all validate;
    ###=============== Veritas Calls =========================
    send "NB_ORA_CLASS=ORAhot_AUSLIVE";
    #send "NB_ORA_CLIENT=sunatlsunx008";
    send "NB_ORA_CLIENT=sunatlsunx008";
    send "NB_ORA_SCHED=full";
    ###=====================main backup sections =============
    backup
    incremental level=0
    filesperset 15
    format "bk_%s_%p_%t"
    tag "hot_${ORACLE_SID}_${DATE}"
    database;
    sql "alter system archive log current";
    change archivelog all validate;
    backup
    filesperset 10
    format "ct_%s_%p_%t"
    current controlfile;
    sql "alter system archive log current";
    backup
    filesperset 150
    format "al_%s_%p_%t"
    archivelog all not backed up 2 times;
    change archivelog all validate;
    backup
    filesperset 50
    format "al_%s_%p_%t"
    archivelog until time 'SYSDATE-4' delete input;
    change archivelog all validate;
    release channel ch1;
    #release channel ch2;
    #release channel ch3;
    exit
    EOF1
    EOF
    Now due to the backup taking so long, we often have archive log backups that kick off. We generally get Restore Validates of this backup once a week.
    *********************************Problem*******************************
    Getting to the problem, the media manager generally completes the job with a 6, which in Veritas means that the backup failed to back up the requested files. I guess that this could be something to do with the media manager layer. But myself and my colleagues are of the opinion that this is something to do with the archive log backups running inbetween (hence the change archivelog all validate; appearing so many times in the script).
    Has anyone got any ideas?
    Thanks again for any posts / ideas,
    Mark.

    No I mean, it really tries to backup everything; control file, archive logs etc...
    Yeah I will admit its a bit strange, didn't code it myself. The idea was to do a bit a of house keeping at the same time with the archived redo logs (hence the file system stuff with the archived redo logs).
    You see we thought that this might be causing the issue.
    any ideas are welcomed,
    thanks again,
    Mark.

  • CRS 5 Backups fail with this error: Unknown error occured while connecting to the host

    Dear All,
    We have backup issue with  UCCX 5.0(2)SR03_Build317, while trying to take  backup giving following error "Unknown error occurred while connecting to the host".
    I have found the solution in the Cisco and tried all the suggestion, still not working and same error observed. Due to backup issue we unable to do any changes on the CRS, when we try to create new agents, those agents are not reflecting in the CRS.
    Also I have observed bellow error , when try to re-sync the JTAPI,
    Error while handling the input   request.
    Top of Form
    Config Changes are not allowed during 'Backup' operation, which   was started by 'Scheduler' at 'Fri Jun 08 18:00:03 GMT+08:00 2012 '. Please   try again after 'Backup' is complete.
    Bottom of Form
    http://www.cisco.com/en/US/products/sw/custcosw/ps1846/products_tech_note09186a00809a752c.shtml
    Solution
    Complete these steps in order to resolve this issue:
    •1.      Access the UCCX server and navigate to Start > Run, and type CET.
    •2.      When the warning message appears, click NO.
    •3.      Choose com.cisco.crs.cluster.config.ArchiveAdminConfig.
    •4.      On the right side, double-click the record ID.
    •5.      Click the com.cisco.crs.cluster.config.ArchiveAdminConfig tab, and clear the password under Backup Storage.
    •6.      Click Apply.
    •7.      Navigate to Appadmin > Tools > Backup and Restore.
    •8.      Under Backup Storage Location, type the new password, and click Update.
    After you complete these steps, you can run the backup. If the backup fails, restart the server, and try the backup again. If the backup still fails, you can navigate to CET, clear all the fields, and then type the new information for the storage location.
    Please help me with your suggestions.
    Thanks & Regards,
    Naveen .S

    Please any one help me on this issue..

  • Windows 2008 R2 state backup fails with various errors

    Since a few years we are using DPM to backup our servers but since some time the system state of the server where DPM is installed started to fail.
    I was trying to do system state backup using command line windows backup:
    wbadmin start systemstatebackup -backupTarget:C:
    and it fails every time with different error (last 5 tries):
    1. Error in backup of C:\Windows\winsxs\Manifests\x86_microsoft-windows-w..pdateclient-activex_31bf3856ad364e35_7.6.7600.256_none_09f272fb52ab0c3f.manifest during read: Error [0x80070002] The system cannot find the file specified.
    2. Error in backup of C:\Windows\System32\msmpeg2vdec.dll during write: Error [0x80070002] The system cannot find the file specified.
    3. Error in backup of C:\Windows\System32\catroot\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\Microsoft-Windows-WinMan-WinIP-Package-TopLevel~31bf3856ad364e35~amd64~~7.1.7601.16398.cat during read: Error [0x80070015] The device is not ready.
    4. Error in backup of C:\ during read: Error [0x80070005] Access is denied.
    5. Error in backup of C:\Windows\System32\ActionCenter.dll during write: Error [0x80070002] The system cannot find the file specified.
    That's a Windows 2008 R2 server with DPM and OM servers installed.
    The system state backup was doing fine for 2 or 3 years and suddenly it just stopped.:/

    Hi,
    It seems that we cannot use a volume that is included in the backup as a storage location, please backup to another volume to see the result. 
    You could refer to the article below to troubleshoot the issue:
    Reasons why the error Enumeration of the files failed may occur during System State backup
    http://blogs.technet.com/b/askcore/archive/2010/06/18/reasons-why-the-error-enumeration-of-the-files-failed-may-occur-during-system-state-backup.aspx
    In additional, as the server with DPM installed, I suggest you also ask for help from DPM forums:
    http://social.technet.microsoft.com/Forums/en-US/home?forum=dataprotectionmanager&filter=alltypes&sort=lastpostdesc
    Regards,
    Mandy
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Time Machine backups fail with no error message

    My Time Machine hasn't successfully completed a backup since 3/19. It starts the backup on schedule, indexes over 2 million objects, goes through the phase of preparing objects, and then just stops. I know that there have been many changes since that time, but it isn't backing them up. Please tell me how to fix this.

    I have the same problem - Time Machine fails to backup with no error message - after a brief foray into Mavericks. Each time it tries to backup, TM creates a new folder in the "in progress" directory but fails to complete.  Otherwise TM looks normal with no obvious errors. I have several HDDs.  I installed Mavericks on an external drive, migrated my data over to it. Booted from it and after a day or two decided I just didn’t' like it and booted from my Snow Leopard partition.  All was fine but apparently, I had forgotten to turn OFF Time Machine while booted into Mavericks.  Thereafter, Time Machine failed to backup.  Here's what I've done and the error logs:
    Deleted the NEW directory that Mavericks created on TM
    Done a full reset of TM (deleted: /Library/Preferences/com.apple.TimeMachine.plist
    Re-entered the exclusions
    Rebuilt the directory structure on the boot disc using DiskWarrior
    Repaired the TM disc using Disc Utility
    Resynced the Spotlight cache on the boot disk
    TM also seems not to do a deep traversal since it just stops after checking files to backup.
    Here are the error logs from the TM Buddy widget:
    Starting standard backup
    Error loading /Library/Plug-ins/DiskImages/VirtualPCDiskImagePlugin.bundle/Contents/MacOS/Vir tualPCDiskImagePlugin:  dlopen(/Library/Plug-ins/DiskImages/VirtualPCDiskImagePlugin.bundle/Contents/Ma cOS/VirtualPCDiskImagePlugin, 262): no suitable image found.  Did find:\n /Library/Plug-ins/DiskImages/VirtualPCDiskImagePlugin.bundle/Contents/MacOS/Vir tualPCDiskImagePlugin: mach-o, but wrong architecture
    Cannot find function pointer MacDiskImagePluginFactory for factory 7F1FD83E-6684-11D8-968F-000A957703C0 in CFBundle/CFPlugIn 0x102f00930 </Library/Plug-ins/DiskImages/VirtualPCDiskImagePlugin.bundle> (bundle, not loaded)
    Backing up to: /Volumes/Time Machine/Backups.backupdb
    Event store UUIDs don't match for volume: Mac Pro Data
    Forcing deep traversal on source: "Mac Pro Data" (mount: '/Volumes/Mac Pro Data' fsUUID: B4BEA50F-15B1-34BB-92F1-B7605139B852 eventDBUUID: BA019CB5-8123-4C99-9806-C9593D4EFA34), {1, 1, 1, 0}
    Event store UUIDs don't match for volume: Music HDD
    Forcing deep traversal on source: "Music HDD" (mount: '/Volumes/Music HDD' fsUUID: FF1EF8F5-30D0-34C0-BC02-ACDB5AD18B3A eventDBUUID: 92A95F63-5F4A-4987-90DB-5444ADF33D40), {1, 1, 1, 0}
    Node requires deep traversal:/ reason:must scan subdirs|
    Error: Flushing index to disk returned an error: 0
    Backup canceled.
    I don't know what to do next.  Any ideas?
    Thanks,
    John

  • Admin Server satrtup failing with the error User weblogic is not permitted to boot the server

    Hi ,
    The admin server is not coming up , its failing with the below error.
    <May 25, 2014 10:28:35 PM PDT> <Critical> <WebLogicServer> <BEA-000386> <Server subsystem failed. Reason: weblogic.security.SecurityInitializationException: User weblogic is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.
    weblogic.security.SecurityInitializationException: User weblogic is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.
            at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.doBootAuthorization(CommonSecurityServiceManagerDelegateImpl.java:1010)
            at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1054)
            at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:873)
            at weblogic.security.SecurityService.start(SecurityService.java:141)
            at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
            Truncated. see log file for complete stacktrace.
    I have tried resetting the password as per below link , it hasn't helped. Still facing issue. Please help
    http://www.weblogic-tips.com/wls-security/
    Thanks,
    Pradeep

    Creating New user did not help . Still same error.
    <May 26, 2014 8:56:31 PM PDT> <Critical> <Security> <BEA-090404> <User weblogicNew is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.>
    <May 26, 2014 8:56:31 PM PDT> <Critical> <WebLogicServer> <BEA-000386> <Server subsystem failed. Reason: weblogic.security.SecurityInitializationException: User weblogicNew is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.
    weblogic.security.SecurityInitializationException: User weblogicNew is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.
            at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.doBootAuthorization(CommonSecurityServiceManagerDelegateImpl.java:1010)
            at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1054)
            at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:873)
            at weblogic.security.SecurityService.start(SecurityService.java:141)
            at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
            Truncated. see log file for complete stacktrace
    >
    <May 26, 2014 8:56:31 PM PDT> <Error> <WebLogicServer> <BEA-000383> <A critical service failed. The server will shut itself down>"

  • My Time machine backup fails with an error message

    Time machine used to work just fine when I first upgraded to Leopard but now every time it tries to backup I get an Error message "Unable to complete backup. An error occurred while copying files to the backup volume." This occurs while Time Machine is "Preparing". Next hour it starts all over again and does the same thing. I have reformatted the backup drive but still get the error. I'm backing up to a 300g Firewire drive and have used about 207G for the backups.backupdb folder.
    An ideas how to resolve this issue?

    Here is a list of some TM articles that may help. You can look for more by searching Mac Help from the Finder's Help menu or searching the Knowledge Base from Apple's Support Page.
    Time Machine Troubleshooting
    Here are several articles to help troubleshoot Time Machine Problems as well as assist in properly setting up Time Machine.
    Mac 101- Using Time Machine in Mac OS X 10.5 Leopard
    Is Time Machine all you need?
    Some advice for those using Time Machine
    TidBITS Macs & Mac OS X- Time Machine- The Good, the Bad, and the Missing Features
    Mac OS X 10.5- Time Machine backups are not visible
    OS X 10.5- Time Machine stops backing up to external disk
    10.5- Disable the 'use this disk?' Time Machine dialog
    Time Machine tips and troubleshooting
    Mac OS X 10.5 Help- Restoring files backed up with Time Machine
    OS X 10.5- Using Time Machine and troubleshooting Time Machine issues

  • UDI OSD Task Sequences started failing with 0x80070002 error in SCCM 2012

    This is kind of long, but here goes...
    We built a UDI task sequence in SCCM 2012 (with MDT integration) that we were testing for deployment of a couple of different Win7 images.  We customized the UDI experience thru the UDI wizard and XML file and OS deployment worked as expected
    thru the task sequence (testing on Hyper-V VMs). Recently, this UDI TS started failing with error 0x80070002  during what appears to be the "Use Toolkit Package" step.  This is after the OS image has already been laid down and after the ConfigMgr
    client has been installed/configured.  The SMSTS.log reports "Failed to open the task sequence key HKLM\Software\Microsoft\SMS\Task Sequence.  Error code 0x8007002"  Among other errors...I will post the entire log below...
    After the error during deployment, Win7 will boot normally, however, you have no network connectivity and it appears the proper network driver didn't get loaded in the OS. Combine this with the fact that the TS should have joined the machine to our domain,
    but you can't login because no network.. Im not sure if the network issue is a product of the TS failing early or the actual cause of the TS failure. 
    Anyway, I attempted to build another UDI task sequence using the same boot image and toolkit/settings packages, but am experiencing the same error during deployment.  We have a few OSD task sequences built without UDI and those all still work just fine. 
    So, I am at a loss for where the root problem lies.  Any suggestions or assistance would be greatly appreciated.
    Here is the entire SMSTS.log and BDD.log...
    https://skydrive.live.com/redir?resid=D65B1C4362892A26!110&authkey=!AKu5mOvDsXaEgvc
    Thanks
    Richie Tenhet

    your failure does appear to be network (driver or otherwise) or dns related and it cannot contact the management point FQDN just around the time where it should download and execute the
    Use Toolkit Package step...
    "Starting Task Sequence Engine . . . "
    "Non fatal error 0x80072ee7 in sending task sequence execution status message to MP"
    "Start executing an instruciton. Instruction name: Use Toolkit Package. Instruction pointer: 83"
    "unknown host (gethostbyname failed)"
    "sending with winhttp failed; 80072ee7"
    "Tried all the available http based locations. SMB based locations will be attempted now."
    "Failed to resolve the source for SMS PKGID=P0100015, hr=0x80070002"
    "Failed to run the action: Use Toolkit Package.
    The system cannot find the file specified. (Error: 80070002; Source: Windows)"
    that said, check that the package referenced above actually exists and is the correct source version on your distribution points, also verify (press F8 and check can you ping the FQDN of your management point) that you have network connectivity
    around the time of the failure.
    Step by Step Configuration Manager Guides >
    2012 Guides |
    2007 Guides | I'm on Twitter > ncbrady

  • New iphone, restore backup failed with - An error occurred. How do I fix this?

    Have tried to follow the transfer instructions but it does not seem to work.
    Everytime I choose to restore a backup when I set up / activate the new iphone, it fails after some 10-12 seconds with the message that it could not restore because an error occurred.
    It says nothing else about what the error is and I have to start the set up / activation all over.
    So how so I solve this?
    Other 'answers' says how to transfer, but it does not work for me and the answers I have found does not address this issue.

    Search the error code in the support search and you should find something that will walk you through it, but without an error code it's a little hard to know what you're talking about

  • Using Windows 7 Backup (with 3.0 TB drive) the backup fails with an error code of (0x8078002A)

    I have tried for over a month to back up my laptop to a new external 3TB drive (DWC130).  I have reformatted it, changed my windows backup settings, and read as much as I could about this issue and still have had no success.  I have reformatted the drive; I have allowed Windows 7 (64-bit) to back up with its own settings; I have read forums all over and there has been no answer provided that solved this issue.  I am hoping someone from Toshiba or this form can provide some direction.

       Error code 0x8100002F and or error code 0x80070002 when you back up files in Windows 7
    -Jerry

  • BMR-SS backup fails with error "the specified network name is no longer available"

    We are running DPM 2012 SP1 on a Windows Server 2008 R2 system, backing up a Windows Server 2012 system that is a DC.  The agent version is 4.1.3417.0.  Both the DPM server and the DC are physical systems - brand new HP Proliant 360's.
    When creating the replicas for the 2012 server the first time, the backups work fine, and then for a day or so after that.  After a couple of days, the BMR-SS backups fail with the error "the specified network name is no longer available".  
    I can watch the backup happening in the Windows Server Backup console on the protected server - the BMR backup goes up to 99% and then fails.  BMR backups on all the other servers are working - we have a mix of Win2008R2 and Win2012. 
    Here is what I have tried:
    I can connect to the UNC path on the backup server without a problem during and after the backup is happening. 
    Tried reinstalling the DPM agent.
    Tried backing up directly from the protected server to another server's network share, which worked.
    I can copy multiple gigabyte files directly from the protected server to the DPM file share without a problem (the same one that DPM uses for the replica)
    Tried turning off the SCEP real-time protection during the backup.
    Any help would be appreciated - thanks.
    KW

    llo Boudewijn
    I followed Boudewijn's suggestion. 
    The Windows 2012R2 servers had no recovery partition in disk C. I created one (400MB) following http://support.microsoft.com/kb/2930294/en-us and
     DPM system restore worked. But just once. 
    So this is not the solution to the problem......
    Is no one else having issues with DPM bare metal protection of Windows 2012R2 servers? 

  • Hyper-V host fails with "RPC Server unavailable" error when I try to promote Windows Server in virtual machine to a domain controller

    Host: Windows Server 2012 R2 with Hyper-V and RRAS (for Internet over NAT)
    VM: Windows Server 2012 R2 with installed Active Directory Domain Services
    When I open AD DS configuration window (“promote this server to a domain controller”) many services and programs on my host (include Hyper-V, RRAS & Server Manager) fails with RPC Server unavailable error.

    Hello Aleksandr,
    There wasn't any configuration information, ipconfig /all, network setup, etc. So it's difficult to tell.
    More importantly, are you trying to promote the host server? If yes, that is not advised, for one, because it's a Hyper-V server, (not suggested at all), and two, RRAS is installed. RRAS is problematic with any domain controller because it turns it into
    a multihomed domain controller.
    Active Directory communication fails on multihomed domain controllers
    http://support.microsoft.com/kb/272294/
    Multihomed DCs (with more than one unteamed NIC or multiple IPs) with DNS, RRAS, iSCSI, Clustering interfaces, management interfaces, backup interfaces, and/or PPPoE adapters - A multihomed DC is not a recommended configuration, however there are ways to
    configure a DC with registry mods:
    http://blogs.msmvps.com/acefekay/2009/08/17/multihomed-dcs-with-dns-rras-and-or-pppoe-adapters/
    7 Reasons not to Make Hyper-V a Domain Controller
    http://www.altaro.com/hyper-v/reasons-not-to-make-hyper-v-a-domain-controller/
    Domain Controller as Hyper-V host
    https://social.technet.microsoft.com/Forums/windowsserver/en-US/4ff14bec-a815-473b-8d2a-33e91e17197b/domain-controller-as-hyperv-host?forum=winserverhyperv
    Networking?
    I don't know how your networking is setup, whether there are multiple NICs on the host server, if they are teamed, if you have the host interface set to allow the operating system to share administration, or if there are separate interfaces for each. Can
    the host OS ping/communicate with the DC virtual machine?
    If there are more than one NIC, you have the choice to team the NICs and share the Teamed NICs for the Hyper-V OS and the VMs, or keep them separate where one is devoted for the Hyper-V OS, and one for the VMs.
    Hyper-V Server VLAN Network Configuration
    https://social.technet.microsoft.com/Forums/windowsserver/en-US/0aa71d2a-ebf9-4a3e-bbf5-94db55339fa2/hyperv-server-vlan-network-configuration?forum=winserverhyperv 
    Recommendation:
    Why not just create another VM DC?
    Ace Fekay
    MVP, MCT, MCSE 2012, MCITP EA & MCTS Windows 2008/R2, Exchange 2013, 2010 EA & 2007, MCSE & MCSA 2003/2000, MCSA Messaging 2003
    Microsoft Certified Trainer
    Microsoft MVP - Directory Services
    Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
    This posting is provided AS-IS with no warranties or guarantees and confers no rights.

  • Backups fail with Insufficient privileges error

    Oracle 9.2.0.5 database
    Solaris Operating Sysstem
    I needed to recreate one database recently from the backup. I used DUPLICATE TARGET DATABASE comamand to recreate database. And once client confirmed I removed old database and copied this new database to original location and recreated controlfile.
    But the tape backups are failing ever since then.
    Is it because of password file problems ? This is a a totally new database and also DBID is different . But database name is same and created from backups of old database.
    Backups fail with this error.
    RMAN-00571: ===========================================================
    RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
    RMAN-00571: ===========================================================
    ORA-01031: insufficient privileges
    But the RMANUSER has the same privileges as in other databases on this server.
    SQL> select username,sysdba,sysoper from v$pwfile_users;
    USERNAME SYSDB SYSOP
    SYS TRUE TRUE
    RMANUSER TRUE FALSE
    SQL> select privilege from dba_sys_privs where grantee='RMANUSER';
    PRIVILEGE
    CREATE SESSION
    UNLIMITED TABLESPACE
    How to resolve this issue ?

    I actually recreated the password file using orapwd utility. But when checked the V$PWFILE_USERS it showed no users. Not even SYS
    And I tired to grant SYSDBA to RMANUSER. It failed with the following error.
    ERROR at line 1:
    ORA-01999: password file mode has changed from 'exclusive' to 'shared'
    But the show parameter REMOTE showed that remote_login_passwordfile is still EXCLUSIVE. And database uses an INIT file, not SPFILE.
    I had to move back the copy of Old password file and now it shows two users (SYS and RMANUSER) again.

Maybe you are looking for