Base on Power up reset error

Hello!
I would like to ask a question. my motion controller after i put web browser program in it, it Red LED light up, that means got fault. now I can not find what is the fault. it said montion controller in Power Up Reset status, I can't clear it. after I initiallise it still not working. sometime it will generate a error code is 70072.
Really need help. Got any solution to clear Power up reset status?
Thank you!
Kuroro

Hi Kuroro,
Thanks for posting on the forum, we will certainly do our best to help you out!
The Power up reset error can typically be cleared in several different ways. First, it is often possible to clear this error by going to Measurement and Automation Explorer and Initializing your Motion controller hardware. When this doesn't help, sometimes the best way to clear this status is by running a LabVIEW VI that contains nothing but the "Clear Powerup Reset Status" VI. This VI can be found on the LabVIEW palette at All Functions>>NI Measurements >> Motion >> FlexMotion >> Advanced >> Clear powerup reset state.vi.
One of these two things will hopefully resolve the problem you are experiencing. I am not sure what you mean when you say that you put a web browser program on your motion controller, but if you have any other questions, feel free to ask. As always, the more information the better!
Hope this helps,
Robert

Similar Messages

WRT54G V3 Web Gui recieves "connection reset" errors on all pages

Hello,
I was recently having some connection problems with my WRT54G and decided to upgrade the firmware. The router has been stable for quite some time before the last week. The firmware was from linksys and it uploaded fine and rebooted and all was great.
When I tried to reconfigure the router settings I ran into trouble. None of the html forms will submit. All of them get "connection reset" errors when I try and update the information. Apparently there was an error in flashing or something. So I think, no prob, I'll just re-flash. Except that the firmware upgrade form also gets connection reset.
If I type in 192.168.1.1/apply.cgi it works...no connection reset (though nothing comes out). I have a hunch that if I were able to custom form the HTTP post header it might go through.
I tried TFTPing the new firmware to the router and had no success. Granted I am a mac user so I was in the terminal window instead of using the proprietary tftp util. I always get "transfer timed out" errors. I tried starting the transfer before the router responded to a ping, after, before the power light started flashing, after that, and after it went solid too.
Any help is appreciated. Thanks.

Try to update firmware using TFTP program from a windows based PC. You can get tftp from ftp://ftp.linksys.com/pub/network/

How to clear power up reset states?

Hi everybody,
I'm facing a problem with the motion control system, the system kept contiune showing us that the system is in power up state. we run the clear power up reset state program but we still could not solve the problem. Is there any other solution to provide me to solve this problem. what are the problem that actually cause this error state? this problem dose it related to our hardware connection or software setting?
thanks for helping.. really need the help...

Hey Kuroro,
Usually when you call and run the clear power up reset state program, it should take care of resetting the state of the board. The next step to try is after you have run the clear power up reset state is to initialize the board itself. Go ahead and try to reinitialize the board after you call this clear power reset state program. You can either initialize the board in the Measurement and Automation Explorer, or you can use the function in Labview to do this. You can just use the Initialize Controller VI to do this.
Please let me know if this works or not. Usually initiallizing the board after calling the Clear Power up Reset State VI solves the issue. Keep me updated on what else is going on, i.e. what errors you are seeing or what else is going on with the hardware. Thanks, and have a great day.
Regards,
DJ
Applications Engineer
National Instruments

Unable to open Power BI Sites - Error: We were unable to load the Site. Refresh the page to try again

Power BI Sites Error
We were unable to load the Site. Refresh the page to try again
When opening Power BI Sites with internet explorer, in certain security configurations you may run into the above error. While we are looking into resolving this, please see the following workaround:
From the Tools menu, select internet options.
On the security tab uncheck the "Enable Protected Mode" checkbox form the relevant Zone (Intranet/Internet)
Remove all entries to *.powerbi.com from trusted sites or/and local intranet sites
On the advanced tab, uncheck the "Enable enhanced protected mode" (if you made a change here it will require a restart of the machine)
Restart and try again (if not changes done in the last step, just restart the browser)

Hi
Any further debugging tips? I upgraded from IE9 to IE11 on my Win7 machine to try get Q&A working, it broke the entire PowerBI site for me

IPod shuffle Reset Utility Reset Error

My ipod shuffle (1st gen) is not shown in itunes or finder.
I have tried all the following already:
1) Switching usb ports
2) Turning on/off ipod
3) restarting computer
4) reinstalling itunes
I followed the directions for Reset Utility. My ipod was found by the utility, but results in a "reset error" everytime (multiple restarts already tried).
Worked fine until I used the ipod to transfer data to a pc. I've done this multiple times w/o a problem. This time, the ipod was incompatible with windows (itunes updated on that computer, too). Don't know if this matters.
None of the lights come on. Does not appear to be charging. The ipod shows no life.
It is no longer under warranty.
Please help or I'll have to listen to the radio in my car.
ibook g4 Mac OS X (10.4.8)

I did not touch my shuffle for 3 days, tried it in my computer again, and it still failed. All the same problems. No lights and none of the programs acknowledged it, except the reset utility, which gave me the same error message.
So, I returned here, praying for answers. Nothing. For some reason, I tried turning the ipod on, and BOOM, I got a green light and it seemed okay. Tried it in my computer again, and now it works! I've reset it anyway (through itunes), and all seems well.
I guess time does heal all wounds. Thanks to everyone who tried to help. Assume all worked out unless you hear from me again.
No more radio for me! (again)... yeah.

Firefox connection was reset error for a long request

I have a web service api which takes 5 minutes to respond a JSON response message.
In firefox (version 32.0.3), I get a "The connection was reset" error after 2 to 3 minutes.
When I call my call my API in Chrome, there is no error and I get the intended response after 5 minutes.
I have tried the following without any luck:
1. tweaking timeout values in about:config
2. clearing browser caches
3. setting "No proxy" in network settings
4. disabling ad-ons and starting in safe mode.

I tried it with Firefox 29 and even 22, still after 3 minutes it just gives a connect reset.
Also, to provide more context, I am making a REST API call whih takes 5 minutes to respond. When I deploy the application on localhost, it (firefox) does not give a connect reset error and completes. But, when I deploy it on a remote server, it gives this error.

"The Connection was reset" Error while attempting to load Hotmail

I've had Hotmail for a few years now and never had a problem with it. A couple of days ago when I went to check my mail it stopped working and I got the "The Connection was reset" error (See attached picture). I've tried deleting everything (Browsing & Download History, Form & Search History, Cookies, Cache, Active Logins, Offline Website Data, Site Preferences), and it still doesn't work. I'm not running any add-ons/plugins or firewall software. I've tried running Firefox in safe mode and tried uninstalling and reinstalling and nothing is working. I've even tried on Google Chrome and Internet Explorer and I'm getting the same errors. Ideas?

For some reason the image didn't post or I'm just to dumb to find it but here's the words:
<blockquote>"The connection was reset
The connection to the server was reset while the page was loading.
The site could be temporarily unavailable or too busy. Try again in a few moments.
If you are unable to load any pages, check your computer's network connection.
If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web."</blockquote>
Also I forgot to add I can access it from my phone and from my laptop it's just my desktop which doesn't load it. I can also ping www.hotmail.com and everything indicates normal. I can access all other sites from my desktop it just wont load hotmail.

Ace - connection reset (Error 101)

Hi, I have a problem with a Cisco ACE, after approximately an hour being in production, for all new connections
it gives the message: connection reset. The message on any web browser is: connection reset (Error 101)
It blocks any backend server (Apache).I get same error also when I try to connect direcly to the backend address.
This error saturates the connections on the servers (in the log of the DB I found error connection reset)
Without ACE all work fine, it's not a load traffic issue.
It seems like once opened a connection the ace does not close it anymore!
But the graphical snmp servers do not report the increase in connections, what is mistake ?
The balancer manages two physical servers and is configured in stickyness mode
Please find attached the configuration
logging enable
logging timestamp
logging trap 4
logging buffered 3
logging host 172.16.0.2 udp/514 format emblem
access-list ANY line 8 extended permit icmp any any
access-list ANY line 16 extended permit ip any any
probe http HTTP_PROBE1
request method get url /index.php
expect status 200 206
expect status 300 307
expect status 400 417
probe tcp PROBE_TCP
interval 30
rserver host 03a.it
ip address 172.16.0.1
conn-limit max 50000 min 40000
inservice
rserver host 03b.it
ip address 172.16.0.2
conn-limit max 50000 min 40000
inservice
serverfarm host FARM_WEB
predictor leastconns
probe HTTP_PROBE1
rserver 03a.it
    inservice
rserver 03b.it
    inservice
parameter-map type http HTTP_PARAMETER_MAP
persistence-rebalance
sticky http-cookie session StickyGroup1
timeout 3600
serverfarm FARM_WEB
class-map type management match-all ICMP-ALLOW_CLASS
2 match protocol icmp source-address x.x.x.x
class-map match-all L4-WEB-IP
2 match virtual-address x.x.x.x tcp eq www
class-map type management match-all REMOTE_ACCESS
2 match protocol ssh any
policy-map type management first-match REMOTE_MGMT_ALLOW_POLICY
class REMOTE_ACCESS
    permit
policy-map type loadbalance http first-match WEB_L7_POLICY
class class-default
    sticky-serverfarm StickyGroup1
    insert-http x-forward header-value "%is"
policy-map multi-match WEB-to-vIPs
class L4-WEB-IP
    loadbalance vip inservice
    loadbalance policy WEB_L7_POLICY
    loadbalance vip icmp-reply active
    nat dynamic 1 vlan 2541
    appl-parameter http advanced-options HTTP_PARAMETER_MAP
interface vlan 125
ip address
access-group input ANY
service-policy input REMOTE_MGMT_ALLOW_POLICY
service-policy input WEB-to-vIPs
no shutdown
interface vlan 254
ip address
access-group input ANY
nat-pool
service-policy input REMOTE_MGMT_ALLOW_POLICY
no shutdown
At the moment this happens, the simultaneous connections (command: show conn) on the server are around 350
the CPU load is 2%
sticky database has approximately 24000 records.
Log level is set to 4. But no error report.
Do you need more info to resolve the problem?
Thank you
Best Regards
N.

Hello Nicolas,
I wonder if you can include these values:
parameter-map type http HTTP_PARAMETER_MAP
case-insensitive
persistence-rebalance
set header-maxparse-length 65535
set content-maxparse-length 65535
length-exceed continue
parsing non-strict
I also noticed a lot of errors which might be caused also due to these denied under the #show resource usage all which may indicate you are reaching the license limits, but you should discuss it with your Cisco SE, please see below:
                                               Allocation
        Resource         Current       Peak        Min        Max       Denied
Context: vrack254
conc-connections              4       1267      60000      60000          0
mgmt-connections              2         28        748        748          0
proxy-connections             0       1255       7864       7864          0
xlates                        0          0       7864       7864          0
bandwidth                   572    3824781    3740624 127490624    1416859
    throughput                 96    3712886    3740624    3740624    1416859
    mgmt-traffic rate         476     111895          0 123750000          0
connection rate               1       1729       4500       4500          0
ssl-connections rate          0          0        224        224          0
mac-miss rate                 0         15         16         16          4
inspect-conn rate             0          0       1800       1800          0
http-comp rate                0          0    5898240    5898240          0
to-cp-ipcp rate               0         11         36         36          0
acl-memory                 8216      10568     744800     744800          0
sticky                    22978      22978      31456      31456          0
regexp                       19         23       7864       7864          0
syslog buffer             30720      30720      30720      30720          0
syslog rate                   0          6        750        750          0
Can you upload the specific error which you are getting also?
Jorge

WRT54G Disconnects and REQUIRES a Power on Reset

My WRT54G disconnects once per day and requires a power on reset to get it back on line. It's version 6 with the most recent firmware.
After a wonderful chat session with Linksys this AM and then a subsequent email to Support, I've received NO satisfaction.
Anyone have a suggestion as to a solution???? I'm at my second warning and about to be banished!!!!
The router crashes each and every day and it seems to be DIRECTLY related to how much the kids use the wireless connection - you see they were gone for two weeks and there were NO (ZERO) crashes, they came home and started to use the wireless connectivity and BINGO, I'm pulling the plug on the WRT faster than OnnagokorO and his cohorts can edit/delte my posts.
Please, please tell me there's an answer.
(Edited a small part post for guideline compliance. Thanks!)
Message Edited by OnnagokorO on 04-10-200705:35 PM
Message Edited by dtv on 04-10-200707:11 PM

To dtv --- my guess is that the kids are running some high bandwidth program that makes multiple simultaneous Internet connections. This tends to use a lot of memory in the router, causing it to crash. Many programs can cause this, but it is common in peer to peer networking programs, such as BitTorrent.
If this is the case, limit the number of simultaneous connections that BitTorrent can make.
Please also note that Linksys recently posted a firmware upgrade that should help with BitTorrent problems.
Message Edited by toomanydonuts on 04-10-200711:25 PM

I have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

i have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

Read the user guide:
http://support.apple.com/manuals/#airport

IDVD5 and Power Calibration Area Error

In an effort to burn a Maxell DVD-R from iDVD, I receive the following error message just as the burn process completes:
The recording device reported the media error: Power calibration area error. (0x73, 0x03.)
1) I visited the Apple Store and the genius ordered and installed a new dvd burner
2) The new burner has the exact same error
3) I've search around the internet and realize that I'm not alone. Aparently many have seen iDVD show this error with one unusual means to fix the error. One fix was to burn the image to an external drive and then use the disk utility to burn the dvd. Apparently the issues seemed to be iDVD.
4) I've burned many DVDs with the same project to the same brand of DVD-R in the exact same manor that I tried here.
5) I have iDVD 5.0.1, a new Powerbook 15", and OS X 10.4.2.

I still have the same problem with iDVD 5, Toast 7 Platinum, DVDSP, and even recording my project into a .img file and using Disk Utility, so I don't think the problem is related to a particular app, but to Mac OS X, and not even a hardware or media problem as I've previously used this brand to burn like 50 DVDs without problems (Verbatim DVD-R) and in two days I've had like 15 coasters with this project with both Verbatim and Samsung DVD-Rs.
Here is the error log:
iDVD: Burn started, Fri Dec 30 20:38:24 2005
iDVD: Burning to DVD-R media with DAO strategy in PIONEER DVD-RW DVR-104 X227 via ATAPI.
iDVD: Requested burn speed was 1x, actual burn speed is 1x.
iDVD: Burn underrun protection is supported, and enabled.
iDVD: Write (10), block: 768, count: 64 -> 3/0C/00 Medium Error, Write error
iDVD: Burn failed, Fri Dec 30 20:39:56 2005
iDVD: Burn sense: 3/0C/00 Medium Error, Write error
iDVD: Burn error: 0x8002006E The burn failed because of a medium write error.

Error Code When Burning (Power calibration area error. (0x73, 0x03.)

I've been searching for answers to my problem and it seems like this problem has randomly popped up for many others like it has for me.
A month ago I randomly started getting this error code Power calibration area error. (0x73, 0x03.) when I tried to burn dvds in DVD Studio Pro. When I try to burn a DVD just from the finder options I get this error Code (Error code 0x8002006D)
But CD's burn fine for me.
I have been using the exact same discs that were able to burn before. They are 16x speed Memorex.
I tried relaunching the finder. I bought a Disc Cleaner today and i bought some 8x speed DVD's. I cleaned the Burner and I was able to successfully burn a 8x cd but still not the 16x.
Does anyone know the cause of this error code? Why would it just randomly happen?

Hi:
Check this thread:
http://discussions.apple.com/thread.jspa?threadID=1054119
You can use this link ** Media Brand vs. Manufatrurer Brand ** to learn about your media quality.
Hope that helps !
Alberto

Power calibration area error. (0x73, 0x03.) for my DVD burner

My dvd drive was working just fine then the other day I went to burn a dvd using idvd studio pro (like I always do) and it started burning, then about 2 minutes into the burn I got an error message stating that the burn failed due to a "Power calibration area error. (0x73, 0x03.)" then th disk just spit out of the drive. I dont know what this is or how to fix it. can anyone help??

Welcome to the discussions!
Usually this pops up when your drive does not like the disk itself. Try either a different blank or a different brand disk.
I use only TDK and Fuji disks and I have never received that error and never burned a bad disk either.

How to clear the power up reset states

my pci 7344 is in the power up reset state. How to clear the power up reset state of an 7344 programmatically. Using clear power up reset state in block diagram doesnt seem to work. Give a possible solution

This is the VI I use to initialize a motion controller. It clears the power up reset if needed and then initialize the controller with the specified configuration (previously created with MAX).
Sorry for the french comments.
Attachments:
Initialiser interface avec gestion power up reset (LV8).vi ‏26 KB

Connection reset error

we wrote a proxy that should handle request from the browser and deliver it to the parent
but when we read from the parent after we read the first chunck of data and send it to the client we get connection reset error(SocketException)
what should we do?
here is out code thanks
          Socket parent = null;
          PrintStream streamToParent = null;
          InputStream streamFromParent = null;
          try{
               parent = new Socket(parentHost, parentPort);
               //1- forword the request to the Parent ans read the response
               streamToParent= new PrintStream(parent.getOutputStream());
               streamToParent.write(reqStr.toString().getBytes());
               streamToParent.flush();
               streamToParent.println();
               streamToParent.flush();
               int bytesRead = -1;
               byte[] response = new byte[4096 ];
               //1a- extract Headers - (of response)
               StringBuffer headers = new StringBuffer();
               int byteRead = 0;
               streamFromParent = parent.getInputStream();
               while (!endOfHeaders(headers) && (byteRead = streamFromParent.read()) >= 0) {
                    headers.append((char) byteRead);
               //1b- check headers
               boolean toBeCached = checkResponseHeaders(headers);
               if(toBeCached)
                    System.out.println("cachedMe: " + url.toString());
               HttpResponseHeader resH = new HttpResponseHeader(headers.toString());
               String etag = resH.get("ETag");
               String lastM = resH.get("Last-Modified");
               String expires = resH.get("Expires");
               Date expDate = null;
               OutputStream osBody = null;
               byte[] bHeaders = headers.toString().getBytes("US-ASCII");
               if(expires != null)
                    expDate = new Date(new HttpDate(expires).getAsLong());
               //1c- write the headers to the client
               OutputStream streamToClient = client.getOutputStream();
               streamToClient.write(bHeaders);
               streamToClient.flush();
               //1d- continue with the body, read from parent and write to client
               try{
                    if(toBeCached)
                         osBody =_wcdb.insert(url, expDate , lastM, etag, bHeaders);
                    int sumInsert = 0;
                    while ( (bytesRead = streamFromParent.read(response)) >= 0 ) {
                         streamToClient.write(response, 0 , bytesRead);
                    streamToClient.flush();
               catch(IOException ioe)
          catch(IOException ex) {}
          finally
               if(streamToParent != null)
                    streamToParent.close();
               if(streamFromParent != null)
                    streamFromParent.close();
               if(!client.isClosed())
                    client.close();
               if(parent != null)
                    parent.close();
          }

What 's the 'parent'?
The exception usually means that the end you are writing to has already closed its socket. What's the full text of the exception?

Base on Power up reset error

Similar Messages

Maybe you are looking for