Base station does not show in airport utility

How do you display a base station in the airport utility?

Sorry, but an "older" one does not tell us much about which model that you have....since there are about a dozen different base stations which might be called "older", and the tips and tricks are different depending on what model that you have.
If you do not know the model number, please look on the bottom of the base station. The model number starts with an "A" followed by four numbers. Depending on what model that you have, It might be found on a label, or it might be embedded in the foam pad. Post back with the model number.
You did not answer our question regarding what version of AirPort Utility that you are using. We need that information to be able to help. If you have a Mac, open AirPort Utility and click on the AirPort Utility menu in the upper left corner of the screen, then click About AirPort Utility and post back with the version number that you see there.

Similar Messages

Airport Extreme base station does not appear in Airport Utility

I cannot see the basestation that I am connected to via WIFI or Ethernet. I cannot see the basestation on ipad or iphone app either. Basestation is working fine and i have connection working fine with a green light but cannot configure the basestation to allow guest networks or connect my external storage drive.
any suggestions will be appreciated.

OK. That should be a third or fourth generation Extreme, plenty new enough. (The most recent OS X and iOS versions of AirPort Utility cannot configure the original Extremes, but they can handle my mid-2007 second generation Extreme.)
If two or three devices on the same network as the Extreme cannot "see" the configuration interface, I would guess that the problem lies in the Extreme itself.
Have you tried power cycling the Extreme?
Did you purchase AppleCare for your 2011 MBP? If so, and if you bought the Extreme less than two years earlier, the AppleCare should cover the Extreme also.

Time Capsule base stations does not appear in AirPort Utility

I can't see my Time Capsule in Airport Utility 6.3.2. on Mavericks. And I can't access the Data volume for Time Machine Backup. The Internet is working!
However I can see it the Time Capsule on my iPhone's Airport utility.
I have tried rebooting Time Capsule a few times, didin't help.

OK. That should be a third or fourth generation Extreme, plenty new enough. (The most recent OS X and iOS versions of AirPort Utility cannot configure the original Extremes, but they can handle my mid-2007 second generation Extreme.)
If two or three devices on the same network as the Extreme cannot "see" the configuration interface, I would guess that the problem lies in the Extreme itself.
Have you tried power cycling the Extreme?
Did you purchase AppleCare for your 2011 MBP? If so, and if you bought the Extreme less than two years earlier, the AppleCare should cover the Extreme also.

I have airport express but it is not recognised by either my macbook pro or my ipod on my wireless network. It does not show in airport utility. Might I not have an airport card?

I have airport express but it is not recognised by either my macbook pro or my ipod on my wireless network. It does not show in airport utility. Might I not have an airport card? How would I know. Airport utility in my mac says no other devices connected.

I have airport express but it is not recognised by either my macbook pro or my ipod on my wireless network. It does not show in airport utility. Might I not have an airport card?
If both your MacBook Pro and iPod are unable to "see" the Wi-Fi network provided by the AirPort Express, it is most likely NOT that you are missing an "airport card," but the Express may be the issue instead.
One quick test is to see if either device can "see" other Wi-Fi networks. If they can, then you can definately rule both of them out as the issue.
By default, the AirPort Express will broadcast an unsecured Wi-Fi network with a network name of something like: Apple Network NNNNNN. Can either device see this network? If not, then I would recommend that you perform a "factory default" reset on the Express, and then, check again.

USB Drive not showing in Airport Utility

I have a USB HD formatted with Mac OS Extended (journaled) which I plugged in to my Airport Extreme and it does not show in Airport Utility. Any ideas?
Thanks,

Power off the entire network
Wait a few moments
Start the modem first and continue starting devices one at time until everything is powered back up
If the drive still does not show up.....and you are not using a powered USB hub....that may be needed
Other stuff....verify that the USB cable is working correctly

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
Power off the AirPort by pulling the power cord
Wait a minute or two
Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
Release the reset button and allow a full minute for the AirPort to restart
Now try to configure the AirPort again. If you continue to see the same symptoms as before, the AirPort will need to be replaced.

Steady green light on A1084. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it. Is there a fix?

Steady green light on A1084. Mac OS X 10.7.5. IMac. Verizon DSL Actiontec GT704-WGB modem. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it and send a signal to airport express to play airtunes through my stereo amplifier. Is there a fix?

I plugged a model A1034 Airport Extreme Base Station into the Verizon DSL Actiontec GT704-WGB modem with an ethernet cable and now the AirPlay icon appears in the Itunes window immediately to the right of the volume control and I can select it and play Airtunes wirelessly through the A1038 Airport Express Base Station in another room connected to a stereo amplifier by a Monster mini-to-RCA left/right audio cable running from the output jack on the A1034 Airport Express Base Station into the CD jacks on the amp. The problem is that I have to select the Apple Network Airport Express Base Station as my network in order to select the Airport Express Base Station when I click the AirPlay icon, which means I have no Internet signal to the Imac. If I select the Airport Extreme Base Station or the Verzion modem as my network, then I have an Internet signal to the Imac, but the Airport Express Base Station is grayed out when I click on the AirPlay icon, so I cannot select the Airport Express Base Station and send tunes to the Airport Express. It would be nice to play Airtunes while simultaneously accessing the Internet. I don't understand your question about what program I am using for which I require AirPlay. I am not learned about computers in general, and even less so about Macs than PCs. I thought the program I was running was Itunes, and there was no separate program to run to use AirPlay for the purpose of sending a signal from the Itunes on the Imac to the A1084 Airport Express base station in a another room, and then out as described above to the stereo amplifier to listen to Itunes music remotely in the other room, without any kind of cable, wire, etc., connecting the Imac to the stereo amplifier. I would guess that the most common use for the A1084 is to play Itunes through a stereo in another room without the need to run wires from the computer to the stereo. I realize it would be easy simply to run a very long mini-to-RCA left/right audio cable across the floor connecting the Imac to the amp without the need to use AirTunes, Airplay or any kind of AirPort, but it would be both unsightly and a tripping hazard.

Airport base station does NOT deliver a solid connection!

I have an older Airport base station (an extreme-square, flat, white, you know the one). Ever since I installed the most recent firmware update I get next to no data flow through from the provider. If I connect direct to the provider router via ethernet cable I get amazing connectivity speeds. I change the set up to connect via the Airport and I get either no connection or 5 KBS.... a speed, when it available is a joke. While trying to run through the Airport my Airport signal is full strength. It appears the base station does not know how to digest and dispense the information from the service provider into a full band of connectivity. The problem exists with both Apple laptops in the house. I have done all the required resets and restarts and to no avail. Connecting direct, which is a HUGE hassle, provides amazing speeds. I had none of these issues before I did the firmware update about three days ago (about 12.18.09). Any thoughts or directions to help me out?
Thanks!

Your Express requires an IP address to be issued by the device connected to its WAN port, in most cases that is a cable modem.
Power down your modem and let it rest. Leave it powered down, connect it to your AirPort Express, then power it back up again. This permits the modem to supply the Express the IP address it needs.
Like it says, if you still can’t connect, contact your Internet service provider.

Thunderbolt WD Duo, does not show in Disk Utility

Hi Have imac 27 (late 2012) with 10.8.3 update OSX. Connecting to WD Thunderbolt Duo, the disk does not show in disk Utility, sys log or in any connection to the system. WD utility does not seems it either. Restart does not help. By disk returning to seller, the disk works fine on other comp (with the same cable, with the same power adapter)
Is there any issue known with the thunderbolt ports? Tried both all found on internet, but no resolution, to my issues.
Seems to be my imac hardware or maybee the software (thunderbotl 1.2) update.
Lukas

All thunderbolt port tried, cable exchanged, no change
I have done following procedure , no change
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

Time Capsule does not appear in AirPort Utility after Yosemite upgrade

Just upgraded to Yosemite and the Time Capsule appears as a shared device in Finder, but does not appear in AirPort Utility. Any solution to this so I can manage my Time Capsule again?

I'm having the same problem. Did you reset your Time Capsule to factory settings or simply restart it?

Airport Extreme Base station does not 'see' Airport w/Airtunes. HELP!

I just purchased and installed an Airport Extreme Base startion (802.11n), and it does not 'see' my Airport Extreme with Airtunes. I have already tried re-setting the Airport + Airtunes to the factory settings, but since I installed the new Base station software, I no longer have the Airport Express Sett up assisstant?!?
What am I doing wrong?

Your Mac won't be able to communicate with your Airport Express until you reconfigure your Airport Express to join the wireless network now being created by your new Airport Base Station.
The "Airport Setup Assistant" has been replaced by the "Airport Utility". You can find that new utility installed in your Mac's Applications->Utilities folder.
What you should do now:
1. do an factory default reset of your Airport Express.
2. plug the Airport Express (temporarily) into power in the same room as your Base Station and your Mac.
3. on your Mac, run the Airport Utility. It should "see" your Airport Express. Click on the Airport Express icon, click to continue (your Mac will switch wireless networks temporarily), click Continue, and follow the instructions for configuring the Airport Express so that it "joins" the existing wireless network created by your Base Station.

AirPort Extreme Base Station is not Available in AirPort Admin Utility

I don't see my APEX Base Station in the list in AirPort Admin Util. I can configure by opening by IP. I have no software firewall. I have plugged in directly to base station, and have reflash with 5.7 firmware. I am using 4.2 of AirPort Admin. I've Tried everything I can find in forums. Anyone else have issues?
I'm using Mac OS 10.4.4

I have tried resetting it. It doesn't always work. Sometimes the base station is listed, and sometimes it is not. The base station is functioning though. I can access the newtork, It just doesn't show up in Admin Util.
I also have an AP Epress connected to AP Extreme via WDS. From the wired side, they either both show up or both do not, which is expected. When they don't show up on the Admin list, the Express also doesn't show up in iTunes from the wired side. Wireless clients don't seem to exhibit this problem.

Airport extreme does not appear in airport utility and will not reset

Hi,
Here's the problem: My base station wasn't letting me reconfigure its settings via ethernet or airport. I unplugged all cables and performed a hard reset. Now, it will not appear in airport utility either on ethernet or wireless, and it will not revert to the factory 'Apple Network #######' broadcast. It is still showing the name of the previous network in my computer's airport settings. Also, running iStumbler, it too does not see a new network.
Question: Is it fried? If not, what should I do?
Thanks.

I'm may be having the same problem:
Airport Utility doesn't find the base station, despite being connected with ethernet and even now while I'm actually connected to the internet through it via Airport. In my first experience, I reset the base station, and then it did show up, though, as you said, not reset to factory defaults. On another occasion, it wasn't showing up again, but did the next morning when I sat down. Weird. This is on an Alum. PB 15" running Tiger (10.4.11). I also just got an Oct 08 MBPro with 10.5.5 and it's copy of Airport Utility is finding the base station right now while this machine is not. Is this some kind of bug? Both copies of Airport Utility are 5.3.2 (532.8)

Apple express does not appear in airport utility

I have an airport base station (extreme) that is already set up and working fine. However, we needed to extend it's range to a separate guest house so I purchased an Apple Express. When I initially attempted to set it up - I launched the Airport Utility window - it appeared and walked me through the set up. However, it now doesn't appear in the Airport utility window, nor is it functioning (not showing up on any of our computers). I attempted a reset several times but it no longer appears in the Airport Utility window. Any suggestions or ideas about what the problem is? Thanks.

Which version of AirPort Utility are you asking about here?
If you are not sure, open AirPort Utility and click on the AirPort Utility menu at the upper left corner of the screen.
Click About AirPort Utility and post back with that info.
In the meantime, move the the Express to the same room as the AirPort Extreme
Power up the Express and let it run a minute
Hold in the reset button for 9-10 seconds on the back of the Express and let it restart

Airport Express not showing in Airport Utility, flashing Amber

I have 3 Airport Express units. Two of the 3 work fine and show up in Airport Utility v.6 , but the third flashes amber and is not recognized in Airport Express. I have tried soft and hard resets, and it always goes to a flashing amber light and is never reocgnized by Airport Utility.
If I pull down the Wifi icon and go to Airport Express, I get the following window:
Any ideas would be appreciated.

The screenshot is still not coming through here.
Sorry, but I am not familiar with any of the model numbers that you have posted. North and South American versions of the older Express models will be A1084, A1088, or A1264. The newest version of the AirPort Expess is A1392.
Regardless of the model number, all that you can really do is power up the Express for a few minutes, and hold in the reset button on the side of the device for 10 seconds. Then, release the reset button and allow a full minute for the Expess to restart to a slow, blinking amber light.
If you still cannot "see" the Express in AirPort Utility, you either have a defective Express or a much older version that is not supported by AirPort Utillity 6.x.

Base station does not show in airport utility

Similar Messages

Maybe you are looking for