Basic configurations for running BPM in portal

Hi Experts,
I am new to BPM. I have CE server installed and ready how to configure that to run the BPM flow in portal i have created user and assigned the required roles but the problem is still i can't see my tasks in UWL. Basically i want to get the tasks from BPM to UWL. Do we need to deploy any ear or sca for that. what roles are required to get the tasks and what configurations are need to setup. Please help.
Thanks & Regards
Jeetendra Choudhary.

Hi Jeetendra,
In your process you can define the potential owners for a task by navigating to:
Open the Task > Go to User Roles Tab > Specify the Potentia Owners > You have the possibility of Choosing a user or a role here.
You need to be connected to the CE Server in order to get the lis of available users/roles from UME.
Hope this helps!!
Regards,
Arafat

Similar Messages

Best Configuration for running adobe Premiere Pro CS3

I have a 4 HDD system and the ability to run RAID. What is the best configuration to run Adobe premier pro CS3. I want to be able to get the best perfomance out of my system.

Is it possible to run different RAID combination using the same controller card?
For example:
1) 2 HDDs, RAID 0 configuration for Operating System/Programs
2) 2 HDDs, RAID 0 configuration for Project/Scratch Disk/Paging
3) 2 HDDs, RAID 0 configuration for Media/data.
I have a Asus Striker Extreme Motherboard.

Basic configuration for Wireless AP

I have been task to configure and deploy 3 access point in three site within our organzation. I need a little help with this task in order to have it complete by Friday. The model we are using is a Air-Sap1602i-A-K9. Thank you for your time.

Please refer to the following links:
https://supportforums.cisco.com/document/61936/autonomous-ap-and-bridge-basic-configuration-template
http://www.cisco.com/c/dam/en/us/td/docs/wireless/access_point/15_2_4_JB/configuration/guide/scg15_2_4_JB3a.pdf?mdfid=284366503

Issue with Service Group Configuration for a BPM Process

Hi,
I am working on BPM processes on CE 711. I need to use the Service Group settings. I created a BPM process with a automated activity that maps to an enterprise service in HU2 (SAP ES Workplace system).
After setting up the configuration in NWA for service registry and service group, I run the BPM process. The Enterprise Service runs into error and log records it as 'No matching BindingData is found for SOA smart configuration'. I have done most of the configuration as recommended but the matching end point
url seems to be picked wrongly [http://erp.esworkplace.sap.com/sap/bc/srt/xip/sap/ecc_employeebasicdbyemployeeqr?sap-client=800] .
I could not get any info on notes search and could not get much info about service group config. Any help here is greatly appreciated.
Regards
Suresh

Hi Suresh,
i just got an answer on my ticket. Here it is:
There is a known issue with the upper case of the endpoint published in
the Services Registry and in the WSDL.
Before SP2 the matching for the binding for invocation is done
by the endpoint url. There is a known issue that the endpoint published
in the Services Registry is with lower case of the characters but in theWSDL the endpoint is with upper case. In your case the endpoint url in
the Services Registry is as shown in the exception above:
http://erp.esworkplace.sap.com/sap/bc/srt/xip/sap/ecc_srvcreqcrtrc?sap-client=800
but in the WSDL the endpoint url is with upper case of the endpoint:
../ECC_SRVCREQCRTRC/..
Because of this difference the call fails. This is fixed is 711 SP2.
Workaround for this is if you create a Provider System based on your
WSDL, not a Services Registry one.
Hope that helps...
Best regards
Michael

AMX Configuration for Orable BPM Approval Process

Hi,
Can any one brief idea about the AMX configuration in BPM?
My Requirement is to get Approval hierarchy for BPM task Flow.
Thanks,
Madhava

Hi Suresh,
i just got an answer on my ticket. Here it is:
There is a known issue with the upper case of the endpoint published in
the Services Registry and in the WSDL.
Before SP2 the matching for the binding for invocation is done
by the endpoint url. There is a known issue that the endpoint published
in the Services Registry is with lower case of the characters but in theWSDL the endpoint is with upper case. In your case the endpoint url in
the Services Registry is as shown in the exception above:
http://erp.esworkplace.sap.com/sap/bc/srt/xip/sap/ecc_srvcreqcrtrc?sap-client=800
but in the WSDL the endpoint url is with upper case of the endpoint:
../ECC_SRVCREQCRTRC/..
Because of this difference the call fails. This is fixed is 711 SP2.
Workaround for this is if you create a Provider System based on your
WSDL, not a Services Registry one.
Hope that helps...
Best regards
Michael

Basic configuration for a WLAN Controller - 4400

I've been reading over the "Cisco Wireless LAN Controller Configuration Guide, Release 4.0".
So it looks like once you have the HTTPS enabled and the management IP set, the majority of the configuration is through the GUI - clicking your way through all the settings.
I've never used a wireless LAN controller -- so to make this quick and easy, is it possible to make a "quick and dirty cut and paste" CLI template to get it up and running with just minimal settings left to be done?
If so, could you post it? Thanks.

Well, first you will have to console into the wlc and go through the startup wizard. that is your minimum configuration to get it working. No way around this unless you build a script to automatically enter information on the startup wizard.

Basic configuration for Aironet 1220B

I'm trying to setup my AP so that the ethernet port connects to a hub on my LAN, just like I would connect a PC, printer or server, then us it from a wireless device just like it was on my LAN. I can see the wireless portion of the box from a notebook computer and connect to the SSID fine. I can also ping the ethernet port from a wired computer and can connect to the HTTP port fine. But the notebook can't ping anything on my LAN thru the AP. I thought one of the sample configs would have this, since it's so simple.

12.05 would be the best path for VxWorks upgrade, but you should consider converting the AP to IOS to provide better troubleshooting tools and compatibility. The conversion from VxWorks to IOS is done using a conversion image, which you can load through the browser. The only caveats:
1. You'll want to upgrade the IOS again, after you've completed the conversion. The conversion image loads an old IOS image.
2. You'll want to make sure you disable your radios prior to upgrading.
3. You'll lose your configuration as a result of the conversion (though that can be a good thing). There is a conversion tool that allows you to retain your configuration, but it typically adds a lot of unnecessary junk in the configuration. With a single AP, I'd just do a straight conversion without the tool and then acquaint myself with the IOS GUI by reconfiguring from scratch.
Here are some useful links:
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_release_note09186a00802145c2.html#wp33375
-Location of conversion image and tool.
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_release_note09186a00802145c2.html#wp35396
-Conversion instructions
The above references are in the conversion image release notes. Take a look through the complete release notes for other important notes.
-Ben

Basic configuration for Archivelink on smartforms ?

Hello,
could you provide me a sample guide to configure archivelink ( using sap database table to store data )
to store documents created by smartforms ?
tks a lot,
Roberto.

declare ARCH printer on spad

Basic Template For CSS11501 Configuration

I am trying to get a basic configuration for a CSS. I have attached a visio document to assist I just need to understand the ingress and egress interface configuration/routing.

Thank you Bkennedy for replying,
I changed my template to be as follow:
#MODE_ENABLE
copy running-config ftp:
$Mgmt_IP_addrress
$name
#MODE_END_ENABLE
but still I am receiving Error like :
Error : Exception while sending interactive commands to device, Expect timeout: Failed to match expected device output due to Expect timeout current timeout 60000. Current output : Address or name of remote host []? Current expects : (DC-450.{0,30}|DC-4507-AGG)$[^$]+\)#\s*\z DC-4507-AGG#
I believe that we have to tell the Prime how to send the variables to Switch, because the switch is waiting for the remote host IP address and the destination file name???
DC-4507-AGG#copy running-config ftp:
Address or name of remote host []? X.Y.Z.W
Destination filename [dc-4507-agg-confg]?
% VRF table-id 0 not active
% VRF table-id 0 not active
Writing dc-4507-agg-confg !
24425 bytes copied in 1.500 secs (16283 bytes/sec)
DC-4507-AGG#

Running reports in Portal- URL vs RDF

I've got a content area in portal 3.0.8 which contains two items-- a URL link to my report, and an Application Component which is the same report registered in portal as an RDF. The report runs fine with the URL link, but hangs when I try to run the RDF component.
My URL link is defined as follows: http://greap004:7777/dev60cgi/rwcgi60?server=reportserver+report=reportname.rdf+destype=cache+desformat=htmlcss+userid=username/password@DBname+paramform=yes
However, the registered RDF does not prompt for a DB login or bring up the parameter form. It just hangs for about 5 minutes and then returns the following error:
Error: The requested URL was not found, or cannot be served at this time. Oracle Reports CGI - Report Job was cancelled upon user request.
I want to be able to register reports as RDF's rather than using URL links.

hello,
you should take a look at our whitepapers in the Internet Deployment and Security section of our product area http://otn.oracle.com/products/reports
there you find a walkthrough of the configuration for running registered reports in portal.
regards,
the oracle reports team

Basic setup for cisco 5510

Dear All,
kindly assist with the basic configuration for setting up cisco ASA 5510 for NAT and DMZ.

Below is my config:
ciscoasa> EN
Password:
ciscoasa# SH RUN
: Saved
ASA Version 8.2(5)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 41.206.22.86 MTN-Link
interface Ethernet0/0
description 16mbps link
nameif outside
security-level 0
ip address MTN-Link 255.255.255.252
interface Ethernet0/1
description Inside
nameif inside
security-level 0
ip address 192.168.10.254 255.255.255.0
interface Ethernet0/2
nameif DMZ
security-level 0
ip address 10.10.10.1 255.255.255.
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
clock timezone WAT 1
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
mtu management 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (outside) 1 41.206.22.84 255.255.255.252
nat (inside) 1 192.168.10.0 255.255.255.0
route DMZ 10.10.10.0 255.255.255.0 MTN-Link 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statist
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
<--- More --->

Can Central System administration be configured for JAVA systems?

I know, we can configure Central system administration (DSWP -> Solution -> Operations Setup) for ABAP and ABAP+JAVA systems.
Can some one tell me, can it be configured for JAVA systems like Portal?
Thanks
Aditya

Hello Aditya
Unfortunatelly Java only systems are not supported by CSA in EHP1. The CSA infrastructure is currently being overhauled and as a result of this, pure Java systems will also be covered starting with the next release of SAP Solution MAnager (SAP Solution Manager 7.1) The availability of this next release will be this year, but I am not yet sure when exactly. You can check further info in www.service.sap.com/solutionmanager -> in the last line of this page there is a link to get detail about this version Ramp-Up.

Basic qos for video using mqc

I have two 2800 routers connected via T1. I need a basic configuration for prioritizing my video using MQC and LLQ.
Thanks.

Hi,
you have to build only 2 priorization-queues. One for Voice and one for Video (with lower performance).
The third queue will be a wfq-queue with lfi to be sure that big-packets are not reasons for bad voice or video.
the signalling should be in the voice-queue.
look at
http://cisco.com/en/US/tech/tk652/tk698/technologies_tech_note09186a0080094660.shtml
greetings
Michael

Want to delete all the mails in the mail box configured for BPM Portal

Hi All,
Do you have idea to perform this activity.
I want to delete all the mails in the Dev mail box configured for BPM Portal.
Server and mailbox details as given below :
Mail a/c = Y00123
Mail server = sap.mail.com
Thanks, Sanjay

http://java.sun.com/developer/onlineTraining/JavaMail/contents.html
http://www.jguru.com/faq/view.jsp?EID=17035
if you know the password of the account, i think you can also access the mail using mail client, like you use outlook to deal with your company mail daily.

Basic configuration in GRC 10 for portals

Hi Gurus,
Could you please tell me the basic configuration details in GRC 10 for portals.
Thanks,
Mukesh

Hi Mukesh,
You can refer to https://websmp230.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/sno/ui_entry/entry.htm?param=69765F6D6F64653D3030312669765F7361…
However there is no such guide on Portal integration with GRC, you might need to follow below steps:
1- Create one HTTP type RFC connection between GRC and Portal system.
2- Create System Alias in portal system for GRC system
3- Deploy the GRC Portal content in Portal system
5-Portal content comes with 5 work-sets and one security role.You can assign the portal role that comes with the Portal content to user in Portal and also GRC roles to the same user in GRC system.
Hope this helps.
Regards,
Ameet

Basic configurations for running BPM in portal

Similar Messages

Maybe you are looking for