Basic wireless mobility domains (Control and Data Path Down)
I am unable to get my 4402 and 2504 to pair in mobility, I made short video to explain my issues.
Any help is greatly appreciated, also do not worry there is no propritary information in this video, I am working on a lab that does not mirror any production networks.
http://www.youtube.com/watch?v=7nVG1h12Y34
4402 Mobility IP = 10.60.1.9
2504 Mobility IP = 10.40.1.4
From the 4402 I get this output:
(Cisco Controller) >mping 10.40.1.4
Send count=3, Receive count=0 from 10.40.1.4
(Cisco Controller) >eping 10.40.1.4
Send count=3, Receive count=0 from 10.40.1.4
(Cisco Controller) >ping 10.40.1.4
Send count=3, Receive count=3 from 10.40.1.4
From the 2504 I get this output:
(Cisco Controller) >mping 10.60.1.9
Verify IP address belongs to a mobility peer
(Cisco Controller) >eping 10.60.1.9
Verify IP address belongs to a mobility peer
(Cisco Controller) >ping 10.60.1.9
Send count=3, Receive count=3 from 10.60.1.9
Similar Messages
-
WLC 7.4.100.0 Mobility group control and data path down
Hi All,
Today i am facing issue with mobility group. i checked and found control and data path is down on foreign controller.I am able to ping anchor controller. Required ports are open on firewall but mping and eping fails. Any idea whats wrong. On Anchor controller, i have 7 foreign controller configured and among these 3 are working fine. Having problem with 4 foreign controller. Previously all are working fine and there is no changes made on network or firewall.Post output of "show mobility summary" of your Anchor WLC & a non-working WLC. Also "show sysinfo" of those two controllers.
Regards
Rasika -
Can I download the instrument Control and Data Aquisition Device Driver CD for 7.1?
Greetings,
Can I download the instrument Control and Data Aquisition Device Driver CD for 7.1?
I'm trying to find out if I can download
the instrument Control and Data Aquisition Device Driver CD for 7.1. Instead of downloading all the upgrades?
Is there a link to the image file for this CD?
TIASam,
Unfortunately, the Device Driver CD is not available for download. However, your Technical Sales Representative should be able to send it to you (Contact Information).
Spencer S. -
Standard application configuration and data paths on Linux
Hi,
I have some problem with choosing proper place for application global configuration and data paths on Linux.
I saw following paths for application configuration:
/etc/app_name
/etc/xdg/app_name
/usr/share/app_name
/usr/local/share/app_name
/opt/app_name
and following for application data:
/usr/share/app_name
/usr/local/share/app_name
/opt/app_name
Which directories are standard and distribution independent?
best regards,
Lukasz
Last edited by lgro (2012-02-16 20:46:23)Wouldn't environment variables like XDG_DATA_HOME, XDG_CONFIG_DIRS, XDG_CONFIG_HOME, etc be best?
Many languages' standard libraries have functions for accessing these effeciently in a distro-agnostic manner. -
Tutorials for MVC, Data Controls, and Data Bindings
I am looking for some good tutorials on:
Model View Controller concept
Creating Data Controls from Java Beans
Creating and Using Data Bindings
We are using JDeveloper, but do not want to use ADF as we want more control than ADF offers.
Thanx
PamJust curious, what control do you need that ADF doesn't offer you?
If you use ADF, you don't have to use it for every page. You can bind some components on your page using adf directly to your adf data controls, and you can bind other components to your backing beans, and have full control. No reason to throw out adf if there are just a few cases where you need more control.
Btw, do you have a link to a page describing these non adf data controls and data bindings? -
Creating controls and data triggers statically
Hi,
I have two questions wrt WPF:
1. I've set of controls like below:
<Grid >
<Border x:Name="DrawerOneBorder" Height="212" Width="227" Margin="1" BorderThickness="1"
BorderBrush="{StaticResource TileBorderBrush}" >
<TextBlock Style="{StaticResource TileTitleTextStyle}">Drawer1</TextBlock>
</Border>
<Image x:Name="DrawerOneImage" Height="50" Width="50" HorizontalAlignment="Center" VerticalAlignment="Center"
Source="..\Status\CheckMark.png" >
</Image>
<TextBlock x:Name="DrawerOneWarningText" Text="Drawer is open" HorizontalAlignment="Left" VerticalAlignment="Bottom"
Margin="15" FontSize="16" ></TextBlock>
<TextBlock x:Name="DrawerOneErrorText" Text="Error" HorizontalAlignment="Left" VerticalAlignment="Bottom"
Margin="15" FontSize="16" ></TextBlock>
</Grid>
The same set of controls I need to create multiple times. Is there a way where I can create a template kind and use it wherever required? (I should be able to change/give some information like text for each of the controls)
2. I've following code for data triggers:
<DataTrigger Binding="{Binding Path=ModuleDetails.Drawers[0].DrawerStatus }" Value="Ok">
<Setter TargetName="DrawerOneBorder" Property="Background" Value="#BDC2FF"/>
<Setter TargetName="DrawerOneImage" Property="Visibility" Value="Visible"/>
<Setter TargetName="DrawerOneWarningText" Property="Visibility" Value="Hidden"/>
<Setter TargetName="DrawerOneErrorText" Property="Visibility" Value="Hidden"/>
</DataTrigger>
Here, only drawer index changes and rest remains same. Is it possible to give common things in static resource and specific thing in each place?
Kindly waiting for your response.
Thanks,
SantoshPlease only ask ONE question per thread.
>>Is there a way where I can create a template kind and use it wherever required?
You can define an element as a resource at any level (application, window, user control etc.) and then reference it using a ContentControl like this:
<Window.Resources>
<SolidColorBrush x:Key="TileBorderBrush">Green</SolidColorBrush>
<Border x:Key="DrawerOneBorder" x:Shared="false" Height="212" Width="227" Margin="1" BorderThickness="1"
BorderBrush="{StaticResource TileBorderBrush}" >
<TextBlock>Drawer1</TextBlock>
</Border>
</Window.Resources>
<ContentControl Content="{StaticResource DrawerOneBorder}"/>
<ContentControl Content="{StaticResource DrawerOneBorder}"/>
<ContentControl Content="{StaticResource DrawerOneBorder}"/>
Remember to set the x:Shared attribute of the resource to false for a new instance of it to get created for each request to it. Note that you cannot modify any properties of the resource directly in XAML this way though.
If you require to be able to this you should use style resources:
<Window.Resources>
<SolidColorBrush x:Key="TileBorderBrush">Green</SolidColorBrush>
<Style TargetType="Border" x:Key="DrawerOneBorder">
<Setter Property="Height" Value="212"/>
<Setter Property="Width" Value="227"/>
<!-- rest of the properties... -->
</Style>
</Window.Resources>
<!-- override Height of style -->
<Border Style="{StaticResource DrawerOneBorder}" Height="400">
<TextBlock Style="{StaticResource SomeTextBlockStyle}">....</TextBlock>
</Border>
<Border Style="{StaticResource DrawerOneBorder}" />
>>Is it possible to give common things in static resource and specific thing in each place?
I am afraid I don't know if I understand this question but you cannot define the setters in one place and then somehow "import" these setters into the DataTrigger. This is not possible. But please start a new thread if you have a
new question.
Please also remember to mark helpful posts as answer to close your threads. -
The first, most important question of this thread is if I can form a wireless domain or if I have to do it wired.
If it matters, I have a Linksys E1200 router that does wireless and wired.
My second question refers to Group Policy. Is this the way domains limit their user account's capabilities? Because I was planning on making a domain, so that I could have unified user accounts that I could control from the server, limiting what those accounts
can access for further security. Is this what Group Policy does, and how would I move with starting that?Hi Adrian,
>>The first, most important question of this thread is if I can form a wireless domain or if I have to do it wired.
Just as Alan suggested, Active Directory domains support both wired and wireless connections.
>>My second question refers to Group Policy. Is this the way domains limit their user account's capabilities?
Group Policy is an infrastructure that allows you to implement specific configurations for users and computers. Group Policy settings are contained in Group Policy objects
(GPOs), which are linked to the following Active Directory directory service containers: sites, domains, or organizational units (OUs). The settings within GPOs are then evaluated by the affected targets, using the hierarchical nature of Active Directory.
Consequently, Group Policy is one of the top reasons to deploy Active Directory because it allows you to manage user and computer objects.
Regarding group policy, the following link and articles can be referred to for more information.
Group Policy for Beginners
http://technet.microsoft.com/en-us/library/hh147307(v=WS.10).aspx
Group Policy Planning and Deployment Guide
http://technet.microsoft.com/en-us/library/cc754948(v=WS.10).aspx
Group Policy
http://technet.microsoft.com/en-us/windowsserver/bb310732.aspx
Best regards,
Frank Shen -
Stepper Motor with Linear Stage (Position Control and Data Acquisition)
Hey All,
So.. I've attached a stepper motor to a linear stage and so far it's working pretty well. Using a stepper motor driver from Pololu, I've simplified the control of the motor by just using output pulses from the counter output of a PXI-6143. I've tested the motor using the Pulse Train examples in LabVIEW and all is working well.
My goal now is to allow the user to collect data from a pressure sensor, attached to the linear stage, every X number of steps. From what I can tell so far, and please correct me if I'm wrong, the motor step movement is synchronised with the pulse train input. That is to say, if I give the motor a 200 step pulse train, the pulse train ouput is completed at the exact time the motor has moved 200 steps. From this, I've created a VI that moves the motor X steps, aquires the data point, and then repeats this process for the required amount of data points. The problem with this is that the motor movement is not continuous; it stops for a split second to take the data point.
How can I have labview ouput a pulse train of say 1000 steps and record a data point every 50 steps?
Two ideas that came to mind were:
1. Use the counter input port on the card to count the pulses being sent to the motor.
2. Use an encoder connected to the motor shaft.
I wanted to stay away from theses ideas though since they require resources from the DAQ card.
Thanks,
RyanHi Ryan,
Just to cover all the bases, what version of LabVIEW are you using and can you attach your VI? Initially your ideas sound like they should work, do you expect to be nearly maxing out the DAQ?
Thank you,
Deborah Y.
LabVIEW Real-Time Product Marketing Manager
Certified LabVIEW Architect
National Instruments -
Labview remote control and data transcation
Hi,
We have a complicated timing control system written in labview
6.1 running on our lab PC-1. Since it is not easy to upgrade to a most
recent version and limited PCI-slots, and we need to add a few device
control programs (written in C++ or updated labview), we are thinking of
an ultimate control system with two PCs and let the old timing program
be a "slave" of "master" computer PC-2. OS for both PCs are windows XP.
The communication between the two PCs are
fairly straight forward: suppose on PC-1, the program breaks into two
parts: part A and part B. PC-2 sends selection messages to PC-1 to
determine which part needs to be running during a particular shot. It is
true that to our best interest we might need PC-2 to send data to
PC-1, in case for a particular run we have to change some data values of
timing program.
The problem might appears to be a piece
of cake to you experts. It is worth mentioning that on PC-1, any
changes made to the timing program is nontrivial due to its structual
complexity. The program is DAQ based (finite) pattern generation (using a
lot of PCI 6534/PCI 6713/counters, external clocking).
The
reqiurement for speed is not high. PC-2 can in general wait for 1
second before PC-1 receives a message and start to output. On the
other hand, the smaller the delay, the better.
We have
considered a few communication options like TCP/IP, RS232 ports, etc.
But before we start implementing the changes, we would really appreciate
your suggestions/comments!
Thanks very much in advance
for your time!
KunyanKunyan,
there are really several different ways to solve this. The major question is: Is this a handshake protocol or simple "notifications"?
If it's simple notifications, things are getting quite easy.
You can use TCP/UDP/DataSocket/STM if there is a network connection between both PCs. Otherwise, RS232 might be a good idea as well for sure.... but i suggest a network technology in order to reduce delays.
STM is a protocol built up on TCP and even if you do not use it (it is not available for LV 6.1!), it might get you some ideas about defining a custom protocol.
hope this helps,
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it. -
SSIS Control and Data Flow Items not available in Customize Toolbox
I cannot add additional Data Flow and Control Flow items to the SSIS Toolbox. I am using SQL Server 2014 and VS 2013 (BIDS). The standard SSIS items appear - but they are all of them. How do I add the additional ones that are not loaded by default. I didn't
have this issue with SQL Server 2012.
Thank you,
Johhn
JohnJohn, which ones you do not see? AFAIK nothing has changed regarding how the items get added to SSIS toolbox in SSDT or VS 2013 with SSDT installed (no BIDS in SSIS 2012 and up).
Arthur My Blog -
Grid Control and Data Guard Setup
Hi,
I have 4 PCs on which I wish to test the following:
1. OEM Grid Control 10.2 - Console + Service + Agent
2. Data Guard feature with Broker
3. Standby Setup for a Primary Database.
I will create the Primary DB on one Linux PC.
Standby DB using Grid Control & DataGuard on second Linux PC.
The Third PC is also Linux but the fourth PC is Windows XP.
Please guide me in understanding the following:
1. On which PCs should I install OEM Grid Control 10.2 - Console + Service + Agent?
2. On which PC should I setup DB Broker?
Please assume that I will use Oracle 10.2 Softwares and Linux x86 version.
Regardswell why don't you go ahead and test?!
Test and see whether you want to put oms, console all one machine, or whether you want to separate out the componests (you'll need an agent on each box regardless). I have no idea what the specs of your machines are, so why don't read the documentation on Grid and dataguard, see what the recommended settings are and then plan what you want to do.
Bazza -
RTSI motion control and data acquistion
The code attached is part of an example that uses every falling edge of an encoder pulse via a 7334 motion controller card to clock data on a PCI6023E card. (Position-based DAQ)
Is there a way using this code (or otherwise) so that I could use this signal or some other signal to only TRIGGER the daq on the 6023E? (I want time-based daq)
Thanks for your time and patience
Chris
Attachments:
example.vi 99 KBYou can definitely use a pulse to trigger an analog acquisition on the 6023E device. I would suggest to look at a LabVIEW shipping example that illustrates how to integrate a digital start trigger for analog aquisition.
The 'Acquire N Scans Digital Trig VI' would be a great place to start. You will just need to add a control/constant to the analog chan & level input of the AI Start VI and enter "RTSI0" into the string of that cluster input. This will set the 6023E to trigger off of RTSI0. So, instead of using the RTSI line in your program for the analog scan clock, you will use the RTSI line as a digital start trigger.
I hope this helps.
Regards,
Todd D.
NI Applications Engineer -
Remote control and data logging
Hello,
Somebody can help me?
Measuring computer measures data from data acquisition card continuously. Measured data are saved to .txt file and moreover they are transmitting to Data server over Ethernet. Remote computers should be able to access to this server (Duplex) data though LAN during measurement.
for details see attached file
Attachments:
description1.doc 36 KBStefo wrote:
Don't understand me wrong please! I don't looking for already developed software. I need some footing for beginning. I’m thinking that I find it in manual just now. Again But what I'm looking is maybe some advice, or simple example. I want to improve my self, no take already developed solution.
best regards,
I didn't want to cause offence to you
Maybe it's just me, but what you asking for in this post is something that I would not do for free unless I was being paid as a consultant. You already have the simple outline of what is required.
This is an engineering project. The solution it isn't something that you can find in a manual. If only things were that simple. -
hello
i have an oracle database 10GR2 EE on windows server 2003 sp2
the database is in archive log mode
today i lost all control files+ the system datafile
i have a cold backup + a script to recreate the controlfiles
i restored the system datafile from cold backup
but when i run the script to recreate the controlfiles i got this error:
ERROR at line 1:
ORA-01503: CREATE CONTROLFILE failed
ORA-01189: file is from a different RESETLOGS than previous files
any help is appreciated
thanksHi,
Please refer to Metalink Note:121801.1, there is an step by step resolution.
Regards,
Adrian -
Best way to control and read data from multiple instruments?
Hello,
I'm building an application to test power supplies involving multiple pieces of equipment over a couple of different comm busses. The application will also send control instructions to some of the instruments, and read data from some of the instruments. The reading and control profiles will not run on the same schedule (variable length control steps, configurable read interval).
I was thinking of using a queued statemachine (producer/consumer) for the control profile and another to read the data, but I got concerned that there would be collisions between sending control commands and read commands to the same machine. Is there a suggested design pattern for implementing something like this?
Timing of the commands isn't critical down to the milisecond, but I need to collect reasonably accurate timestamps when the data is read. The same is true for the control commands.
Here are the instruments I'm going to use, if the are control, read, or both, and the communication method
Instrument Funtions Comm Method
Power Supply Read data Communicates to PMBus Adapter
PMBus to USB Adapter Read data USB (Non-Visa)
Switch control relays USB (VISA)
Power Dist. Unit read data/control outlets SNMP (Ethernet)
Electronic Load read data/control load GPIB (VISA)
Thermal Chamber read data/control temp Ethernet (VISA)
Thanks,
SimonHello, there is a template in LV called "Continuous measurement and Logging".
It can give you some idea how to properly decouple the "GUI Event handler" top loop (where your Event structure is) from the DAQ and other loops.
You do not need to totally replicate the above example, but you can find there nice tricks which can help you at certain points.
The second loop from the top is the "UI message loop". It handles the commands coming from the top loop, and regarding to the local state machine and other possible conditions and states, it can command the other loops below.
During normal run, the different instrument loops just do the data reading, but if you send a control command from the top loop to a certain instrument loop (use a separate Queue for every instrument loops), that loop will Dequeue the control command, execute it, and goes back to data reading mode (in data reading mode the loop Dequeu itself with a "data read" command automatically). In this way the control and data read modes happen in serial not in parallel which you want to avoid (but I think some instrument drivers can even handle parallel access, it will not happen in really parallel...).
In every instrument loop when you read a value, attach a TimeStamp to it, and send this timestamp/value couple to the DataLogging loop via a Queue. You can use a cluster including 3 items: Source(instrument)/timestamp/value. All the instrument loops can use the same "Data logging" Queue. In the Datalogging while loop, after Dequeue-ing, you can Unbundle the cluster and save the timestamp and data-value into the required channel (different channel for every instrument) of a TDMS file.
(Important: NEVER use 2 Event structures in the same top level "main" VI!)
Maybe you are looking for
-
Message bar expanded by default
Dear All: We wish to change the message bar to expanded by default, instead of collapsed by default. I've been searching how to do it, but I could not find any information about it. How can we personalize the webclient so that the message bar is show
-
after the newest update every time i put something into the trash it deletes instead of going into the trash folder, and it always asks me when i move something into the trash if i want to because it will be deleted immediately. before i could put st
-
I´ve bought Iwork suite for my mac book pro in a retail store, 2/3 years ago, can I made any upgrade version through Itunes without paying any additional fee? Someone could assit me on this particular issue? regards Bernardo
-
Can't burn any DVDs on external firewire drive
Since I installed OS 10.4.9, neither DVDSP or toast titanium will recognize a "stable connection" to my external firewire lacie recorder... the message I get from toast is: 1. Interface Error: -50 The connection is not stable 2. The drive reported an
-
How to Extract data and reports from the SAP BW warehouse
Hi to All Guru's I am new to SAP BW. Can any one help me to know, How to Extract data and reports from SAP BW. Do we use any tools. After Extracting the data from SAP BW how can we move all the data to Cognos. It would be kind enough to provide me