Batch capture produces VTR error?

I am trying to batch capture from Digibeta. I have 14 reels with three 25 minute clips per reel and every time it gets to that third clip, it stops and gives a VTR error saying that it appears I have reached the end of the tape.
The tape is still playing - I can see it on the secondary SDI output to a pro monitor. I have captured these clips before without problem, there is no break in T/C and oddly enough, when I try to capture that clip again it works just fine?
Any ideas what mayu be causing this?

No TC break per say but is it possible that the code is rolling over somewhere early in that last take?
rh

Similar Messages

"No Video" error when Batch Capturing

I am getting a new error that I have not seen before when using Batch Capture in FCP. It cues the tape, starts the pre-roll and then spits out an error message that there is "no video". Of course, there is video.
The same thing does not happen when capturing one clip at a time nor does it happen if you capture live (hitting Capture "Now" in L&C window).
Any thoughts?

I also don't want to keep paying $23 a month for software that is not 100%.
Software as complex as Premiere Pro will never be 100% bug free.
I'm also inclined to believe this is more of a system issue than a PP issue. I don't recall other reports of this nature, and it works fine on my own system.
The only other thing I can think of to suggest is another FireWire port, possibly by adding a FireWire card to the system. I've read that the chip makes a difference, so research over in the Hardware forum.

Batch Capture Error: Timecode Error: End of Tape Reached

I have been having issues doing batch capture with my JVC VS30U. I logged all my clips on the fly and did the entire tape, so the OUT point of one clip is the same as the IN point of the next clip. When I attempt to batch capture it gives this error between every clip.
I have to hit retry, sometimes more than once, in order for the deck to properly cue and FCP to start the digitize. I don't know if this is a weird pre-roll issue, or something else, but it completely defeats the purpose of a batch if I have to sit here and hit retry after each clip.
There are no TC breaks, and obviously its not really the end of the tape. I've read where people have similar problems, but didn't find a solution. Have already trashed prefs, but to no avail. Using FCP 5.0.4 with OS 10.4.3 and said JVC deck via firewire.
Any ideas? Thanks in advance!

I don't know the deck but a simple test would be to move a couple of i/o points so they are not adjacent. Or test with a single, longer clip and break it up into subclips.
Tell us what you've tried so we don't waster your time and ours with fruitless suggestions.
Errors displayed by FCP are usually irrelevant and rarely helpful.
bogiesan

Timecode error in batch capture

I've searched this problem but still haven't found an answer. When I batch capture, I get a "Timecode error" and on about half the clips I logged I have to cancel out of the capture. some work,some don't. It's not a problem with the pre-roll at the beginning of the tape; I left plenty of room when I set the in/out, and the first clip is now captured anyway so it can't be the start of the tape. But every time I try to capture the rest of the clips, I get this error with some if not most of them. I've changed the setting to NDF and it doesn't seem to make a difference. I'm only capturing in the middle of the tape now, so the beginning and end have lots of space. Please someone tell me how to stop this! I just upgraded to Pro and it's my first attempt at batch capture, so I'm pretty disappointed that it's such a waste of time.
Thanks, smart people!

Great, now you made Studio go and have some fun on the weekend.
X is right eliminate things one at a time.
You didn't let us know what drive you are capturing to.
If capturing from the camera doesn't work, it may be that you are experiencing the "multiple FW devices on one FW bus issue" in which case you might try looping the camera or deck through the drive, works for some, but more likely you will need to install another FW bus via the card slot on the laptop.
By the way, this really doesn't sound like a drop/non drop issue, but look at the timecode display of the footage on tape. If the last 2 numbers are preceded by a semicolon,,, it's drop frame.
Now, I believe someone mentioned the US Open!
rh

Batch Capture - Error/Warning

I have a PowerPC G5 with a Firewire800 external HD plus a SATA external RAID system all connected to the G5. I have been (up to now) successful in batch capturing my video's. I now get an error message (warning) when I attempt to batch capture even one file. The messages says:
Warning:
_You are about to capture non-drop frame media from a device currently detecting or configured for drop frame media. If you proceed, you may experience changes in logged in and out points, problems relinking media or removal of master clip relationships_.
If I continue, the process quickly gives me an error.
My playback unit is a Sony DSR-11. I am capturing it directly to the 800 Firewire external HD (granite digital). I have ran TechTool on the G5 without issues (I even re-seated all the PCI cards, memory boards prior to running TechTool). I have two aftermarket cards (SATA card for the LaCie and a Firewire card). The Granite Digital is plugged into the standard 800 Firewire port.
The only way I can capture a video is by NOT using Batch Capture but only by capturing the individual clip. For some reason that works but the Batch Capture does not. I use this system a LOT for video editing (I use FCP Pro 6.0.5).
I would appreciate any suggestions.

I didn't receive a reply to this but I believe I figured out what what "drop frame box" Irl is taking about.
The only Drop frame box I could think of is in User Preferences. I unchecked that and it didn't do anything. I captured one clip and the audio was out of sync.
Looking at the Batch Capture dialog closer I noticed an unchecked "Add Handles" with a timecode that includes the semicolon. I checked that and started the recapture. The Warning came up again but I went ahead and the audio was back in sync.
I have no clue as to why this setting is in the batch window as I only thought handles were for trimming. The manual skips over what it does. I'll reply again if I find anything else.
Dan

Batch Capture : Timecode Error?

So I am attempting to capture my first video onto FCP from my Canon XL. I have about 5 minutes of video and I have logged the info for each clip. They are all in my "Bin 1" and it is set as a "logging bin." The first logged clip that i want it to capture i have marked the "In Point" at 00:00:00;00 and the "Out Point" at around 00:01:09;24. The rest of my 11 clips just go in order (i.e. 2nd clip: In = 00:01:09;25 etc...). After doing all of this I click on "Batch" under the "Capture" option, a big black screen pops up over my FCP with the capture info underneath the black screen in a gray strip. My camera then rewinds to the beginning and STOPS. I then have to sit and wait for anythin to happen, my camera still saying "STOP," and then a message pops up reading the following:
Batch Capture: Timecode Error: Unable to locate the specified timecode. You may have specified a timecode with insufficient room for a pre/post roll operation.
I have no idea what this means and I am beginning to get impatient with capturing my video. In the Log and Capture window, the tab that says Logging, i did not mess with the "Markers." I don't know if this matters.
Any help would be GREATLY appreciated so that I can start editing my project with this wonderful software otherwise.
God bless,
|-(|:^D
`

In standard trim, FCP needs at least 5 seconds preroll before capturing. The preroll is so the tape can get up to speed, the heads read timecode accurately and so on. You have discovered what happens when you give it no oppertunity to sort itself out.
The simple answer for your current situation is to set your first in point 10 seconds after the start of the time code. Be sure to make sure your last clip's OUT point is 10 seconds or more before the end of time code or you can have problems at that end of the capture as well.
The long term answer is next time let the camera run for a minute or two before you start recording anything you will want to keep. The same is true for the end of the tape - let it run for another half minute or so.
Cheers,
x

Batch Capture won't launch/gives no error message

that says it all.. Worked fine yesterday.. Log and Capture loads fine.. vtr shows ok.. I select files to batch capture and nothing happens not even a message..
anybody offer hints to make this work? Thanks
btw.. searched for this exact problem in search forum and didn't find this one in there. thanks again
Josh

Glad you found the answer, I was wondering what the problem was when I read the post. Sometimes you can learn the most about an application by troubleshooting.
Can you mark this thread as being solved so it can help future people searching the same issue?

Error while Batch Capturing on to Final Cut Pro

Hello,
When you batch capture from any deck randomlly it gives an error "do not attempt to eject the tape" and the capture stops and after that it gives this error serveral time again and again but the same tape works fine with other machine.
Try to help me out as soon as possible.
Thanks

Sounds like you need to repair the video playback machine which is sending the error messages...
Jerry

Errors Batch Captures!! Tips for setting up Batch list corre

I have set up a Batch List, and I keep getting an error after I have imported the Batch capture list, when I go to Batch Capture I keep getting an error about Timecode? I am also wondering when doing a Batch List is ok to begin with 00:00:00:00 timcode as a media begin? As batch capture truly saves a lot time, I sincerely appreciate your time in courtesy in replying to my post.
Sebastian

I avoid this problem by shooting the first 30 seconds of each tape to throw away. That way, my starting code for any new tape is always at least 00:00:30;00. I started doing this back with FCP 3 (and now have FCP 5). So, I don't know if this is still an issue with the newer version. I do know, however, that working with timecodes below 30 seconds was a pain. Before I learned this trick, I would be able batch capture all of my other clips. Then, the first clip on each tape I would use Capture Now (which seemed to be less finicky with the low time codes).
I hope this helps.

FCP "general error" on hdv batch capture

help!
i am trying to batch capture around 3k clips that went down when we installed a bad raid controller card that scrambled our RAID, and also 28 hrs of HD footie. OUCH!
anyways i'm trying to batch capture as much as i can to retieve our logging notes and rebuild some of our assemblies, but FCP keeps kickin me hard. after a reasonable amount of success, FCP generates a GENERAL ERROR message, leaving me unable to capture anymore (every time i hit batch capture i get the general error)...
I hate HDV n all, but i think this one is coming from FCP as after i re-install (3 hrs later), i can start crankin out the tapes again....
any ideas how i can avoid this boys n girls? its really killing me and making our sundance deadline of sept 18 a bit of a dream.
peas
andrew stromotich
www.dropframestudios.com

reinstalling FCP rarely fixes anything. If you want to be sure you have a good installation, you need to do an erase and reinstall of the system drive. This gets you a clean version of OSX, FCP and QT. If that doesn't work, you likely have a hardware issue.
Good luck,
x

Batch capture a sequence - strange error

Hi I am trying to batch capture a sequence (1 hour long, captured on DV PAL), now I am trying to get it into the FCP in HDV. I copy the sequence make all clips offline, select batch capture and it asks for a tape. So far so good.
Always when I put a tape it will rewind the tape fully and then give a time code error...
Is the first time I do a batch in FCP. I think I select the correct audio/video setup, but always happens the same: rewind and error...
Can anyone help me?
Am I missing something?

FCP rewinds the tape because it loads the clips in ascending timecode order -not the order that they appear in your sequence. This saves wear and tear on the tape because FCP does not have to spool back and forth, it simply progesses up the tape grabbing the clips.
It might be that the first segment that FCP is trying to grab is too close to the beginning of your tape and there is not enough stable timecode at that point.
Try the following: reduce the amount of pre-roll time or shorten the length of any handles you may have assigned.
It is probably a good idea to reduce pre-roll time and/or handles just for this first clip, then do the rest with your normal settings.

Batch capture HDV error

I have FCP 5.14 and have just logged a bunch of HDV footage offline. I did this the normal way I would when capturing DV footage, marking the in and out point and then log the clip, standard stuff?
When I try to Batch capture the offline clips it captures only 1 frame from each clip, then the clip details are also effected, ie the Media start and media end of my clips changes from what they where into two new time codes 1 frame either side of the newly captured clip.
Is this a program error or am I just completely useless??? Can somebody help me please

Not sure if this is your exact problem, but I've had issues with Batch Capturing HDV in FCP 5.1.4 using both a Sony M15U and M25U.
The deck would seek to the appropriate place on the tape and then just jog back and forth looking for the right start point. It would do this about 3 times and then give up.
The solution for this was a DROP FRAME / NON-DROP FRAME setting in FCP. If you go to your A/V Settings and then to the Device Control Presets tab and edit your preset (If it's locked you can just make a copy of it and edit the copy - I am using the Sony HDV firewire preset). If you know what your footage was shot in (drop or non) make this setting adjustment. If you don't know, try both.
As soon as this not so little detail was checked everything batch captured without fail. Just make sure there aren't any timecode breaks on your tape.
Hope this helps.

Batch capture error DF or NDF

Hi
I tried to batch capture a sequence but the FCP gived me the message of error in capture because the tape is NDF and the sequences is DF. I think I logged right the material (DV, and Betacam SP -via a Keyspan-).
I haven´t changed any setting in the the hardware a DSR11.
Any ideas of what's happening?
G5 dual core Mac OS X (10.4.4)

I seem to remember this happening to me, but for the life of me, I can't remember how I solved the problem.
Make sure you've let the tape run for a second or two so that it correctly recognizes the fcm (frame code mode) of the tape. If that doesn't solve the problem, you may be out of luck. You could export an edl change the fcm of the source clips in a text edit program and recapture. You might have to adjust the occasional edit, but it would probably save alot of time.

Recommendation for HDV vtr or camcorder for batch capture

I currently own Premiere Pro CS3 and am using the trial version for PP CS4 on a Mac. One of my biggest problems is batch capturing HDV footage with my Sony HVR-Z7U HDV Camcorder or HVR-M15AU HDV Deck. It just doesn't work properly for CS3 and was disappointed to find out it doesn't work for CS4 either (unless it's a trial version issue?). Both versions I can capture on the fly, but not a batch capture. Even the adobe website say's so. So my question is, what reasonably priced HDV camcorder or VTR can I get that is compatible (let me batch capture) with both versions? Does anybody know? Thank you.

The problem I've found when capturing from the M15 is that the deck does FF and REW at such high speed that it frequently overshoots the mark by as much as two minutes, and then ends up capturing about one minute off. I usually only discover this when I look at the captured clip and find it isn't at all what I said it was when I named it.
So I just take the clip offline and recapture. This usually works. Sometimes I will manually cue the deck up to about one minute before the "in" point, and this helps the deck/Premiere find the correct timecode.
Anyhow, that's my workaround. I have handles set at 150 frames and pre- and post-roll set to the same.
(But note this is for CS3, although I assume this part is the same with CS4.)

Batch Capture Error

I just logged about twenty clips and attempted to batch capture them but nothing happens. I hear an audio pop but the batch capture window does not open. I have tried trashing the prefs within the FCP user data folder, but no change. This is a new problem. I have successfully captured in the past. I'm using a JVC SR-VS30 DV deck. Any ideas would be appreciated. Thanks.

Since we're not watching over your shoulder, we've got to insist you check the easy things firts. Are you sure you have logged clips that are longer than a single frame? It's easy to do.
try batching only one clip.
bogiesan

Batch capture produces VTR error?

Similar Messages

Maybe you are looking for