Batch processing Impulse Responses

Well guys and gals,
the title says it all!
I have plenty of impulse responses and would like to import them into Space Designer... but not one by one. Is there any way to batch-process them to make my life a bit easier?
Maybe a command line?
Thanks!
VN

Hi
http://www.3raudio.com/spacedesignermanager.html
CCT

Similar Messages

Impulse Response editing - Do it the right way: IRs for Space Designer

Dear fellow board members,
after doing several research on this topic and many attempts to match some Impulse Responses I finally have to admit, that a little help or insight would be much appreciated. Most of the (Beamsonic) IRs, especially the Studer and Ampeg IRs, seem to have overlength (≈ 6 sec.) and some do have "silence" at the very beginning (see picture below).
I would be thankful for a helping hand explaining me, which part of this IR is of relevant importance: Do I need the "silence" tail at the end? What should I take care of when editing such IRs as the pictured one? Would only the marked yellow area be of importance? Get rid of the red areas (beginning & end)?
As many of the IRs I do have correspond to the image above, I have to go through heavy manual editing and before doing so, your help would be much appreciated.
Does anybody have gone through this before and would like to exchange some of his material for the Space Designer (IRs + corresponding Presets)? I am looking for: EMT 250, Studer A80 Tape, other Tape Sats as well, Ampeg, Westlake Studio D, other useful top quality IRs as well.
For now, many thanks in advance for sharing interest
Vic.
Mac OS X (10.3.8)

1. You maybe want to comment on what is considered to be the
"technical right way" to achieve DAW Tape Saturation via IRs, i.e.
what makes sense and what not?
Really, there is no technical right way - all we are doing is altering our recorded audio in a way that we like - it will vary depending on your tools, your tastes, the material, the artistic intent etc...
a - Insert the Convolution Reverb right on the Audio Channel
itself with Pre/Post-Compression/EQing, etc.
I will do this if I want to process an individual channel for colour. Remember to set the effect to 100% wet.
b - Send audio to a Convolution Reverb Bus (and share w/multiple
audio channels), loss of quality, etc?
You're just sending a bunch of channels - in convolution terms, the results as far as I know will be the same if you process 10 channels indivdually and sum them, compared to if you sum the 10 channels then convolute them. Remember, convolution is a static process in most tools, including Space Designer.
How would you judge the value of using "Impulse Responses"
in comparison to "Plug-Ins"?
Well, I don't think anyone's done a tape saturation plugin properly yet. I'm not an expert in this field, but had some interesting discussions with one of the Sonalksis developers over on KVR who is heavily researching into tape saturation (he's doing a doctorate in the subject) and he thinks that it is possible to do a decent tape saturation plugin - not easy by a long stretch, but possible, so I'm sure we will eventually see decent plugs appearing.
Having said that, I'm not actually a huge fan of the tape sound anyway - I like the impulses for that colour if I need it, but I certainly don't run everything through it. I don't really like the smeared transients, at least on my "less natural" pieces. Rock music (as an example) may well work better.
The plugins that do saturation in varying amounts are a mixed bag in my opinion. A lot of people love VintageWarmer, but I'm not that keen on it (again, I'm not an "expert" by a long stretch, these are just my personal opinions).
I've had some great results using Guitar Amp Pro for saturation and warming (we're talking subtle stuff here) on drums and guitars.
There are a bunch of other plugs too, but none that I have used to tape saturation. DUY's tape does saturation, but not really accurate tape simulation *from what I have heard* - I haven't used it personally myself. Charles Dye seems to like it, anyway!
. Finally: Did anybody experiance differences in quality when
comparing Convolution Reverbs (i.e. SD vs Altiverb vs Waves) in
processing the same IR?
In general, no. Mathmatical convolution is afaiu a mathmatically "perfect" process, much like the adding of audio signals in the digital realm. As long as you know how to do the maths correctly, there should be no difference, given the same IR (it's the IR that really determines the quality of the output).
Of course, different plugs implement things differently, and have different features, but by and large, the convolution engines these things use should be generally the same.
Again, I'm no expert and haven't done exhaustive testing or anything - this info comes from discussions I have and my understanding of these processes from a DSP point of view. Other may well be able to back up or debunk what I've said, so I'll leave the floor to them now...

Weblogic workshop batch process

hi all,
am new to weblogic workshop. am looking to see how we can start a batch process in wlw (weblogic workshop) that in turn does a few activities like checking for file exsistence from previous application and if not copying it over from the backup directory on the server.
hope to get a response soon.
cheers

And you're asking about BEA's products at Sun's forum why exactly?

Camera Raw adjustments not applying to batch process

Hey friends,
On a 2008 iMac running 10.5.7, latest version of Camera Raw & Bridge/Photoshop, I opened 650 Canon 5D raw files in Camera Raw, made adjustments to most of those files, then clicked Done.
In Bridge Im batch processing all the files to Jpeg, now in Bridges thumbnails I can see all the adjustments I did in Camera Raw were applied, but yet when I batch process them, no adjustments are being applied, any idea what the issue could be?

Thomas Knoll
1. Jul 28, 2007 5:51 PM in response to: (bp)
Re: Warning serious issue with ACR edits not updating
How did you record the Photoshop batch action? Make sure the "Image Setting" item is checked in the setting flyout menu when recording any actions that open raw image if you want each image's setting to be used.
The preview building process in Bridge has nothing to do whatsoever with the saving of image settings.
Also, if you are using any PhotoKit product, you need to update to the most recent version.

Batch Processing Issues - RAW to JPEG in CS3

Hi folks,
I recently upgraded to CS3 form CS2. Over the weekend, I spent several hours tweaking/adjusting about 200 RAW images in Bridge, that I need to convert to JPGs. I used a Photoshop Batch action that I created some time back in CS2 to convert the images from RAW ("Save As" as JPG), but it didn't include any of the adjustments that I made to the images during the conversion process, because I had Ignore/Suppress Open Dialog checked. I unchecked that, and re-ran the action but am now being prompted to open each image. I then modified the action to include the "Open" command. Running the script now still doesn't quite seem to work as I'd expected. The only adjustment that is incorporated is cropping, but it doesn't process any of the tonal/color balance adjustments. All images have the modification icon on them, indicating that changes were made, but the Photoshop Batch command isn't incorporating them when opened via the Batch Processing command. Any suggestions on how to get this to work?
I'm also very open to any other suggestions one may have on converting adjusted Camera RAW images to JPEG.
Thanks,
Kappabear

<[email protected]> wrote in message news:[email protected].. >I am having the same issue as the user above (kappabear)... I am going to >try the same options that PShock (Phil) gave...but what if I need to call >someone for assistance..(I'll even pay for support, because when I called >Adobe...they had no idea of what I was talking about)... Is there someone >that can give pay support??? > > I too just upgraded to CS3 and have a wedding to get out today, and 700 > images to save from RAW to JPG with many changes... Problem, I have a 6:00 > am flight to catch in the morning and I still need to pack.. (ANY HELP > from ANYONE would be greatly appreciated..) Ron, Due to news server propagation time issues, I'm seeing your post before the original one. I'm guessing others may be experiencing the same thing. Normally, I'd just wait for the earlier post to show up, but you're in a hurry. If you post again, and include enough of the post you are replying to, you may get more responses before your flight in the morning. -- Mike Russell - www.curvemeister.com

Anyone out there creating impulse responses?

Those of you that use sine sweeps to create your impulse responses, when you deconvolve them do they end up being the same length as your sweep file or does space designer create the proper length reverb tail?
When I attempt to create my impulse responses space designer does not create a reverb tail. It just seems to remove the sound of the sweep form the wet file.
Other convolution reverb programs that I have used create a reverb tail automatically and I believe sound designer should do this as well.
If anyone else is having this problem or has a fix for this issue please let me know. If not then if anyone out there is successfully capturing impulse responses using a sine sweep please post detailed step-by-step instructions on how you are able to do it.
At this point I am at wits end. I have contacted apple care only to find out that they don’t support space designer, so they were no help. You guys are my only hope…
Please Help
iMac Mac OS X (10.4.7)

The process is simple, but has many steps and they must be takin in the proper order:
Play the sweep tone into the space or reverb device while recording the output of the space or reverb device. If you use a reverb device, be sure to set the mix to 100% effect.
Be certain that the space or device you are sampling has fully decayed before you stop the recording. If you were sampling a 4 second plate reverb, do not stop the recording for at least 8 to 12 seconds after the sweep tone feeding the plate has ended.
Edit the resulting recording to eliminate 'dead space' before the sweep begins, and remove any excess space at the end of the file. Be careful not to truncate the decay portion after the end of the sweep.
Place the original sweep file and your edited recording of the effected sweep somewhere easy to find, I use a new folder and save them there.
In "Space Designer" press the "Deconvolution" button in the upper right corner. Load the effected sweep recording, then the original sweep signal and then save the resulting IR in a new folder.
Load the resulting IR file using the "IR Sample" menu and save the preset.
I've created hundreds of impulse files using sweep tones and it has always yielded proper reverb tail lengths for the space or reverb I was sweeping. In other words, if the sweep was 12 seconds long and the space I was sweeping has a 3 second RT60, the resulting impulse would be 3 seconds. On some files Space designer will create an impulse file which is much much too long. In these cases I remove the unnecessary minute or so at the end of the file and resave it.

Distill a folder of PS Files with Batch Process

We have just upgraded to Acrobat 8. Now a batch process is not working that has been in use since version 5. Please help.
Run /N2 acrodist.exe myTextFile
myTextFile:
/PathName (C:/PlotFile/In/862143A/*.ps) def /RunDir {{ /mysave save def dup = flush RunFile clear cleardictstack mysave restore } 255 string filenameforall } def PathName RunDir

> Thanks, this works. What exactly does the -f switch do?
I thought the reason was explained in a FAQ somewhere, but I can only seem
to find it as a forum response:
"To solve what was believed to be a security hole, by default, Distiller 8.1
no longer permits any file operations to be performed in PostScript. The
PostScript run operator is one such operation. The workaround is to invoke
the distiller with the -F flag. - Dov "
http://www.adobeforums.com/webx/.3bc4279f/2

Creating a moasic-batch processing question?

I 'volunteered' help to do a project for my daughter. For an
elementary school fundraiser, she wants to create four moasics -- 11X17 images --
one for each of four classes, with an 'Egyptian' theme -- at least one of the
images being of the pyramids of Giza.
The plan is this: several of the mommies will take their digital cameras to
school this week, and take photos of the children, and then let the children
snap away fill up the rest of the memory card. Assuming there are five
mommies, and that each provides a hundred photos -- they're going to put them
on CD's -- I could wind up with only 500 photos, and these moasic apps need
tons more images.
My 'plan', such as it is, is to take these photos and duplicate them as many
times as necessary, and then change the color cast of some of the different
batches, e.g. -- some with a 'blue' cast, some with a 'sand colored' cast, etc.
The idea is, MacOSaiX will choose the blue for the sky, the sand for the sand,
etc.
Questions: Given a big enough HD, and using PSE 4, can I easily duplicate
batches of the originals photos-- say 50 or a 100 at a time? Is there a
'batch' commend/process that would let me do that?
Ditto, changing the color -- can I apply the same color change to a large batch
of photos at the same time?
The PSE 4 Help seems to say I can 'batch process' all the files in selected
folders, but it doesn't mention duplicating all the images in the folder. It
does _seem to say that I could do the automatic 'color' adjustment.
Any help/suggestions to 'improve' this plan would be most appreciated.
Thanks,
Hal

That is what i ended up doing - basically batching up 100 items and then doing a service callout until all the items are processed (inside a pipeline pair). In this case I guess this works fine, but if this were a web service proxy instead of a MFL file proxy service it seems like the pattern is inefficient - I would do service callouts in the for each and aggregate the responses, then I'd need to call a service at the end (via a route) just to create a response (so it doesn't just echo the original request back). Or is there a better way?

Batch Process: Add Alpha Mask From File

I did a search for this, but couldn't find anything. If there is something, please feel free to send me in that direction.
I use Photoshop a lot for my 3D work. Usually, when I render an image sequence out, I have the mask saved in the alpha channel. Unfortunately, ZBrush doesn't allow me to do that, and instead saves the mask out as a separate image. I need to add the alpha mask to the color plate file. Is there any way to do this with batch processing?
--Andrew

AndrewRaz wrote:
Thank you for your response. I guess for now, I'll just add the masks by hand, since I don't know scripting at all.
It would be worth asking in the Scripting forum. There may be something available, in which case you just copy the file into the appropriate folder in PS and it's there on the menu to use.
Scripting forum.

BATCH PROCESS TO SELECT A DIFFERENT LINE OF PIXELS

Hi there,
I am trying to make my own slit scan image by selecting a single line of pixels from many frames.
From the first frame I would like to select the first line of pixels. From the second frame I would like to select the second line of pixels and so on. Then for this process to repeat itself.
It has been suggested that I can do this using the batch process in Photoshop however I cannot figure out how to do it!
If there is a simplier way then please get in touch.
Thanks
Elena

Hi,
This is the Photoshop.com forum, which is the online forum for Photoshop.com web site.
You'll get the best response if you post over in the below mentioned Photoshop forum:
http://forums.adobe.com/community/photoshop
Regards,
Komal

Batch Processing of records using JDBC adapter

Dear all,
We are working on JDBC-JDBC scenario and the flow is as below. Source is ORACLE and Target is SQL SERVER.
We need to pick up 2000 records from Source . PI should split them ito 4 batches of 500 each and should insert in SQL DB.While inserting the records, if there are any errors, those records should sent back to Source again. It is Synchronous scenario.
1) But as far as I know Batch Processing mode, INSERT option cannot be used.(From SAP help)
2) Will the connection break if we are sending the error records back to sender.
Any thoughts would be helpful.
regards,
babu

Hi,
The below links may help U.
JDBC ADAPTER
http://help.sap.com/saphelp_nw04/helpdata/en/7e/5df96381ec72468a00815dd80f8b63/content.htm
/people/saravanakumar.kuppusamy2/blog/2005/01/19/rdbms-system-integration-using-xi-30-jdbc-senderreceiver-adapter
/people/sap.user72/blog/2005/06/01/file-to-jdbc-adapter-using-sap-xi-30 - File to JDBC
JDBC - http://help.sap.com/saphelp_nw2004s/helpdata/en/64/ce4e886334ec4ea7c2712e11cc567c/content.htm
multiple tables with JDBC - http://help.sap.com/saphelp_nw04/helpdata/en/2e/96fd3f2d14e869e10000000a155106/content.htm
JDBC Response /people/swaroopa.vishwanath/blog/2006/12/28/send-rfc-to-sap-xi-150-asynchronous
Regards
Pullarao

Batch process recovery in ODI

I am very new to ODI.
I just want to know is there any solution available in ODI so that if any batch process fails then I can recover the data??
or is it so that in ODI when a batch process fails no data is get affected??

If the connection falls, then it depends on the JDBC driver used by ODI to connect the DBMS.
- If the driver reports that the connection is down, this will put the session in error.
- Most drivers just wait for a reply from the server, assuming that some "very long" processing is currently in progress on the database. ODI will also remain there, waiting for a database response. You would have to stop the session separately.
And yes, you can restart sessions in error.
Regards,
-FX

Batch Processing - Application Client

Hello,
I have a batch processing java program(application client) which does a certain activity. The batch processing program looks up Remote Stateless EJB's for performing certain business logic. I do not have any Connection Handling in the java program(application client). EJB's perform all the DB activity. Whenever my application client(java program) invokes the EJB's I see the DB connection going up significantly(3 times more than what is defined in data-sources.xml). When the application client is done and exits the DB connections come back to normal. Not sure why that would happen. Can someone throw any light ?
Note : Earlier we where using Oracle9i(9.0.3.0.0) and now we moved to Oracle10g(10.1.2.1.0). This behaviour is notice after the migration form Oracle9iAS to Oracle10gAS.
Appreciate quick responses..
Thanks.
Rajseh.

Indeed,
I found what was missing. I've had to go in Tools--> Application Settings and Batch Loader menu item is not been ticked.
Thanks for your help.
Regards

Error while processing a response

Hi, i have the next error while my class is processing the response. The
error is:
java.lang.NoSuchMethodError at
com.bea.portal.appflow.servlets.internal.PortalWebflowServlet.doGet(PortalWe
bflowServlet.java:214) at
javax.servlet.http.HttpServlet.service(HttpServlet.java:740) at
javax.servlet.http.HttpServlet.service(HttpServlet.java:853) at ...
My class only retrieve a param by request and send to response a image
archive from a DB. The code is:
response.setContentType(img.getMimetype().trim());
response.setHeader("Content-disposition","attachment; filename=\"" +
img.getNombre().trim()+"\"");
response.setHeader("Cache-Control", "no-cache");
response.setContentLength(img.getTamanoBytes());
try {
ServletOutputStream servletoutputstream =
response.getOutputStream();
servletoutputstream.write(buffer);
servletoutputstream.flush();
servletoutputstream.close();
catch (IOException ex3) {
throw new ProcessingException(ex3.toString());
The "img" object contains my image properties and the "buffer" variable
contains the byte array with the image.
Has anybody idea whats happening??
Thanks in advance.

Hi Sambo44,
Thanks for your posting!
I am not totally understanding your meaning. How did you get this error?Did you want to login on Azure form your VS? From your error message, I am not sure you can login on Azure portal using your account. Please make sure your account is right.
Or did you try to use ACS or WIF in your project for authorization? If it is , I suggest you can post this issue on Azure AD forum for more details.
Any question about this issue, please feel free to let me know.
Regards,
Will
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

In Bridge CS6, the "Tools" tab is missing the "Photoshop" option to batch process image

Hello!
Does anyone know why in Bridge cs6 under the "Tools" tab, my "Photoshop" option is missing? That is how I have always batch processed images. In Bridge, I choose the images to process, go to the "Tools" tab, down to the "Photoshop" option then to "Image Processor" and process. Now when I go into my "Tools" tab it only has the options: Batch Rename, 4 kinds of Metadata related options and Cache. Can someone tell me why this has happened and how to fix it? Thank you!!!
Eric

Hello Omke,
This problem lasted for two days. I tried many suggestions but nothing worked immediately. Suddenly I turned my computer on last night and it was fixed...inexplicably. Not sure what worked but something did. I appreciate you taking the time to offer advice.
Best,
Eric

Batch processing Impulse Responses

Similar Messages

Maybe you are looking for