Batteries for Power Mac G3 Beige Minitower

Where can I get batteries for Power Mac G3 Beige Minitower? I think they're Lithium batteries 3.6V 200W 922-4542.

m i g,
Here is a source for $4.99:
http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/
Jim
Note to others: (direct quote from above link)
This battery is an exact replacement for the below listed models.
Macintosh II series computers
Macintosh SE FDHD
Macintosh Classic (4-chip and 2-chip)
Macintosh SE/30, IIx, IIcx, IIci, IIfx, IIsi series computers
Macintosh IIvi, IIvx, Performa 600 series computers
Macintosh LC, LC II, LC III, Performa 400 series computers
Macintosh Quadra 605, LC 475, Performa 475, 477 series computers
Macintosh LC 520, LC 550, Performa 550 series computers
Macintosh Classic II, Color Classic, Performa 200 series computers
Macintosh Centris 610, 650, 660AV series computers
Macintosh Quadra 610, 660AV, 650, 700, 800, 840AV, 900, 950 series computers
Power Macintosh 6100, 7100, 8100 series computers, and Performa 6100 series computers
Power Macintosh 7200, 7300, 7500, 7600, 8500, 8600, 9500, and 9600 series computers.
Power Macintosh G3 - all models, entire series
iMac - all models, entire series
Power Mac G4 - all models, entire series
Power Mac G5 - all models, entire series

Similar Messages

Where can I get rid of an old Power Mac G3 Beige?

Where is the best place to get rid of an old Power Mac G3 Beige? Are there sites out there where Mac enthusiasts would buy it or its part? It has no hard drive. Also have the Multiple Scan 720 Display Monitor.

Glen.. I'm looking for some 256 sticks of RAM - PC-66 or 100 will do.. and if you want to move that CPU card - is it a Sonnet ZIF?
I have a Yosemite blue and white G3 that's living here while it's owner gets his living situation sorted out.. it was in rough shape as it sat in a few inches of water and is a bit corroded but not so much it's dead.
I'm cobbling it into a bit more stable, modern state for him so his 11 year old daughter can use it with her iPod. So far I have an 80GB hard drive and a Lite-on CD burner installed. I don't have much in the way of $$ right now, but can pay postage, if you want to part bits out. I can mail you a G3/266 processor to swap it out if you still want to have a working machine to part with.
I was going to use the bits from my beige for the Yosemite, but the Quicksilver that landed on my door turned out to be a boat anchor, so I bit the bullet and swapped out a power supply and got the G3 working again as a music server.
Am still on the hunt for freebie, useable parts..
Deb.

Can I upgrade straight from mac os 8 to mac os x 10.2 'jaguar' on my power mac g3 beige?

Can I upgrade straight from mac os 8 to mac os x 10.2 'jaguar' on my power mac g3 beige 'outrigger' desktop? There are two discs on ebay for 10.4.2 on ebay: http://www.ebay.co.uk/itm/Apple-Mac-OS-X-10-2-Installation-Discs-Jaguar-/2006580 32151?pt=UK_Computing_Software_Software_SR&hash=item2eb8269617#ht_466wt_64

Hi Aaron, should work if it meets these requirements...
System requirements
Supported Computers:[2]PowerMac G3, G4, early PowerMac G5, iMac, eMac, PowerBook G3 orG4, or iBook computer
Amount of RAM Required: 128 megabytes (MB) (Although 256 MB to 512 MB is highly recommended by many people who have used Mac OS X v10.2.8 as the real amount of RAM used when only the Operating System is running is around 200 MB, but it can be run with as low as 96 MB) although it will not run at full speed.
Processor Type: PowerPC G3, G4 or G5 running at 233 MHz or higher.
http://en.wikipedia.org/wiki/Mac_OS_X_v10.2
Except if it has a SCSI card...
http://docs.info.apple.com/article.html?artnum=86117

168 Pin RAm for Power Mac

Does anyone know if MT8LD864AG-6 168 pin DIMM is compatible with the RAM for Power Mac 8500 120MHz and Power MAc 7200 120 MHz?
Thank you in advance for your advice.
Robert

Hi Robert,
The ZIF processor upgrade I have in my Beige G3 MT (300 mHz originally) is a Sonnet G3/500--I wish it were a G4! I installed it when I still had OS9. It stayed in place when I installed Jaguar and, later, Panther.
As Grant mentions, I used a third-party helper program called XPostFacto, "XPF" for short. Installing "unsupported" Panther with XPF was far easier than installing the "supported" Jaguar and the computer is now more stable.
T'was Grant who talked me into trying Panther. Now I can't believe I waited so long! I used an older version of XPF, version 3.1, at Grant's suggestion. V3.1 seems to be the "sweet spot" for installing Panther. Some Beige G3 owners have successfully installed 10.4.x with later version of XPF but more users have reported stability issues than with 10.3.
If you are interested in learning more about the upgrade paths available to the Beige G3, there is a very active forum area here:
http://discussions.apple.com/category.jspa?categoryID=110
Hope this helps!
A

Need new low-end graphics card for Power Mac G5 (PowerPC 970)

My Power Mac G5 (PowerPC 970) has recently died I believe due to a bad
ATI RADEON X800 XT MAC EDITION video card.
Reason for thinking its the card, is that the machine was performing its intended tasks for several days even though the monitor was snow.
Having trouble determining a low-end replacement. (I no longer need the enhanced features of the RADEON X800 for this machine.
Much appreciated if someone could suggest a product appropriate for PowerPC 970.
Thanks!

I also ran into this issue with my dual G5. When I bought it, I didn't get wireless because it was a dedicated desktop on the network, but I'm upgrading and giving it to the kids to use in a room without wired network. Now that wireless would be really nice and it looks like the official solution is:
"Apple Wireless Upgrade Kit for Power Mac G5 Dual or Power Mac G5 Quad MA252G/A"
which is really expensive and difficult to install. But the weird thing is that I do have bluetooth. I wonder if there's just some little doodad I need to connect to get wireless going too, but I can't find any info on the card, and it looks like it's buried on the motherboard behind all the cooling stuff. I'll probably just spring for one of the USB solutions.

Power Mac G3-Beige: Continue to beep during start up

Why do my system beeps uncontrollably during start up? While booting it get stuck after desktop appears. I notice "add this to start up item" appear on window bar. This goes on for aprox. 10.minutes. HELP!
Power Mac G3 Mac OS 9.2.x Power PC / Beige
Power Mac G3 Mac OS 9.2.x Power PC / Beige

Welcome to the forum.
Was your Beige Mac booting up OK previously? When
did this beeping and freezing start? Did you add,
delete, or change anything, hardware or software
around the time that the problem started?
With the information you supplied so far, just a shot
in the dark but, it seems like some required startup
extension has been deleted or made inactive.
Give us more information and we may be able to help
you more.
Carl B.
If I can rember correctly, i beleive it started after completing a disk first aid on the system. I think I rember seeing a file named ___sprocket**###!!? I wish I could be of more discriptive.

DVI to s-video adpater for Power Mac G4?

I'm attempting to view digitial photos on my Power Mac G4 on an HDTV with an s-video connection. I've tried Apple's "DVI to video adapter" for the Power Mac G5, but it doesn't work, even after clicking "Detect Displays".
Is there a DVI to s-video adapater from Apple or anybody else that will work with the Power Mac G4? If not, are there any other options?

The Apple DVI to Video converter only works with certain graphics cards. The card has to be able to generate interlaced video at the correct scan rate, and modulate the color onto a carrier signal. For other card you would need a scan converter like:
<http://www.audiovisualdevices.com.au/viewprod.php?catid=&productid=CPT380>
This device has a VGA input, so you might need a DVI to VGA adapter. There may be other devices available with DVI input.

Dual monitor for Power mac g5 dual 2.3ghz

I wanted some advice on which monitors to get for a dual monitor setup and if its even possible to setup on my G5 or do I need a different video card?
Here's my computer spechs:
Power mac G5 dual core 2.3 ghz (late 2005)
Model: A1177
Memory: 2GB DDR2 SDRAM
HDD: 250GB
OS X 10.5.8 Leopard
The only thing I run on this is logic studio 8. I wanted to expand my setup but not sure how.
Any advice is greatly appreciated! Thanks
< Edited by Host >

It depends on which video card you have installed, though not much. Whichever card you have installed, you should have two DVI outputs available. With the minimum 256 Meg VRAM, you should be able to support two 1920x1080 monitors without a problem, and the "HD" monitors are getting very plentiful and dropping in price. Were I to buy today, I would make sure to get an LED monitor, as that flavor should have a longer overall life than a florescent panel monitor. You can find monitors in 23" dimensions for under $200 a pop, and more 27" monitors are showing up at a slightly bigger bite.

What is the max os upgrade available for power mac g5 w/powerpc processor

What is the max one can upgrade the os on a powerpc power mac g5

Hi, 10.5.8...
Leopard requirements/10.5.x...
    * Mac computer with an Intel, PowerPC G5, or PowerPC G4 (867MHz or faster) processor
minimum system requirements
    * 512MB of memory (I say 1.5GB for PPC at least, 2-3GB minimum for IntelMacs)
    * DVD drive for installation
    * 9GB of available disk space (I say 30GB at least)

Optical Fun for Power Mac G5 - Chosing a Burner

Hi all,
So I have a Power Mac G5 with a burner that is not so great anymore. I burn at 1x for DVDs and on good days, burn a CD at 4x. Time for a new burner you would say. I would agree.
I have a predicament and wondered if anyone suggests a burner to go with. I'm not looking to spend a lot and just want something that would work well and fit nicely.
I found two that might suit my little G5:
Pioneer
http://www.newegg.com/Product/Product.aspx?Item=N82E16827129007
LG
http://www.newegg.com/Product/Product.aspx?Item=N82E16827136119
Those two were Best Sellers at New Egg with nice reviews, but nothing on the Mac.
Does anyone have any other suggestions or anything that worked for you?
Has anyone used the brands above?
Thanks for reading and in advance for the help,
Bryant

Hi. The Pioneer 112D is often recommended in these forums - can't recall any adverse reports. I installed a previous version, the 110D, with no problems - works well.
The installation instructions are here
http://www.info.apple.com/usen/cip/pdf/g5/073-0807.pdf
Installation is a bit fiddly, but not difficult. There are two things to check: that the stand-offs (see Figure 8 of the installation instructions) are the right length to line the drive up with the aperture in the G5 casing - and that you remove the plastic bezel with CD, DVD, etc. on it from the front edge of the tray, so it doesn't catch on the edge of the aperture in the G5 casing - discussed here
http://discussions.apple.com/thread.jspa?messageID=4443213#4443213
If your current drive is a Pioneer, the stand-offs should be re-usable. If not, they may be able to be adjusted by not screwing them in fully, and then locking the thread with Loctite or similar.
The drive should be recognised in Blue Apple menu > About this Mac > More Info > Hardware > Disc Burning (System Profiler). If there are any problems, please post again. Good Luck.

External CD drive for power mac 8100

I have an 18 year old power mac 8100/80 AV. It has an internal CD drive that is read only. I need a cd drive that is read/write so that I can copy thousands of files off the mac. I'm assuming that an external drive may be the best route, rather than removing the old drive and installiing a new one. Can someone please advise on two points:
1. Is the external read/write CD drive the right way to go?
2. Where can I obtain said drive?
Many thanks.
i.forgot.all.i.knew

Jan and Ji~m,
Thanks for your suggestions. I have to say that I'm not yet sure what to do. I don't want to buy hardware unless I have to, and both of you appear to agree on this point. I plan to give away or recycle the powermac when I get the files off it as I have no use or space for it. I don't need to move the files to a CD; I need to move them to a PC (where I can read them) so I can get rid of the powermac.
The 2,500 files on the powermac are mostly in MS Word, in the first version that was PC and Mac compatible, so I believe I can read them with no problem on my PC when I get them there. Is this a good assumption? Or am I going to run into a conversion problem like Ji~m mentions?
I can't use the 3.5(?) inch "floppy" disk drive in the powermac because it gets formatted to mac-compatible before I copy files to it, and then the PC can't read it.
So I thought of the CD solution I mentioned in my first post because I believe a physical CD reads and writes on both the mac and the PC without being re-formatted. Is this correct?
I like the idea of a cable like Jan mentioned. I googled "AAUI to RJ-45 adapter" and can't tell from the pictures I viewed if I have a matching "AAUI Ethernet port" on the powermac. It has MANY ports, but nearly all are unlabeled! How do I determine what port might be the AAUI that Jan mentions?
If I use the cable suggestion (which I like), can I plug the other end into a PC? That's all I have -- this old powermac (OS 8.6) and several PCs (Dell and HP) with several OS's (W - XP, Vista, 7, and maybe 8). (Jan mentioned moving the files over a network, but the only "network" I have is my in-house router connecting my PCs to the i-net.) So how would I follow your cable suggestion?
Many thanks for all your help!
i.forgot.all.i.knew

Wich MacOS is the best for Power Mac G5?

Wich MacOS Can I update to a Power Mac G5? Somebody told me that the last one that I can update is the 10.5.8, maybe I can update it for a newest version but it can give me some troubles, is it true?

Hello,
10.5.8 IS the highest any G5 can go.
Just to be sure we're on the same page...
At the Apple Icon at top left>About this Mac.
Then click on More Info>Hardware and report this upto *but not including the Serial#*...
Hardware Overview:
Machine Name: Power Mac G5 Quad
Machine Model: PowerMac11,2
CPU Type: PowerPC G5 (1.1)
Number Of CPUs: 4
CPU Speed: 2.5 GHz
L2 Cache (per CPU): 1 MB
Memory: 10 GB
Bus Speed: 1.25 GHz
Boot ROM Version: 5.2.7f1

Can I use my new iMac 20" as a monitor for for Power Mac G5?

Actually I want to buy the new iMac 20" computer with the intel and then randomly use the iMac as a monitor display for my Power Mac G5 when I am editing video and then unhook it and use the Imac as a stand alone when I'm not editing video with my Power Mac. Will this work please. Thank You

Hello,
It's not possible to use either the iMac (Flat Panel) (G4) or the new Intel iMacs as displays. The only options would be:
VNC set-up. It's fairly low speed of refresh would probably make this undesirable for your situation: Screen Recycler (link)
A video-in device. A device like Elgato's EyeTV Hybrid (link) would not be of sufficiently high resolution to be any use for video editing.
regards
mrtotes

Tiger or panther - is there a version of tiger that works for power mac g4

I was searching for a version of Tiger that shows system requirements are compatible with a power MAC G4 - all I find is the 10.4 version of Tiger that shows system requirements as power PC G4 (not power mac G4). Wondering if anyone can help me out.

The B&Ws are strange beasts, see the bottom of this page for one instance...
http://eshop.macsales.com/item/Other%20World%20Computing/100SD256324/
Still I'm fairly certain it'll work, if worse comes to worse, I've used XpostFacto to install it on even older machines!

I need an inlet fan for Power Mac G5

I have a Late 2004 Power Mac G5 that needs an inlet fan any good websites?

Hey Miles, Of course the fans work. Why would I offer a non working fan? Anyway I need some info as to which fan you need. They are all called inlet fans. There is the two in the back the two in the middle that slide out for access to the memory and the one up by the hard drive / optical drive bay. The fans are all off my now dead Power Mac G5 Quad 2.5GHz. This is the PCI-X Quad so the Fans all seem to be the same as the DP PCI-X Macs but not 100% sure. Do you know the part # you need? I'll take a pic and post once I get home from work.

Batteries for Power Mac G3 Beige Minitower

Similar Messages

Maybe you are looking for