Battery Alert Notice?

For some reason my MacBook no longers provides me with the reserve battery alert when I'm nearly running out of battery. Instead it simply shuts itself off with no warning, i have also noticed that it occurs around the 30% mark. Any ideas?

Battery Information:
Model Information:
Serial Number:
Manufacturer: DP
Device name: bq20z951
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 002a
Hardware Revision: 0005
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 3375
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 3431
Health Information:
Cycle count: 324
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 12323
Hope this helps.

Similar Messages

My Hp Pavilion x2 10-020nr is showing a "Battery Alert" and will not start.

I've recently purchased the Hp Pavilion x2 10-020nr about a week ago, and have used it moderately everyday since.
I have not over-charged it or downloaded any malicious apps/software (as far as I know) but today I tried to turn it on after charging and all I got was a black screen that says
"HP Battery Alert.
The system has detected the storage capacity of the battery stated below to be very low.
For optimal performance battery may need to be replaced.
Primary (Internal Battery (001)
ENTER - Continue Startup"
and a link to this website...
Do I really need to replace the battery already? How do I fix this?? Did I do something???
I went through Amazon getting this tablet, should I contact them for a return? or is this issue resolvable?

Hello @Campbell1028,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that your notebook computer is displaying an error message, and I would be happy to assist you in this matter!
To further diagnose this issue, I recommend following the steps in this document on HP Battery Alert Appears Before Windows Starts. This should help test and calibrate the battery installed on your computer.
Additionally, I also suggest following the steps below re-install the Microsoft ACPI-Compliant Control Method Battery:
Step 1. Go to Device Manager
Step 2. Select Batteries
Step 3. Right click the "Microsoft ACPI-Compliant Control Method Battery" that is listed there
Step 4. Click Uninstall
Step 5. At the prompt put a check in the box to remove the current driver
Step 6. Shutdown the computer
Step 7: Remove the battery for minute and then put it back in
When the computer comes back up it should automatically find the driver.
Step 8. Go to Device Manager
Step 9. Select Batteries
Step 10. Right click the "Microsoft ACPI-Compliant Control Method Battery" that is listed there
Step 11. Click "Search automatically for updated driver software"
If the issue persists, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Hello, I am getting an HP Battery Alert, Do I need to replace?. It says it may need replacement.

I am wondering if I really do need to change my battery on my HP Pavillion dv7. my Pc is about 2 years old and just got that message when starting my PC.
It says HP Battery Alert
The system has detected the storage capacity of the battery stated below to be very low. For optimal performance, this battery may need to be replaced.
Primary (internal) Battery (601)
Enter- Continue Startup
For more information please visit: www.hp.com/go/techcenter/startup
Can you help me with this.???

Hello, I am getting an HP Battery Alert, Do I need to replace?. It says it may need replacement.[ New ]
08-12-2011 08:48 PM
I am wondering if I really do need to change my battery on my HP Pavillion dv7. my Pc is about 2 years old and just got that message when starting my PC.
It says HP Battery Alert
The system has detected the storage capacity of the battery stated below to be very low. For optimal performance, this battery may need to be replaced.
Primary (internal) Battery (601)
Enter- Continue Startup
For more information please visit: www.hp.com/go/techcenter/startup
Can you help me with this? how can i resolve it??

6750 How can I get a ''Low Battery Alert'' from my...

I have recently bought a 6750. At one point I realized that my phone died without any warning. Went through the User Guide, nothing.
Went through the phone and only found one thing under: >Settings > Tones > Other Tones, ON or OFF. I set it to ON.
Is this going to solve my problem or is there something else that I need to set?
How can a mobile not come by default with a low battery alert?
Maybe the OVI Suite should have a GUI to help setup the phone with all the proper instructions?

the only way to find out if warning tones set to on will work is to let the battery run low again
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Program start on critical battery alert

Hey,
in windows XP i had the possibility to start a program once the battery of my notebook reached the 0%mark (or in other words I could choose to start an application as an action on the "critical battery alert".) This feature was removed in Windows Vista :(
Will it be available in Windows 7 again? Is there anything I can do to catch this event with the task-scheduler? I searched the forum, no topics about it.
I did a google research - many people would like this feature.
I searched for the event-id of the critical battery alert in the event-log but didn't find anything.
has anyone any more information? Why has this feature been removed? How can i work around it without starting my application manually or leaving it running the whole time?
thanks,
alex

hi,
did you receive any solution/workaround for the problem stated above? please mail back if anything helped you at [email protected]
best,
astatine

IFS ALERT NOTICE FOR JDBC MEMORY LEAK FIX

IFS ALERT NOTICE FOR JDBC MEMORY LEAK FIX
Product and Version Affected:
Product: Oracle Internet File System
Product ID: 7
Version: 1.0
Description: There is a memory leak when retrieving or saving BLOBs through JDBC. IFS will appear to continue to increase in its memory consumption until the user runs out of swap space, and the machine stops functioning.
Platform Affected: Sun SPARC Solaris, Windows NT
Likelihood of Occurrence: Most iFS customers will notice this problem, since most will retrieve and store enough document content that they will notice the memory leak.
Symptoms:
- Performance becomes unacceptable on a minimally configured machine when doing significant retrievals and storage of documents.
- Significant swapping of the operating system.
- The user sees real memory and total memory continue to increase without bound when using any iFS protocols to retrieve and store document content.
- The memory usage goes back to normal when the iFS protocols are stopped.
Solution: Get the JDBC 8.1.6.0.1 patch for Solaris or NT (the OCI component, for JDK 1.1). Install it on all machines where the iFS protocols are running. The patch may be obtained on http://technet.oracle.com/software/tech/java/sqlj_jdbc/software_index.htm (you have to be logged into technet).
Be sure to get the OCI component of JDBC 8.1.6.0.1 for JDK 1.1.
null

Moving to Top

HP Mini 311 - HP Battery Alert - Primary (Internal) Battery (601) - Error Message at Startup

I have a HP Mini 311-1037NR (Product Number is VBM262UA#ABA). My OS is Windows 7 Home Premium.
When I start up my HP Mini 311 I receive the following message:
HP Battery Alert
The system has detected the storage capacity of the battery stated below to be very low. For optimal performance, this battery may need to be replaced.
Primary (Internal) Battery (601)
ENTER - Continue Startup
Here's are my questions:
First of all, what exactly is the problem here? From what I have googled, it would appear the problem is NOT my external battery, but my internal battery. What battery is needing replacement? Does it have a name?
Second, is there a user guide out there that would assist me with the replacement process that someone can provide a link to or at least send me the page that helps me? Is there a YouTube video (even better)?
Third, what exactly is the part number of the battery that needs replacement and exactly where do I purchase it (How much $$ does it cost)? This question is important as I may be able to find out how to replace the battery, but without a way to purchase the replacement battery I'm still dead in the water.
Fourth, my HP Mini 311 just dies when I unplug it. Will a remedy for the above issue remedy this issue as well? I really do enjoy using my little HP Mini, but would prefer to have the option to use it without a power cord.
Thanks in advance for any and all help.
Tim
This question was solved.
View Solution.

Hi Tim,
No problem and it's certainly wise to verify an answer.
I'd say you posted your question on the correct board. It's usually best just to post once on the relevant board. I do agree that the term 'internal' does cause unnecessary confusion.
Here's a link to your Maintenance & Service Guide.
Yes, I'm certain that the 601 error code refers to your notebooks main battery ( 602 is a failure code for machines that have a secondary storage cell ). Interestingly, there is no error code generated for a failing rtc battery - or any in built diagnostic test for it, just the usual symptom of the system clock re-setting after each shutdown.
There's also a HP document regarding start-up battery alerts on the following link.
http://h10010.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443470#N534
Best regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Hp battery alert 601

Hello. So upon start up of my notebook I would see a Hp battery alert 601 flash. This has been going on for months. My computer shut down on me as I was using it. When I turned it back on I saw the hp battery alert once again, it went to a system recovery screen, when I hit start with system repair a blue screen flashed and it shut down. I replaced the internal battery but when I restart the same hp battery alert screen still flashes followed by the windows recovery screen. If I select the startup repair it says problem cannot be fixed, if I select start windows normally it goes to the starting windows screen, the screen goes black and goes back to the hp battery alert screen. At this point I don't know what to do. Any suggestions please?

The battery needs calibrated or replaced.
To resolve a Battery Alert message, you should perform the Battery Test in the System Diagnostics (F2) environment, and calibrate the battery for best performance.
To access the HP System Diagnostics Battery Test , turn on the computer and immediately press the ESC key to display the Startup Menu. Press the System Diagnostics F2 key, and then select the Battery Test option.
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&docname=c01443470#N130

How do I turn off the low battery alert for my wireless keyboard?

The question is in the subject line. I find it kind of annoying to have to keep closing the alert window, and am still able to use the keyboard for a while past when the low battery alerts began. I tried system preferences for both alerts and for the keyboard but am not seeing how to adjust it there. Any help is appreciated! And yes I understand changing the batteries would probably help but I am comfortable using the full life of the batteries rather than changing them out right away.

Edit: Oh I found a possible, but drastic solution: disable the whole notification centre:
http://www.tekrevue.com/tip/how-to-completely-disable-notification-center-in-mac -os-x/
I haven't tested this long enough to know if it helps yet, but it is easy to turn on again. I am so annoyed with not being able to disable these warnings that I am more than happy to disable the whole notification centre, if that is what Apple wants us to do to sort this annoyance.

HP Battery alert

HP Battery Alert
The system has detected the storage capacity of the battery stated below to be very low. For optimal performance, this battery may need to be replaced.
Primary (internal) Battery (601)
ENTER - Continue Startup
For more information, please visit: www.hp.com/go/techcenter/startup.
My laptop model us pavilion dm4 and it was purchased in June 2011. Can you tell me what is wrong with battery and solution to it?

It is old and needs to be replaced.

No more "Low Battery" alert

hi,
my macbook doesn't give me anymore the "low battery" alert...
i can't understand why...
anyone could help me?
sorry for my english...

Have you ever calibrated your battery?
http://support.apple.com/kb/HT1490
Is your machine shutting down before your battery indicator gets very low... or is the display showing it has run out but just not giving a warning?
Reset your System Management Controller (SMC). This can sometimes help with power-related issues. Be sure to follow the instructions for your particular model as they vary from machine to machine:
http://support.apple.com/kb/HT1411
I would suggest resetting the SMC first as it is quick and simple. Calibrating your battery at this point may be difficult if your machine is not shutting down properly when your battery is low.

Battery recall notice - X100e, X120e, X200, X201, X201s series models

All,
If you have a ThinkPad X100e, X120e, X200, X201 or X201s model, please review this battery recall announcement on our support site. This page contains information on affected battery models, includes an automated test that will determine if your particular battery is affected and can order the replacement for you.
http://support.lenovo.com/en_US/detail.page?DocID=HF004122
Best regards,
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Hi moneytoo, welcome to the forums,
the part number is used to identify the batteries which need to be and should be checked using one of the methods described in the bulletin. It does not mean that all batteries with the listed part numbers will require recalling / replacing. Please also see the following post which has some more information about the part numbers;
http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/Battery-recall-notice-select-T410-T510-and-...
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

LOW BATTERY ALERT!!!

HEY! I OWN A SATELLITE A305-S6858 AND WHEN THE BATTERY GETS TO A LOW POINT I ONLY GET A QUICK ON SCREEN MESSAGE "10% BATTERY POWER REMAINING". I CAN NOT FIND AN AUDIO ALERT LOUD ENOUGH TO WARN ME RIGHT BEFORE IT SHUTS DOWN. I HAVE GONE TO CONTROL PANEL AND CHOSEN THE LOUDEST ALERT I COULD FIND BUT IT IS BARELY LOUD ENOUGH TO TAKE NOTICE. I AM USE TO A MUCH LOUDER AND REPETITIVE WARNING SYSTEM ON MY LAST LAPTOP (ALSO A SATELLITE).
ANY SUGGESTIONS/ADVICE ARE VERY MUCH APPRECIATED.

According to Microsoft this is by design.. check this out "Low" and "Critical" battery alarms do not sound on a Windows Vista based computer
HOpe this helps. Thanks!
peace on earth \m/

Wireless Keyboard - Low Battery Alert - Way to turn off?

I have a wireless keyboard (macbook late 2008 model running Lion) and while I've come to terms with the speed the thing eats away at batteries, I am most annoyed by the alerts telling me how low the battery is. I get alerts at around 15% and around 10% they pop up almost every 7-10 minutes, which is quite annoying if you're doing a bit of work. I would prefer to use my batteries until they run out or at least until they are 5% or less, yet the annoying alerts almost make me wish to throw them out now. Clearly the easiest solution is to just always use new batteries or rechargables, but I would prefer to find a method to just get rid of the warning altogether. Any suggestions would be appreciated.

To my knowledge, no.
Barry

Need help creating full battery alert using visual basic script

Hi,
I have been searching for resources, programs and code that will create an alert for me to unplug my charger when my laptop
battery is charged to full (or almost full).
The only problem with this code is that
Line 13: iRemaining (or RemainingCapacity called from BatteryStatus returns a 0 (might be a floating point which I can't figure out why). I even checked the microsoft documentation and its supposed to be a percentage.
I want to get either the current percentage of the battery or the total Fullchargedcapacity and the EstimatedRemainingCapacity to find the % of battery level.
Essentially what I am asking is how can I return the battery % using visual basic script.
Help!
The Code:
1 set oLocator = CreateObject("WbemScripting.SWbemLocator")
2 set oServices = oLocator.ConnectServer(".","root\wmi")
3 set oResults = oServices.ExecQuery("select * from batteryfullchargedcapacity")
4 for each oResult in oResults iFull = oResult.FullChargedCapacity
5 next
6
7 while (1)
8 set oResults = oServices.ExecQuery("select * from batterystatus")
9 for each oResult in oResults
10 iRemaining = oResult.RemainingCapacity
12 bCharging = oResult.Charging
12 next
13 iPercent = ((iRemaining / iFull) * 100) mod 100
14 if bCharging and (iPercent > 95) Then msgbox "Battery is at " & iPercent "%",vbInformation,"Battery monitor"
15 wscript.sleep 30000 ' (30 seconds)
16 wend

14 if bCharging and (iPercent > 95) Then msgbox "Battery is at " & iPercent "%",vbInformation,"Battery monitor"
On my Windows 7 machine your script returns the desired percentage (after adding the missing "&" to the right of "iPercent" in Line 14).

Battery Alert Notice?

Similar Messages

Maybe you are looking for