Battery drain and error in event log!!!

So I recently got a curve 9360, but battery life wasn't the 1 and a half days I expected. Doesn't last more than 5 hrs on normal use, and it falls drastically when doing slightly heavy work like now, bridged to my PlayBook like now, it turns of radio at about 30% then blacks out in under 5 minutes. So i did some digging around and most people said it was the OS, so I downloaded the os that most people say fixed there curve's, got a response for 7.1.0.190 and 7.1.0.258, bug still no difference. Out of curiosity I checked my event long and found this error ,
Name: System
Severity: Error
GUID: 97c9f5f641d25e5f
Time: "the date and time shown"
JVM:INFOp=mypin,a='7.1.0.190',o='9.6.0.24',h=e001507
So when I changed the os to 7.1.0.190, still got the same error and it's always at the top of the event log so am guess its what's causing the battery drain. Changed batteries, and wiped the OS and reinstalled but no solution.
Any help people!

Hi,
The Certificate Chain you installed on the FE server did not have "Enable all purposes for this certificat" enabled.
Run MMC--Add\Remove Snap-ins--certificates--Local Computer--Trusted Root Certificate Authorities--Certificates, find the certificate chain you installed--Properties--General, check the "Enable all purposes for this certificate".
Restart Lync FE server and check the problem is solved.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Similar Messages

VSS snapshot of 1.1TB is ending after few hours with timeout. No errors in event log

Hello,
does someone have experienced issue where starting making snapshot (forum GUI or command line) is taking a lot of time and then it just ends with timeout?
I have scenario on virtualised Windows Web Server 2008 R2 where backup is being made by Idera Backup Software but since it relies on VSS Snapshots then we can just skip this point because making snapshots from directly Windows command line or drive preferences/GUI
is ending with timeout for this single drive after few hours. Affected system has 3 drives: C - 95GB, D-1.06TB and E-120GB. C and E can be backuped correctly and only drive D has problems. System is updated with latest drivers vssadmin for writers returns
list without any errors and snapshot for drive D which ends with timeout is not generating any error in event log. I wanted to configure VSS trace like it is being instructed on this site:
http://publib.boulder.ibm.com/infocenter/tsminfo/v6/index.jsp?topic=%2Fcom.ibm.itsm.tshoot.doc%2Ft_pdg_traceprfrm.html
but I don't see any trace.txt file on given location. If I remove drive D from backup process it ends without errors. System was restarted many times. Only thing which is visible in windows Event log (application part) is that "The VSS service is shutting
down due to idle timeout." about 4 hours after snapshot making proces is starting.
I've contacted Idera backup about this but they can't help too much if Windows snapshot process is failing. They suggested that something can be wrong with this drive but since this is virtualised machine and all of my VM are being stored on RAID10 disk
array connected to my server using fiber connections then I don't think that this is hardware issue (especially when other two drives are located on the same LUN on disk array).
Any suggestions?
Regards

Hi,
Do you create VMs on Hyper-V or VMWare? Based on research, possible causes could be:
1. Files changes in the volume is very huge. So the shadow size may be big and the current shadow storage my not able to hold it. And that’s cause the shadow copy creation failure.
2. The I/O in D drive is heavy and make the shadow copy I/O failed.
3. Server is too busy to handle the request.
4. The disk is heavily defragment.
Please refer to the articles to troubleshoot the issue:
Time-out errors occur in Volume Shadow Copy service writers, and shadow copies are lost during backup and during times when there are high levels of input/output
http://support.microsoft.com/kb/826936/en-us
VSS timeouts during backup? What could contribute to that?
https://blogs.technet.com/b/askpfeplat/archive/2012/09/12/vss-timeouts-during-backup-check-fragmentation.aspx
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Error in event log

hi
from improper installation of coldfusion "Customer variable
in the registry I changed the configuration to the cookies but I
have error in event log
"An I/O operation initiated by the Registry failed
unrecoverably. The Registry could not read in or write out or flush
one of the files that contain the system's image of the Registry. "
and my registry is full, this key
HKLM/Software/Macromedia/coldfusion/CurrentVersion/clients
and each time you restart the coldfusion the old entered the
back regitre
thank for help
patrick

Hi Steve,
We need to confirm some situations:
1. Did this issue occur when you start Windows or specific application?
2. Could you let us know the complete event log?
And then If it's Windows startup issue, I suggest you perform a startup repair.
Startup Repair
http://windows.microsoft.com/en-IN/windows7/products/features/startup-repair
Meanwhile, Rename this file: %windir%\panther\setup.etl to setup.old and reboot to see if it could be resolved:
If it's one application issue, reinstall it for test.
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Allow Non-Administrator accounts to create event sources and write to event logs

We are setting up BizTalk 2013 in Windows Server 2012 and one of the requirements is to allow the service account to create sources and write in event logs (Application) of the BizTalk servers. We have found what it seems to be a simple solution for this
without giving service accounts local admin rights.
Give Full control for the following registry keys to the service accounts or groups to allow creating of event sources and write to event logs:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\EventLog
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\EventLog\Security
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\EventLog\Application
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\EventLog\Security
Note: when changing permissions for EventLog key, the child keys will inherit the permissions by default except Security key which must be done manually.
Initial tests using a .net test app seems to work as expected. New event sources are being created in the event logs and writing to the event logs after that works perfectly.
The above method has been deployed in production and this is the most suitable solution for us.

Hi Keong6806,
Thanks a lot for posting and sharing here.
Do you have any other questions regarding this topic? If not I would change the type as 'Discussion' then.
Best Regards,
Elaine
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Macbook Pro battery drained and now it won't turn on

I have an early 2012 Macbook Pro. A couple of weeks ago my charger broke and I couldn't get a new one straight away, so the battery drained and it shut off. I don't normally let that happen, but there wasn't a whole lot I could do about it this time. I have a new magsafe charger now and the LED is solid orange as normal, but the macbook still wont turn on even though it's been charging for a good 50 minutes now. It sounded like it was booting up a couple of times and the first time the screen lit up grey and the loading animation (grey bars) showed up, but now it's just black again. I know it's going to take longer than normal to charge after the battery being completely drained for so long, but is it normal for it to take so long or does it sound like it's bolloxed?

Try a SMC reset:
http://support.apple.com/en-us/ht3964
If no success, make an appointment at an Apple store genius bar for a FREE evaluation.
Ciao.

Iphone 4 overheated, battery drained and now wont take a charge?, iphone 4 overheated, battery drained and now wont take a charge?

ANy suggestions, iPhone 4 over heated , battery drained and now wont switch on - it does appear to be charging. Any help appreciated

Left it for an hour or so then took it off charge to cool down - should I leave it charging?

Missing VSS System Writer and CAPI2 error in Event Log

Hello,
I'm having problems with making full system backup of Windows 2008 R2 x64. It looks like this is related to missing VSS System Writer. When I'm running command "vssadmin list writers" there is no System Writer in writers list and in event log CAPI2 error (event ID 513) is showing with this description:
Cryptographic Services failed while processing the OnIdentity() call in the System Writer Object.
Details:
TraverseDir : Unable to push subdirectory.
System Error:
Unspecified error
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-CAPI2" Guid="{5bbca4a8-b209-48dc-a8c7-b23d3e5216fb}" EventSourceName="Microsoft-Windows-CAPI2" />
<EventID Qualifiers="0">513</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x8080000000000000</Keywords>
<TimeCreated SystemTime="2010-03-14T01:06:35.639125000Z" />
<EventRecordID>207975</EventRecordID>
<Correlation />
<Execution ProcessID="968" ThreadID="11588" />
<Channel>Application</Channel>
<Computer>System3</Computer>
<Security />
</System>
<EventData>
<Data>Details: TraverseDir : Unable to push subdirectory. System Error: Unspecified error</Data>
</EventData>
</Event>
any idea what could be wrong?
Thanks in advance

Hello ,
Based on the research, the VSS System Writer runs in the context of CryptSvc service on Windows Server 2008. To make the system writer works normally, please open services
console to verify that the Cryptographic Services logon as the credentials of the "Network Service" account.
The VSS system writer can be missing due to several reasons, to isolate this issue, please refer to the following steps to boot the problematic server with clean
boot mode to perform the test.
Steps: Clean Boot
1. On a problematic server perform a clean boot and check if the issue still exists
2. Click Start->Run...->type msconfig and press Enter
3. Click Services tab and select Hide All Microsoft Services and Disable All third party Services.
4. Click Startup tab and Disable All startup items
5. Click OK and choose Restart
After the server reboot, please run "vssadmin list writers" to check if the "System Writer" can be displayed.
If the issue still exists, please open a CMD prompt as Run As Administrator and type the following commands to see if it the system writer will be occure.
CD c:\windows\system32
Takeown /f %windir%\winsxs\filemaps\* /a
icacls %windir%\winsxs\filemaps\*.* /grant "NT AUTHORITY\SYSTEM:(RX)"
icacls %windir%\winsxs\filemaps\*.* /grant "NT Service\trustedinstaller:(F)"
icacls %windir%\winsxs\filemaps\*.* /grant "BUILTIN\Users:(RX)"
Moreover, based on the experience, it has been reported that there is some permissions issue which can cause this kind of issue. Please follow the steps below and check
if it can be helpful.
On domain controller
1. Open Active Directory Users and Computers
2. Click View and then "Advanced features"
3. Right Click built and click properties.
4. Click security tab.
5. Grant read permission to 'Authenticated Users'
6. Click Apply and OK.
7. Restart Cryptographic Services.
Note: By Default, it should have read permission for the system to take system state backup.
Hope this can be helpful.
MCTS: Windows Vista | Exchange Server 2007 MCITP: Enterprise Support Technician | Server & Enterprise Admin

Seemingly successful install of Exchange 2013 SP1 turns into many errors in event logs after upgrade to CU7

I have a new Exchange 2013 server with plans to migrate from my current Exchange 2007 Server.
I installed Exchange 2013 SP1 and the only errors I saw in the event log seemed to be long standing known issues that did not indicate an actual problem (based on what I read online).
I updated to CU7 and now lots of errors have appeared (although the old ones seem to have been fixed so I have that going for me).
Currently the Exchange 2013 server is not in use and clients are still hitting the 2007 server.
Issue 1)
After each reboot I get a Kernel-EventTracing 2 error. I cannot find anything on this on the internet so I have no idea what it is.
Session "FastDocTracingSession" failed to start with the following error: 0xC0000035
I did read other accounts of this error with a different name in the quotes but still can’t tell what this is or where it is coming from.
Issue 2)
I am still getting 5 MSExchange Common 106 errors even after reregistering all of the perf counters per this page:
https://support.microsoft.com/kb/2870416?wa=wsignin1.0
One of the perf counters fails to register using the script from the link above.
66 C:\Program Files\Microsoft\Exchange Server\V15\Setup\Perf\InfoWorkerMultiMailboxSearchPerformanceCounters.xml
New-PerfCounters : The performance counter definition file is invalid.
At C:\Users\administrator.<my domain>\Downloads\script\ReloadPerfCounters.ps1:19 char:4
+    New-PerfCounters -DefinitionFileName $f
+    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo
: InvalidData: (:) [New-PerfCounters], TaskException
    + FullyQualifiedErrorId : [Server=VALIS,RequestId=71b6bcde-d73e-4c14-9a32-03f06e3b2607,TimeStamp=12/18/2014 10:09:
   12 PM] [FailureCategory=Cmdlet-TaskException] 33EBD286,Microsoft.Exchange.Management.Tasks.NewPerfCounters
But that one seems unrelated to the ones that still throw errors.
Three of the remaining five errors are (the forum is removing my spacing between the error text so it looks like a wall of text - sorry):
Performance counter updating error. Counter name is Count Matched LowFidelity FingerPrint, but missed HighFidelity FingerPrint, category name is MSExchange Anti-Malware Datacenter Perfcounters. Optional code: 3. Exception: The
exception thrown is : System.InvalidOperationException: The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
   at System.Diagnostics.PerformanceCounter.InitializeImpl()
   at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
   at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 7384 is not running.
   at System.Diagnostics.Process.GetProcessById(Int32 processId)
   at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Performance counter updating error. Counter name is Number of items, item is matched with finger printing cache, category name is MSExchange Anti-Malware Datacenter Perfcounters. Optional code: 3. Exception: The exception thrown
is : System.InvalidOperationException: The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
   at System.Diagnostics.PerformanceCounter.InitializeImpl()
   at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
   at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 7384 is not running.
   at System.Diagnostics.Process.GetProcessById(Int32 processId)
   at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Performance counter updating error. Counter name is Number of items in Malware Fingerprint cache, category name is MSExchange Anti-Malware Datacenter Perfcounters. Optional code: 3. Exception: The exception thrown is : System.InvalidOperationException:
The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
   at System.Diagnostics.PerformanceCounter.InitializeImpl()
   at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
   at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 7384 is not running.
   at System.Diagnostics.Process.GetProcessById(Int32 processId)
   at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Issue 3)
I appear to have some issues related to the healthmailboxes.
I get MSExchangeTransport 1025 errors for multiple healthmailboxes.
SMTP rejected a (P1) mail from 'HealthMailbox23b10b91745648819139ee691dc97eb6@<my domain>.local' with 'Client Proxy <my server>' connector and the user authenticated as 'HealthMailbox23b10b91745648819139ee691dc97eb6'. The Active Directory
lookup for the sender address returned validation errors. Microsoft.Exchange.Data.ProviderError
I reran setup /prepareAD to try and remedy this but I am still getting some.
Issue 4)
I am getting an MSExchange RBAC 74 error.
(Process w3wp.exe, PID 984) Connection leak detected for key <my domain>.local/Admins/Administrator in Microsoft.Exchange.Configuration.Authorization.WSManBudgetManager class. Leaked Value 1.
Issue 5)
I am getting MSExchange Assistants 9042 warnings on both databases.
Service MSExchangeMailboxAssistants. Probe Time Based Assistant for database Database02 (c83dbd91-7cc4-4412-912e-1b87ca6eb0ab) is exiting a work cycle. No mailboxes were successfully processed. 2 mailboxes were skipped due to errors. 0 mailboxes were
skipped due to failure to open a store session. 0 mailboxes were retried. There are 0 mailboxes in this database remaining to be processed.
Some research suggested this may be related to deleted mailboxes however I have never had any actual user mailboxes on this server.
If they are healthmailboxes or arbitration mailboxes that might make sense but I am unsure of what to do on this.
Issue 6)
At boot I am getting an MSExchange ActiveSync warning 1033
The setting SupportedIPMTypes in the Web.Config file was missing.
Using default value of System.Collections.Generic.List`1[System.String].
I don't know why but this forum is removing some of my spacing that would make parts of this easier to read.

Hi Eric
Yes I have uninstalled and reinstalled Exchange 2013 CU7 for the 3<sup>rd</sup> time.
I realize you said one issue per forum thread but since I already started this thread with many issues I will at least post what I have discovered on them in case someone finds their way here from a web search.
I have an existing Exchange 2007 server in the environment so I am unable to create email address policies that are defined by “recipient container”.
If I try and do so I get “You can't specify the recipient container because legacy servers are detected.”
So I cannot create a normal email address policy and restrict it to an OU without resorting to some fancy filtering.
Instead what I have done is use PS to modify extensionAttribute1 (otherwise known as Custom Attribute 1 to exchange) for all of my users.
I then applied an address policy to them and gave it the highest priority.
Then I set a default email address policy for the entire organization.
After reinstalling Exchange all of my system mailboxes were created with the internal domain name.
So issue number 3 above has not come up.
For issue number one above I have created a new thread:
https://social.technet.microsoft.com/Forums/office/en-US/7eb12b89-ae9b-46b2-bd34-e50cd52a4c15/microsoftwindowskerneleventtracing-error-2-happens-twice-at-boot-ex2013cu7?forum=exchangesvrdeploy
For issue number four I have posted to this existing thread where there is so far no resolution:
https://social.technet.microsoft.com/Forums/exchange/en-US/2343730c-7303-4067-ae1a-b106cffc3583/exchange-error-id-74-connection-leak-detected-for-key?forum=exchangesvradmin
Issue number Five I have managed to recreate and get rid of in more than one way.
If I create a new database in ECP and set the database and log paths where I want, then this error will appear.
If I create the database in the default location and then use EMS to move it and set the log path, then the error will not appear.
The error will also appear (along with other errors) if I delete the health mailboxes and let them get recreated by restarting the server or the Health Manager service.
If I then go and set the retention period for deleted mailboxes to 0 days and wait a little while, these will all go away.
So my off hand guess is that these are caused by orphaned system mailboxes.
For issue number six I have posted to this existing thread where there is so far no resolution:
https://social.technet.microsoft.com/Forums/exchange/en-US/dff62411-fad8-4d0c-9bdb-037374644845/event-1033-msexchangeactivesync-warning?forum=exchangesvrmobility
So for the remainder of this thread we can try and tackle issue number two which is the perf counters.
The exact same 5 perf counter were coming up and this had been true each time I have uninstalled and reinstalled Exchange 2013CU7.
Actually to be more accurate a LOT of perf counter errors come up after the initial install, but reloading the perf counters using the script I posted above reduces it to the same five.
Using all of your suggestions so far has not removed these 5 remaining errors either. Since there is no discernible impact other than these errors at boot I am not seriously bothered by them but as will all event log errors, I would prefer
to make them go away if possible.

Errors in event log of Secondary DPM server protecting replicas on Primary

Hello again
I have two DPM servers, one situated on-site (primary) and one situated off-site (secondary). Protection jobs seem to be running correctly on both servers in that the jobs complete and I am able to restore data from the backups. I use the primary server
to make the initial backups of critical systems and data (Exchange MDB's etc) and the secondary server to backup those replicas off-site in case of primary site loss or DPM system loss.
The primary server is a physical server and the secondary server is a virtual server. Both DPM servers have their DPM databases stored on one physical SQL server that is in the primary site.
Basically what is happening is that every day our virtual machines are snapshotted (secondary DPM server included) and everyday the snapshot of the secondary DPM server fails. I see the following to entries in the event log of the secondary server.
Error 1:
WARNING
Source: MSDPM
Event ID: 955
The description for Event ID 955 from source MSDPM cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
The consistency check resulted in the following changes to SQL Server Agent schedules: Schedules added: 2 Schedules removed: 2 Schedules updated: 0.
Problem Details:
<ConsistencyCheck><__System><ID>26</ID><Seq>27861</Seq><TimeCreated>22/05/2014 23:01:31</TimeCreated><Source>SchedulerImpl.cs</Source><Line>719</Line><HasError>True</HasError></__System><Tags><JobSchedule
/></Tags></ConsistencyCheck>
the message resource is present but the message is not found in the string/message table
Error 2
ERROR
Source: MSDPM
Event ID: 4212
The description for Event ID 4212 from source MSDPM cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
DpmWriter service encountered an error during PrepareBackup as more than one component is selected for backup in the same snapshot set. Select a single DPM replica for backup and try the operation again.
Problem Details:
<DpmWriterEvent><__System><ID>30</ID><Seq>7</Seq><TimeCreated>23/05/2014 00:30:45</TimeCreated><Source>d:\btvsts\21011\private\product\tapebackup\dpswriter\vssfunctionality.cpp</Source><Line>438</Line><HasError>True</HasError></__System><DetailedCode>4212</DetailedCode></DpmWriterEvent>
the message resource is present but the message is not found in the string/message table
These two events are followed by another event from VMWare Tools everyday
Error 3:
WARNING
Source: VMWare Tools
Event ID: 1000
[ warning] [vmvss:vmvss] CVmSnapshotRequestor::CheckWriterStatus():1536: writer DPM Writer in failed state: res = 0x800423f4, err = 0x1, error =
Has anyone come across this before? Currently I am not quite sure what is going wrong and whether it is actually related to snapshots failing, but I want to try to fix these errors first and see what happens.
Regards

Your ar using VMware for Virtualization?
Are you trying to do an online Backup of the VM, think that will not work?
One thing i wonder, your have installed second DPM if Site one fails or goes done, but SQL for DPM2 is in Site one? try to move SQL to external site for DPM 2
Seidl Michael | http://www.techguy.at |
twitter.com/techguyat | facebook.com/techguyat

TREX 7.0 error in event log

A worker process with process id of '4316' serving application pool
'AppPool_SAP_TREX_02' has requested a recycle because it reached its
allowed request limit.
Hi I'm getting the above error in the system event log on my server. Has anyone seen this before?

- update TREX and KMC versions and patch levels
- see SAP note 845974 for recommendations

Adobe Air causing error in event log

I installed Windows 7 64-bit on a system recently. This morning I installed PS CS4, including Adobe Air.
I've now gotten 5 of these errors recorded in the event log.
Source: SideBySide
Event ID: 63
Level: Error
Activation context generation failed for "x:\adobe cs4\payloads\adobeamp-mul\adobe air\Versions\1.0\Adobe AIR.dll".Error in manifest or policy file "x:\adobe cs4\payloads\adobeamp-mul\adobe air\Versions\1.0\Adobe AIR.dll" on line 3. The value "MAJOR_VERSION.MINOR_VERSION.BUILD_NUMBER_MAJOR.BUILD_NUMBER_MINOR" of attribute "version" in element "assemblyIdentity" is invalid.
How do I get rid of this?

I have had the same issue since I bought PS-CS4 and Lightroom2.0 back in OCTOBER/NOVEMBER 2009.
Directly from Windows Event Log:
EventID 63: Activation context generation failed for "C:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Adobe AIR.dll".Error in manifest or policy file "C:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Adobe AIR.dll" on line 3. The value "MAJOR_VERSION.MINOR_VERSION.BUILD_NUMBER_MAJOR.BUILD_NUMBER_MINOR" of attribute "version" in element "assemblyIdentity" is invalid.
OS: Windows 7 64-bit
Considering this ERROR is CONSTANTLY being JACKED into the Event Log, I had hoped that others would be asking Adobe for a solution. I guess there are just two of us experiencing this problem - I seriously DOUBT that.
Having DEVELOPMENT experience in several programming languages, it appears there is a SIMPLE error in the DLL file. PLEASE FIX THIS ASAP!
As much as we have to pay for this software, I would expect not to have these kind of issues. Adobe PLEASE RESPOND!!!

Active Sync Error in Event Logs - Generated by Health Monitor Mailbox.

Receiving the event log entry below on an Exchange 2013 Mailbox Server (Server 2012 OS). No policies have been configured yet. Seems odd that by default the health mailbox would be blocked when default policy is allow. Anybody else seeing this?
Log Name:      Application
Source:        MSExchange ActiveSync
Date:          10/1/2013 11:59:16 AM
Event ID:      1021
Task Category: Requests
Level:         Warning
Keywords:      Classic
User:          N/A
Computer:      MYSERVER.mydomain.com
Description:
A non-compliant phone is trying to connect with Exchange ActiveSync. However, the Exchange ActiveSync mailbox policy for user [MYDOMAIN\HEALTLMAILBOXACCOUNT] and device ID [EASProbeDeviceId141] requires phones to be compliant before they synchronize with Exchange
ActiveSync.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="MSExchange ActiveSync" />
    <EventID Qualifiers="32772">1021</EventID>
    <Level>3</Level>
    <Task>1</Task>
    <Keywords>0x80000000000000</Keywords>
    <TimeCreated SystemTime="2013-10-01T17:59:16.000000000Z" />
    <EventRecordID>136375</EventRecordID>
    <Channel>Application</Channel>
    <Computer>MYSERVER.mydomain.com</Computer>
    <Security />
</System>
<EventData>
    <Data>MYDOMAIN\HEALTLMAILBOXACCOUNT</Data>
    <Data>EASProbeDeviceId141</Data>
</EventData>
</Event>

Did you find a solution for it?
I see the same error on our 4 Exchange 2013 Servers.
I have not. I just chalked it up to another broken item with Exchange 2013. Maybe it will be fixed by next year.

Oracle instance terminated with no error in Event Log

Hi all,
We are running ASP with VB COM 6.0 via Oracle Service for MTS against Oracle DB 8.1.7.4.1. As we always found the IIS down with error "New transaction cannot enlist in the specified transaction coordinator." in IIS server. At the same time, we found lots of error "Oracle Instance has been terminated" in event logs. However, we didn't find any error in alert log or trace file. Can anyone help to tell what's the instance error?
Also, we are running oracle client 8.1.7.4.7 and OraMTS 8.1.7.1.0.
If possible, please also help to solve the error "New transaction cannot enlist in the specified transaction coordinator.".
Thanks in advance.
Regards,
Joyce

Are you able to get the explain plan of the same statement directly at the sql*plus prompt?
This could be related to the bug:
Bug 3043373 : Abstract: MALFORMED EXECUTION PLAN IN V$SQL_PLAN WITH FILTER OPERATIONS
There is a patch available on top of the 9.2.0.6 version. The bug has been filed on the base data dictionary views in the database. To confirm, I would suggest that you verify the problem from sql*plus first.
Jaffar

[solved] No sound and AMD-Vi: Event logged

Hello,
Today I started to migrate my HTPC from openElec to Arch Linux since several things started to annoy me.
For now, I have made a fresh install and installed XBMC but I can't get audio. It is a AMD setup and has an Asus Xonar XD PCIe card installed. Integrated HD Audio is disabled.
The user xbmc is in the audio group and when I ssh into the HTPC and try to play a file with aplay I get tons of these on the TV:
[ 46.215678] AMD-Vi: Event logged [IO_PAGE_FAULT device=02:00.0 domain=0x0000 address=0x0000000000100000 flags=0x0050]
Channels are unmuted and I priorized the output with the following alsa-base.conf:
options snd slots=snd_virtuoso
options snd_virtuoso index=0
Alsamixer shows the desired sound card as default.
xbmc@xbmc ~ % LANG= aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: DX [Xonar DX], device 0: Multichannel [Multichannel]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: DX [Xonar DX], device 1: Digital [Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
xbmc@xbmc ~ % aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
default:CARD=DX
Xonar DX, Multichannel
Default Audio Device
sysdefault:CARD=DX
Xonar DX, Multichannel
Default Audio Device
front:CARD=DX,DEV=0
Xonar DX, Multichannel
Front speakers
surround40:CARD=DX,DEV=0
Xonar DX, Multichannel
4.0 Surround output to Front and Rear speakers
surround41:CARD=DX,DEV=0
Xonar DX, Multichannel
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=DX,DEV=0
Xonar DX, Multichannel
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=DX,DEV=0
Xonar DX, Multichannel
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=DX,DEV=0
Xonar DX, Multichannel
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=DX,DEV=0
Xonar DX, Multichannel
IEC958 (S/PDIF) Digital Audio Output
hdmi:CARD=HDMI,DEV=0
HDA ATI HDMI, HDMI 0
HDMI Audio Output
Setting iommu=pt as suggested here did not do any trick...
Does anyone here have a hint of what can be wrong?
Maybe this is interesting, too. The device, the AMD-Vi-Event refers to, is the mentioned sound card.
xbmc@xbmc ~ % lspci
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Root Complex
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) I/O Memory Management Unit
00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Trinity [Radeon HD 7480D]
00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller
00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Root Port
00:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Root Port
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 40)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 14)
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 01)
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)
00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD] FCH PCI Bridge (rev 40)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11)
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 0
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 1
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 2
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 3
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 4
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 5
01:00.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI Express-to-PCI Bridge (rev aa)
02:04.0 Multimedia audio controller: C-Media Electronics Inc CMI8788 [Oxygen HD Audio]
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 06)
Last edited by And1G (2013-08-20 13:43:11)

Can't anyone help on this one? I just checked with a Fedora 19 Live image (Kernel 3.9.5) and I get the same error messages in dmesg as in this Arch installation, also no audio.
I believe the problem here might not be directly audio related, but where could I search for the cause?
Also, I don't really think it's a hardware failure since audio is working nice with openElec (using Kernel 3.10, if I remember that right)...
Edit: So I've set up openELEC to boot (over PXE, so I don't have to reinstall everything) and sound is working out of the box. Here is some data for comparison to the above statements from the Arch system:
xbmc:~ # cat /proc/cmdline
root=/dev/ram0 rdinit=/init BOOT_IMAGE=openelec/KERNEL ip=dhcp boot=NFS=192.168.178.20:/srv/nfs/openelec disk=NFS=192.168.178.20:/srv/nfs/openelec overlay
xbmc:~ # uname -r
3.10.5
xbmc:~ # lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Root Complex
00:00.2 IOMMU: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) I/O Memory Management Unit
00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Device 9993
00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Device 9902
00:02.0 PCI bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Root Port
00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Root Port
00:10.0 USB controller: Advanced Micro Devices [AMD] Hudson USB XHCI Controller (rev 03)
00:10.1 USB controller: Advanced Micro Devices [AMD] Hudson USB XHCI Controller (rev 03)
00:11.0 SATA controller: Advanced Micro Devices [AMD] Hudson SATA Controller [AHCI mode] (rev 40)
00:12.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)
00:12.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)
00:13.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI Controller (rev 11)
00:14.0 SMBus: Advanced Micro Devices [AMD] Hudson SMBus Controller (rev 14)
00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller (rev 01)
00:14.3 ISA bridge: Advanced Micro Devices [AMD] Hudson LPC Bridge (rev 11)
00:14.4 PCI bridge: Advanced Micro Devices [AMD] Hudson PCI Bridge (rev 40)
00:14.5 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 0
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 1
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 2
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 3
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 4
00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 5
01:00.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI Express-to-PCI Bridge (rev aa)
02:04.0 Multimedia audio controller: C-Media Electronics Inc CMI8788 [Oxygen HD Audio]
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
xbmc:~ # aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: DX [Xonar DX], device 0: Multichannel [Multichannel]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: DX [Xonar DX], device 1: Digital [Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: Generic [HD-Audio Generic], device 0: ALC887-VD Analog [ALC887-VD Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: Generic [HD-Audio Generic], device 1: ALC887-VD Digital [ALC887-VD Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
xbmc:~ # aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
default:CARD=DX
Xonar DX, Multichannel
Default Audio Device
sysdefault:CARD=DX
Xonar DX, Multichannel
Default Audio Device
front:CARD=DX,DEV=0
Xonar DX, Multichannel
Front speakers
surround40:CARD=DX,DEV=0
Xonar DX, Multichannel
4.0 Surround output to Front and Rear speakers
surround41:CARD=DX,DEV=0
Xonar DX, Multichannel
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=DX,DEV=0
Xonar DX, Multichannel
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=DX,DEV=0
Xonar DX, Multichannel
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=DX,DEV=0
Xonar DX, Multichannel
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=DX,DEV=0
Xonar DX, Multichannel
IEC958 (S/PDIF) Digital Audio Output
hdmi:CARD=HDMI,DEV=0
HDA ATI HDMI, HDMI 0
HDMI Audio Output
default:CARD=Generic
HD-Audio Generic, ALC887-VD Analog
Default Audio Device
sysdefault:CARD=Generic
HD-Audio Generic, ALC887-VD Analog
Default Audio Device
front:CARD=Generic,DEV=0
HD-Audio Generic, ALC887-VD Analog
Front speakers
surround40:CARD=Generic,DEV=0
HD-Audio Generic, ALC887-VD Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=Generic,DEV=0
HD-Audio Generic, ALC887-VD Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=Generic,DEV=0
HD-Audio Generic, ALC887-VD Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=Generic,DEV=0
HD-Audio Generic, ALC887-VD Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=Generic,DEV=0
HD-Audio Generic, ALC887-VD Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=Generic,DEV=0
HD-Audio Generic, ALC887-VD Digital
IEC958 (S/PDIF) Digital Audio Output
Not a single one of these AMD-Vi Events is in the dmesg output.
Does anyone have a clue on how I could figure out if they installed uncommon patches or use weird parameters to get all this running?
Edit #2:
So I've searched through some of these odd IOMMU options and found this: https://www.kernel.org/doc/Documentatio … ptions.txt
I tried iommu=soft as a kernel parameter and I get audio output and the AMD-Vi Events are no longer present. But can anyone explain to me what exactly I have done here? Using a "software bounce buffering" seems weird to me if I have some hardware present, that can do such things (The IOMMU, I assume)...
Since this really does not look like only audio-related problem, can someone perhaps move the thread to the right place. Although I'm not quite sure which this will be.
Last edited by And1G (2013-08-19 22:12:20)

Crystal Reports Error in Event Log

Hi all,
I have an error in my events Logs on my Windows server 2003 Server. The Event ID is 4353 and the descirption is : "Either the keycode registry entry does not exist, or the process does not have sufficient permissions to read the keycode.'
I use CR XI.
Since I Have this error message I Can't load my reports.
Any ideas about this case?
Thanks in advance.
Xavier.

Thanks Graham but I don't have this key in the regitry.
In fact, I only use CrystalReports11_NET_EmbeddedInstall.msi to install Crystal Reports DLL.
Any ideas?
Thank you.
Xavier.

Battery drain and error in event log!!!

Similar Messages

Maybe you are looking for