Battery indicator on my G4 not giving me correct reading
My intention was to calibrate the battery, so i let it run down to 0%, but has been on for over 1/2 hour, and hasn't shut down yet....
Once it does run down, finishing the calibration procedure will, hopefully, make the battery indicator more precise. That's actually one of the reasons to calibrate the battery.
From http://support.apple.com/kb/ht1490 :
The battery has an internal microprocessor that provides an estimate of the amount of energy in the battery as it charges and discharges. The battery needs to be recalibrated from time to time to keep the onscreen battery time and percent display accurate and to keep the battery operating at maximum efficiency.
If you never see the low battery warning, you may want to try resetting the PMU.
Similar Messages
-
Report not giving Output correctly
hi all
The problem is about Pending invoice report. But this report is not giving output correctly.
Plz help me to solve the problem.
Thanks
SubhasishHi Mishra,
Invoice output is coming correctly- assuming you have calculation error then check the print program assigned to your invoice output condition type. It must be having some logic error.
If the issue is with improper formatting then check the layout assigned to your invoice output conditon. You can check both the program and layout assingment to ouput condition at NACE transaction.
This is regular task which abapers can do with ease. so please take their help. They can just do a simple debug to understand the issue.
regards
sadhu kishore -
Query not giving the correct result
select Project_id, contractno
from elf_transactions
where(rtrim(contractno),rtrim(project_id)) not in
(select rtrim(contractno),rtrim(projectid)
from contract_proj
where report_month='1-May-2007' )
when I m firing this query, it is not giving correct result to me, it also select the recorts which are matches in both the table
i want to fine out those contract, with projectid which are not in contract_proj table
Please help me in this regardCREATE TABLE ELF_TRANSACTIONS
VENDOR_ORDER_REF VARCHAR2(60 BYTE),
BT_SUB_CON_REF VARCHAR2(10 BYTE),
PR_NO VARCHAR2(15 BYTE),
PO_NO VARCHAR2(15 BYTE),
PR_PO_DESCR VARCHAR2(200 BYTE),
ONE_IT_PROG VARCHAR2(50 BYTE),
BT_DEL_MANAGER_NAME VARCHAR2(40 BYTE),
DELIVERY_TYPE VARCHAR2(5 BYTE),
ACTUAL_DEP_DATE DATE,
ASSOC_ASG_BR_QUE VARCHAR2(50 BYTE),
PRE_AVG_P1_P2_INC_CNT NUMBER(3),
POST_P1_P2_INC NUMBER(3),
PERC_GROWTH_POST_REL NUMBER(3),
VENDOR_DEL_MANAGER VARCHAR2(50 BYTE),
REPORT_MONTH DATE,
COMMENTS VARCHAR2(200 BYTE),
PROJECT_ID VARCHAR2(20 BYTE),
CONTRACTNO VARCHAR2(15 BYTE),
CONTRACT_TYPE NVARCHAR2(15),
IDUNO VARCHAR2(10 BYTE),
STATUS VARCHAR2(10 BYTE),
DESCRIPTIONCODEDELIVERABLE VARCHAR2(255 BYTE),
UNIQUEID VARCHAR2(255 BYTE),
LOCK_RECORD CHAR(1 BYTE),
VERIFIED CHAR(1 BYTE),
VERIFIED_BY VARCHAR2(40 BYTE),
BT_VERIFIED CHAR(1 BYTE),
BT_VERIFIED_BY VARCHAR2(40 BYTE)
CREATE TABLE CONTRACT_PROJ
CONTRACTNO VARCHAR2(10 BYTE),
PROJECTID VARCHAR2(20 BYTE),
IDUNO VARCHAR2(10 BYTE),
CH_EMPID VARCHAR2(8 BYTE),
CHNAME VARCHAR2(40 BYTE),
GH_EMPID VARCHAR2(8 BYTE),
GHNAME VARCHAR2(40 BYTE),
PM_EMPID VARCHAR2(8 BYTE),
PMNAME VARCHAR2(40 BYTE),
SPM_EMPID VARCHAR2(8 BYTE),
SPMNAME VARCHAR2(40 BYTE),
PRJ_MONTH DATE,
BT_CONTRACT CHAR(1 BYTE)
REPORT_MONTH COMMENTS PROJECT_ID CONTRACTNO CONTRACT_TYPE IDUNO STATUS DESCRIPTIONCODEDELIVERABLE UNIQUEID
06/01/2007 00:00:00 1287 TML007452 OPEN Delivery of CRs DM CD and NSI N/A
06/01/2007 00:00:00 1280 TML007452 OPEN Delivery of CRs H&W OOR and WLTO N/A
06/01/2007 00:00:00 1231 TML007452 OPEN Delivery of CRs H&W OOR WLTO
06/01/2007 00:00:00 1097 TML007679 OPEN High Level Roadmap for Global Services and Wholesale with Feasibility study into BTR access to Switc N/A
06/01/2007 00:00:00 405 TML007942 OPEN RTRCC DEVELOPMENT -Q107
06/01/2007 00:00:00 405 TML007919 OPEN WLR3 DEVELOPMENT-Q107
06/01/2007 00:00:00 1170 TML008439 OPEN R-510
CONTRACTNO PROJECTID IDUNO CH_EMPID CHNAME GH_EMPID GHNAME PM_EMPID PMNAME SPM_EMPID SPMNAME PRJ_MONTH BT_CONTRACT
MBT003060 176 BT06 8694 Soman Sameer Surendra 1054 Bhadti Shripad Shivram 1054 Bhadti Shripad Shivram 1420 Rao Darbhamulla Kameswara 05/01/2007 00:00:00 N
MBT003842 1156 BT12 19992 Kalle Ajit Ashutosh 1539 Padgaonkar Shailesh Vishwanath 13948 Khunte Milind Vasant 16426 Kulkarni Vinay 05/01/2007 00:00:00 Y
MBT004677 458 BT09 20275 Mundassery George 5044 Kamalapurkar Leena Shrinivas 12849 Dave Ajay Yogeshchandra 2017 KIRKIRE SONAL MADHUKAR 05/01/2007 00:00:00 N
MBT004695 362 BT13 20276 Ghosh Sankar 2624 Avachat Jagdish Vasantrao 13592 Pal Sudipta 2624 Avachat Jagdish Vasantrao 05/01/2007 00:00:00 N
MBT004826 VITRIA BT09 20275 Mundassery George 26099 Saha Debendra Kumar 28134 Hinge Anand Sharad 12777 Karandikar Sumedh Vidyadhar 05/01/2007 00:00:00 Y
MBT004924 1027 BT03 1451 Tillu Ashirwad 15693 Devaraj Daniel G 6867 Jadhav Satyajit Ramesh 15693 Devaraj Daniel G 05/01/2007 00:00:00 N
MBT004927 1025 BT05 4436 Kelkar Subhash Manohar 20379 Gore Sujeet Narayan 13704 Vignesh Chandrasekaran 4347 BIJNORI REHANA GULAMWARIS 05/01/2007 00:00:00 N
MBT004927 1092 BT05 4436 Kelkar Subhash Manohar 15094 Jain Jitendra 13350 Bokil Shripad Raghunath 9511 Markande Balchandra Narayan 05/01/2007 00:00:00 N
MBT004927 1213 BT09 20275 Mundassery George 19996 Vege Sridhar 16401 Sibgathulla Mohammed 19996 Vege Sridhar 05/01/2007 00:00:00 N -
MOD not giving up correct values
Hi everyone,
I am having problem on using MOD in Director, i wrote the
following in director:
put (3054452055 mod 16)
-----giving result "-9"
The value/result it gives me is not correct. It should be
"7". But director is giving me "-9".
So, the same thing i did in FLash by just simply putting the
following:
trace(3054452054445%16);
and it gives me correct answere.
So, i want to know why Director is mis calculating the simple
calculations ??
AmirIf I'm remembering correctly, the cause of your problem is
that lingo ends up returning strange negative numbers if the result
of your equation is greater than a certain number (Often it's
-2147483647 but I suppose it could return -9 because of the MOD
part of the equation) You can find more information on this
here.
Best of luck,
Johnathon -
Acrobat 7 not giving in to Reader XI
Need to have my Acrobat 7 to give in to reader in google crome for form filling online sites. any Ideas, using windows xp, and on 64bit.
If you have questions about using your software you should ask questions in the forum for the product involved.
Here is a link to a page that has links to all Adobe forums...
Forum links page:
http://forums.adobe.com/index.jspa -
Case condition is not giving the correct result in Union query
Hello PL/SQL Gurus,
I am using Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production version
I have a table in following format -
drop table TT2;
create table TT2(FeeDate,Clerk,ClrComm,ExComm,TagComm) as select
20120102,'Mathews',25,56,245 from dual union all select
20120102,'Lika',0,56,245 from dual union all select
20120102,'Ram',0,0,245 from dual union all select
20120102,'Angilo',NULL,NULL,245 from dual union all select
20120102,'Nikki',225,NULL,245 from dual union all select
20120103,'Ram',NULL,556,2345 from dual union all select
20120103,'Lika',NULL,NULL,245 from dual union all select
20120103,'Mathews',25,56,245 from dual;DML Used -
SELECT FEEDATE,CLERK,SUM(ClrComm) ClrComm,null ExComm,null TagComm,sum(case when ClrComm>0 then ClrComm end) Comm
from tt2
group by FEEDATE,CLERK
UNION
SELECT FEEDATE,CLERK,null ClrComm,sum(ExComm) ExComm,null TagComm,sum(case when ExComm>0 then ExComm end) Comm
from tt2
group by FEEDATE,CLERK
UNION
SELECT FEEDATE,CLERK,null ClrComm,null ExComm,sum(TagComm) TagComm,sum(case when ClrComm=0 or ClrComm is NULL and ExComm=0 or ExComm is NULL then TagComm end) Comm
from tt2
group by FEEDATE,CLERKResult Output -
FEEDATE CLERK CLRCOMM EXCOMM TAGCOMM COMM
20120102 Angilo 245 245
20120102 Angilo
20120102 Lika 0
20120102 Lika 56 56
20120102 Lika 245 245
20120102 Mathews 25 25
20120102 Mathews 56 56
20120102 Mathews 245
20120102 Ram 225 225
20120102 Ram 0
20120102 Ram 490 490
FEEDATE CLERK CLRCOMM EXCOMM TAGCOMM COMM
20120103 Lika 245 245
20120103 Lika
20120103 Mathews 25 25
20120103 Mathews 56 56
20120103 Mathews 245
20120103 Ram 556 556
20120103 Ram 2345
20120103 Ram
Output expected -
FEEDATE CLERK CLRCOMM EXCOMM TAGCOMM Comm
20120102 Mathews 25 56 245 81
20120102 Lika 0 56 245 56
20120102 Ram 0 0 245 245
20120102 Angilo 245 245
20120102 Nikki 225 245 225
20120103 Ram 556 2345 556
20120103 Lika 245 245
20120103 Mathews 25 56 245 81I sincerely thanks to all of you for your effort in advance.This way:
select feedate, clerk, clrcomm, excomm, tagcomm,
sum(decode(nvl(clrcomm, 0) + nvl(excomm, 0), 0, tagcomm, nvl(clrcomm, 0) + nvl(excomm, 0))) over (partition by feedate, clerk) comm
from tt2
order by feedate, clerk;
FEEDATE CLERK CLRCOMM EXCOMM TAGCOMM COMM
20120102 Angilo 245 245
20120102 Lika 0 56 245 56
20120102 Mathews 25 56 245 81
20120102 Nikki 225 245 225
20120102 Ram 0 0 245 245
20120103 Lika 245 245
20120103 Mathews 25 56 245 81
20120103 Ram 556 2345 556
8 rows selected -
Do I need the battery indicator?
I'm having a repair done and they tell me the battery indicator is faulty. Does it do anything more than just show battery life via the lights on the side? Will the computer operate normally without it? Will the onscreen battery icon still work? Just wondering if I need to spend the extra $$. Thanks guys!
Hey Surface_Dweller,
Thanks for the question. After reviewing your post, it sounds like you want to know what exactly the battery indicator does. I would recommend that you read this article, it may be able to help you.
About the battery indicator lights on MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (Late 2008 and later)
http://support.apple.com/kb/HT3205
The battery indicator lights are located along the left side of the computer. This allows for quick and easy verification of the battery's charge status while the computer remains solidly in-place.
Thanks for using Apple Support Communities.
Have a nice day,
Mario -
My battery indicator is on green but the percentage is not showing on the phone
My phone was working fine this morning then suddenly on the home screen the battery percentage disappeared. It was at 56 percent when it disappeared. I shut the phone down, that did not change it. I checked the battery indicator and it was still set to green. I shut it off and then turned it on again. Still no percentage showing on my phone. Any suggestions would be appreciated.
Since you have already performed a restart, the next user step is a reset. Hold the sleep/wake and home buttons together until you see the Apple logo and then release. The phone will reboot. Check then.
-
My 13.3" macbook pro will not power up.The battery indicator light does not come on.The Mag safe charging light flickers green and red dimly.I had a cell phone connected to the USB port.
This didn't work for me, so I did a bit of searching and TONS of pages later in google, I found an answer. Here are the steps for people who also were in my situation:
1. Take off bottom case
2. Unplug battery - blurry image here: http://i.ytimg.com/vi/03cC79r5Dx4/0.jpg
3. Press and hold power button for 5 seconds
4. Plug a charger in, and it should start booting up
5. After shutting down again, reconnect the battery and close the case up
6. It works! (hopefully, if you guys had the same situation I did) -
Took apart Macbook pro 13 to remove broken headphone tip in the jack. Had to remove battery to get to the headphone jack. Now the laptop won't start. The power button is just not responding. Battery indicator showed charge of 3 dots initially but now only the last dot is blinking. The power cable used to light up green initially but now the green light is gone. I have tried SMC reset, which didn't work. What are my options?
Macbook Pro2067 wrote:
<snip>
What are my options?
Take it to an authorized service center. -
Note that the iPod touch 5th generation was updated to iOS 8. When I connect my charger to my iPod touch, for the first time, the battery indicator does not update when connected to a power source. Instead of being charged, it says that the battery is being depleted. Please fix this issue. Thank you!
Not Charge
- See:
iPod touch: Hardware troubleshooting
iPhone and iPod touch: Charging the battery
- Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
- If a 5G iPod
Iphone 5 lightning port charging problem - SOLUTION!
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
Another battery indicator issue-- not 1.1.1 related
Sorry if this is a repeat. I searched for this and didn't find it, though it seems like something that should have been reported before. Am both asking if others have the issue/how it was solved and offering my experience as possible help.
3 week old phone. Firmware 1.0.2 (never updated to 1.1.1, not a downgrade). Never hacked.
Phone has been working fine, was getting 100% charge, plug icon achieved w/ full green glowing icon when charged. Usage after my last full charge: probably 2-3 hours phone, frequent mail, some wi-fi, standby for 2.5 days.
Bluetooth on all the time, wi-fi only on during use, screen brightness turned down to ~30%, manual mail checking only, usually in excellent reception areas so phone not constantly searching for signal.
Put phone to sleep last night w/ battery indicator @ ~50%. When tried waking phone this morning it, for the first time, showed message saying phone needed to be plugged in and showed the large battery icon with a very thin red line representing charge remaining and turned itself off. So I plugged the phone into the wall adapter and the charging icon came on with a sliver of red (slightly wider than when not plugged in).
Did some reading online and unplugged the phone maybe 10 minutes after plugging it in-- with charge icon still showing thin red area, unchanged from initially. After unplugging the small menu icon had a red sliver of charge showing but the phone did not automatically turn off, though that was for only maybe 10 seconds or so.
Then I did a reset w/ menu-sleep buttons. After the phone rebooted there is maybe 40% of battery life on menu indicator. I replugged the phone into the wall charger for a better look and the large icon shows about the same-- 40%. I unplugged phone immediately and have been monitoring it for about an hour. Still at roughly 40% and phone function working normally as does everything else, including video-- though that drains battery indicator pretty quickly.
I know that there is rapid charge when first plugged in but I don't think that 10 minutes would take it from the 10% shutoff point to this degree of charge. My guess is that it's an intermittent problem with the phone's internal battery sensing abilities which gets reset with a phone reset.
The good news is that the phone is functional when it thinks it's not. The bad news is that a) a reset is a mild pain in the neck. (Could be that just fully turning the phone off and restarting it would have worked but I didn't try that. Other than losing usage data I don't know what else one loses with a reset.)
and b) it is unnerving to not be able to trust the battery indicator, especially when one isn't near a convenient charging option.
So, anyone else had this same issue? Thoughts, fixes?
Thanks
SteveHi there,
I would recommend that you take a look at the troubleshooting steps listed in the article below.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
-Griff W. -
I can not open Gallery, and my battery indicator d...
hello!
I've a problem that I can not access my gallery to see my photos, on my N70. I guess I have to install an application but I could not find any on the nokia website.
my second problem is that my battery indicator is not functionnig at all it indicates always "full".
thanks for providing me with the solutionsHello!
when I press to enter the gallery, the background image appears and then disappears. no phone block.thus it does not open.
for the battery, I tried the hard reset, he asks for the code, I entered it but he does nothing until I press cancel, where it return back to its initial state (On state).
I searched for the N70 software update but I could not find it, can you please give the PATH.
I appreciated your fast reply.
Thanks -
Torch battery indicator not right
I'm using a Torch 9800 on AT&T, OS is 6.0 bundle 2647.
My battery indicator is reporting that the battery is draining very rapidly.... it gets to zero in an hour or two, but the device keeps running all day long without actually running out of power. I've turned off GPS, WIFI, BT, and dimmed the screen. When I pull the battery and reinsert it, the indicator goes back to indicating a nearly full charge, but then indicates (erroneously) that it is rapidly losing it's charge, getting back to zero in a couple of hours. I've swapped batteries with a coworker and had the same results. It even stays at zero when plugged in to the charger, even though I know the battery is charging.
Any ideas?Your "on-device" battery meter is not updating or correctly calculating the battery charge.
There are a couple things I can recommend:
upgrade your device operating system.
Connect your device to a wall outlet charger, and allow it to charge an hour or so, and while STILL connected to the charger, remove the battery on the device for a minute, replace and reboot. See how it goes on the meter, and if it doesn't get straight, refer back to #1.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
NOT SOLVED!!!! N9 (battery) indicator LED
How can you say "solved" on a thread still unsolved???:
/t5/Maemo-and-MeeGo-Devices/N9-battery-indicator-LED/td-p/1181277
Tell me where is your solution in that thread? Nokia ..you should find personnal who really know how to treat posters and really make an effort to solve our issues OR just close down this forum!
5800-E72-N80-N9-Iphone-BB
I like all the phones in my household but the N9 is a big disappointment :
Low ring tones
Led doesn't work
Arabic Language interface taking too long
Doesn't support Nimbuzz
Division of memory has no logic
I regret buying this phone and am trying to sell it for any price right now.Same issue here.
I bought my N9 one week ago from a Nokia Store (in Turkey), and its LED too is not blinking when charging. So I went to the store to ask them to change the phone but they reject my request. And more interestingly, its the second N9 that they gave me. Because the first one I bought had had a double tap unlock problem and they had changed it unquestioningly (I do not know if the first one had the issue) .
I'm really furious with Nokia now. They sold me a phone which is with that issue, it is their fault. But I am the one who is reduced to use that failing phone.
Good for you Nokia. Keep going like that and make us hate you. Actually I am the real idiot here. Why on earth did I not bought an iPhone 4S or something else instead this godd*mn phone?
Maybe you are looking for
-
Hi all, I tried to use the migration to EJB 3.0 of the Adventure Builder 1.01 from Debu Panda and had some build problems. Does anybody know if this demo was tested with the production version of 10.1.3? I used the standalone version and had to tweak
-
Folder with Question mark on it on a gray screen. Will not restart!? :(
While browsing online the other night, my Macbook completely froze up on me. I couldn't move my mouse and the screen froze. I decided to restart it but then the Macbook started making a whirring/ clack clack noise and I got a gray screen with a flas
-
Error 116 at Unflatten from string.....
Hi I want to save and load the control values of the tab pages I am getting the following error "Error 116 occurred at Unflatten From String Unflatten or byte stream read operation failed due to corrupt, unexpected, or truncated data." t
-
HT1349 how do I get all the music I have purchased on one computer
All my music has been purchased with the same credit card and I just want to get all my music on one computer. How do I do that?
-
Please help! These commands are essential to the way I work in Illustrator - probably for you too. Keyboard shortcut to Arrange Object - Send to Back, Bring to Front, etc. None of these commands will run. What am I doing wrong? I can drag the layers