Battery is not charged after using all of my battery. what's wrong? is it about charge machine or my computer?

battery is not charged after using all of my battery. what's wrong? is it about charge machine or my computer?

battery is not charged after using all of my battery.
Of course it isn't — you've just drained it. Plug your AC adapter in and charge it up again.

Similar Messages

  • Photos (Background Activity) using all of my battery

    I've had this problem for about a month where my Photos app is using 20% to 30% of my battery daily and 25% to 35% weekly with "Background Activity". I've contacted Apple Genuis twice about it and they have no clue what the problem is and I've sent full diagnostic tests in and still have no clue. I've restored my phone and always quit Photos app in multitasking even though I don't use it that much, I use other apps more than I use Photos but it still uses twice the battery as my main apps. I turned off most of my apps to have access to my photos and don't have iCloud Photo Share or Stream on. I can't find the Photos app in the background app refresh settings to turn off background activity so how do I stop it from using all of my battery? Please help!

    So my phone is having the exact same issue except my problem lies with Notes.
    This has literally happened since the 8.3 update a few days ago.  I'm on 2+ full charges a day on my iPhone 6 that used to last me 9-10 hours!!  I've been to the Genius Bar as well been on the phone with AppleCare & they have no clue.  I've done 2 full restores from my old backup with no change & diagnostics show the battery-life is at 100% with no faults.  It does show a steady drain however, and I've even wiped iCloud from my phone & added it as new!!
    Anyone have a solution!?!?  Literally about to throw my phone at a wall!

  • My ipod will not let me use all but like 3 apps fully without closing me out of the app. I have a 2nd generation ipod touch that has IOS 4. Why is this happening and should I take it to an apple store??

    My ipod will not let me use all but like 3 apps fully without closing me out of the app and i can only use safari or the app store for about 10 seconds without it shutting down the app. This has been happening for about 6 months after the upgrade to ios 4. Please help, should i take my ipod to an apple store?? It is a ipod 2nd generation itouch with ios 4.

    We won't know until you try the procedure.   The reset will not affect the content of the iPod.
    Stedman

  • Overhead calculation not happening after using Overhead key and orgin group

    overhead calculation not happening after using Overhead key and orgin group.
    There was a runtime error earlier related to u201Cdefine credit u201C IMG node under costing sheet component and we have applied SAP note 769946 and that error was gone out of the way
    We want to apply/add Overhead to SFG/FG materials.
    We are using PP order with PCC(product cost collector) as the cost object , i.e costing by period.(system ECC 6)
    But our problem is with material standard cost estimate process.
    We have assigned overhead keys to the percentage rates in costing sheet for material standard costing and assigned the origin groups to the credits of costing sheet. But after running the cost estimate overhead is not taking into account for standard cost calculation.
    In the define credit entry table key field is valid to date strangly and actually system should allow one than one entry with same valid to date and same sec.Cost element(type-41) for different cost centers.
    But if we without using overhead key and origin group, the entire cost in that supporting cost center will come to all materials (SFG/FG) and we can not distinguish between different product materials(SFG /FG).
    We have checked all things as mentined below.
    Firstly that the correct costing sheet is assigned to the valuation
    variant.
    That the costing sheet is entered for the appropriate material type:
    Finished and semi finished or material components.
    All of the above can be checked and verified via transaction OKKN.
    In addition make sure that the base value maintained is present in the
    costing, for example the base may include an Origin group, is that
    origin group part of the materials being costed?
    Similarly if the base is found and values exist how is the overhead
    rate of the costing sheet set up, is it valid etc.
    And finally do a similar check for the credit.
    we doubt this as a programm error...
    So, request all experts to have ur feedback..

    Dear,
    Check your origin group & material unit of mesaurement is same.
    some time in costing sheet origin group is maintain in different unit & for materail it's maitain in other unit of mesaurement.
    You can see unit of measure for material in Additional data - unit of measure.
    Check BOM component material unit also.
    Check same  unit of measure is maintain in KZS2
    I hope above will useful.
    GOPAN

  • Overhead calculation not happening after using orgin group.

    overhead calculation not happening after using orgin group.
    There was a runtime error earlier related to u201Cdefine credit u201C IMG node under costing sheet component and we have applied SAP note 769946 and that error was gone out of the way
    We want to apply/add Overhead to SFG/FG materials.
    We are using PP order with PCC(product cost collector) as the cost object , i.e costing by period.(system ECC 6)
    But our problem is with material standard cost estimate process.
    We have assigned overhead keys to the percentage rates in costing sheet for material standard costing and assigned the origin groups to the credits of costing sheet. But after running the cost estimate overhead is not taking into account for standard cost calculation.
    In the define credit entry table key field is valid to date strangly and actually system should allow one than one entry with same valid to date and same sec.Cost element(type-41) for different cost centers.
    But if we without using overhead key and origin group, the entire cost in that supporting cost center will come to all materials (SFG/FG) and we can not distinguish between different product materials(SFG /FG).
    We have checked all things as mentined below.
    Firstly that the correct costing sheet is assigned to the valuation
    variant.
    That the costing sheet is entered for the appropriate material type:
    Finished and semi finished or material components.
    All of the above can be checked and verified via transaction OKKN.
    In addition make sure that the base value maintained is present in the
    costing, for example the base may include an Origin group, is that
    origin group part of the materials being costed?
    Similarly if the base is found and values exist how is the overhead
    rate of the costing sheet set up, is it valid etc.
    And finally do a similar check for the credit.
    we doubt this as a programm error...
    So, request all experts to have ur feedback..

    Dear,
    Check your origin group & material unit of mesaurement is same.
    some time in costing sheet origin group is maintain in different unit & for materail it's maitain in other unit of mesaurement.
    You can see unit of measure for material in Additional data - unit of measure.
    Check BOM component material unit also.
    Check same  unit of measure is maintain in KZS2
    I hope above will useful.
    GOPAN

  • Battery #2 not present after windows 8.1 upgrade

    battery #2 not present after windows 8.1 upgrade. I am using sony vaio laptop model VPCZ2390X

     
    Hi aalmoeen, 
    Thank you for visiting Sony Community! 
    I assume your computer has an extended battery pack, right? Are you using a genuine Sony battery packs? Please follow these steps to isolate the issue: 
    Power Cycle
    Turn off the laptop -> push and hold the battery off button for 5 seconds located on the bottom of the laptop. (You may use safety pin). 
    Remove the battery pack and install it once again. Test the laptop again. 
    Remove the battery pack -> push the battery off button -> install the battery pack once again. 
    Reset BIOS
    Run Vaio update and Windows update. 
    Make sure you have the updated drivers and software, check on eSupport website. 
    For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
    Hope these steps help. 
    Thanks,
    Vincent 
    If my post answers your question, please mark it as "Accept as Solution"
     

  • SHCess field not appearing after using utilization tab in excise invoice

    Dear All,
    SHCess field not appearing after using utilization tab in excise invoice.The other fields and values releated to SHCess are appearing.
    Please give the inputs.
    Regards,
    deepti

    issue resolved

  • I misplaced my ipad, so I remotely erased it.  Then I found it, but now I cannot use all of the options in the settings.  I have restored from backup, but it still is not letting me use all functionality.  Help!

    I misplaced my ipad, so I remotely erased it.  Then I found it, but now I cannot use all of the options in the settings.  I have restored from backup, but it still is not letting me use all functionality.  Help!

    Would throwing it in Recovery mode and restoring as new clear it up?
    (same for Ipad)
    Step 1: Turn off the iPhone. To do this press and hold the power button till you see the “Slide to Power off” screen. Now slide the button to turn it off.
    In case your iPhone is stuck in an infinite loop and the previous option is unavailable, press and hold the Power and Home button till the screen goes off. Remember to leave both the buttons as soon as the screen goes off and before the Apple logo appears again.
    Step 2: Connect the iPhone’s USB cable to your computer but not to your iPhone yet.
    Step 3: Now hold down the Home button and while you are holding it connect the USB cable. Keep holding the Home button till you see the Connect to iTunes screen on your iPhone(Screenshot shown below). iTunes will show an alert saying a device in recovery mode has been detected.
    Here’s what your iPhone screen will look like once its in the iPhone Recovery Mode.
    Read more: http://www.callingallgeeks.org/15018/how-to-put-iphone-or-ipod-touch-into-recove ry-mode/#ixzz296y04ygX
    Under Creative Commons License: Attribution No Derivatives
    THEN RESTORE THE DEVICE AND SETUP AS NEW. JUST YOU WILL HAVE TO DOWNLOAD YOUR APPS AGAIN(FREE) ETC....
    LEAST THE SECURITY WORKS HAHA!!! I also wouldnt get upset, be thankful you found it.

  • Thumbnails do not display after using rebuild tool

    I am using OSX 10.7.5, and iPhoto 8.1.2.
    recently I made a back up copy of my files.
    I then reinstalled my operating system.
    I then copied my iphoto library back onto my computer.
    imported my iPhoto library into iPhoto
    Pictures are in iPhoto.
    Thumbnails do not display.
    I have used the rebuild tools provided by iPhoto.
    Still no thumbnails displaying.
    any other ideas?

    It relates to your suggestion in that, the reason I posted was to solve a thumbnail issue.
    "re: Thumbnails do not display after using rebuild tool"
    Terence suggested reloading my back up library.
    I asked Terence where I should import to.
    I was thinking that my thumbnail issue was related to the way I imported my back up.
    You clarified where to import the library...
    I tried it and I still have no thumbnails
    I have already tried repairing permissions and rebuilding thumbnails using the i photo repair tool.
    can you help me?

  • Mail not working after using migration assistant - what am I missing?

    Mail not working after using migration assistant - what am I missing?

    The mailbox list is divided into categories with headings in caps, such as ON MY MAC. When you hover the cursor over one of those headings (except for MAILBOXES), you should see the word Show or Hide on the right. Click Show. The  MAILBOXES category can't be hidden.
    In each category, the mailboxes are arranged in groups, such as Inbox. To the left of each group is a small disclosure triangle. If the triangle points to the right, click it so that it points down.

  • Iphone says messages is taking up 6GB of storage, even after I deleted all my messages. What is wrong?

    iphone says messages is taking up 6GB of storage, even after I deleted all my messages. What is wrong? This is preventing me from downloading the most recent iOS, not to mention numerous other things.  Thanks for any help! I am at a loss of what to do.

    For that much storage being taken up the only thing that can be done as of now is back the device up in iTunes and restore the iphone.  The restore will also update the phone.

  • I used to able to watch movies, TV series on youtube for more than 20 minute straight. In last few days, somehow it stopped after only 1-2 minutes. What is wrong with my iPhone 4S? I even updated youtube.

    I used to able to watch movies, TV series on youtube for more than 20 minute straight. In last few days, somehow it stopped after only 1-2 minutes. What is wrong with my iPhone 4S? I even updated youtube.

    That would indicate an issue with the local network, not internet. This can impact devices differently and will likely be more obvious on a streaming only device.
    If you are on wifi try ethernet
    Make sure DNS is set to auto (settings - general - network)
    Go to istumbler, netstumbler or similar to get a report of the network, look for signal strength and noise.

  • When i log in my apple id in itunes a message prompt me "This Apple ID has not yet been used with the itunes store" what do i need to do?

    when i log in my apple id in itunes a message prompt me "This Apple ID has not yet been used with the itunes store" what do i need to do?

    If you can log into the computer, go to the Mac App Store and purchase Mavericks under your AppleID.   Even though its free, they still consider it a purchase.
    If you are not able to log into your Mac you can try on a different Mac.  Once you purchase it, you can stop the download if you want.
    Once you do that then you should be able to reinstall via the Recovery HD

  • When I try to install Adobe Acrobat XI Pro, I get an error message, "Key not valid for use in specified state".  What is this?

    When I try to install Adobe Acrobat XI Pro, I get an error message, "Key not valid for use in specified state".  What is this?

    See if this post by turingtest2 fixes it : key not valid for use in specified state

  • A prompt that says "Could not use the clone stamp because the are to clone has not been defined (option-click to define a source point), appears EVERY time I try to use the clone stamp. What is wrong and how can I fix this

    A prompt that says "Could not use the clone stamp because the are to clone has not been defined (option-click to define a source point), appears EVERY time I try to use the clone stamp. What is wrong and how can I fix this?

    If a tool is acting up, one suggestion is to reset the tool.
    Ctrl-click on the clone tool icon in the Options bar and select Reset Tool.

Maybe you are looking for