Battery is not charging after once full discharge
hi,
I have Z60m 2530-A58 which is not charging it says: battery error has occured replace the battery , after once it was fully discharge to 0% but my notebook was only 1.5 year old what problem has occured can anyone suggest me pls......................
pls help i am using ubuntu 8.10 and windows xp both
Ok, I assume motherboard is aged or damaged somehow. Maybe it has been on plug for four or five years. It is late 2006's model.
First of all, I was be able to see it charging while it was connected to the MagSafe Power Adapter 85w then I close the lid and put it aside on the end table. I did not touch it for a few days. The white led was on in first few days then it become dim and fade out. I was puzzled and looked at the MagSafe Power Adapter connector on the MacBook Pro. It shows green led, which is still on power.
Secondly, I decided to open it and nothing happens then pressed the power button. It will boot up and open from the beginning. It did not hibernate or showing as resume after shutdown. I looked at the bottom of MacBook Pro's battery area. I press the small button to see how much battery left. It was on dead zero. This is why I called it drained out power.
Thirdly, I decided to check the Apple website to see what's wrong with it. Most of the forums said that SMC needs to be reseted since I could see the X mark on the battery icon. After I reseted the SMC, I could see the "Battery is not charging".
If I unplugged the connector, it will lose the power and shut down immediately without being shutdown properly.
Hmm?
Similar Messages
-
battery is not charged after using all of my battery. what's wrong? is it about charge machine or my computer?
battery is not charged after using all of my battery.
Of course it isn't — you've just drained it. Plug your AC adapter in and charge it up again. -
My battery is not charging(blinking orange) after once full discharge and shutdown
one day, i have forgotton the battery doesn't have enough charging and i have opened my X61.
after recovery from hibernate, i saw the power had only 0%.
then it shudown before i try to hibernate it again.
almost half month after, today i found the battery is not charging and keep blinking orange.
the power manager show this message.
"Irreparable damage to the battery has been detected. replace the battery with a new one"
my battery is manufactured by Sony but not on the list of "battery recall"
i bought it for about 1 yr 3 mths only and my battery has only 15 cyclecount...
is there any way to get the battery recovery again??
THANKS!!!
Message Edited by abchau on 01-15-2009 08:07 PM
Message Edited by abchau on 01-15-2009 09:05 PMHow long was it off charge to drop from 5149 to 1054 mAh on the battery?
If not actually doing anything looks like a good reason to visit an Apple Retail store genius bar and have it checked. -
Battery does not charge after rescue & recovery
Hi,
Yesterday I set up my computer fresh from the preload on the harddrive due to slowness, instabilities, inability to use VPN etc. After the reinstallation of OS and securiy updates, my battery does not charge anymore. The battery indicator on the front panel keeps blinking, and the Lenovo message center reports that irrepairable damage has been done to the battery and that it must be replaced.
My battery is not among the recalls by Lenovo.
Any idea if there's any option but buying a new battery? It just does not seem right that the battery is unusable after new OS setup.
Cheers, Thorbjorn
T400s | 2808-CYG | SSD | 4GB RAM | Windows7 Prof. 32bit
Solved!
Go to Solution.tbar2112, welcome to the forum,
you should check out this site if you haven't already done so.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog -
Macbook 4,1
Early 2008 15" macbook pro
Running Snow Leopard
the Battery was not working after only 23 cycles
I tried the Battery update and now it will not boot at all
I really do not want to loose my data on the drive
panic message is
Unable to find driver for this platform: "ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Please helpPanic Message
panic(cpu 0 caller 0x000x563ebd) : Unable to find driver for this platform:
"ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Debugger called: <panic>
Backtrace (CPU 0), Format - Frame : Return Address (4 potential args on stack)
(7 lines of hex)
BSD Process name corresponding to current thread: Unkonwn
Kernel version:
Darwin Kernel Version 10.8.0" todays date ; root:xnu-1504.15.3~1/release_I386
I tried to boot from CD can, but i dont want to loose any information.
Tried disk tools
Hardware test
Tried to check if it was memory sticks failing or battery , nothing else plugged in
if i boot holding Apple key and S
I get additional warnings about AppleACPIPlatform and not being able to load Kext -
Battery is not charging after buying new charger for Qosmio X300
Hello all
My problem started when the charger of my laptop toshiba qosmio x300-130 made a strange noise and stoped working . laptop stayed on and was working perfectly as the battery was full .
I cloused pc and opened again next day to check my mails and then cloused it again .
the charger was off so i ordered one new charger from the company that support toshiba laptops in greece .
After 5 days i received the new charger from theyr offices . run home and pluged it but something was wrong . the battery isnt charging ! windows giving me message that battery exists but not charging !
The battery light of the computer lights up when i put the power on but after few seconds start blink and then it go off .
Also when i operate pc with battery on it it start making the noice that battery is low and then it turns off even that it is on power with the charger .
I went back to the company and they tald me that the charger is fine and that the battery just died couse it was her time to die !!! any one can help me ?> I went back to the company and they tald me that the charger is fine and that the battery just died couse it was her time to die !!!
Well, can you use the notebook without the battery but only in connection with the AC adaptor?
If yes, then the AC adaptor is OK and fully compatible.
The Ac Adaptor should support the 19V and 9,5A
The Ampere (A) value could be a little bit different. This is no matter but the Volt (V) value has to be the same 19V
In your case the battery could be faulty or there is some problem with power supply electronic on the motherboard.
But I think the battery should be checked firstly -
Mid 2010 Macbook Pro battery will not charge after plugging in firewire cable shut down computer
I have a mid 2010 15" Macbook pro with Lion installed.
I was running off battery, and I went to plug in a firewire cable, not plugged into anything, and when I inserted it, the computer shut off.
The computer would not turn on again without being plugged into the AC adaptor. The magsafe charger shows green, but the computer says not charging. The battery is showing 57%, but the indicator lights will only light up when AC charger is connected..
I have let it sit off, and plugged in for a couple hours, and nothing chages, and let it sit overnight not plugged in, but nothing.
I have read other forums about the same issue,, it seems like its a common issue, and some have said what it could be, but no one said what it IS.
I have tried resetting the SMC and PRAM, but to no avail.
When i plug in the AC adaptor, the computer immediately turns on (which I find kond of funny), and I am able to turn it off normally, and it will stay off, and I can also turn it on if the charger has been connected from pervious.
Below is my power information.:
Battery Information:
Model Information:
Serial Number: W0013PVDXBX0A
Manufacturer: SMP
Device Name: bq20z451
Pack Lot Code: 0
PCB Lot Code: 0
Firmware Version: 201
Hardware Revision: 000a
Cell Revision: 157
Charge Information:
Charge Remaining (mAh): 3406
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 5956
Health Information:
Cycle Count: 395
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 11638
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 5
Wake on AC Change: No
Wake on Clamshell Open: Yes
Wake on LAN: Yes
Current Power Source: Yes
Display Sleep Uses Dim: Yes
PrioritizeNetworkReachabilityOverSleep: 0
RestartAfterKernelPanic: 157680000
Battery Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 3
Wake on AC Change: No
Wake on Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
RestartAfterKernelPanic: 157680000
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0100
Wattage (W): 85
Revision: 0x0000
Family: 0x00ba
Serial Number: 0x00b9468c
Charging: No
Any help would be greatly appreciated. Thanks everyone.I have a mid 2010 15" Macbook pro with Lion installed.
I was running off battery, and I went to plug in a firewire cable, not plugged into anything, and when I inserted it, the computer shut off.
The computer would not turn on again without being plugged into the AC adaptor. The magsafe charger shows green, but the computer says not charging. The battery is showing 57%, but the indicator lights will only light up when AC charger is connected..
I have let it sit off, and plugged in for a couple hours, and nothing chages, and let it sit overnight not plugged in, but nothing.
I have read other forums about the same issue,, it seems like its a common issue, and some have said what it could be, but no one said what it IS.
I have tried resetting the SMC and PRAM, but to no avail.
When i plug in the AC adaptor, the computer immediately turns on (which I find kond of funny), and I am able to turn it off normally, and it will stay off, and I can also turn it on if the charger has been connected from pervious.
Below is my power information.:
Battery Information:
Model Information:
Serial Number: W0013PVDXBX0A
Manufacturer: SMP
Device Name: bq20z451
Pack Lot Code: 0
PCB Lot Code: 0
Firmware Version: 201
Hardware Revision: 000a
Cell Revision: 157
Charge Information:
Charge Remaining (mAh): 3406
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 5956
Health Information:
Cycle Count: 395
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 11638
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 5
Wake on AC Change: No
Wake on Clamshell Open: Yes
Wake on LAN: Yes
Current Power Source: Yes
Display Sleep Uses Dim: Yes
PrioritizeNetworkReachabilityOverSleep: 0
RestartAfterKernelPanic: 157680000
Battery Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 3
Wake on AC Change: No
Wake on Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
RestartAfterKernelPanic: 157680000
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0100
Wattage (W): 85
Revision: 0x0000
Family: 0x00ba
Serial Number: 0x00b9468c
Charging: No
Any help would be greatly appreciated. Thanks everyone. -
Satellite L500-14X - Battery does not charge after upgrade to Win 8
HI,
after upgrating my laptop to Win 8 the battery stops charging...
the message says..."pluged but not charging"....
Any suggestion........exept to reinstall win7...??Hi
Usually there is no big difference between the Win 7 and Win 8 so I really dont understand why this battery issue should be related to Win 8.
In my opinion its not Win 8 problem and I think even if you would install Win 7, this issue would not be solved
Try this:
Disconnect the AC adaptor and remove the battery
Now leave the notebook disconnected for a longer period of time (10 hours)
Then press and hold power button 30 sec long and then connect both parts.
The Ac adaptor should be connected for a longer period of time to allow the system to pre-charge the Battery -
My battery is not charging after resetting my SMC
So my fan started going all crazy like so I resetted my SMC but now my computer charge will be off and on. Like it worked just a few mintues ago but when I got up my computer restarted itself and my fans went all crazy like again. So I restarted the SMC once again but that one didn't last long until my fans acted up.
Model Information:
Serial Number: W004659DFD3LA
Manufacturer: SMP
Device Name: bq20z451
Pack Lot Code: 0
PCB Lot Code: 0
Firmware Version: 201
Hardware Revision: 000a
Cell Revision: 165
Charge Information:
Charge Remaining (mAh): 1054
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 5149
Health Information:
Cycle Count: 91
Condition: Normal
Battery Installed: Yes
Amperage (mA): -887
Voltage (mV): 11123
Thats my battery information as of right now and I'm contemplating on going to a mac store to just take it in to see what the problem is, only problem is the closes one is about an hours drive :/How long was it off charge to drop from 5149 to 1054 mAh on the battery?
If not actually doing anything looks like a good reason to visit an Apple Retail store genius bar and have it checked. -
Why can't I turn on my iPhone 3Gs after a full discharge?
My phone recently discharged until shutoff. When I tried to charge the phone, I got the red battery charge indicator and a possitive charge symbol right below that, furthermore, my phone did not respond to any actions such as holding down the power button, home button, or both simultaneously. Nothing.
On a good note, I tried a new cord and was able to plug the phone into my laptop but didn't get the driver function chime for an active connection to the PC. Following the failure of my computer to recognize the device, I tried again to hold the power button for fifteen seconds while iTunes was running (not that that did anything) and the phone plugged in to the PC via USB cable yet unrecognized.
The phone powered on showing me the apple logo at 4% battery life then immediately gave me a warning that the battery was less than 20%.
WHEW!
I am guessing that the phone has some mechanism that will disallow the phone from being powered on following a charge after a full discharge. I'm not letting my battery get below 20% again.I am guessing that the phone has some mechanism that will disallow the phone from being powered on following a charge after a full discharge. I'm not letting my battery get below 20% again.
Good guess but bad idea. It's NORMAL for the phone to be unresponsive, just showing the red icon for up to 30 minutes of charging, when it had been run to shut down. This prevents the battery from being used repeatedly in a near depleted state which can damage overall battery life.
You SHOULD run the battery to shutoff periodically to maintain meter calibration. -
Battery Not Charging after 10.6.8 Update (Macbook Pro 13' i5 2011)
Hi,
I own a 4 months old Macbook Pro 13in with i5 processor. I was using it normally until yesterday, when a software update prompting for enhancements on thunderbolt drivers and some stuff regarding OS X Lion was displayed. I started the software update, let the macbook plugged in and went to sleep.
Today I found out that my battery is not charging anymore (when plugged in, the magsafe led lights green and the energy saver displays Not Charging). I've already tried to restart SMC to no result(unplugged, waited for 15 sec, plugged again and after 5 sec turned it on).
Basically, my macbook is now useless. I use it mainly in the college, cant have it always plugged in and my second half classes start tomorrow!
I dont have a time machine backup.
I dont want to open the macbook since its still under warranty. What should I do?
The system profiler info can be found below:
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro8,1
Processor Name: Intel Core i5
Processor Speed: 2.3 GHz
Number of Processors: 1
Total Number of Cores: 2
L2 Cache (per Core): 256 KB
L3 Cache: 3 MB
Memory: 4 GB
Boot ROM Version: MBP81.0047.B0E
SMC Version (system): 1.68f96
Serial Number (system): C02FFNFLDH2G
Hardware UUID: 5C7658AB-7D4A-5731-A54F-8FC8ABCDA88C
Sudden Motion Sensor:
State: Enabled
Power On Self-Test:
Last Run: 7/31/11 3:01 PM
Result: Passed
Battery Information:
Model Information:
Serial Number: W010858B9D3BA
Manufacturer: SMP
Device Name: bq20z451
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0201
Hardware Revision: 000a
Cell Revision: 0158
Charge Information:
Charge Remaining (mAh): 131
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 5542
Health Information:
Cycle Count: 33
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 10987
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 30
Wake on AC Change: No
Wake on Clamshell Open: Yes
Wake on LAN: Yes
Current Power Source: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 30
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 15
Wake on AC Change: No
Wake on Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0100
Wattage (W): 60
Revision: 0x0000
Family: 0x00ba
Serial Number: 0x00130284
Charging: NoDid you follow these steps, EXACTLY?
http://support.apple.com/kb/ht3964
Note: Learn about removing the battery on MacBook and MacBook Pro.
Shut down the computer.
Disconnect the MagSafe power adapter from the computer, if it's connected.
Remove the battery.
Press and hold the power button for 5 seconds.
Release the power button.
Reconnect the battery and MagSafe power adapter.
Press the power button to turn on the computer. -
Any ideas on how to fix ipad after the new iOS 7 update? My battery will not charge, my ipad is hot to the touch, the iTunes Store won't open, and my messages on Facebook aren't showing up when I chat and pintrest won't pin to my boards.
If you have all your music on the cmputer then i would connect up my phone uncheck the Sync Music option and apply.
This should take all the music off your phone .Then you can resync the music back on to it.
If this doesn't work maybe a restore to factory settings and start from scratch is the way to go -
Macbook Pro battery is not charging but the battery meter is full
Hi guys!
I have a 19 months macbook pro. I've tried using 2 different AC adapter but my mac's battery is still at 0% and the status says "Battery is not charging". I think my battery is dead but the LED battery indicator on my battery shows 5 lights, means its at full power.
I've tried to disconnect the AC cable and remove the battery, then press the power button for 10 sec but nothing change when i start my mac again...i also tried to reset my PRAM ( i think ) by holding a cmdopt+PR while rebooting but it didn't help to solve the problem too. I also have the battery update 1.2 installed on my mac and the results is still the same.
This is my battery info from system profiler. I hope someone can tell me what to do before I visit the Apple store.
Battery Information:
Model Information:
Serial Number: SMP-ASMB014-3658-b12
Manufacturer: SMP
Device name: ASMB014
Pack Lot Code: 0001
PCB Lot Code: 0000
Firmware Version: 0102
Hardware Revision: 0202
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 0
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 0
Health Information:
Cycle count: 298
Condition: Check battery
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 12528
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 15
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: NoHello,
I am having some strange battery behavior. I bought a FastMac TruePower Battery that is supposed to have extended capacity. Now when the battery dies, i plug in my MagSafe to charge it and it immediately says 'not charging', but then begins to charge. It either continues to charge and gets stuck at 80% or so and reads "calculating" in the menu bar, or just jumps between 'charging' and 'not charging'. The symptoms are very strange, and FastMac already sent this battery back saying it passes all of their tests. I do not want to send it back again because they charged me to send it back to myself even though it still does not work as advertised. I have my original Macbook Pro Apple battery which still charges fine, so i assume it is a problem with the battery based on a simple process of elimination.
Battery Information:
Model Information:
Serial Number: BIT-ASMB012-***-* <Edited by Moderator>
Manufacturer: BIT
Device name: ASMB012
Pack Lot Code: 012d
PCB Lot Code: 050d
Firmware Version: 647e
Hardware Revision: 2700
Cell Revision: 0000
Charge Information:
Charge remaining (mAh): 2116
Fully charged: No
Charging: No
Full charge capacity (mAh): 5029
Health Information:
Cycle count: 24
Condition: Good
Battery Installed: Yes
Amperage (mA): 2628
Voltage (mV): 11962 -
After update battery drained, not charging
updated to 2.0 / battery was fully charged
after a day turned off battery is 0% and not charging.Was it turned off or just on standby?
-
Battery not charging after upgrade to 10.4.9
Ever since I did the last system update, my battery is not charging.
My light is yellow, and the indicator in the menu bar states that I am connected to AC.
The charger is warm, the battery is cool to the touch, and has a single indicator light illuminated.
This is the original battery, but has always charged (albeit, it only lasted about 20 minutes).
I suspect that the system upgrade may be a factor.
Any thoughts?
Thanks,
BorisNewerTech's batteries offer the highest capacity and thus the longest working time on a charge. You pay a premium for the extra oomph.
I haven't seen any preponderance of enthusiastic messages posted here about any particular brand or vendor. You certainly don't need to spend $120; new Tibook batteries are advertised as low as $80-90 by some vendors. I've never bought from any of the following, but they may be worth a look or call:
http://www.expercom.com/productdetail.html?PRODUCTID=295232
http://www.atbatt.com/product/5675.asp
http://www.academicsuperstore.com/market/marketdisp.html?PartNo=759446
Price comparison site:
http://www.nextag.com/apple-titanium-g4-powerbook-battery/search-html
For other options, Google "Powerbook G4 Titanium battery".
Maybe you are looking for
-
RE: Putting a song into my iweb page, following Mike Wong's instructions with considerable and valuable help along the way from James Tseng. I have spent all day working at this and failing countless times. I finally got to the point where I was supp
-
My HP photosmart premium with wireless ePrint, will not print files from mobile phone says it **may have** a virus- and deletes the file?!? My Fiance has the same phone, and I used it. It completed the file??? If I text message and E-mail address, my
-
Itemcost column table at warehouse level in item master
I have an issues regarding the item cost in Item master --> Inventory Data tab when we select Valuation method either Standard or Moving average we can see the itemcost (Column) value at warehouse level but for FIFO method we cant see the itemcost co
-
Personal Layout not working in IE
Hello, After I create a personnal page layout with Developper Studio, the layout is properly displayed on the page creation view so that I can put my iviews. But the page is not well displayed in IE. In chrome it looks fine (even if other parts of th
-
IPhone 4S speaker chooses not to function
Basically I dropped my iPhone 4S in water and immediately took i tout again (within 2 seconds) but it took a bit of water damage. There were a couple of issues but only one remains after drying out - the speaker. When I used it immediately after drop