Battery issue after iOS upgrade to 4.1
I have upgraded my iOS to release 4.1. After that my battery will be empty within a 4 or 5 hours. before the upgrade the battery works more than a day.
Another issue is to delete emails. If I delete some mails and wait a few seconds the mail will be received again. This happens with my Mobile Me account AND for my exchange account. Before the upgrade was made all works properly.
I have tried to reset the iPhone to factory settings and make a new configuration manually but the result is still the same.
Anyone has an idea what kind of issue I have?
1 & 2, common problems.
3 - check your settings
Apple fix the bugs? Sooner or later.
Good luck.
<Edited by Host>
Similar Messages
-
POE 3560 Issue after IOS upgrade
Hello,
I having issue where 6 WLAN AP's not coming back uo after reboot and IOS upgrade of 3560 POE swtiches - . Prior to changes here most if not all ALL the 23 Aps were mainly on one switch, Now after these changes they are now spread over three switches ( 3560's) - with 17 coming back on line
I am sure its not the power limitation of the switch(s) as the one switch I am TS at present had a fairly large allocation of the aps attached prior to ios upgrade and reload. and the available power value now showing is applicable.for 8 AP's
I have tried various TS steps to try and bring them back up - A couple of things I would like to try but I am restricted to do so is to check the APS physically or downgrade the ios!
Any input on this matter would be truly appreciated.- (attached is the log buffer debug)
res
Paulc3560-ipbase-mz.122-25.SEE2.bin
You upgraded the IOS to the switch? I shudder at the thought of what old version did you upgrade FROM.
Available:370.0(w) Used:110.4(w) Remaining:259.6(w)
You've got more than enough PoE left.
Only two things comes to my mind:
1. Cable issue - Unfortunately, the 3560 is a non-GigabitEthernet and this particular sub-model does NOT support TDR.
2. Hardware failure - Read THIS. -
IPod touch 3rd generation battery issue after iOS5 upgrade
Post upgrading the iPod Touch to iOS5, I have been facing severe battery issues. Is there a way this can be rectified? Alternatively can I undo my upgrade of iOS?
Please help!!!unfortunately idevice does not suport downgrade you will ave to wait for a fix
-
Battery issues after Mavericks upgrade
After upgrading to Mavericks I got Service Battery error (at just 99 cycles) and my battery life dropped to about half (in actual time).
Is that a known issue? What should I doTry a SMC reset:
http://support.apple.com/kb/HT3964
If no change, make an appointment at an Apple store genius bar for a FREE evaluation.
Ciao. -
Battery Issues after Lion Upgrade
Anyone else experiencing issues with battery after upgrade?? Battery now failing when fulling charge about 10 mins after removing power cord. Also saying Service Battery. Had no issues with Snow Leopard and also my 15" MBpro is only about 1.5 yrs old...
Same problem. Recently upgraded to Lion. Was using my Mac fine (running off battery) this morning, no worries. Came home from work, wouldn't turn on without plugging it in, turned it on, said "service battery", left it charging for awhile, unplugged it, it wouldn't turn on again without plugging it in, told me 0% charge. How can it go from working fine in the morning to not at all at night??
Have had a few problems since Lion. Wish I hadn't upgraded. Also had my itunes account hacked last week. Losing my love for apple -
I bought a Sandisk Connect Media Drive, downloaded the app from iTunes. Before iOS 8, movies played fine. After iOS upgrade I can no longer play movies downloaded from iTunes to the media drive. Anyone else have a similar issue?
I checked with SanDisk's own online support and they indicate that they have notified Apple of the issue.
According to SanDisk, the problem lies with Apple not having the iOS 8 version of the Safari browser having DRM decoding enabled that the Media Drive relies upon to decode and play iTunes DRM titles. Non DRM encoded videos will play in the browser.
DRM audio is not effected as this is handled by the native iOS music app.
As of the date of this post SanDisk have not been given a timeframe by Apple for this issue to be resolved.
I hope that Apple resolves this issue quickly as I have a large collection of DRM video titles on a 128Mb memory card installed in the Media Drive that I am unable to view. -
Iphone 4s battery melts after ios 7.1
Last Friday I've upgraded to IOS 7.1. especially after learning that the upgrade is especially helpful for iphone 4s,
Yes it fastens the device but the battery "melts"
I've searched the issue from the web and applied all the suggestions to improve battery life after ios 7.1.
If I don't use internet facilities (even wi-fi) its OK, no problem,
But from the moment I begin to use wi-fi or cellular its like a count down 95-94-93-92...., feel really bad about it,
Now I just use it as a "phone" not a smart phone,
If a want to use it as a "smart phone" it is no longer a mobile- I shoul use it with battery charger,
Hope a fix will come as soon as possible,Close all open apps by double-tapping the home button, then swiping up and off the screen with the app window (not the smaller icon).
Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. (No data loss)
If this doesn't help, back up and restore via iTunes. If the problem continues, restore as a new device and test. If the problem is solved, there is some kind of corruption in your backup file or maybe it's one of your apps causing problems. If it continues, take it to an Apple Store for evaluation of a possible hardware problem. -
3G icon in the status bar got disappear after ios upgrade 8.1
3G icon in the status bar got disappear after ios upgrade 8.1
Nginear48 wrote:
Thanks for your quick response. I've tried everything you suggested and get only temporary fixes. Sometimes for a day or two, sometimes only until I use Safari for the first time. It's annoying and probably effects battery life between charges.
You would think that it must have some effect on the battery, but oddly enough, the update to iOS 8 actually helped my battery life, in spite of all of these hinky little issues that are taking place. In my experience, the activity icon is not affecting the battery in a negative way.
Another issue with IOS 8.1 that you may have seen is the loss of icon pictures on home pages. Again it seems to be Safari related, since app icons found in the App Store are not affected, only web based icons you personally put on home pages. I get what I call a test screen similar to what you used to get on old tv sets on every one of my personal icons.
I know exactly what you mean. I got that as well. On a few of them, when I opened the websites using the generic test screen icons and then closed them, they changed back to the way that they should look. For the ones that did not change, I recreated the home screen shortcuts and deleted the generic looking ones - the test screen icons.
And don't get me started on iBooks.
For the very limited use that I make of the iBooks app, i haven't noticed any problems, but I rarely use the app. I don't read books on the iPad other than a few user guides and if they are pdf guides, they reside in more reliable and feature rich pdf apps on my iOS device.
I wish that I had the fix for the spinning activity icon, but everything that I try, is temporary at best. IMO, this is the buggiest iOS update that I have seen, and I have been using iOS devices since iOS 3 on my first iPad. I realize that there are plenty of people that are not experiencing issues, but I have seen a number of weird things that I wish I could fix. None of my problems are major, but they are annoying. -
No battery life after system upgrade
I've searched this forum and found a few notes about significant battery problems after Android upgrades. Immediately after upgrading my Droid X, my battery life went from more than 24 hours to about 4 hours. The battery is very hot and takes about 6 hours to charge. Clearly something is draining the battery. The Verizon tech folks declared it a faulty battery and are sending a new one. I am certain that's not the problem, especially since others have reported the same issue.
So I hoped to wipe the cache before having to do a factory reset -- it was suggested as a possible solution. I have found some instructions for wiping the cache, but I can't seem to get the instructions to work. I power off my Droid, then hold the home key. Nothing happens. So I can't get to the menu that gives the options mentioned. Can anyone help? I loved my Droid until this update... I really need my phone to work as I am self-employed. I am my own IT department!Hi dazzie,
I understand your discontent; I would be frustrated if my phone's battery drained for no apparent reason. Please run your phone in Safe Mode as recommended by Cody21 (thank you!). Safe Mode temporarily disables all applications that have been installed via the Android Market. Performing this troubleshooting step is necessary to determine whether a 3rd party application is the cause of an Operating System / Application issue.
I have checked my resources and I learned that similar battery issues have occurred with other devices upon a software upgrade due to third party applications that are not fully compatible with the upgrade Operating System and a Factory Reset has resolved most post upgrade issues. Please do a Factory Reset as this may resolve your concerns.
Please keep in mind that performing a hard reset will remove ALL data including the Google account, system data, application data, application settings, and downloaded applications. -
No valid license found after IOS upgrade on C3750x switch
HI,
Two switches below are working fine as a stack with IOS c3750e-universalk9-mz.122-55.SE5.bin & ipbase license.
Switch#1 (Master, WS-C3750X-24P-S)
Switch#2 (Member, WS-C3750X-24P-S)
After IOS Upgrade to c3750e-universalk9-mz.150-2.SE7.bin, The stack was broken. Switch#2 didn’t recognise valid ipbase license with new IOS and came up with lanbase license instead. Therefore stack cannot be composed due to license mismatch between Switch#1 (ipbase) and switch#2(lanbase).
I’m wondering why Switch#2 didn’t recognise ipbase license with new IOS even though IPASE is running well with previous IOS.
Here is excerpt from “show version” with 15.x image on Switch#2.
License Level: lanbase
License Type: Default. No valid license found.
Next reload license Level: lanbase
Here is excerpt from “show version” with 12.x image on Switch Stack.
License Level: ipbase
License Type: Permanent
Next reload license Level: ipbase
Thanks
JeongThanks guys,
I have fixed the issue by configuring 'license boot level ipbase' on the member switch#2. The switch recognised IPBASE license well and joined the stack successfully. -
Battery drain after yosemite upgrade
Can somebody solve my issue of battery drain after installing yosemite on my mac book air? battery used to last twice longer on the older OS
have done a entre check as below
Problem description:
Battery drain after Yosemite upgrade on mac book air 11”
EtreCheck version: 2.0.11 (98)
Report generated 24 November 2014 5:36:32 pm IST
Hardware Information: ℹ️
MacBook Air (11-inch, Mid 2013) (Verified)
MacBook Air - model: MacBookAir6,1
1 1.3 GHz Intel Core i5 CPU: 2-core
4 GB RAM Not upgradeable
BANK 0/DIMM0
2 GB DDR3 1600 MHz ok
BANK 1/DIMM0
2 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en0: 802.11 a/b/g/n/ac
Video Information: ℹ️
Intel HD Graphics 5000 -
Color LCD 1366 x 768
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:56:56
Disk Information: ℹ️
APPLE SSD TS0128F disk0 : (121.33 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / [Startup]: 120.47 GB (78.59 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
USB Information: ℹ️
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Startup Items: ℹ️
HWNetMgr: Path: /Library/StartupItems/HWNetMgr
HWPortDetect: Path: /Library/StartupItems/HWPortDetect
MobileBrServ: Path: /Library/StartupItems/MobileBrServ
StartOuc: Path: /Library/StartupItems/StartOuc
Startup items are obsolete and will not work in future versions of OS X
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 15.0.0.223 - SDK 10.6 Support
Flash Player: Version: 15.0.0.223 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
Default Browser: Version: 600 - SDK 10.10
3rd Party Preference Panes: ℹ️
Flash Player Support
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
4% WindowServer
1% fontd
0% sysmond
0% AppleSpell
0% notifyd
Top Processes by Memory: ℹ️
168 MB com.apple.WebKit.WebContent
168 MB Mail
137 MB softwareupdated
73 MB Safari
64 MB mds_stores
Virtual Memory Information: ℹ️
440 MB Free RAM
1.78 GB Active RAM
1.47 GB Inactive RAM
608 MB Wired RAM
1.07 GB Page-ins
213 KB Page-outs -
BT email not working. Cannot send emails from btconnect SMTP after iOS upgrade. This is the only difference I am aware of. Apple iPad 3. Can anyone help me please.
All resolved at last
Deleted the SMTP setting
Recreated the SMTP using the same settings
Able to send emails now
No logic - as usual - just a bug! -
Iphone 5 issues after IOS 8.2 update: all the iphones in the house receive the same phone calls ONLY while we are at home. Any ideas on how to fix this?
That is a new "feature" described in Connect your iPhone, iPad, and iPod touch using Continuity
You can turn it off by going to Settings > FaceTime and changing "iPhone Cellular Calls" to off -
PAD Mini Locked after iOS upgrade, tried reset on iPAD did not work, plugged in and device not appearing in iTUNEs for reset/restore. Just get an Apple Logo then a flashing blue screen as if it is caught booting up. This has happened twice before and iTunes restore fixed it. But this time device not appearing in iTunes.
Running iTunes for PC. But as stated restore has worked before! Any help greatly appreciated!!Place the device in DFU mode and let iTunes restore the device to factory condition.
-
Performance Issues after an Upgrade
Hello!
We are experiencing performance issues after we upgraded to a new version of Hyperion (11.1.2.1). At this point, I am not too sure about the actual causes for this degrade in performance but I am trying to narrow down the causes and need your inputs. Please help me with your ideas.
1) What could be the causes/factors for the performance to degrade after an upgrade?
2) Does the performance of a script depend on the user credentials i.e. who is launching the script? Whether it’s the super admin of the application/application owner or an application specific admin?
3) Does the performance of the scripts depend on the place you are launching it from? For example - will the performance differ if it’s launched from MaxL Vs EAS?
Please let me know your thoughts on this.
Thanks,
- KrrishThere are a number of bugs 12600557, 12675485, 12669814, 12698488 logged in for 11.1.2.1 - If you use Internet Explorer 8 and have data forms designed to use a large number of sparse dimension members in rows or columns, you may experience performance degradation when opening the data forms.
This has been fixed in Oracle Hyperion Planning, Fusion Edition Release 11.1.2.1 Patch Set Update (PSU): 11.1.2.1.101 which is available on My Oracle Support as Patch 12666861.
HTH-
Jasmine.
Maybe you are looking for
-
What is the best way to organise remote collaborative editing with Premiere Pro CC
I am writing to enquire about a solution for a collaborative project between two filmmakers in different countries. Ideally, we would be able to have a cloud media library that could be referenced by both of us as well as a project folder with work
-
Function REUSE_ALV_GRID_DISPLAY
Hi ! I wanted to ask few questions concern a standard sap ALV report created by the function REUSE_ALV_GRID_DISPLAY : 1. How to make columns editable, and to enable the user to change values of the columns ? 2. How to make drop down list to a column
-
Options of fetching mails from mail server into PI and also from oracle system
hi All, Pls extend your help in looking out the possiblity of fetching mails from mail server into SAP PI and also from oracle system into PI ,earliest help would be appreciated. and also the types of sources for both the scenarios. Regards Vidya Sag
-
/clr, /clrpure, /clrsafe, WinForm CodeDOM Error
Hi, Have converted a working vs2013 project to vs2015 preview and then CTP, I get a parser error when the WinForm designer tries to redraw the form. The converted code runs and compiles fine both in debug and release modes, and it seems the CodeDOM i
-
Pls. give some suggestion on Subsequent Credit and debit note?
Dear Gurus, Pls. give some suggestion on Subsequent Credit and debit note? Regrds Shikha