Battery low warning came on,took battery out and reloaded,r​an 5 minutes and stopped again

5

Hi, 
This is posted in the recovery forum, were you attempting to run a system recovery?  During the recovery you must have the battery and AC adapter in.

Similar Messages

  • I dropped my iPhone 4 in the sink where it was submerged in water for not even 2 seconds I took it out and put it in a warm room by the radiator and most of it works but no sound and battery length is short and runs out quickly. Any ideals on how to help?

    I dropped my iPhone 4 in the sink where it was submerged in water for not even 2 seconds I took it out and put it in a warm room by the radiator and most of it works but no sound and battery length is short and runs out quickly. Any ideals on how to help?

    $149
    They do not repair .Apple exchange and all returned units are refurbished at The Apple plants in China
    So you get a device that looks like and functions like new
    Are you familiar with the results of water and electricity mixing

  • My Macbook will not boot the operating system.  It just goes to a blue screen after the apple logo and the spinning wheel goes off.  I took the battery out and held the on/off button for five seconds and reset the PRAM.  I have the old mac os disk.

    My macbook will not boot.  It goes to a blue screen after the logo and wheel goes off.  I have taken the battery out and held the on/off button for five seconds and reset the PRAM.  I have the the original os disk but have not put it in for fear of losing un backed op data.
    Thanks
    Rich

    You won't lose any data unless you erase your hard drive.
    Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c"key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
    When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it.When it comes up is your Hard Drive in the list on the left?
    If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've selected the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.

  • Blackberry 8530 Curve will not download new pictures without taking battery out and resetting.

    Recently my BB 8530 will not download a new picture taken without taking the battery out and resetting. What is causing this issue?  Thank you.

    Hi and welcome to the forums haibieb!
    A couple of places for you to visit: Blackberry 101     Tips & Tricks
    And is the pic stored once you do a battery pull?
    Where are you storing your camera picS?  Media card or device memory?  and
    What is the setting on your reserve pictures memory? You may be exceeding that limit especially if your file size is too large.
    Let us know.  Happy to have you here!
    IrwinII
    Please remember to "Accept as Solution" the post which solved your thread. If I or someone else have helped you, please tell us you "Like" what we had to say at the bottom right of the post.

  • When apple iPhone 4s battery completely drain out and recharge again,no out going or incoming call can be sent or received

    when apple iPhone 4s battery completely drain out and recharge again,no out going or incoming call can be sent or received until rest the phone completly. Do we have any solution for this?

    The problem was only for calls and network and other functionlities were working fine. So i did reset  through settings-general-Reset-Reset all settings and re tried then it worked fine. But this is only a temporary solution  need a permanent fix.

  • Dv 6809wm laptop. Computer still does not boot up when battery out and ac adapter plugged in?

    dv 6809wm laptop. Computer still does not boot up when battery out and ac adapter plugged in?
    It lights up initially for a split second when I push power button, but does not continue to boot up. When ac adaptor is put in it glows blue like it is supposed to. Any suggestions?

    i'm going to try to see if a different ac adaptor will work hopefully that solves the issue.

  • We have a 2009 white macbook it got to 7% power was shut down wont recharge tried taking the battery out and magsafe nor light on the magsafe

    we have a 2009 white macbook it got to 7% power was shut down wont recharge tried taking the battery out and magsafe no light on the magsafe or power on the macbook? do we need a new magsafe or has the battery died?

    Hi degsy t,
    If you feel you may have potential battery or charger issues with your MacBook, you may find the troubleshooting steps in the following article helpful:
    Mac notebooks: All about batteries
    http://support.apple.com/kb/ht1446
    Regards,
    - Brenden

  • Today on the way to work it was raining heavily when i got to work my coat and pocket was soaked with my i phone 5 in it i took it out and wiped the screen off when i got to work and put it in my bag the likfe was on like 50% when i go on my break like 4

      today on the way to work it was raining heavily when i got to work my coat and pocket was soaked with my i phone 5 in it i took it out and wiped the screen off when i got to work and put it in my bag the likfe was on like 50% when i go on my break like 4 hours later my phone is dead and would not turn on for a while when it did it had some writting in the top left corner ive tried resseting my phone on i tunes and nothing has helped and the phone is relatively brand new so i need HELP?

    Hi Tone96,
    Based on your description, it sounds like you may need to have your iPhone serviced. You may find the following page helpful:
    Service Answer Center - iPhone
    http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipho ne
    Regards,
    - Brenden

  • "could not start the camera. Close other apps and try again"

    It shows up saying could not start the camera. Close other apps and try again when i try to open the camera but no other apps are open.
    how do i fix this?

    Hi.....i am new here and is not sure as yet how to start a new thread. 
    I have a bb curve 8310 and think i may ave caused my camera to stop working via uninstalling it....if that is possible. 
    wen i click on di camera it opens, makes shutter sound and flashes wen i click di trackball but after that it doesnt show di picture that it supposedlt took.
    Before this happened i was foolin around with the hide a folder option in pictures and not sure what i did wrong.......my video is not clear either.....please can you help me .....in addition i do not get any of those messages that i see the other users saying that they got for example could not start camera....i am not getting anything like that. all dat i get is a white screen......

  • Whenever I try to upload photos into iPhoto, they load but when importing it just stops a picyure or two into it and then just sits there. I can't stop the import so I have to shut off my camera when it is importing and start again. Help?

    Whenever I try to upload photos into iPhoto, they load but when importing it just stops a picture or two into it and then just sits there. I can't stop the import so I have to shut off my camera when it is importing and start again. Does anyone know how to fix this?

    As a test  launch iPhoto with the Option key held down and create a new, test library.  Tru importing from your camera to it and to see if the same problem persists. Does it?
    OT

  • Is it a common occurance for an iPad 4th gen to just blank out and stop working?  The screen shows nothing at all, no sounds but it registers on my computer when connected.

    Is it a common occurance for an iPad 4th gen to just blank out and stop working?  The screen shows nothing at all, no sounds but it registers on my computer when connected.

    A reset may help. Tap and hold the Home button and the On/Off buttons for approximately 10-15 seconds, until the Apple logo reappears. When the logo appears, release both buttons.
    No content is affected by this procedure.

  • HP G62 Battery causes slow boot - take battery out and boots normally - HP G62-340US Notebook

    All,
    Very strange thing going on, and I've not seen it on these forums, so here I go.
    Turn on laptop, the HP screen appears, and about 20 minutes later, Windows starts loading.
    Turn off laptop, pull the battery, turn on the laptop, and Windows starts loading within 10 seconds (normal).
    When the battery is in, EVERYTHING takes 15-20 minutes to start.  If I select F2 for settings, it takes that long.  If I hit F10 (or possibly F8), same delay.      If I take the battery out, it works perfectly.
    So....I of course assume bad battery......but I've never seen this type of behavoir in ANY computer previously.
    Any suggestions?
    HP G62-340US Notebook 
    Windows 7 Home Premium
    No error message and no changes made to system.
    Thanks
    Donlen

    Hi
    Have you tried to run the Start up test from F2 option did they pass.
    Please update the Bios, Graphic & Chipset driver from the HP website and have it checked.
    Hi
    Try this:
    Disconnect AC
    Shutdown
    Remove battery
    Connect AC
    Startup
    Open Device Manager
    Click the plus (+) sign next to Batteries category, right-click All of the "Microsoft ACPI Compliant Control Method Battery" listings, and select Uninstall In the "Confirm Device Uninstall" dialog box, click OK. (it’s ok if you only have 1 of these listings).
    Click the plus (+) sign next to System Devices.
    Right-click the “ACPI Fixed Features Button" and select Uninstall. In the "Confirm Device Uninstall" dialog box, click OK.
    Shutdown
    Disconnect AC
    Insert battery
    Connect AC
    Startup
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • Yosemite suddenly logs me out and in again

    Since updating to Yosemite I am facing some strange issues.
    While surfing of Working on my MacBook Pro (Late 2011) it suddenly logs me out and immediate in again.
    All open windows reappear but the whole startup procedure starts again.
    All connected or opened Drives and Images need to be reopened.
    As I'm working with this Computer also for my DJ-Gigs I think it's a very high risk at the moment to do a gig with this OS.
    I don't want to get logged out suddenly during the audience is listening to the music.
    Any guesses?
    Is it a bug or a new feature which can be switched off?
    I already checked for the Autologout after XX minutes of inactivity - it's not activated in my Preferences.

    When you have the problem, note the exact time: hour, minute, second.  
    These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    The title of the Console window should be All Messages. If it isn't, select
              SYSTEM LOG QUERIES ▹ All Messages
    from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar at the top of the screen.
    Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
    Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
    Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
    Please don't indiscriminately dump thousands of lines from the log into this discussion.
    Please don't post screenshots of log messages—post the text.
    Some private information, such as your name, may appear in the log. Anonymize before posting.

  • Took the battery out and put it back in, now I can't get the phone on!

    We were told that it was good for the phone if the battery were removed and put back in so it can reboot. I did that and I can't get the phone back on! Sometimes (not everytime) I'll get the red light to come on, but still nothing. I tried inseerting another bb battery from a Curve and when the red light came on, I held the 'end call' button and then when it went off I held the green 'make call' button and teh screen displayed a battery with a line through it. That same battery works fine in the curve so I am just confused about what else I should be trying.
    Can anyone help me out here??? 

    did you try to insert the pearl-battery and connect it to the wallcharger? maybe the battery is completly empty.
    does the screen display something? 
    If your question was answered, please accept it as a sollution and / or give Kudos ;-)
    Use the Search Field first! Maybe the question you want to ask already exists!

  • I used a clorox wipe to clean my macbook keyboard and some of the keys stopped working. I tried restarting and then all the keys stopped working. Now it won't turn on. I took the battery out and flipped it upside down to let it dry. help! what do I do?

    It really wasn't that much liquid but now I'm freaking out. I've always used clorox wipes and this has never happened to me. I'm going to leave it for a few days to dry just so I don't mess it up anymore. I'm debating putting it in rice. I just can't believe that small amount of liquid could ruin my macbook

    I just can't believe that small amount of liquid could ruin my macbook
    The traces (copper connections) on the logic boards are pretty close together.  It wouldn't take much to short two critical points out.
    I  hope putting it away for a few days (maybe in the warm sun) works for you.  Because that is all I would have suggested.

Maybe you are looking for

  • Synching problems...

    I recently went to the Genius bar when I was having probs, with several songs on my ipod in terms of freezing or skipping them, was told to restore and fix any songs that might have been typed in funny like for example one of the songs that skipped b

  • How to increase vram on hp pabilion 14?

    my hp product is hp paviloin 14 with 2.60 ghz processor,4 gb ram and 1.7gb total graphic memory but only 32 mb dedicated video memory....due to which i could play high  memory game....my motherboard is of intel and os is windows8......cant i increase

  • I have an ipod touch 2nd generation.is there is any other way to download apps which require ios4.3

    i have an ipod touch 2nd generation.is there is any other way to download apps which require ios4.3..please give me one solution.........

  • Second request; How canyou remove a power line with PS CC?

    Hi, I konw there is a terrific new feature in PS CC (I have used it before!) but I just can't find any explanation on how to to do it! The question is how do you remove, from an imge, a power line, or a telephone line by symply clicking on both ends

  • Printing of documents.

    Hi Experts, We require the functionality at the time of printing any marketing document for the below scenario. Scenario:When we are taking print of any documents first time than on documents it should show orginal and after in further sequence print