Battery saver mode stuck at 50% after changing to Linux.

Hello,
When I had W7P installed on my X1/2G, I turned on the battery saver mode.
Later, I decided to change the OS to Linux and didn't change it back to normal
battery mode and Linux (Debian) only seems to charge the battery to 50%.
Firstly, is this in fact a Windows lagacy issue and secondly, is there a command
or BIOS option that will reset the battery mode to full charge?
TIA.

Thanks for reply.
Followed the instructions for the install as per website
but I can't get the tp-smapi and acpi-call kernel modules
to load.
Apparently TLP has been known to work on the first
generation of X1 according to the ThinkWiki website
and should also work on the 2G model but I can't
even force load the modules as per FAQ.
Any Ideas?

Similar Messages

Streaming audio from my IPAD to my Apple TV from Rhapsody application. when Apple TV go into Screen Saver mode, about 5 minutes after that it stops playing the Audio Stream and goes into Sleep mode.

I am Streaming audio from my IPAD to my Apple TV from Rhapsody application. when Apple TV go into Screen Saver mode, about 5 minutes after that it stops playing the Audio Stream and goes into Sleep mode. I am using the Optical Out from the Apple TV to my receiver, the Apple TV is hard Wired to the Network, the IPAD is Wirelessly attached to the network (it continues to play the Audio Stream). When the Apple TV is turned back on it resumes playing once I manual select it for output from the IPAD. All device are on current releases of software. I have no Video hooked up to the Apple TV. How do I correct this?

Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment.

HT1476 can the phone be set to battery save mode?

I noticed that if I go to sleep and my battery is at 100% in the morning it is at 90% without it even being in use, is there a setting to put the phone on battery save mode?

I'm deaf in one ear too, and what I did was create the files in mono. I use the 320AAC format, which in mono, shows up as 160AAC and saves 1/2 the space on the hard drive or memory chip. SInce you already have stereo files, it's a simple matter to convert them all to mono, using iTunes. Go to the preferences and set the ripping to a mono-type format, choose all the songs in the library, and then convert them all. It might take hours for a large library, but it works fine.
I tried converter plugs but they were bulky and there's no simple way to solder the wires together in the tiny leads that go to the headphones that I use, so making mono files was my best option.

IPod mini stuck on Hold after changing battery

I just replaced the battery on my 4gb iPod Mini. prior to changing the battery, I moved the "lock" switch to the locked position (per the battery vendor's instructions). I replaced my battery & have twice restored the Mini to it's original settings, but the lock icon won't disappear when I toggle the switch. when I slide the as a result, I can't play anything. I can add music/podcasts to the Mini, but I can't play them. does anyone know how to fix this problem?

Try resetting the iPod mini by holding in the center button along with the up button. Hold it in until you see the Apple logo appear. If resetting it doesn't work, let me know.

I'm using lion 10.7.1 and ever since upgrading my preferances are not saved after I shut off the computer. My screen saver is always photos even after changing it, itune always asks if I want to upgrade, even after telling it never to.

When I turn off the computer my preferances are forgot. My screen saver aways goes to photos. Ittune always ask if I want to upgrade even after telling it not to . firefox always goes the upgrade page a progam I have to save my clipboard resets itself.

This does appear to be an issue with synergy, but I've also noticed on my C2D Macbook Pro that the screen does not wake from sleep when I simply touch or move around on the touchpad. Now, I have to hit a button (like return) to get the monitor to wake up. Submitting a button strike through synergy does not work, though. Neither does a mouse click on either the trackpad or through synergy.
It also appears that synergy is functioning even though the monitor is off. My mouse does move to the screen and progress across it (I have a three monitor setup with the Mac in the middle, so I can move it off my left system to my Mac, keep moving, and eventually it will show up on the third screen). If synergy weren't working, I would expect it to go from screen 1 to screen 3.
So I think there's something up with how Lion detects that the monitor should be reenabled, and synergy is even more affected by that decision.

Battery Saver stuck...

Hello everyone...
From yesterday night my battery saver has stuck... Look at the photo at the bottom of this post, to understand...
All those bars are from the background... I am 99% sure that the apps are not running in the background because I dont have any battery drain... So, I suppose "Battery Saver" has the problem...
I tried 4 or 5 soft resets but nothing... I also charge it full...
Have you any other possible solutions???
Thank you...
Lumia 1020 -> The apotheosis of Nokia
Attachments:
wp_ss_20140502.jpg ‏70 KB

I dont have "Battery Saver" ON.. Never...
And I checked everyone app... As I told in the first post, the entire "bar" comes from the "App in background"...
Thanks for the reply...
Lumia 1020 -> The apotheosis of Nokia

Battery saver automatically turns down alarm volume

When my phone's battery (Droid RAZR M) got down to 30%, a notification asked if I wanted to go into battery saver mode. I then set my phone to automatically go into battery saver mode at 30%. Twice now I have slept through my alarms because the alarm volume was turned way down. I'm assuming the battery saver is doing this, because that's the only thing I've changed on my phone since it's happened. I can't figure out how to disable the battery saver mode. I can't find it anywhere on my phone, and am wondering if someone could tell me where it is. I know there are multiple battery saver apps, but I have no idea which one it is because I can't find a battery saver anywhere on my phone. I'm assuming whatever app it is came with the phone.
Thanks!
Tyler

I know the alarm is an important function to rely on thans2316. You mentioned you set the phone for battery saver mode at 30%. This is a function built into the device. Have you tried adjusting the percentage? How about keeping the device on the charger at night, which would prevent it from getting to 30%?
JonathanK_VZW
VZWSupport
Follow Us on Twitter@VZWSupport

U 160 won't start after changing Ram from 4 to 8 Gig

Hey community,
I just installed two brand new DDR3-RAM 1066 MHz 7-7-7-20 204pin SO-DIMM Corsair modules to enhance my U160 a little bit. It runs a Win 7 Home Pro 64 and already was upgraded with a Samsung 250 Gig SSD.
The BIOS shows the RAM correctly but no matter if I try to boot normal or in save mode, the laptop reboots after the windows colours appear during start. "Last known version" also does not help, neither letting it start via a bootalble pen of which I further installed this Windows version. Because there is no blue or black screen I guess it is not a physical prob but a win prob.
Anybody an idea?
Thanks in advance,
Baschdel
Solved!
Go to Solution.

Nope, according to the German Lenovo board it accepts 8 Gig of RAM (use google translator):
http://thinkpad-forum.de/threads/144212-Ideapad-U160-Wieviel-RAM-m%C3%B6glich
I tried ubuntu but does not even load the data of the stick. I will try your hint with memtest now, looks like it really could be a prob with the RAM. By the way, it is 2x4 Gig Corsair Value Select.
Edit: I just checked the big onlineseller with the "a" and about 30% of the reviewers have incompatibility. I tried a different ubuntu and it loads about 20 seconds before it shuts down the computer. With the old RAM it works just fine so I guess I won't have to check via memtest and can declare that modules as falty.
thx

Lumia Battery Saver Settings

I'm using a Lumia 1520, and was wondering if there is somewhere to adjust settings for battery saver. I mean to configure when to start battery saver, select options to reduce or disable when mode is on...etc.
Used to have an Andriod phone and it had all such settings.
Thanx in advance.
Solved!
Go to Solution.

Apart from setting the battery saver to come on when battery is low, there is little you can do other than to manually start battery save mode. I find a decent battery monitor app help[s and Insider Pro gives accurate info and easy access to most functions, worth a try , it may help even if it doesn't solve your issue.
Good Luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Does iPad Air have a sleep/energy saver mode?

Hello~
I just bought this iPad (first one) and can't find anything about a "sleep" or "battery saver" mode. I don't want to turn it off, but I don't need it sitting there glowing. Plus, can't that hurt the screen?
Thanks!
Jenny

OMG. I feel like an idiot. I've looked everywhere, but for some reason never opened that menu item. THANK YOU SOOOOOOOO MUCH!!!!! You ROCK!!!!

My ipad 2's battery percentage is stuck at 95%!!! Eventhough I charge 5 hours, it is still 95%...After that, I unplugged the charger, I use my ipad for 3 hours, it is still 95%!!!!! What's wrong is it?! HELP ME

My ipad 2's battery percentage is stuck at 95%!!! Eventhough I charge 5 hours, it is still 95%...After that, I unplugged the charger, I use my ipad for 3 hours, it is still 95%!!!!! What's wrong is it?! HELP ME

You probably need to recalibrate the battery. See link below.
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
iPhone: Hardware troubleshooting (Power/Battery section also applies to iPad)
http://support.apple.com/kb/TS2802
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
iOS 7 Battery Life Draining Too Fast? It’s Easy to Fix
http://osxdaily.com/2013/09/19/ios-7-battery-life-fix/
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
iPad: Charging the battery
http://support.apple.com/kb/HT4060
Best Practices for iPad Battery Charging
http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

W520 - now changes to "projector only" whenever display turns off in power save mode

I have my W520 in a dock with an external monitor. The display is configured to Extend - the external monitor is primary, and the desktop extends onto the W520 screen. I don't have a screen saver. I turn off the display after 30 minutes of inactivity. Until recently both the laptop and monitor screens would turn off after 30 minutes, and then both resume when I moved the mouse or pressed a key.
Recently, the system has started changing to "Projector Only" when the display turns off. After resuming from power save mode, only the external monitor activates, and the W520 screen is disabled. I have to use Fn-F6 to switch back to "Extend" to re-activate the laptop screen.
I have rebooted and re-saved the power plan.
Why has this happened, and how do I fix it?

Hi, timg11
I have a few questions so that I may gain a better grasp of this issue:
1) What is your machine type and model? You can find this information on the bottom of your machine. It should be in format XXXX-XXX.
2) What is your operating system?
3) Does this issue occur is the computer is not in the docking station? (Please try if you haven't already).
Thanks in advance,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

PowerMac G5 hangs after going into screen saver power save mode

I have a PowerMac G5 and it's been working fine, but as of late has been hanging. I had a couple of external disks on the machine ( Maxtor OneTouch II and a OneTouch III). I recently added two more OneTouch III and stripped the three OneTouch III's together in a RAID set. I'm wondering if that is causing the hangs, but I've also seen it hang without the RAID so I'm not convinced it's the RAID.
Anyway, I can't figure out what's causing it to hang, but it seems to hang at some point after the screen saver runs and then the screen goes into power saver mode. It's not hung right when it shuts down the monitor, but at some point after that.
When it gets in this mode, I can't remotely login using ssh and I can't seem to wake it up. What I end up having to do is to hold the power button down for several seconds until the machine powers off.
In an attempt to see what's going on, I set the OS X monitor power save mode to "never", but I don't think I left it that way long enough and I never saw it hang.
Does anyone have any debugging tips that would help me identify the culprit?

I've been having the same troubles lately. Seem
since the JAVA update. It hangs completely after the
screen is shut down. Every morning I have to reboot
with the power button.
I am also joining the crowd with this issue. I have a 15" Powerbook G4 that has acted normally until recently. Not sure exactly when it started, but about the same time as the recent updates. Similar behavior to the previous forum posts.
When I manually put the laptop to sleep it freezes up before it sleeps and the multi-language reboot warning comes up. This also happens if it is set to auto-sleep after xx minutes.
When I try to wake it up, the screen is black and the power light shows it is on and it never unfreezes or I get the reboot message.
I have tried everything I can think of to troubleshoot this. I just re-installed the 10.4.8 update over the exisiting one (using an external boot drive made with SuperDuper) and it still happens... BUT when I put the laptop to sleep with the startup drive being external, it seemed to behave properly. I can't figure this out since the external clone was made only minutes earlier from the laptop... and it works. I have zapped PRAM, and done the battery removal / power button reset.
Below is the "report" I have been getting - and sending to Apple. They must be getting tired of the many I have sent.
Any thoughts out there?
Thanks.
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000020 PC=0x00000000002FA2A4
Latest crash info for cpu 0:
Exception state (sv=0x32E70000)
PC=0x002FA2A4; MSR=0x00009030; DAR=0x00000020; DSISR=0x40000000; LR=0x002E31B0; R1=0x1793BCD0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x002E31B0 0x002AE920 0x002F2EF4 0x0003C884 0x000A9314
Proceeding back via exception chain:
Exception state (sv=0x32E70000)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x2D24BC80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000A7E04 0x000AB780
Proceeding back via exception chain:
Exception state (sv=0x32E70000)
PC=0x002FA2A4; MSR=0x00009030; DAR=0x00000020; DSISR=0x40000000; LR=0x002E31B0; R1=0x1793BCD0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x002E31B0 0x002AE920 0x002F2EF4 0x0003C884 0x000A9314
Exception state (sv=0x2D24BC80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Model: PowerBook5,8, BootROM 4.9.5f3, 1 processors, PowerPC G4 (1.5), 1.67 GHz, 1 GB
Graphics: ATI Mobility Radeon 9700, ATY,RV360M11, AGP, 128 MB
Memory Module: SODIMM0/J20STANDARD, 1 GB, DDR2 SDRAM, PC2-4200S-444
AirPort: AirPort Extreme, 405.1 (3.90.34.0.p18)
Modem: Jump, , V.92, Version 1.0,
Bluetooth: Version 1.7.8f2, 2 service, 0 devices, 1 incoming serial ports
Network Service: Built-in Ethernet, Ethernet, en0
PCI Card: pci106b,4318, sppci_othernetwork, SLOT-A
PCI Card: TXN,PCIXXXX-00, cardbus, PC Card
PCI Card: usb, usb, USB20
PCI Card: usb, usb, USB20
PCI Card: usb, ehci, USB20
Parallel ATA Device: Hitachi HTS721010G9AT00, 93.16 GB
Parallel ATA Device: MATSHITADVD-R UJ-846,
USB Device: Bluetooth HCI, , Up to 12 Mb/sec, 500 mA
USB Device: Apple Optical USB Mouse, Mitsumi Electric, Up to 1.5 Mb/sec, 500 mA
USB Device: Apple Internal Keyboard / Trackpad, Apple Computer, Up to 12 Mb/sec, 500 mA
15" G4 PowerBook 1.67 Mac OS X (10.4.8)
G5 2.7 Gig Mac OS X (10.4.4) 3 Gig ram
15" G4 PowerBook 1.67 Mac OS X (10.4.8)

HT1199 Why is mail stuck in a do-loop of "There is a problem" with the mail account after changing iCloud password? How can it be fixed?

After changing passwords for iCloud, Mail is stuck in a do-loop "There is a [problem..." The error appears in less than one second after responding "Later"

Nope. Turns out that even though I have two Macs running 10.9.4, the one in question doesn't get the SMTP settings changed by iCloud settings when the password is changed, so I had to "Edit" the account in Mail, plow down to the password settings for the Apple SMTP server, and change the password myself. Nothing in the System Preferences iCloud setting tab lets you change any settings on the local machine. Apple is sure they are controlling everything when you make changes in iCloud, but they are wrong. Identical versions of 10.9.4 are configured differently on two different Macs.

HT3176 my apple remote will not link to my appletv even after changing the battery

my apple remote will not link to my appletv even after changing the battery. can anyone help?

Your Apple TV may have become paired with another remote. Hold the remote close to and pointed at the Apple TV, hold down the menu and Rewind buttons together for 6 seconds or until you see a broken chain icon on screen.

Battery saver mode stuck at 50% after changing to Linux.

Similar Messages

Maybe you are looking for