Battery X, trouble powering up...I'm deep in the jungle, please help!

On Jan 14th I bought a new MacBook Pro 13" Retina from MicroCenter. I am traveling deep in the jungle in a remote part of Costa Rica and I started noticing that it wasn't holding a charge (at first I assumed it had just ran out and I didn't plug in the power cable properly). Yesterday I had to plug it in to power it up and I notice the battery has an "X" on it and says "No Batteries Available". I did a quick search online and decided to try a SMC reset so I shutdown the laptop, held Shift+Control+Option+Power, and tried to power it up but the computer would not turn on or do anything at all.
Next morning, comptuer was hot and fans were running high speed (it was not plugged into power overnight so it must have been accessing power somehow). Sometimes it powered up when clicking power button, sometimes nothing, sometimes the fans would start up. When it did power up, it wouldn't get past the grey screen before shutting down again. Then sometimes without even touching anything it would turn on again.
Been trying different keyboard startups but they don't seem to be working properly. Tried resetting PRAM with Command+Option+P+R but got nothing... holding down Option does nothing.... The only thing that turns the computer on is Command+R, but it only works if I release the buttons quickly...if I hold them down (trying to get it into Recovery mode) nothing happens. If I do manage to get it on, a few mins later it the window will pop up that say "are you sure you want to shut down?" but even if I click Cancle it shuts down, or just shuts down randomly.
Tried running Disk Utility and it can't complete Verifying Disk, it just instructs me to get into Recovery mode to repair disk which I haven't had any luck doing.
I have insurance through MicroCenter (same coverage as AppleCare + accidental) but I tried calling them and the Tech Support guy was useless... I have a lot of work I need to do here and would be happy enough if I could at least get it to work off of the power cable without the battery (even though that is tricky b/c we are running off of a generator so I would be limited to the hours that the generator is on) but I can't get anything done or do a proper Time Machine backup with it powering off randomly. There's no chance of getting to a Genius Bar or anything out here so you are my only hope! Please help me!!
Lauren

So this is not the computer that the device normally syncs with, iTunes is working exactly as designed.

Similar Messages

I don't know exactly when this started, but Winamp became my default search and homepage.. The homepage issue was easy, but the search issue is bigger than I expected. It ALWAYS uses Winamp (Powered by AOL) as my default search. Please help. Thank you.

I don't know exactly when this started, but Winamp became my default search and homepage.. The homepage issue was easy, but the search issue is bigger than I expected. It ALWAYS uses Winamp (Powered by AOL) as my default search. Please help. Thank you.

reinstall it but make sure to uncheck the box next to "make winamp my default search engine"
attached is screenshot from the part of installation proces where that checbox should be unchecked
hope this helps

I just bought a new computer and im having trouble with transferring my purchased songs to my iphone please help

im having trouble with tranferring my purchased songs to my iphone . The problem is that im using my house desktop windows computer because my laptop is broking and all my songs are mainly on that one . Right now im trying to see if i can tranfer my purchased songs from the desk top itunes to my iphone .Its not showing me options for my perdiciment please help!!.

Plug it in and sync it.
What is the issue?
It will erase the current content and replace with content from the new computer.

My phone(4s) switches off automatically at 20% and doesnt start till i cahrge it,and once i put it on charge it shows batterl level 28%,earlier my battery wud drain till 1% then it used to switch off please help

my phone(4s) switches off automatically at 20% and doesnt start till i cahrge it,and once i put it on charge it shows batterl level 28%,earlier my battery wud drain till 1% then it used to switch off please help

These are usually the features of a faulty battery. Restore iPhone Firmware with iTunes 10.7 or 11 on computer. See if better. If not, and there is Warranty or AppleCare make Genius reservation and take iPhone to Apple for resolution. If no Coverage, still make Genius reservation and take iPhone to Apple Store for free quick (minutes time) battery diagnostic testing.

HT1349 having trouble burning cd that i purchased from your store please help ?

having trouble burning cd that i purchased from your store, can you please help?

Go to I tunes store page, look to the far right and click on purchased.

I need an application which turn off wifi automaticly when my Ipod Toch is locked (for save battery charge), i hate every time to turn it off manually please help ASAP!!!

I need an application which turn off WiFi automaticly when my Ipod Toch is locked (for save battery charge)
I hate every time to turn it off manually when I go sleep please help ASAP!!!
If I forget to turn of wifi on my device after my 8hour dream it's battery will be discharged. and ofcourse alert do not ring. pls help urgent!!!
Thanks

Suggestion:
Turn off your device before bed.

TS4006 My iPhone is lost, but its battery died. And now I can't find it. Please help me?!

I lost my iPhone while I was outside, and it ran out of battery. So now I can't find it. Is there any way find my iPhone could still find it?

No, sorry not a chance. The device must be powered on and connected to a data network for Apple's find my iPhone to work.

G5 powered off: can't get it on again - please help

Argh. Sitting here working productively and lights out on my G5 tower. Can anyone tell me what process I should take to start trouble shooting. It must be hardware. Let me tell you where it stands now:
1) I use industrial surge protectors, all lights are on there, all other pieces of hardware plugged in are working fine.
2) I reset the surge protector anyway, powered surge protector down and then up, swapped the socket I have my G5 plugged into just to be sure and just to check if it is anything external
3) nothing seemed to cause the shutdown and power down of the G5. no spark, no bad weather, no static etc.
Should I assume that I need to take it right away to be fixed at apple? Motherboard maybe? Any help would be greatly appreciated in what measures I can take. I need to move swiftly. Not worried about data, I have a time machine backup and a bootable backup on site, but I need to know what I should do to get the box up and running. Any help would be great. Thanks!

Hi iPhotoStuff 2-
First I would check and see if you are covered by this: Power Mac G5 Repair Extension Program for Power Supply Issues
It does sound power supply related. Do any LEDs do anything: About the Power Mac G5 (Late 2005) diagnostic LEDs
Luck-
-DaddyPaycheck

My iPhone 3GS battery is draining much too quick I'm looking for solutions please help

How do you fix battery problem on an iPhone 3GS? Can I get a new battery?

Hi thanks for the tips but I have done most of them including deleting the multitasking bar daily. One of the problem I think is associated with the iCloud and the need to keep the wifi on pretty much at all time OR DO WE?
Not sure yet about iCloud and how to use it properly... Very little is said on how to integrate/sync my iPhone, iPad and my PC using iCloud.
Any advise on this would also be welcome.

Trouble with my T1's and E1's in the lab - please help.... :-)

I'm working through my CCIE Voice/Collaboration training materials and am just about finished with the physical construction of the lab. At this time I'm just going to install a new T1 card into my BR1 router and I'm trying to get my T1 to HQ (HQ router) and my E1 to BR2 (Branch2 router) up and running. I am enclosing the "show run", "show isdn status" and "show e1/t1 controller" outputs. I am using a 2801 for my HQ router, a 2851 for my PSTN/IP-WAN router, and a 2811 for my BR2 router.
I am using a T1 cable RJ-48C/RJ-48C. I'm embarassed to say it - but I don't have a cable tester at the time. I lended my backup out to a friend and my primary one is not working. I'm also not 100% sure that I'm using the correct cable. I have VWIC2-2MFT-T1/E1 cards in my routers and I have a 2851 (PSTN router) setup to give connectivity via the T1's to HQ and BR1 and E1 connectivity to BR2. I have taken the liberty of attaching my configs, as mentioned I don't think I have cable issues because this is the case with all my cables.
Main issue, in the "show isdn stat" the layer 1 status is "deactivated" and when I do a shut/no shut the status goes to "shutdown" and doesn't come back up despite my efforts to enable the interface. The only way to fix it is to reboot the router. I've got to be missing something - I just want to get my T1's and E1 up for my CCIE Lab. I'm building my lab based on the CCIE Voice specification and have the ability to get it modified eventually to fit the CCIE Collaboration lab.
***PLEASE go easy on me - I'm sure there is a fundamental configuration item or concept I'm not thinking about so I'm preparing to look like a fool - but that's okay....it's part of learning. :-) ***
Any help would be so much appreciated. All configs are pasted below.......
==========================================================
=================START OF BR2 CONFIG=======================
BR2_RTR#show controllers e1
E1 0/0/0 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20100222, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (895 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 895 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
BR2_RTR#show isdn stat
Global ISDN Switchtype = primary-net5
ISDN Serial0/0/0:15 interface
        dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
    Total Allocated ISDN CCBs = 0
BR2_RTR#show inventory
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811         , VID: V06 , SN: FTX1328A0D3
NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC11271UAU
NAME: "WAN Interface Card - Serial 2T on Slot 0 SubSlot 1", DESCR: "WAN Interface Card - Serial 2T"
PID: WIC-2T            , VID: V01, SN: 35759031
NAME: "PVDMII DSP SIMM with three DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP SIMM with three DSPs"
PID: PVDM2-48          , VID: V01 , SN: FOC12221GJE
NAME: "AIM Service Engine 0", DESCR: "AIM Service Engine"
PID: AIM-CUE           , VID: V03 , SN: FOC11505K9D
NAME: "16 Port 10BaseT/100BaseTX EtherSwitch on Slot 1", DESCR: "16 Port 10BaseT/100BaseTX EtherSwitch"
PID: NM-16ESW=         , VID: 1.0, SN: FOC09245Q0H
NAME: "Power daughter card for 16 port EtherSwitch NM on Slot 1 SubSlot 0", DESCR: "Power daughter card for 16 port EtherSwitch NM"
PID:                     , VID: 1.0, SN: FOC09243VGH
NAME: "Gigabit(1000BaseT) module for EtherSwitch NM on Slot 1 SubSlot 1", DESCR: "Gigabit(1000BaseT) module for EtherSwitch NM"
PID:                     , VID: 1.0, SN: FOC092034R1
BR2_RTR#
BR2_RTR#
BR2_RTR#
BR2_RTR#
BR2_RTR#
BR2_RTR#show run
Building configuration...
Current configuration : 9148 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname BR2_RTR
boot-start-marker
boot-end-marker
card type e1 0 0
enable secret 5 $1$kYuC$TYARPnIw8mjqiVM3CqM15.
no aaa new-model
clock timezone CET 1 0
clock summer-time CET recurring 1 Sun Apr 1:00 last Sun Oct 1:00
network-clock-participate wic 0
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 192.168.30.1 192.168.30.49
ip dhcp excluded-address 192.168.30.70 192.168.30.254
ip dhcp pool PHONES
network 192.168.30.0 255.255.255.0
default-router 192.168.30.1
option 150 ip 3.3.3.3
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
allow-connections sip to sip
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
registrar server expires max 600 min 60
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
voice class h323 1
h225 timeout tcp establish 3
voice register global
mode cme
source-address 3.3.3.3 port 5060
max-dn 20
max-pool 10
load 7960-7940 P0S3-08-6-00
authenticate register
tftp-path flash:
create profile sync 1684632613172238
voice register dn 1
number 3005
name BR2_Phone3
voice register dn 2
number 3006
name BR2_Phone4
voice register template 1
no conference enable
voice register dialplan 1
type 7940-7960-others
pattern 1 3...
pattern 2 999
voice register pool 1
id mac 0008.E31B.7CD4
type 7960
number 1 dn 1
template 1
dtmf-relay sip-notify
username 3005 password cisco
description 3214-3005
codec g711ulaw
voice translation-rule 1
rule 1 /^$3...$$/ /3214\1/
voice translation-rule 2
rule 1 /^32143/ /3/
rule 2 /^\+3432143/ /3/
voice translation-rule 3000
rule 1 /^3000/ /1002/
voice translation-profile 3000
translate called 3000
voice translation-profile 4digitDNIS
translate called 2
voice translation-profile 8digitANI
translate calling 1
voice-card 0
crypto pki token default removal timeout 0
license udi pid CISCO2811 sn FTX1328A0D3
redundancy
controller E1 0/0/0
pri-group timeslots 1-3,16
interface Loopback0
ip address 3.3.3.3 255.255.255.255
h323-gateway voip bind srcaddr 3.3.3.3
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
interface Service-Engine0/0
no ip address
interface FastEthernet0/1
no ip address
duplex auto
speed auto
interface FastEthernet0/1.21
description BR2-PHONES(RTR on a stick)
encapsulation dot1Q 21
ip address 192.168.30.1 255.255.255.0
interface FastEthernet0/1.22
description BR2-DATA(RTR on a stick)
encapsulation dot1Q 22
ip address 192.168.31.1 255.255.255.0
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bchan-number-order ascending
isdn outgoing display-ie
no cdp enable
interface Serial0/1/0
no ip address
shutdown
clock rate 2000000
interface Serial0/1/1
description BR2-RTR_IP-WAN
no ip address
encapsulation frame-relay IETF
no fair-queue
frame-relay lmi-type ansi
interface Serial0/1/1.1 point-to-point
ip address 10.1.1.2 255.255.255.128
frame-relay interface-dlci 301
interface FastEthernet1/0
description BR2-PHONE1
switchport mode trunk
switchport voice vlan 40
no ip address
spanning-tree portfast
interface FastEthernet1/1
description BR2-PHONE2
switchport mode trunk
switchport voice vlan 40
no ip address
spanning-tree portfast
interface FastEthernet1/2
no ip address
interface FastEthernet1/3
no ip address
interface FastEthernet1/4
no ip address
interface FastEthernet1/5
no ip address
interface FastEthernet1/6
no ip address
interface FastEthernet1/7
no ip address
interface FastEthernet1/8
no ip address
interface FastEthernet1/9
no ip address
interface FastEthernet1/10
no ip address
interface FastEthernet1/11
no ip address
interface FastEthernet1/12
no ip address
interface FastEthernet1/13
no ip address
interface FastEthernet1/14
no ip address
interface FastEthernet1/15
no ip address
interface GigabitEthernet1/0
no ip address
interface Vlan1
no ip address
interface Vlan30
description PHONES-VLAN-FOR-LAYER3-SWITCHING
no ip address
shutdown
interface Vlan31
description DATA-VLAN-FOR-LAYER3-SWITCHING
no ip address
shutdown
router ospf 1
network 3.3.3.3 0.0.0.0 area 0
network 10.1.1.0 0.0.0.255 area 0
network 192.168.30.0 0.0.0.255 area 0
network 192.168.31.0 0.0.0.255 area 0
network 192.168.0.0 0.0.255.255 area 0
ip forward-protocol nd
ip http server
no ip http secure-server
ip http path flash:/GUI
ip route 192.168.100.0 255.255.255.0 10.1.1.1
tftp-server flash:Desktops/320x212x12/CampusNight.png
tftp-server flash:Desktops/320x212x12/CiscoFountain.png
tftp-server flash:Desktops/320x212x12/MorroRock.png
tftp-server flash:Desktops/320x212x12/NantucketFlowers.png
tftp-server flash:Desktops/320x212x12/TN-CampusNight.png
tftp-server flash:Desktops/320x212x12/TN-CiscoFountain.png
tftp-server flash:Desktops/320x212x12/TN-Fountain.png
tftp-server flash:Desktops/320x212x12/TN-MorroRock.png
tftp-server flash:Desktops/320x212x12/TN-NantucketFlowers.png
tftp-server flash:Desktops/320x212x12/Fountain.png
tftp-server flash:Desktops/320x212x12/CiscoLogo.png
tftp-server flash:Desktops/320x212x12/TN-CiscoLogo.png
tftp-server flash:Desktops/320x212x12/List.xml
tftp-server flash:Desktops/320x216x16/List.xml
tftp-server flash:Desktops/320x212x16/List.xml
tftp-server flash:ringtones/Analog1.raw
tftp-server flash:ringtones/Analog2.raw
tftp-server flash:ringtones/AreYouThere.raw
tftp-server flash:ringtones/AreYouThereF.raw
tftp-server flash:ringtones/Bass.raw
tftp-server flash:ringtones/CallBack.raw
tftp-server flash:ringtones/Chime.raw
tftp-server flash:ringtones/Classic1.raw
tftp-server flash:ringtones/Classic2.raw
tftp-server flash:ringtones/ClockShop.raw
tftp-server flash:ringtones/DistinctiveRingList.xml
tftp-server flash:ringtones/Drums1.raw
tftp-server flash:ringtones/Drums2.raw
tftp-server flash:ringtones/FilmScore.raw
tftp-server flash:ringtones/HarpSynth.raw
tftp-server flash:ringtones/Jamaica.raw
tftp-server flash:ringtones/KotoEffect.raw
tftp-server flash:ringtones/MusicBox.raw
tftp-server flash:ringtones/Piano1.raw
tftp-server flash:ringtones/Piano2.raw
tftp-server flash:ringtones/Pop.raw
tftp-server flash:ringtones/Pulse1.raw
tftp-server flash:ringtones/Ring1.raw
tftp-server flash:ringtones/Ring2.raw
tftp-server flash:ringtones/Ring3.raw
tftp-server flash:ringtones/Ring4.raw
tftp-server flash:ringtones/Ring5.raw
tftp-server flash:ringtones/Ring6.raw
tftp-server flash:ringtones/Ring7.raw
tftp-server flash:ringtones/RingList.xml
tftp-server flash:ringtones/Sax1.raw
tftp-server flash:ringtones/Sax2.raw
tftp-server flash:ringtones/Vibe.raw
tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.loads alias P0S3-08-6-00.loads
tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.sb2 alias P0S3-08-6-00.sb2
tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.bin alias P0S3-08-6-00.bin
tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.sbn alias P0S3-08-6-00.sbn
control-plane
voice-port 0/0/0:15
translation-profile outgoing 4digitDNIS
mgcp profile default
dial-peer voice 999 pots
translation-profile outgoing 8digitANI
destination-pattern 999
port 0/0/0:15
forward-digits 3
dial-peer voice 1 voip
incoming called-number .
dial-peer voice 901134 pots
destination-pattern 901134T
port 0/0/0:15
dial-peer voice 3000 voip
translation-profile outgoing 3000
destination-pattern 3000
session target ipv4:192.168.15.23
voice-class codec 1
voice-class h323 1
telephony-service
no auto-reg-ephone
max-ephones 10
max-dn 20
ip source-address 3.3.3.3 port 2000
network-locale ES
time-format 24
date-format dd-mm-yy
max-conferences 8 gain -6
web admin system name admin password cisco
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Jan 23 2014 05:43:52
ephone-template 1
softkeys connected Hold Select Trnsfer Endcall HLog Park
ephone-dn 1
number 3001
name BR2_Phone1
ephone-dn 2
number 3002
name BR2_Phone2
ephone 1
device-security-mode none
description 3214-3001
mac-address 0008.A3FD.3A32
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7960
button 1:1
ephone 2
device-security-mode none
description 3214-3002
mac-address 0017.E0C6.E232
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7961
button 1:2
banner motd ^CBR2 ROUTER CUCME/CUE^C
line con 0
password cisco
logging synchronous
login
line aux 0
line 194
no activation-character
no exec
transport preferred none
transport input all
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password cisco
login
transport input all
line vty 5 15
password cisco
login
transport input all
scheduler allocate 20000 1000
ntp server 172.30.1.2
end
===========END OF BR2 CONFIG=================
===========START OF HQ CONFIG================
HQ-RTR#show inventory
NAME: "chassis", DESCR: "2801 chassis"
PID: CISCO2801         , VID: V02 , SN: FTX1016Y07Z
NAME: "motherboard", DESCR: "C2801 Motherboard with 2 Fast Ethernet"
PID: CISCO2801         , VID: V02 , SN: FOC10140N6M
NAME: "WIC/VIC 2", DESCR: "Two port T1 voice interface daughtercard"
PID: VWIC-2MFT-T1=     , VID: 1.0, SN: 32867042
NAME: "WIC/VIC/HWIC 3", DESCR: "WAN Interface Card - Serial 2T"
PID: WIC-2T=           , VID: 1.0, SN: 32195023
NAME: "PVDM 0", DESCR: "PVDMII DSP SIMM with three DSPs"
PID: PVDM2-48          , VID: V01 , SN: FOC132935YB
HQ-RTR#
HQ-RTR#show controllers t1
T1 0/2/0 is down.
Applique type is Channelized T1
Cablelength is long gain36 0db
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20090113, FPGA: 20, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (709 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 709 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
T1 0/2/1 is down.
Applique type is Channelized T1
Cablelength is long gain36 0db
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20090113, FPGA: 20, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (709 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 709 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
HQ-RTR#show isdn stat
Global ISDN Switchtype = primary-ni
ISDN Serial0/2/0:23 interface
        dsl 0, interface ISDN Switchtype = primary-ni
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
    Total Allocated ISDN CCBs = 0
HQ-RTR#
HQ-RTR#show run
Building configuration...
Current configuration : 6734 bytes
! Last configuration change at 02:32:03 UTC Tue Feb 4 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HQ-RTR
boot-start-marker
boot-end-marker
logging buffered 512000 informational
enable secret 5 $1$K8GP$JbYRetpgnaxvy2wnjrPDW/
no aaa new-model
network-clock-participate wic 2
dot11 syslog
ip source-route
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp excluded-address 192.168.12.1 192.168.12.10
ip dhcp excluded-address 192.168.13.1 192.168.13.10
ip dhcp excluded-address 192.168.14.1 192.168.14.10
ip dhcp excluded-address 192.168.16.1 192.168.16.10
ip dhcp excluded-address 192.168.17.1 192.168.17.10
ip dhcp pool HQ-BR1-Pool
import all
network 192.168.11.0 255.255.255.0
option 150 ip 10.10.210.10
default-router 192.168.11.1
domain-name proctorlabs.com
dns-server 8.8.4.4 8.8.8.8
lease 8
ip dhcp pool BR2-Pool
import all
network 192.168.12.0 255.255.255.0
option 150 ip 10.10.202.1
default-router 192.168.12.1
domain-name proctorlabs.com
dns-server 8.8.4.4 8.8.8.8
lease 8
ip dhcp pool PSTN-Pool
import all
network 192.168.13.0 255.255.255.0
option 150 ip 10.10.100.2
default-router 192.168.13.1
domain-name proctorlabs.com
dns-server 8.8.4.4 8.8.8.8
lease 8
ip dhcp pool Laptop-Pool
import all
network 192.168.14.0 255.255.255.0
default-router 192.168.14.1
domain-name proctorlabs.com
dns-server 8.8.4.4 8.8.8.8
lease 8
ip dhcp pool WIRELESS-HOME
import all
network 192.168.16.0 255.255.255.0
default-router 192.168.16.1
dns-server 8.8.8.8 4.2.2.2
domain-name proctorlabs.com
lease 8
ip cef
no ip domain lookup
ip domain name proctorlabs.com
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-ni
voice service voip
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
voice-card 0
crypto pki token default removal timeout 0
license udi pid CISCO2801 sn FTX1016Y07Z
archive
log config
hidekeys
controller T1 0/2/0
pri-group timeslots 1-3,24
controller T1 0/2/1
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
description (Outside Public Interface)
ip address dhcp
ip access-group FW-IN in
no ip unreachables
ip mtu 1300
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
no cdp enable
interface FastEthernet0/1
no ip address
duplex auto
speed auto
interface FastEthernet0/1.11
description (Inside Private Interface)
encapsulation dot1Q 11
ip address 192.168.11.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.12
description (Inside Private Interface)
encapsulation dot1Q 12
ip address 192.168.12.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.13
description (Inside Private Interface)
encapsulation dot1Q 13
ip address 192.168.13.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.14
description (Inside Private Interface)
encapsulation dot1Q 14
ip address 192.168.14.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.15
description LAB-SERVERS
encapsulation dot1Q 15
ip address 192.168.15.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.16
description WIRELESS-HOME
encapsulation dot1Q 16
ip address 192.168.16.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.17
description LAB-HQ-PHONES
encapsulation dot1Q 17
ip address 192.168.17.1 255.255.255.0
ip helper-address 192.168.15.22
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.18
description LAB-HQ-DATA
encapsulation dot1Q 18
ip address 192.168.18.1 255.255.255.0
ip helper-address 192.168.15.22
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.501
description PSTN-RTR_MGMT-NETWORK
encapsulation dot1Q 501
ip address 172.30.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface Serial0/2/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn outgoing display-ie
no cdp enable
interface Serial0/3/0
description HQ-RTR_IP-WAN
no ip address
encapsulation frame-relay IETF
no fair-queue
frame-relay lmi-type ansi
interface Serial0/3/0.1 point-to-point
ip address 10.1.1.1 255.255.255.128
ip ospf mtu-ignore
snmp trap link-status
frame-relay interface-dlci 103
interface Serial0/3/0.2 point-to-point
ip address 10.1.1.129 255.255.255.128
ip ospf mtu-ignore
snmp trap link-status
frame-relay interface-dlci 102
interface Serial0/3/1
no ip address
shutdown
clock rate 2000000
router ospf 1
network 1.1.1.1 0.0.0.0 area 0
network 10.1.1.0 0.0.0.255 area 0
network 172.30.1.0 0.0.0.3 area 0
network 192.168.0.0 0.0.255.255 area 0
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 101 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 10.0.0.1 254
ip route 192.168.100.0 255.255.255.0 172.30.1.2
ip route 0.0.0.0 0.0.0.0 dhcp
access-list 101 deny   ip 192.168.0.0 0.0.255.255 10.10.0.0 0.0.255.255
access-list 101 permit ip 192.168.0.0 0.0.255.255 any
access-list 102 permit udp any any eq bootps
access-list 102 permit udp any any eq bootpc
access-list 102 permit udp any eq bootpc any
access-list 102 permit udp any eq bootps any
disable-eadi
control-plane
voice-port 0/2/0:23
mgcp fax t38 ecm
mgcp profile default
dial-peer voice 91212 pots
description PSTN-CALLS-TO-NYC-AREA-CODE
destination-pattern 91212T
port 0/2/0:23
forward-digits all
dial-peer voice 1 pots
description INCOMING-DIAL-PEER_PSTN
incoming called-number .
direct-inward-dial
port 0/2/0:23
dial-peer voice 1000 voip
destination-pattern 2123941...
session protocol sipv2
session target ipv4:192.168.15.23
incoming called-number .
voice-class codec 1
dtmf-relay rtp-nte
no vad
dial-peer voice 1001 voip
preference 1
destination-pattern 2123941...
session protocol sipv2
session target ipv4:192.168.15.22
incoming called-number .
voice-class codec 1
dtmf-relay rtp-nte
no vad
sip-ua
retry invite 2
timers trying 300
line con 0
password cisco
logging synchronous
login
line aux 0
line vty 0 4
exec-timeout 30 0
privilege level 15
password cisco
logging synchronous
login
transport input telnet ssh
line vty 5 15
exec-timeout 30 0
privilege level 15
password cisco
logging synchronous
login
transport input telnet ssh
scheduler allocate 20000 1000
end
HQ-RTR#
=============END OF HQ CONFIG=============
=======START OF PSTN-IP-WAN_RTR CONFIG=========
PSTN_IP-WAN_RTR#show inventory
NAME: "2851 chassis", DESCR: "2851 chassis"
PID: CISCO2851         , VID: V01 , SN: FTX0922A1E7
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC11063UF9
NAME: "WAN Interface Card - Serial 2T on Slot 0 SubSlot 1", DESCR: "WAN Interface Card - Serial 2T"
PID: WIC-2T      , VID: V01, SN: 35845606
NAME: "Two port T1 voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "Two port T1 voice interface daughtercard"
PID: VWIC-2MFT-T1=     , VID: 1.0, SN: 29803060
NAME: "WAN Interface Card - Serial 2T on Slot 0 SubSlot 3", DESCR: "WAN Interface Card - Serial 2T"
PID: WIC-2T=           , VID: 1.0, SN: 23188546
NAME: "PVDMII DSP SIMM with Two DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with Two DSPs"
PID: PVDM2-32          , VID: V01 , SN: FOC12045356
PSTN_IP-WAN_RTR#show controllers t1
T1 0/2/0 is down.
Applique type is Channelized T1
Cablelength is long gain36 0db
Description: HQ_T1
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20071129, FPGA: 20, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (852 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 852 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
T1 0/2/1 is down.
Applique type is Channelized T1
Cablelength is long gain36 0db
Description: BR1_T1
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20071129, FPGA: 20, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (854 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 854 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
PSTN_IP-WAN_RTR#show controllers e1
E1 0/0/0 is down.
Applique type is Channelized E1 - balanced
Cablelength is Unknown
Description: BR2_E1
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20071011, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
Data in current interval (862 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 862 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 0/0/1 is down.
Applique type is Channelized E1 - balanced
Cablelength is Unknown
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20071011, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
Data in current interval (864 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 864 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
PSTN_IP-WAN_RTR#
PSTN_IP-WAN_RTR#
PSTN_IP-WAN_RTR#show isdn status
Global ISDN Switchtype = primary-net5
ISDN Serial0/0/0:15 interface
        ******* Network side configuration *******
        dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
ISDN Serial0/0/1:15 interface
        ******* Network side configuration *******
        dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
ISDN Serial0/2/0:23 interface
        ******* Network side configuration *******
        dsl 2, interface ISDN Switchtype = primary-ni
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 2 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
ISDN Serial0/2/1:23 interface
        ******* Network side configuration *******
        dsl 3, interface ISDN Switchtype = primary-ni
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 3 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
    Total Allocated ISDN CCBs = 0
PSTN_IP-WAN_RTR#
PSTN_IP-WAN_RTR#show run
Building configuration...
Current configuration : 6518 bytes
! Last configuration change at 23:02:02 CST Tue Feb 4 2014
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname PSTN_IP-WAN_RTR
boot-start-marker
boot-end-marker
card type e1 0 0
logging message-counter syslog
enable secret 5 $1$rLlG$MPPST59p5rs0FfXu8OXp1.
no aaa new-model
clock timezone CST -6
clock summer-time CDT recurring
network-clock-participate wic 0
network-clock-participate wic 2
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 192.168.100.1 192.168.100.10
ip dhcp pool PSTN-PHONE
   network 192.168.100.0 255.255.255.0
   default-router 192.168.100.1
   option 150 ip 192.168.100.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
frame-relay switching
isdn switch-type primary-net5
voice translation-rule 1
rule 1 /^011$.*$/ /\1/
rule 2 /^1$.*$/ /&/
rule 3 /^00$.*$/ /\1/
rule 4 /^617$.*$/ /1&/
rule 5 /^212$.*$/ /1&/
voice translation-rule 2
rule 1 /^617/ /1&/
rule 2 /^212/ /1&/
voice translation-rule 3
rule 1 /^212/ /1&/
rule 2 /^34/ /&/
voice translation-rule 4
rule 1 /^617/ /1&/
rule 2 /^34/ /&/
voice translation-profile BR1-OUT
translate calling 3
voice translation-profile BR2-OUT
translate calling 2
voice translation-profile HQ-OUT
translate calling 4
voice translation-profile PSTN-IN
translate called 1
voice-card 0
crypto pki token default removal timeout 0
archive
log config
hidekeys
controller E1 0/0/0
clock source internal
pri-group timeslots 1-3,16
description BR2_E1
controller E1 0/0/1
clock source internal
pri-group timeslots 1-3,16
controller T1 0/2/0
clock source internal
pri-group timeslots 1-3,24
description HQ_T1
controller T1 0/2/1
clock source internal
pri-group timeslots 1-3,24
description BR1_T1
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0.13
description PSTN-PHONE_LAN
encapsulation dot1Q 13
ip address 192.168.100.1 255.255.255.0
interface GigabitEthernet0/1
description MGMT-CONNECTION-via-WIFI
ip address 172.30.1.2 255.255.255.0
duplex auto
speed auto
interface Serial0/0/0:15
description BR2-PSTN-CONNECTION
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
interface Serial0/0/1:15
description BR2-PSTN-CONNECTION
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
interface Serial0/1/0
description FR_to_BR2-RTR
no ip address
encapsulation frame-relay IETF
clock rate 64000
frame-relay lmi-type ansi
frame-relay intf-type dce
frame-relay route 301 interface Serial0/3/0 103
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
interface Serial0/2/0:23
description HQ-PSTN-CONNECTION
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
interface Serial0/2/1:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
interface Serial0/3/0
description FR_to_HQ-RTR_point-to-point-BR1andBR2
no ip address
encapsulation frame-relay IETF
clock rate 64000
frame-relay lmi-type ansi
frame-relay intf-type dce
frame-relay route 102 interface Serial0/3/1 201
frame-relay route 103 interface Serial0/1/0 301
interface Serial0/3/1
description FR_to_BR1-RTR-to-HQ-RTR
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
frame-relay intf-type dce
frame-relay route 201 interface Serial0/3/0 102
ip forward-protocol nd
ip route 1.1.1.1 255.255.255.255 172.30.1.1
ip route 2.2.2.2 255.255.255.255 172.30.1.1
ip route 3.3.3.3 255.255.255.255 172.30.1.1
ip route 10.1.1.0 255.255.255.0 172.30.1.1
ip route 192.168.14.0 255.255.255.0 172.30.1.1
ip route 192.168.15.0 255.255.255.0 172.30.1.1
ip route 192.168.16.0 255.255.255.0 172.30.1.1
ip route 192.168.17.0 255.255.255.0 172.30.1.1
ip route 192.168.20.0 255.255.255.0 172.30.1.1
ip route 192.168.21.0 255.255.255.0 172.30.1.1
ip route 192.168.30.0 255.255.255.0 172.30.1.1
ip route 192.168.31.0 255.255.255.0 172.30.1.1
no ip http server
no ip http secure-server
tftp-server flash:P0030801SR02.bin
tftp-server flash:P0030801SR02.loads
tftp-server flash:P0030801SR02.sb2
tftp-server flash:P0030801SR02.sbn
tftp-server P0030801SR02.txt
control-plane
voice-port 0/0/0:15
voice-port 0/2/0:23
voice-port 0/0/1:15
voice-port 0/2/1:23
ccm-manager fax protocol cisco
mgcp fax t38 ecm
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
dial-peer voice 10 pots
description HQ-NATIONAL-CALLS-DIAL-PEER
destination-pattern 2123941...
port 0/2/0:23
forward-digits all
dial-peer voice 20 pots
description BR1-NATIONAL-CALLS-DIAL-PEER
destination-pattern 6178632...
port 0/2/1:23
forward-digits all
dial-peer voice 30 pots
description BR2-NATIONAL-CALLS-DIAL-PEER
destination-pattern 32143...
port 0/0/0:15
forward-digits all
dial-peer voice 31 pots
description BR2-INTL-CALLS-DIAL-PEER
destination-pattern 3432143...
port 0/0/0:15
forward-digits all
telephony-service
em logout 0:0 0:0 0:0
max-ephones 2
max-dn 10
ip source-address 192.168.100.1 port 2000
load 7960-7940 P00303020214
keepalive 10
max-conferences 4 gain -6
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1
number 12123945001
label +8087812321
description NYC
name NYC-PSTN
ephone-dn 2
number 16178635001
label 911+999
description BOSTON
name BOSTON-PSTN
ephone-dn 3
number 32145001
label 18005551234
description SPAIN
name SPAIN-PSTN
ephone-dn 4
number 3432145002
description SPAIN
name SPAIN-PSTN-INTL
ephone-dn 5
number 5005
label 7812321
description 7812321
ephone-dn 6
number 5006
label x5005
description OFFICE PHONE
ephone 1
device-security-mode none
mac-address 0008.A3FD.39FF
type 7960
button 1:1 2:2 3:3 4:4
button 5:5
banner motd ^CC PSTN-IP-WAN ROUTER ^C
line con 0
password cisco
logging synchronous
login
line aux 0
line vty 0 4
password cisco
login
transport input all
line vty 5 15
password cisco
login
transport input all
scheduler allocate 20000 1000
ntp master
end
PSTN_IP-WAN_RTR#

I have went ahead and re-enabled the voice-ports just because I left that out of my original output. See below.....
Do you think I ordered 3 factory made T1 cables from BlackBox and ALL of them came back to me bad? Or perhaps they might not have made them as cross over cables......hmm...any other suggestions?
BR2_RTR(config)#voice-port 0/0/0:15
BR2_RTR(config-voiceport)#no shut
BR2_RTR(config-voiceport)#do sh voice port summ
BR2_RTR(config-voiceport)#do sh voice port summ
                                           IN       OUT
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0:15        01 isdn-voice up    down none     none     y
0/0/0:15        02 isdn-voice up    down none     none     y
0/0/0:15        03 isdn-voice up    down none     none     y
50/0/1          1      efxs     up    dorm on-hook idle     y
50/0/2          1      efxs     up    dorm on-hook idle     y
PWR FAILOVER PORT        PSTN FAILOVER PORT
=================        ==================
HQ-RTR(config)#voice-port 0/2/0:23
HQ-RTR(config-voiceport)#no shut
HQ-RTR(config-voiceport)#
HQ-RTR(config-voiceport)#
HQ-RTR(config-voiceport)#do sh voice port summ
                                           IN       OUT
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/2/0:23        01 isdn-voice up    down none     none     y
0/2/0:23        02 isdn-voice up    down none     none     y
0/2/0:23        03 isdn-voice up    down none     none     y
PWR FAILOVER PORT        PSTN FAILOVER PORT
=================        ==================
PSTN_IP-WAN_RTR#conf t
Enter configuration commands, one per line. End with CNTL/Z.
PSTN_IP-WAN_RTR(config)#voice-p
PSTN_IP-WAN_RTR(config)#voice-port 0/0/0:15
PSTN_IP-WAN_RTR(config-voiceport)#no shut
PSTN_IP-WAN_RTR(config-voiceport)#exit
PSTN_IP-WAN_RTR(config)#voice-por
PSTN_IP-WAN_RTR(config)#voice-port 0/2/0:23
PSTN_IP-WAN_RTR(config-voiceport)#no shut
PSTN_IP-WAN_RTR(config-voiceport)#exit
PSTN_IP-WAN_RTR(config)#voice-por
PSTN_IP-WAN_RTR(config)#voice-port 0/0/1:15
PSTN_IP-WAN_RTR(config-voiceport)#no shut
PSTN_IP-WAN_RTR(config-voiceport)#exit
PSTN_IP-WAN_RTR(config)#voice-port 0/2/1:23
PSTN_IP-WAN_RTR(config-voiceport)#no shut
PSTN_IP-WAN_RTR(config-voiceport)#exit
PSTN_IP-WAN_RTR(config)#
PSTN_IP-WAN_RTR(config)#
PSTN_IP-WAN_RTR(config)#
PSTN_IP-WAN_RTR(config)#do sh voice port summ
                                           IN       OUT
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0:15        01 isdn-voice up    dorm none     none     y
0/0/0:15        02 isdn-voice up    dorm none     none     y
0/0/0:15        03 isdn-voice up    dorm none     none     y
0/2/0:23        01 isdn-voice up    dorm none     none     y
0/2/0:23        02 isdn-voice up    dorm none     none     y
0/2/0:23        03 isdn-voice up    dorm none     none     y
0/0/1:15        01 isdn-voice up    dorm none     none     y
0/0/1:15        02 isdn-voice up    dorm none     none     y
0/0/1:15        03 isdn-voice up    dorm none     none     y
0/2/1:23        01 isdn-voice up    dorm none     none     y
0/2/1:23        02 isdn-voice up    dorm none     none     y
0/2/1:23        03 isdn-voice up    dorm none     none     y
50/0/1          1      efxs     up    dorm on-hook idle     y
50/0/2          1      efxs     up    dorm on-hook idle     y
50/0/3          1      efxs     up    dorm on-hook idle     y
50/0/4          1      efxs     up    dorm on-hook idle     y
50/0/5          1      efxs     up    dorm on-hook idle     y
50/0/6          1      efxs     up    up   on-hook idle     y
PWR FAILOVER PORT        PSTN FAILOVER PORT
=================        ==================
PSTN_IP-WAN_RTR(config)#

I'm having troubles installing 10.6.3 on my Macbook Pro, PLEASE HELP

I'm getting the error that seems to happen to a lot of people: "(volume name)" can't be used because it doesn't use the GUID Partition Table scheme.
When I go to change the Volume Scheme in Disk Utility it's grayed out and says Current, and the Options button is also grayed out, so I can't touch either.
So I try to boot the machine using the Snow Leopard 10.6.3 disc by holding the "c" key during start-up (bong sound) and it spits the disc out and boots normally... is the SL disc not a boot disc as well? I don't care if i have to format the hard drive, I just want it to work with the newer operating system(s). I'm just worried I'll format my hard drive, go to boot with the disc, and it'll pop it out again.
Please help. I'm losing hours at work trying to get this thing updated to Mavericks via Snow Leopard

Do a backup before proceeding.
Try putting the 10.6.3 disk in the computer. During a restart, hold down the option/alt key, select the disk, and see if you can boot from there. If so, select the language, then go to the Utilities menu, and select Disk Utility. Check to see what partition scheme you have by selecting the hard drive.
If you don't have GUID, you are going to need to erase the drive and reformat, which will cause you to lose all your data. Did I mention doing a backup?
If you do have GUID, run Disk Utility repair disk and repair permissions. You may have to do this more than once. Then try in install 10.6.3.
If successful, use the combo update to get to 10.6.8 and then run Software update until there are no more updates.
10.6.8 Combo Updater

My macbook is not connecting to wifi when working away from home (cafes,library etc). My phone connects no trouble but my laptop says connection timed out. Please help so that I can work away from home. Thank you

My laptop times out when connecting to wifi out of home. What do I need to do?
Please help.
Thank you.

Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)
Wireless Diagnostics - About
Also try turning off Bluetooth

I'm having trouble using Firefox 4 with Tor Project software. Please help. Will there be an updated Tor Button add-on for Firefox 4.0 soon? If not, how can I get rid of 4.0 and go to an earlier, but stable Firefox version?

I'm trying to use Tor Project for anonymous browsing. I updated my Firefox to 4.0, but I can't get a Tor Button to download, because it isn't available for Firefox 4.o.
Will it be soon?
If not, how do I go back to an earlier, stable version of Firefox that supports Tor Button browsing?
Thanks much!

See if the "stable" version released on 30 June is compatible with Firefox 5.0. That page doesn't mention which versions of Firefox it is compatible with, a serious oversight, IMO. <br />
https://www.torproject.org/torbutton/
Plus, it looks like that developer hasn't updated his AMO page in over a year, which makes it impossible for users of that add-on to get automatic updates as each new version of Firefox is released. <br />
https://addons.mozilla.org/en-US/firefox/addon/torbutton/

Trouble processing file in iOS4 update, tried EVERYTHING! PLEASE HELP

I downloaded iTunes 10.5, I troubleshooted the problem and I've tried everything in the books. When I'm downloading the file, it goes for about 45 minutes without a problem, then when the update reaches the point of "processing file", a screen pops up that says "network connection timed out". Please help, this has been a problem for me for about 3 days now.

Thanks, Wolf. I did follow those instructions to the letter. However, it
didn't help a bit.

Trouble importing favorites etc. from IE to Firefox. Please help. Thanks alot,

hen I tried several times to import favorites, etc. from IE to Firefox, I keep getting the same message- script busy or not responding.
Tried several times and nothing was imported and keep getting same message listed above. I have XP on my laptop.
Any suggestions or help is greatly appreciated. Thanks alot and have a great day!

Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
* Don't make any changes on the Safe mode start window.
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]
See also http://kb.mozillazine.org/Locked_or_damaged_places.sqlite
Other things that need attention:<br>
Your above posted system details show outdated plugin(s) with known security and stability risks that you should update.
# Adobe PDF Plug-In For Firefox and Netscape 8.2.5
# Shockwave Flash 10.1 r85
# Next Generation Java Plug-in 1.6.0_14 for Mozilla browsers
Update the [[Adobe Reader]] plugin to the latest version.
*http://get.adobe.com/reader/otherversions/
Update the [[Managing the Flash plugin|Flash]] plugin to the latest version.
*http://www.adobe.com/software/flash/about/
Update the [[Java]] plugin to the latest version.
*http://java.sun.com/javase/downloads/index.jsp (Java Platform: Download JRE)

Battery X, trouble powering up...I'm deep in the jungle, please help!

Similar Messages

Maybe you are looking for